American Standard 20DB.332211C.075 Dimensions Guide

Category
Sanitary ware
Type
Dimensions Guide

This manual is also suitable for

L13
© 2016 AS America Inc.
spec_20DB.332211C.075Tulsa33x22SSKitchenSinkKit1/16
TULSA
33 x 22 STAINLESS STEEL
KITCHEN SINK KIT
20 GAUGE STAINLESS STEEL
TULSA
33 x 22 STAINLESS STEEL
KITCHEN SINK KIT
20DB.332211C.07550/50DoubleBowlSink
Kit includes:
•Doublebowlsink
•Wastettings
•Coordinatingpull-downfaucet
•Installationinstructionsandcutouttemplate
•Topmountinstallationhardware
Stainless Steel Sink
•50/50DoubleBowl
•20GaugeStainlessSteel
•18-10ChromeNickelcontent
•Dualmountinstallation
•36"(914mm)cabinetrequired
•LimitedLifetimeWarranty
Nominal Dimensions:
33"x22"x9"
(838x559x229mm)
Bowl Size (equal size bowls):
14-9/16"(370mm)wide
19-7/16"(493mm)fronttoback
9"(229mm)deep
Pull-Down Faucet
•1.8gpm
•Brassswivelspout
•Ceramicdiscvalvecartridgefordrip
freeperformance
•SprayandStreamFunctions
•LeadFree:Faucetcontains≤0.25%lead
contentbyweightedaverage
 •LimitedLifetimeWarranty
Strainer
•Standard3-1/2"(89mm)diameter
•LimitedLifetimeWarranty
SEEREVERSEFORROUGHING-INDIMENSIONS
ANDPRODUCTSPECIFICATIONS
Suggested Specications:
Color:StainlessSteel.075
FaucetFinish:StainlessSteel.075
WasteFittingFinish:StainlessSteel.075
Supplies:1/2"(13mm)IPSInlets
Compliance Certications - Meets or Exceeds
the Following Specications:
•SINK:
ASMEA112.19.3
•FAUCET:
ASMEA112.18.1
CSAB125.1
NSF61/Section9
NSF372
L14
© 2016 AS America Inc.
spec_20DB.332211C.075Tulsa33x22SSKitchenSinkKit1/16
TULSA
33 x 22 STAINLESS STEEL
KITCHEN SINK KIT
20 GAUGE STAINLESS STEEL
NOTES:
WERECOMMENDUSINGBASINASATEMPLATETODETERMINEPROPERCONTOUR.CUTCOUNTERTOP38MM(1-1/2")INSIDE
BASINCONTOUR.
*
DIMENSIONSSHOWNFORLOCATIONOFSUPPLIEDAND“P"TRAPARESUGGESTED.
SEALINGCOMPOUNDSUPPLIEDBYOTHERS.
IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.3.
Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages.
Ø1-3/8"
(35mm)
REINFORCEMENT BAR
FOR TOP MOUNTING,
4 PLACES
Ø4-3/4"
(120 mm)
Ø3-9/16"
(90 mm)
16-1/2"
(419 mm)
19-7/16"
(493 mm)
22"
(559 mm)
2-9/16"
(65 mm)
14-9/16"
(370 mm)
14-9/16"
(370 mm)
8-5/8"
(219 mm)
7-11/16"
(195 mm)
33"
(838 mm)
9"
(229 mm)
8-5/8"
(219 mm)
8-13/16"
(223 mm)
16-9/16"
(420 mm)
7-7/8"
(202 mm)
5-5/8"
(143 mm)
1-3/8" to 1-1/2"
(35 to 38 mm)
DIA. MOUNTING
HOLE
2-11/16" MAX.
(68 mm)
21-7/8"
(555 mm)
4-7/8"
(125 mm)
  • Page 1 1
  • Page 2 2

American Standard 20DB.332211C.075 Dimensions Guide

Category
Sanitary ware
Type
Dimensions Guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI