ATJ211D
2
WARNINGS
Do not place naked flames, such as lighted candles on or near the product.
Do not place objects filled with liquids, such as vases on or near the product.
Do not use or store this product in a place where it is subject to direct sunlight, heat,
excessive dust or vibration.
Do not use this product with wet hands.
Do not clean this product with water or other liquids.
Do not block or cover the slots and holes in the product.
Do not push foreign objects into the slots or holes in the product.
Do not attempt to open this product yourself. There are no user serviceable parts inside.
Do not allow children access to plastic bags.
SAFETY WARNINGS
Before using this product, read and follow all warnings and instructions.
This product is not intended for use by young children. Young children should be properly
supervised.
This product is intended for household use only and not for commercial or industrial use.
Do not expose to dripping or splashing.
No naked flame sources, such as lighted candles, should be placed on the product.
Ventilation should not be impeded by covering ventilation openings with items such as
newspapers, table cloths, curtains and the like.
Make sure the unit is adjusted to a stable position. Damage caused by using this product in
an unstable position or by failure to follow any other warning or precaution contained
within this user manual will not be covered by warranty.
This device is not intended for use by people (including children) with physical, sensory or
mental disabilities, or a lack of experience and knowledge, unless they’re under supervision
or have received instructions about the correct use of the device by the person who is
responsible for their safety.
Lenco suggests to retaining the packaging in case for future transport of the product.
Prolonged exposure to loud sounds from personal music players may lead to
temporary or permanent hearing loss.
When participating in the traffic listening to a personal music player can make the
listener less aware of potential dangers such as approaching cars.
If at any time in the future you should need to dispose of this product please note that: All
batteries and accumulators need to be removed from this product (Removal of Waste Batteries
and Accumulators).
ATJ211D
3
1. Get to know the controls on Player
Item
Description
Item
Description
1
TFT Display
7
Mic Hole / Reset Switch Hole
2
Clip
8
(Previous / Fast-Backward)
3
(Volume Up)
9
(Next / Fast-Forward)
4
(Volume Down)
10
USB Mini Connector
5
Memory Card Slot
11
(Play / Pause / Standby ON - OFF)
6
Earphone Output Jack
12
M (Menu / Enter / Select)
2. About the Player’s Battery
The player has an internal, non-user-replaceable battery. For the best results, the first time you
use the player, let it charge for about 2 hours or until the battery status icon in the “Connect”
screen shows that the battery is full.
Battery is in full
Note: Player continues to use battery power after it’s been turned off, if unit isn’t used for a while,
the battery might need to be charged. Recharging the player at least 2 – 3 times in three months
for maintain the battery life and performance.
a. Charging the Battery:
You can charge the player battery in two ways:
Connect player to your computer. Or,
Use the USB power charger. (not included)
3
4
5
2
6
7
8
9
10
1
12
11
ATJ211D
4
b. Connection and Charging:
Once you have connected player with computer / power charger, then you will see the
“Connect” screen appear on screen,
The level bars are running in battery status icon at the “Connect” screen. The battery is in
charging.
“Connect” Screen
In Charging
Important: The battery does not charge when your computer is in sleep. The USB port on most
keyboards does not provide enough power to charge the player. Connect the player to a USB 2.0
port on your computer only to prevent the charging problem.
3. Connecting and Disconnecting Player
You can connect the player with your computer to transfer those media files and recorded voice
memos when necessary, and to charge the battery.
a. To Connect the Player
To connect the player to your computer, plug the connector of the USB Cable into a USB port
on your computer, and connect the other end to the player, then the “Connect” screen
appears for view.
Now the player is ready for media files transfer with your computer and the battery is
charging.
You can transfer the media files by using the computer mouse use drag and place, or copy and
paste, in between the player and your computer. Disconnect it when you’re done.
b. To Disconnecting Player
It’s important not to disconnect player while it’s syncing or transferring files. Eject the player
before disconnect it.
To eject the player, press and hold the M button for about 2 seconds, the “Connect” screen
will switch to “Main Menu” screen. And now it is safe to disconnect the player with your
computer. Unplug the USB cable from the player. Or,
If you’re using a Windows PC, you can also eject the player in My Computer or by clicking the
“Safely Remove Hardware” icon in the Windows system tray. Select the correspondent name
of the USB Device and choose “Stop” > choose “Confirm” > choose “Confirm” followed by the
pop up window of your computer.
If you’re using a Mac, you can also eject the player by dragging the player icon on the desktop
to the Trash.
ATJ211D
5
Disconnect the USB cable from the player and computer, simply remove it.
If you accidentally disconnect the player without ejecting it, reconnect it to your computer
and sync again. However, some media file may be lost.
4. Getting Started with the Player
Turning the player ON/OFF and using the Main Menu.
Press and hold the button for 3 – 4 seconds to turn ON the player, then you will see any
one of the following shown Main Menu screens, Music / Movie / Record / Pedometer /
Voice / Photo / Setup / Game / eBook, will appear on the LCD after the Loading and Opening
screen are displayed.
To turn OFF the player, press and hold the button for 3 – 4 seconds.
“Main Menu” screens
(If Music chooses) (If Movie chooses) (If Record chooses) (If Pedometer chooses)
(If Voice chooses) (If Photo chooses) (If Setup chooses) (If Game chooses)
(If eBook chooses)
5. Use the Setup Menu
You might need to set date & time or change some default setting as you desire in the setup sub
menu before you start to use the player.
ATJ211D
6
To go into the setup menu, from the main menu, choose “Setup” by using the /
button and then press the M button; a “Setup” menu appears to use.
You can go back to the previous menu by pressing the button during in setup menu. Or,
press and hold the M button to return to the main menu.
Setup Menu
(Menu Page 1) (Menu Page 2)
a. To Setup “System time” (Date & Time):
Choose “System time” by using the / button and then press the M button, a date &
time setting screen appears.
Press the “+” button, the year is highlighted; then adjust it to the current year by pressing the
/ button. Repeat the adjusting methods by the “+” and / button again to
finish the following items; Month, Date, Hour, Minute and seconds setting adjustment.
Finally, you need to press the M button to confirm the adjustment and go back to the Setup
menu, if not the date & time will not be memorized and you need to adjust them again.
b. To change “LCD set”
You can set the backlight to illuminate the screen for a certain amount of time as you desire or
make the backlight go ON permanently every time you turn ON the player.
To change the LCD backlight, choose “LCD set” > choose “Dark mode”, a level bar with
numbers appears; then choose “0 (always On) / 5 / 10 / 15 / 20 / 25 / 30 / 35 / 40 / 45 / 50
(seconds)” as you desire by using the M and / buttons. Choose “0” to prevent the
LCD backlight from turning off. (choosing this option decreases the battery performance)
c. To Change the “Language”
This player can use difference OSD languages.
To set the language, choose “Language”, and then choose the language as you desire by using
the M and / buttons.
d. To Set “Power Off”
The Power Off setting can extend the time between battery charges by turning OFF the player
when you are not using the controls or when there’s no operation. Also, the Sleep function is
provided for more choice.
To set power off time, choose “Power off”, then choose “Off time”, a level bar with numbered
menu appears, then choose “0 - 200 seconds” as you want by using the M and /
buttons.
To set the sleep time, choose “Power off”, then choose “Sleep time”, a level bar with
numbered menu appears, choose “0 / 10 / 20 /30 / 40 / 50 / 60 / 70 / 80 / 90 / 100 / 110 /
120 minutes” as you want by using the M and / buttons.
ATJ211D
7
e. To View “Memory info”
You can view the memory status of the player, such as the numbers of the remaining memory
space available and the percentage of memory that’s been used.
To view the status, choose “Memory info” by using the M and / buttons. An
information screen, remaining memory space available and percentage of memory used,
appear for viewing.
To return to the setup menu or main menu press the button or press and hold the M
button.
f. To View “Firmware Version”
You might need to view the details about firmware information inside the Player.
Choose “Firmware version” by using the M and / buttons, an information screen
appears for viewing.
To return to the setup menu or main menu, press the button or press and hold the M
button.
g. To “Exit”
Select Exit to go back to the main menu. Or, press and hold the M button to go back to the
main menu.
6. Use Music Menu
You can use the music player to playback with supported music file formats of audio coding; WMA
and MP3 are supported by the player. To open the music player in the Main Menu:
From the main menu, choose “Music” by using the / and M button, a “Music Now
Playing” screen appears.
“Music Now Playing” Screen
a. To Play Music
In the Music Now Playing screen, press the button to start playing.
Press the button to pause the playing music.
Press it again to resume.
b. Play Previous or Next Music
Press the button to play next music.
Press the button to play previous music.
c. Use Fast-Forward or Fast-Backward
Press and hold the button to use fast-forward
Press and hold the button to use fast-backward.
d. Adjust volume level
In music playing, press the button to increase the volume level, a change volume control
ATJ211D
8
screen appears.
In music playing, press the button to decrease the volume level, a change volume control
screen appears.
Wait for 6 – 8 seconds or press the button to return to the music now playing screen.
For hearing protection; a beep warning will be heard from the earphone, or display warning
pop-up on TFT screen, when every time you increase the volume level and reach to the default
setting level which may exceed 85dB. Press the M button to accept the warning and enter into the
volume control to increase the level up to the maximum level.
e. Use Lyric Display
This player supports “*.LRC” lyric files and lyrics can synchronously be displayed while playing
music if your music has lyrics included. How to know whether the lyrics exist? If the current song
has matching lyric files, the color dot beside the Lyric Message icon will turn to green from
red in the Music Now Playing screen.
Play the music with lyrics, and then press and hold the M button to enter the lyric display
mode and the lyrics are displayed and moved up accordingly with the playing music.
Press the M button to cancel the lyrics display and go back to the Music Now Play screen if
you want.
7. Use Music Submenu in Music Stop Mode
You might need to do some changes for music playing, such as repeat, EQ settings for music
files… etc. To change setting:
a. To Set “Repeat”
In music playing mode, press the M button, a music submenu “Repeat / Equalizer / Exit”
appear for use;
Choose “Repeat” > choose “Normal / Repeat one / Repeat all / Repeat folder / Random All /
Random Folder” as you desired by using the / and M buttons.
b. To Change “Equalizer”
Choose “Equalizer”, then choose “Natural / Rock / Pop / Classic / Soft / Jazz / DBB” as you
desired by using the / and M buttons.
The submenu will disappear in some seconds automatically. Or, press the button.
c. To Change “Equalizer”
Select Exit to back to music now playing screen.
8. Use Music Submenu in Music Stop Mode
You might need to selecting folders for music play and delete music files. To do this:
In Music Now Playing screen, press the button to stop the playing music if player is in
playing. Then,
Press the M button to pop-up the Music Submenu;
a. Local Folder
In Music Submenu screen, choose “Local folder” a list menu appear, and then select folder
and / or choose a music file by using the / and M buttons.
It will go back to music now playing screen once a music file is selected. Then press the
button to play.
ATJ211D
9
b. Artists
Choose “Artists” to enter folder(s) list menu grouping by Artist name, then choose who name
of Artist folder > choose a song file in list where start the play.
Album
Choose “Album” to enter folder(s) list menu grouping by Album name, then choose who
name of Album folder > choose a song file in list where start the play.
Genre
Choose “Genre” to enter folder(s) list menu grouping by Genres name, then choose who
name of Genres folder > choose a song file in list where start the play.
Update playlist
Choose “Update playlist” to update the playlist when you found it show incorrect; actually, it
is normal due to some media files could be manual deleted in player’s memory by user in
some case. However, update the playlist when necessary.
c. Delete file
Choose “Delete file”, a list menu appear, and then choose which music file that you want to
delete by using the / and M buttons.
Once file is selected, press the M button and choose Yes to confirm or No to cancel.
Press the M button to confirm.
d. Delete All
Choose “Delete all”, a dialog appear to choose, then selects “Yes / No” by using the /
and M buttons.
Choose Yes to confirm or No to cancel and press the M button to confirm.
All music files will be deleted once YES is selected and confirmed, a “Deleting” screen appear
for a while and deleting process is in progress, then “Empty disk!” message will show on
screen for few seconds.
e. Exit
Select Exit to back to music now playing screen.
9. Use Movie Menu
a. To Play Movie
From the Main Menu, choose “Movie” by using the / and M button, a “Movie Now
Playing” screen appears to use.
In the Movie Now Playing” screen, press the key to start playing.
Press the button to pause and to go back to the Movie Now Playing screen. Press it again,
the video will play continue.
b. To Play Previous or Next Video
Press the button to play the next movie file.
Press the button to play the previous movie file.
c. Use Fast-Forward or Fast-Backward
Press and hold the button to play fast-forward.
Press and hold the button to play fast-backward.
d. Adjust Volume Level
In movie playing, press the button to increase the volume level.
ATJ211D
10
In movie playing, press the button to decrease the volume level.
To preset the volume level at movie stop mode, in the Movie Now Playing screen press the
/ key to preset your desired volume level; a volume control screen appears to view. Press
the / M button to return to the Movie Now Playing.
For hearing protection; a beep warning will be heard from the earphone, or display warning
pop-up on TFT screen, every time you increase the volume level and reach the default setting level
which may exceed 85dB. Press the M button to accept the warning and enter into the volume
control to increase the level up to the maximum level.
10. Use Movie Submenu
You might need to select folders, delete movie files and set repeat for movie play. You can make
changes in the playing mode at the Movie Now playing screen. To do this:
In the “Movie Now Playing” screen, press the M button to enter the movie submenu.
a. Local Folder
In the movie submenu screen, choose the “Local Folder”, a file list menu appears, and then
select a folder and / or choose a desired movie file to play by using the / and M
button.
It will go back to the music now playing screen once a music file is selected. Then press the
button to play.
b. Delete File
In the movie submenu screen, choose “Delete file”; a file list menu appears, and then choose
which movie file that you want to delete by using the / buttons.
Once a file is selected, press the M button and choose “Yes” to confirm or “No” to cancel.
c. Delete All
In the movie submenu screen, choose “Delete all”; then select “Yes / No” by using the /
button.
One “YES” or “NO” appears; then press the M button to confirm.
All movie files will be deleted once YES is selected and confirmed; a “Deleting” screen appears
for a while and the deleting process is in progress, then an “Empty disk!” message will be
shown on the screen for a few seconds.
d. Repeat
In movie submenu, choose “Repeat”, then choose “Normal / Repeat one / Repeat all /
Repeat folder / Repeat all / Random Folder” as you desired by using / and M
buttons.
d. Exit
Select Exit to back to music now playing screen.
11. Convert Video files into AMV
This tool can be used to transform those video files into AMV files on the computer before you
upload them to your player.
To install this video convert tool to your computer, click “Utilities > video conversion
software” in the provided CD. (or stored in your Player)
ATJ211D
11
Select “Setup” to start the install program, the software will automatically be installed to your
computer.
After the installation is done, open the AMV Video converter on the PC.
Noted: This program is used to convert video files into the AMV format, currently only the AMV
format is supported.
Run the “AMV Video Converter”, click to choose the folder where to save the AMV files,
and then click to select the folder where the original files are. The original file will be
shown in the file window once selected.
Select with highlight the unprocessed AMV files in the file window, the icon will be
highlighted into . And then click the icon and a dialog box will be shown.
Choosing pixels of AMV to “160x120” and Frames per second to “middle”, then click OK to
confirm.
Click to start converting.
ATJ211D
12
After conversion, the AMV files will play automatically for preview.
And now the converted AMV file is ready to transfer, you can simply copy and place those
converted AMV files to the media player.
Note: Only pixels in 160x120 or 320x240 can be supported.
12. Use Record Menu
You can use the player as a Voice Recorder and record voice memos using the built-in microphone.
a. To Start Recording Voice Memo
From the main menu, choose “Record” by using the / and M buttons, a “Now
Recording” screen appears to use.
“Now Recording” Screen
b. To Start / Pause Recording
Press the button to start the recording and the recording time is running.
Press the button to pause the recording and the recording time will stop and be flashing.
Press it again and the recording and time will be continued.
c. To Save and Stop Recording File
Press and hold the M button, the recorded file will be saved into the memory.
13. Use Record Submenu (in Stop Mode)
You might need to change the folder locations which want to store the record file and / or change
the record quality for better compression values.
In the Now Recording screen, in the stop mode, press the M button, a “Record Sub-menu
appears to use.
ATJ211D
13
a. Local folder
In the record submenu, choose the “Local folder” and then choose the folder name where
you want to save the record file by using the / and M buttons.
Once the folder name is selected, press and hold the M button, then the folder location is
changed and you return to the Now Recording screen.
Now you can see the folder name is changed at the Record Folder icon in the “Now
Recording” screen.
b. Record Type
In the record submenu, choose “Record type”, then choose “32K BPS / 64K BPS / 128K BPS /
256K BPS” values as you desire by using the / and M buttons.
c. Exit
Select Exit to go back to the now recording screen.
14. Use Pedometer
From the main menu choose “Pedometer” by using the / and M buttons. A
pedometer menu appears to use.
Pedometer Menu
a. Setup your pedometer before start
Before you start to use the pedometer function, you need to input your personal information
and calibrate the player’s pedometer sensor to personalize it.
From the pedometer menu, choose “Pedometer”, then choose “Setting” by using the /
and M buttons. A sub list menu appears.
Choose “Women / Man”, then choose stride “Walking / Jogging / Running”, a level bar with
numbers appear to choose from. Input your average stride length, for example 80 (cm); refer
to “Stride Length Measurement” as illustrated below, by using the / and M buttons.
Once the average stride length is set, it will return to the pedometer menu. (Adjustment range
can be set from 10 – 200 (cm) by increase / decrease 1 cm step)
Choose “Setting” to change the setting again if you want.
Choose “Exit” to return to the main menu.
b. Stride length measurement
Walk / Jog / Run 10 steps with your normal stride as illustrated below.
ATJ211D
14
Measure the distance from START to END in centimeters (cm). Then calculate your stride
length by dividing the total distance by 10. Example:
Total distance = 800 cm
800 cm ÷ 10 steps = 80 cm
c. Start / Exit pedometer counts & Look Up record
Choose “Start” to enter and start the pedometer’s counting function when settings are
completed, the pedometer’s counting display appears and time starts running, from
“00:00:00”. At the same time the pedometer’s sensor is starting to count your move. Now you
can start the walk.
Those wanted information; such as: Steps, Distance, Calorie burned and Speed, are shown on
the pedometer’s counting display screen.
Pedometer Counts Display
To Exit the pedometer’s counting function and Save the personal counts record, press the M
button, a confirm screen appears, then choose “Yes” to confirm and the screen will return to
the main menu. The record is saved. Or, choose “No” to cancel and continue the pedometer
counting.
In the pedometer menu, choose “Look up” to view the personal counts record. The player is
allowed to store a maximum of 2 personal counts named “Record 1 / Record 2”. Moreover,
the new records will overwrite the old Record 1 and Record 2. Press the M button to exit from
the personal counting record display and return to the main menu.
Personal Counts Record
ATJ211D
15
d. Play Music in Pedometer Function
From the pedometer menu, choose “Local folder / Card folder” > by using the /
and M buttons. A list menu with folders / files appears to choose from.
Choose a folder and file, which music as the first music to play, when you start to play a song
in the pedometer’s counting display mode. The screen will return to the pedometer menu.
Choose “Start” to enter the pedometer counting display mode. Press the button to start
playing music with the pedometer’s counting function if you wish, and you can pause / stop by
pressing the button again. Or, just only using the pedometer’s counting function.
e. Music controls in pedometer (same as music mode)
In pedometer’s counting mode:
Press the button to start the play. Press it again to pause.
Press the button to play the next music.
Press the button to play the previous music.
Press and hold the button to use fast-forward.
Press and hold the button to use fast-backward.
In music playing, press the button to increase the volume level, a change volume control
screen appears.
In music playing, press the button to decrease the volume level, a change volume control
screen appears.
Press the button to return to the music now playing screen.
Note: In the pedometer mode, some music settings are defaulted and cannot be changed. Such as
Repeat All (Cycling), In Order Play.
f. Attaching the player for pedometer
Place the unit on Armband
Put the unit on your waistband and adjust it to a comfortable
position.
ATJ211D
16
Place the unit in your pocket
Do not place the unit in the back pocket of your pants, to
prevent sitting on it.
Close the zipper / button of your pocket (if available) to
prevent the unit from dropping.
Place the unit in your bag
Place the unit in a secure section or partition of your bag.
Make sure the unit is placed horizontally or vertically in a
pocket in the bag.
Hanging the unit from your neck
Attach a secure lanyard or string to the unit. (not provided)
Place the lanyard around your neck and hang the unit as
illustrated.
NOTE: Make sure the lanyard / string is correctly sized to easily
remove the unit from around your neck. If used hanging around
neck, the lanyard / string can cause strangulation. Do not place
the unit with lanyard / string around a child’s neck.
g. The unit may not count steps correctly in the following conditions:
The unit is not positioned correctly.
When the front of the main unit is placed in the angle of less
than 60° or horizontally to the ground.
NOTE: The unit can count steps even if it is slanted or placed
upside-down, or if the main unit is perpendicular to the ground.
The unit moves loosely.
When the unit is loose or flat in your pocket or bag (not in a
horizontal or vertical position).
When the unit swings from your belt, the top of your pants or
a bag.
ATJ211D
17
Up and down movement.
Standing up and/or sitting down movement.
Playing sports other than walking.
Ascending or descending movement at stairs or in a steep
slope.
Walking at an inconsistent stride.
When you shuffle or wear sandals.
Starting and stopping or other forms of inconsistent walking.
Walking extremely slowly.
Vibrations from a moving vehicle.
Such as riding a bicycle, automobile, train or bus.
15. Use Voice Menu
For playback and managing the recorded voice memos file.
From the main menu, choose the “Voice” menu by using the / and M buttons, a
“Voice Now Playing” screen appears.
“Voice Now Playing” Screen
a. To Play and Pause Recorded Voice Memos
In the Voice Now Playing screen, press the button to start playing the recorded file.
Press the button to pause the playing file.
b. To Play the Previous or Next File
Press the button to play the next file.
Press the button to play the previous file.
c. To Fast-Forward or Fast-Backward
Press and hold the buttons to use fast-forward.
Press and hold the button to use fast-backward.
d. Adjust volume level
In music playing, press the button to increase the volume level, a change volume control
screen appears.
In music playing, press the button to decrease the volume level, a change volume control
screen appears.
Wait for 6 – 8 seconds or press the button to return to the music now playing screen.
ATJ211D
18
16. Use Voice Submenu in Stop Mode
You might need to change some settings as you desire for playing Voice file, you can make changes
in the playing mode at the Voice Now Playing screen.
a. Local Folder
In the Voice Now Playing screen, press the button to pause / stop the playing file, if in
playing mode, then press the M button to call up the voice submenu.
In the Voice submenu screen, choose the “Local folder”; a list menu appears, and then select
a folder and / or choose a voice file by using the / and M button.
It will go back to the music now playing screen once a music file is selected. Then press the
button to play.
b. Delete File
In the voice submenu screen, choose “Delete file”; a list menu appears, and then choose
which voice file that you want to delete by using the / and M buttons.
Once a file is selected, press the M button and choose Yes to confirm or No to cancel.
c. Delete All
In the voice sub-menu screen, choose “Delete all”; then select “Yes / No” by using the /
button.
Once “YES” or “NO” appears, press the M button to confirm.
All music files will be deleted once YES is selected and confirmed, a “Deleting” screen appears
for a while and the deleting process is in progress, then an “Empty disk!” message will be
shown on the screen for a few seconds.
d. Exit
Select Exit to go back to the music now playing screen.
17. Use Voice Sub-menu in Playing Mode
You might need to do some changes for music playing, such as repeat, EQ settings for music files…
etc. To change settings:
a. Repeat
In the voice playing mode, press the M button. A Music Sub-menu appears, then choose
“Repeat”, then choose “Normal / Repeat one / Repeat all / Repeat folder / Random all /
Random folder” as you desire by using the / and M buttons.
b. Exit
Select Exit to go back to the music now playing screen.
Note: Press and hold the M button will go back to Main Menu directly.
18. Use Photo Browse
You can use the player as picture / photo viewer:
To browse a picture / photo file, choose “Photo” from the main menu using the /
and M button; a list menu appears.
Choose a file by using the / button, and then press the button to play.
Press the button to stop and to go back to the list menu for other files selection.
ATJ211D
19
To change the previous / next photo, press the / button.
Press and hold the M button to go back to the main menu.
19. Use Photo Submenu in List Screen
You might need to change some settings for photo browse. To change settings:
a. Local Folder
In the list menu, press the M button to call up the photo submenu.
In the photo submenu, choose “Local folder”; a list menu appear, and then choose folder and
file to browse by using the / and M button.
Once a photo file is selected, press the button to play.
b. Playback Set
In the photo submenu, choose “Playback set” and then choose “Manual play”. However, you
need to use the / button to browse the next / previous photo in the photo playing
mode when Manual Play is selected.
Choose “Auto play”; a setting menu appears, then choose “2 / 3 / 4 / 5 / 5 / 6 / 7 / 8 / 9 / 10
seconds)” as you desire by using the / and M buttons. The slide show function is
activated as your selected time gap to play the photo files one by one automatically.
c. Delete file
In the photo submenu, choose “Delete file”; a list menu appears, and then choose which
photo file you want to delete by using the / button.
Once a file is selected, press the M button and choose Yes to confirm or No to cancel.
d. Delete All
In the photo submenu, choose “Delete all”; then select “Yes / No” by using the /
button.
Once “YES” or “NO” appears press the M button to confirm.
All photo files will be deleted once YES is selected and confirmed; a “Deleting” screen appears
for a while and the deleting process is in progress; then an “Empty disk!” message will be
shown on the screen for a few seconds.
e. Exit
Select Exit to go back to the photo browse list menu screen.
20. Use Game Menu
There is a game named “Snake”. Control the snake move up, down, left and right to eat the food
(dot) which will exist somewhere on the TFT screen. The snake’s body will get longer every time he
eats something, but don’t let the snake hit the walls and hit the snake’s body.
To play the game, from Main menu, choose “Game” menu, then choose a game to play.
Control KEY instruction; Press: : up, : down, : left, : right, : Pause.
Press and hold the M button to exit the game.
21. Use eBook Menu
You can use the player as a text reader with supported file format (.TXT).
a. To open an eBook
From the main menu, choose “eBook” by using the / and M buttons. A list menu
ATJ211D
20
appears.
Choose a file which you want to read by using the / button, and then press the
button to play.
Press the button to change to the next page,
Press the button to go back to the previous page,
Back to list menu screen, press the button.
Go back to main menu, press and hold the M button
22. Us eBook Submenu in list menu screen
You might need to change some settings for eBook reading. To change settings:
a. Local Folder
In the eBook list menu screen, press the M button to call up the eBook Submenu.
In the eBook Submenu, choose “Local folder”; a list menu appear, and then choose a folder
and file by using the / button.
Once a file is selected, press the M button and then the button to read.
b. Playback Set
In the eBook Submenu, choose “Playback set” and then choose “Manual play”. You need to
use the / button to change to the next / previous page for reading when Manual
Play is selected. Or,
Choose “Auto play”; a setting menu appears, then choose “1 / 2 / 3 / 4 / 5 / 5 / 6 / 7 / 8 / 9 /
10 second(s)” as you desire by using the / and M buttons. The Page Flip function is
activated as your selected time gap to play.
c. Delete file
In the eBook Submenu, choose “Delete file”; a list menu appears, and then choose which
eBook file that you want to delete by using the / button.
Once a file is selected, press the M button and choose Yes to confirm or No to cancel.
d. Delete All
In the eBook Submenu, choose “Delete all”; then select “Yes / No” by using the /
button.
Once “YES” or “NO” appears press the M button to confirm.
All eBook files will be deleted once YES is selected and confirmed, a “Deleting” screen appears
for a while and deleting process is in progress, then an “Empty disk!” message will be shown
on screen for a few seconds.
e. Exit
Select Exit to go back to the eBook list menu screen.
23. Us eBook Submenu in Playing Mode
You might need to add, select and delete some bookmarks when you are reading; to do this:
a. Bookmark Select
In the eBook playing mode, choose “Bookmark select” by using the / and M
button.
Choose a stored bookmark that you want to call and then press the M button to play.
Page is loading ...
Page is loading ...
Page is loading ...
/