Ferm CSM1028 Owner's manual

Type
Owner's manual

This manual is also suitable for

Art.no. CSM1028
FPCS-1800
www.ferm.com
0807-21.1
DK
N
FIN
S
I
P
E
F
NL
D
GB
USERS MANUAL 06
GEBRAUCHSANWEISUNG 10
GEBRUIKSAANWIJZING 14
MODE D’EMPLOI 19
MANUAL DE INSTRUCCIONES 23
MANUAL DE INSTRUÇÕES 28
MANUALE UTILIZZATI 32
BRUKSANVISNING 37
KÄYTTÖOHJE 41
BRUKSANVISNING 45
BRUGERVEJLEDNING 49
GB
6 Ferm
CIRCULAR SAW
Thank you for buying this Ferm product.
By doing so you now have an excellent product,
delivered by one of Europe’s leading suppliers.
All products delivered to you by Ferm are
manufactured according to the highest standards
of performance and safety. As part of our
philosophy we also provide an excellent customer
service, backed by our comprehensive Warranty.
We hope you will enjoy using this product for many
years to come.
The numbers in the text refer to the diagrams
on pages 2 - 5.
Read the operating instructions carefully
before using this device. Familiarize
yourself with its functions and basic
operation. Service the device as per the
instructions to ensure that it always
functions properly. The operating
instructions and the accompanying
documentation must be kept in the
vicinity of the device.
Contents
1. Machine information
2. Safety instructions
3. Mounting accessories
4. Operation
5. Service & maintenance
1. MACHINE INFORMATION
Technical specifications
Voltage 18 V
Speed, no load 3800/min
Max. cutting depth at 90º 55 mm
Max. cutting depth at 45º 41 mm
Rated saw blade diameter 165 mm
Bevel angle 0-50 degrees
Saw blade dimensions Ø165xØ20x
1.0x1.6 mm
Number of teeth 24
Weight 3.5 kg
Lpa Sound pressure level 93.4 dB(A)
Lwa Sound power level 104.4 dB(A)
K = 3.0 dB(A)
Vibration 4.56 m/s
2
K = 1.5 m/s
2
Contents of packing
1 Circular saw
1 Saw blade
1 Rip fence
1 Wrench key
1 Operating instructions
1 Safety instructions
1 Warranty card
Check the appliance, any loose parts and
accessories for damage caused during transport.
Product information
Fig. A
Guard knob1.
Safety guard2.
Bolt3.
Retaining ring4.
Saw blade5.
Sole plate6.
Laser on/off button7.
Laser adjustment screw8.
Laser9.
Protractor10.
Saw angle clamping knob11.
Rip fence clamping knob12.
On/off switch13.
Spindle lock button14.
Lock off button15.
Cut depth clamping knob16.
Battery release button17.
LCD display18.
Dust extraction19.
2. SAFETY INSTRUCTIONS
Explanation of the symbols
Denotes risk of personal injury, loss of
life or damage to the tool in case of non-
observance of the instructions in this
manual.
Indicates electrical shock hazard.
Wear a dust mask. Working with wood,
metals and other materials may produce
dust that is harmful to health. Do not
work with material containing asbestos!
Caution!: Laserbeam! Never look into
the light beam and never aim the laser at
a person when it is switched on.
GB
7
Ferm
Before using the circular saw
Check the following points:
Is the saw blade missing any teeth or showing •
any cracks, it so must be replaced
immediately.
Make sure the blade is secure.•
Use this circular saw to saw only wood, wood-•
like products.
Do not use circular saw blades which are •
deformed or damaged.
Do not use HSS blades.•
Only use blades meeting the required •
dimensions, as well as data and descriptions;
Do not stop the blade of a circular saw by •
pressing the blade from the side.
Check that the blade guard can freely move •
and fully closes.
Never lock-up the guard in the open position.•
Never put sideward pressure on the blade. •
This may cause the blade to break.
Be careful when cutting wood with knots, nails •
or cracks in it and/or dirt on it, as these
can cause the blade to get stuck.•
Never leave the circular saw unattended.•
Use this circular saw to saw only wood or •
wood-like products.
Using circular saw.
Use clamps or a vice to hold the work.•
Never remove wood chips and saw dust that is •
close to the saw blade with your hands. If
there are small pieces of wood left between
the fixed and the movable parts, the circular
saw will have to be stopped. The plug needs
to be removed from the socket,
before any left piece can be removed.•
Check that the blade is suitable for the spindle •
speed of the circular saw. Do not attempt to
cut before the circular saw has reached full
speed. Make sure the circular saw runs
without load (i.e. is not in contact with the
work) when you switch it on. The circular saw
must have reached its full speed first.
Never cut wood that is thicker than the depth •
of the saw blade.
When cutting in wooden walls or floors, check •
there is no wiring or piping where you intend to
cut.
Switch off the tool and wait until the blade has •
stopped completely before moving the
saw away from the work or putting it down. •
Hearing protection should be worn when
Safety tips for the laser beamer
Never look into the light beam of the laser.•
Never point the light beam of the laser at •
humans or animals.
Do not point the light beam of the laser at •
strongly reflecting material. Hazard from
reflected light.•
Only have repairs made to the laser beamer •
by qualified personnel / professional repair
specialists.•
Do not insert any hard objects into the laser •
optics.
Clean the laser optics with a soft, dry brush.•
Switch off the machine immediately when you
discover:
A defective switch.•
Overheating of the circular saw.•
Smoke or odour caused by scorched •
insulation.
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
remove the battery.
Setting the sawing angle (bevel)
Fig. B
Loosen the saw angle clamping knob (11).•
Rotate the soleplate (6) in the correct position •
(0º - 50º) and tighten the saw angle clamping
knob. The sawing angle (bevel) can be read
on the protractor (10).
Fitting the rip fence
Fig. C
Loosen the rip fence clamping knob (12).•
Insert the rip fence into the slots provided.•
Set the correct cut width and thighten the rip •
fence clamping knob (12).
Setting the cutting depth
Fig. D
Pull out and loosen the cut depth clamping •
knob by turning it counter clockwise (16).
Caution! Do not turn the cut clamping
knob more than 1 full turn.
Move the soleplate (6) downwards.•
GB
8 Ferm
Pull out and tighten the cut depth clamping •
knob (16) once the correct depth is set. The
cut depth clamping knob needs to be pulled
out in order to function. Make sure it is
securely tightened before using the machine.
Exchanging or cleaning the saw blade
Fig. A + E + F
Press the spindle lock button (14) to prevent •
the spindle from rotating.
Loosen the bolt (3) in the centre of the saw •
blade, using the wrench key (20).
Release the spindle lock button (14).•
Turn the safety guard (2) to the rear and hold it •
there with the aid of the guard knob (1).
Remove the retaining ring (4) and the saw •
blade. Clean the blade or replace it with a new
one. Make sure the arrow on the saw blade,
indicating the direction of rotation,
corresponds with the direction arrow on the
upper guard.
Place the saw blade back on the shaft.•
Release the guard knob the allow the safety •
guard to return over the saw blade.
Press the spindle lock. Refit the retaining ring •
and firmly tighten the bolt.
Connecting and removing the battery
Fig. G
Insert the battery into the base of the •
appliance, as shown on the illustration. Push
the battery until it latches in.
Press the locking button (17) before removing •
the battery, and disengage the battery from
the base of the appliance.
Only use batteries of the following type.
Using any other batteries could cause
serious injury or damage the tool.
CDA1051: FPB-1800L, 18V Lithium-Ion.
CDA1053: FPB-1800N, 18V NiMH.
The following charger can be used to charge these
batteries.
CDA1052: FPL-1800 (Lithium-Ion and NiMH).
CDA1054: FPL-1800N (NiMH only).
4. OPERATION
Wear ear and eye protection.
Switching on and off
This machine is equipped with a safety switch.•
Start the machine by pressing the “lock off” •
button (to disengage the switch) and switch on
the machine.
Release the (On/Off) switch to switch the •
machine off.
Operation
Hold the work using clamps or a vice to have •
both hands free to operate the saw.
Switch on the saw and place the sole plate on •
the workpiece.
Slowly move the saw towards towards the •
previously drawn cutting line and slowly press
the tool forward.
Firmly press the soleplate on the workpiece •
otherwise the circular saw may start to vibrate,
causing the blade to break more easily.
Let the saw do the job. Do not put undue
pressure on the circular saw. If the saw
blade jams in the workpiece, the
machine will automatically switch off.
Laser beamer
Laser beamer in use
The leading beam of the laser beamer makes
sawing in straight lines much easier:
a) along a drawn line, or
b) by aligning it to a fixed point marked on the
workpiece. Press the laser on/off button (8) to
switch the laser on or off.
Adjusting the laser beam
Transport handling and heavy use can affect •
the precision of the laser beam.
The laser beam itself can be easily adjusted.•
Hold the blade of the circular saw against a •
straightedge or perfectly straight plank.
Switch the laser on. •
Check whether the laser beam runs parallel •
along the edge of the straightedge or plank.
GB
9
Ferm
If the laser beam is out of alignment, proceed •
as follows:
Hold the blade of the circular saw against •
a straightedge or perfectly straight plank.
Correct the laser such that it runs straight •
along the edge using the screws on the
side of the laser.
LCD display
Fig. H
This machine is equipped with an LCD display.
To turn the display on, press the display button •
(21) once. To turn the display off, press the
display button again.
The clock (22) and minutes (23) remaining •
icons indicate the number of minutes of
running time that are available before the
battery requires recharging (Lithium Ion
battery only)
The battery icon (24) indicates the amount of •
charge remaining in the battery. Each charge
bar displayed indicates approximately 10%
charge remaining in the battery. A total of 10
charge bars indicates a fully charged battery.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Cleaning
Keep the ventilation slots of the machine clean to
prevent overheating of the engine. Regularly clean
the machine housing with a soft cloth, preferably
after each use. Keep the ventilation slots free from
dust and dirt. If the dirt does not come off use a
soft cloth moistened with soapy water. Never use
solvents such as petrol, alcohol, ammonia water,
etc. These solvents may damage the plastic parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part,
please contact the service address on the
warranty card. In the back of this manual you find
an exploded view showing the parts that can be
ordered.
Environment
To prevent damage during transport, the appliance
is delivered in a solid packaging which consists
largely of reusable material.
Therefore please make use of options for recycling
the packaging.
Faulty and/or discarded electrical or
electronic apparatus have to be
collected at the appropriate recycling
locations.
Warranty
The warranty conditions can be found on the
separately enclosed warranty card.
54 Ferm
Spare parts list
CSM1028 - FPCS-1800
Position Description No.
1 Hexagonal screw 490079
3+4+32+77+78+80 Guard 490081
5+8+11+14+43+45+46 Housing 490082
6+7+9+21 Laser complete 490083
13+68+69 Spindle lock 490084
15 till 17 + 64 till 67 Gear box 490085
18 till 20 + 29 till 32 Depth lock 490086
22+23 Battery contacts 490065
24 till 27 Battery lock box 490087
28+79 Flange set 490080
33 Switch 490088
34+35 Lock off button 490089
36 till 38 +41+42 LCD display 490000
47 Air reflector 490090
48 PCB 490091
49+50 Motor 490092
54 till 57 + 60 till 63 Base plate 490093
58 Socket wrench 490094
59 Rip fence 490095
71 till 73 +19+74+75 Rubber cap complete 490096
10(10)+12+39(3)+40(9)+
44(3)+51(2)+52(4)+53(4)+
70(2)+76 Screws set 490097
2 Saw blade (24T) CSA1024
2 Saw blade (36T) CSA1026
55
Ferm
Exploded view
1
2
4
5
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
32
33
34
35
36
37
38
39
40
41
42
43
10
10
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
7
6
9
3
32
30
29
31
66
67
68
69
70
71
72
73
19
74
75
76
77
78
79
80
JD5383L18
28
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Ferm CSM1028 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI