American Standard 20SB.332211C.075 Spec sheet

Category
Sanitary ware
Type
Spec sheet

This manual is also suitable for

American Standard 20SB.332211C.075.075 is a single-bowl stainless steel kitchen sink kit that includes a coordinating pull-down faucet, waste fitting, installation instructions, and cutout template. The sink is made of 20-gauge stainless steel with an 18-10 chrome-nickel content and is designed for dual-mount installation, requiring a 36" cabinet. The sink measures 33" x 22" x 9" and has a bowl size of 29-9/16" wide, 18-9/16" front to back at the widest point, and 9" deep. The faucet features a stainless steel finish, a 1.

American Standard 20SB.332211C.075.075 is a single-bowl stainless steel kitchen sink kit that includes a coordinating pull-down faucet, waste fitting, installation instructions, and cutout template. The sink is made of 20-gauge stainless steel with an 18-10 chrome-nickel content and is designed for dual-mount installation, requiring a 36" cabinet. The sink measures 33" x 22" x 9" and has a bowl size of 29-9/16" wide, 18-9/16" front to back at the widest point, and 9" deep. The faucet features a stainless steel finish, a 1.

L17
© 2016 AS America Inc.
spec_20SB.332211C.075Raleigh33x22SSKitchenSinkKit1/16
RALEIGH
33 x 22 STAINLESS STEEL
KITCHEN SINK KIT
20 GAUGE STAINLESS STEEL
RALEIGH
33 x 22 STAINLESS STEEL
KITCHEN SINK KIT
20SB.332211C.075SingleBowlSink
Kit includes:
•Singlebowlsink
•Wastetting
•Coordinatingpull-downfaucet
•Installationinstructionsandcutouttemplate
•Topmountinstallationhardware
Stainless Steel Sink
•SingleBowl
•20GaugeStainlessSteel
•18-10ChromeNickelcontent
•Dualmountinstallation
•36"(914mm)cabinetrequired
•LimitedLifetimeWarranty
Nominal Dimensions:
33"x22"x9"
(838x559x229mm)
Bowl Size:
29-9/16"(751mm)wide
18-9/16"(472mm)fronttobackatwidestpoint
9"(229mm)deep
Pull-Down Faucet
•1.8gpm
•Brassswivelspout
•Ceramicdiscvalvecartridgefordrip
freeperformance
•SprayandStreamFunctions
•LeadFree:Faucetcontains≤0.25%lead
contentbyweightedaverage
 •LimitedLifetimeWarranty
Strainer
•Standard3-1/2"(89mm)drainassembly
•LimitedLifetimeWarranty
SEEREVERSEFORROUGHING-INDIMENSIONS
ANDPRODUCTSPECIFICATIONS
Suggested Specications:
Color:StainlessSteel.075
FaucetFinish:StainlessSteel.075
WasteFittingFinish:StainlessSteel.075
Supplies:1/2"(13mm)IPSInlets
Compliance Certications - Meets or Exceeds
the Following Specications:
•SINK:
ASMEA112.19.3
•FAUCET:
ASMEA112.18.1
CSAB125.1
NSF61/Section9
NSF372
L18
© 2016 AS America Inc.
spec_20SB.332211C.075Raleigh33x22SSKitchenSinkKit1/16
RALEIGH
33 x 22 STAINLESS STEEL
KITCHEN SINK KIT
20 GAUGE STAINLESS STEEL
NOTES:
WERECOMMENDUSINGBASINASATEMPLATETODETERMINEPROPERCONTOUR.CUTCOUNTERTOP38MM(1-1/2")INSIDE
BASINCONTOUR.
*
DIMENSIONSSHOWNFORLOCATIONOFSUPPLIEDAND“P"TRAPARESUGGESTED.
SEALINGCOMPOUNDSUPPLIEDBYOTHERS.
IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.3.
Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages.
Ø1-3/8"
(35mm)
REINFORCEMENT BAR FOR
TOP MOUNTING, 4 PLACES
Ø4-15/16"
(125 mm)
Ø3-9/16"
(90 mm)
2-7/8"
(73 mm)
15-1/4"
(387 mm)
29-9/16"
(751 mm)
9-1/16"
(230 mm)
22"
(559 mm)
33"
(838 mm)
9"
(229 mm)
18-9/16"
(472 mm)
10-15/16"
(277 mm)
13-11/16"
(348 mm)
8-11/16"
(220 mm)
16-9/16"
(420 mm)
10-1/16"
(255 mm)
5-3/4"
(146 mm)
1-3/8" to 1-1/2"
(35 to 38 mm)
DIA. MOUNTING
HOLE
2-11/16" MAX.
(68 mm)
21-7/8"
(555 mm)
4-7/8"
(124 mm)
  • Page 1 1
  • Page 2 2

American Standard 20SB.332211C.075 Spec sheet

Category
Sanitary ware
Type
Spec sheet
This manual is also suitable for

American Standard 20SB.332211C.075.075 is a single-bowl stainless steel kitchen sink kit that includes a coordinating pull-down faucet, waste fitting, installation instructions, and cutout template. The sink is made of 20-gauge stainless steel with an 18-10 chrome-nickel content and is designed for dual-mount installation, requiring a 36" cabinet. The sink measures 33" x 22" x 9" and has a bowl size of 29-9/16" wide, 18-9/16" front to back at the widest point, and 9" deep. The faucet features a stainless steel finish, a 1.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI