Storage Options 53317 - DIY Home CCTV Kit Owner's manual

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE THE COVER.

NO USER SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of non-

insulated “dangerous voltage” within the product’s enclosure that

may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS UNIT TO RAIN OR MOISTURE

CAUTION:

TO PREVENT ELECTRIC SHOCK, ENSURE THE PLUG

IS FULLY INSERTED INTO A MAINS SOCKET

Page 3

IMPORTANT SAFEGUARD

All lead-free products offered by the company comply with the requirements of the European law of

the Restriction of Hazardous Substances (RoHS) directive, which means our manufacturing processes

and products are strictly “lead-free” and without the hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be

collected separately at the product’s end-of-life. This applies to your product and any peripherals

marked with this symbol. Do not dispose of these products as unsorted municipal waste. Contact

your local dealer for procedures for recycling this equipment.

DISCLAIMER

We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume any legal liability

or responsibility for the accuracy, completeness, or usefulness of this manual. The content of this manual is subject to change

without notice.

RECOMMENDATIONS

 AVOID DUSTY LOCATIONS:

 INSTALL IN VENTILATED SPACE:

 DO NOT EXPOSE TO MOISTURE:

 DO NOT DROP:

 DO NOT OPEN CHASSIS:

Excessive build-up of dust may cause the unit to fail.

Ensure adequate airflow around the DVR to prevent overheating.

Exposing the unit to water poses high risk of electric shock.

Doing so could damage internal components.

No user-serviceable parts inside.

TRADEMARK ACKNOWLEDGEMENTS

 Internet Explorer, Microsoft & Windows are registered trademarks of Microsoft Corporation.

 Apple, iPhone, iPad and iTunes are registered trademarks of Apple Computer, Inc.

DEFAULT PASS CODE INFORMATION

By default, pass codes are disabled on the system. You do not need to enter a pass code when accessing any menus. For

security purposes, it is highly recommended to enable pass codes via the Password Menu.

WARRANTY AND TECHNICAL SUPPORT

To help you make the most of this product you’ll find a host of information including full product manuals, FAQ, troubleshooting

guides and a support service if you have specific questions, available at our support website: www.storageoptions.com/support.

This product is also backed by a 12 month warranty in the unlikely event of something going wrong. More information and

warranty registration is available at www.storageoptions.com/warranty.

Support:

www.storageoptions.com/support/

Warranty:

www.storageoptions.com/warranty/

Page 4

TABLE OF CONTENTS

QUICK START GUIDE

6

1.1 – Basic Connectivity

1.2 – Wall Mounting A Camera

1.3 – Power Connection Diagram

6

7

8

OVERVIEW

9

2.1 – System Overview

2.2 – Environment Adaptability

2.3 – Recording Capacities

9

CONVENTIONS USED IN THIS MANUAL

10

PACKAGE CONTENTS

10

SYSTEM CONNECTION

11

5.1 – Connectivity Diagram

11

BASIC OPERATION

12

6.1 – Front Panel

6.2 – Rear Panel

6.3 – Remote Control

6.4 – Mouse Control

6.5 – Using The Sub Menu

6.6 – Power On / Off

6.7 – Pass Codes

6.8 – Format The Hard Disk Drive

6.9 – System Login

6.10 – Playback

6.11 – On-screen Playback Controls

12

13

14

15

16

17

BASIC MENU FUNCTIONS

18

7.1 – Main Menu

7.2 – Search

7.3 – File List

7.4 – Backup

7.5 – Record Mode

7.6 – Recording Schedule

7.7 – HDD Management

7.8 – Basic Setup

7.9 – Language

7.10 – Date / Time

7.11 – Daylight Saving Time

7.12 – Password

7.13 – User Permissions

7.14 – Display

7.15 – Live

7.16 – Video / Audio

7.17 – Volume Setup

18

19

20

21

22

24

25

26

27

28

29

30

31

Page 5

TABLE OF CONTENTS (CONTINUED)

ADVANCED MENU FUNCTIONS

32

8.1 – Advanced Setup

8.2 – Alarm

8.3 – E-Mail Setup

8.4 – System Info

8.5 – Motion Detection

8.6 – Mobile

8.7 – System

8.8 – Firmware Upgrade

8.9 – Parameter Export

8.10 – Parameter Import

8.11 – Pan Tilt Zoom (PTZ)

8.12 – Network

8.13 – DDNS

8.14 – UPnP

32

33

34

35

36

37

38

39

40

41

42

REMOTE SURVEILLANCE SOFTWARE

43

9.1 – Using Remote Surveillance

9.2 – Main Screen

9.3 – Live View

9.4 – Recording

9.5 – Sub Menu

9.6 – PTZ Control

9.7 – Screen Captures

9.8 – Playback

9.9 – Search

9.10 – Remote Backup

9.11 – Remote Setup

9.12 – Record

9.13 – Alarm Setting

9.14 – PTZ

9.15 – Network

9.16 – Setting

9.17 – Maintenance

9.18 – Host Info

44

45

46

47

48

49

50

51

52

53

SOFTWARE CD

54

REMOTE ACCESS

55

HARD DISK DRIVE INSTALLATION

56

TROUBLESHOOTING

57

PRODUCT SPECIFICATION

58

Page 6

QUICK START GUIDE

1.1 – BASIC CONNECTIVITY

To get started quickly with the Storage Options 2 Channel CCTV DVR, follow these instructions:

1. Connect a camera to the “Video In 1” socket.

2. Connect a computer monitor to the “VGA” socket.

AND / OR

Connect a television to the “Video Out” socket.

NOTE

You must select the correct input on your monitor / television to view the DVR system. Refer to its

manual for instructions on how to do this.

3. Connect the DVR and camera to a mains supply.

Refer to section “1.3 – Power Connection Diagram” (page 8) for more information.

4. The DVR will automatically switch on when connected to a mains socket. Alternatively, press the STANDBY

button on the remote control.

Refer to section “6.3 – Remote Control” (page 14) for more information.

5. Set the date and time.

Refer to section “7.10 – Date / Time” (page 27) for more information.

6. Format (prepare) the Hard Disk Drive (HDD).

Refer to section “7.7 – HDD Management” (page 25) for more information.

Page 7

1.2 – WALL MOUNTING A CAMERA

Each Storage Options camera is supplied with a mounting kit for attaching it to a wall. Before you affix the camera in

position, please ensure the cable is of adequate length to reach the DVR.

To mount the camera on a wall or ceiling, follow these instructions:

1. Ensure the surface you want to mount the camera on is solid and can support the weight.

2. Accurately mark on the wall the position of the holes to be drilled.

3. Drill to the correct depth in the wall, as indicated by the plugs.

4. Insert plugs into the drilled holes.

5. Secure the bracket to the wall using the provided screws.

To attach the camera to the bracket:

1. Screw it onto the exposed thread

2. Tighten the bolt to lock it in place.

To adjust the camera’s position, turn the bolt arm anti-clockwise to release the ball and socket configuration,

position the camera, then turn the bolt arm clockwise to re-tighten.

Page 8

1.3 – POWER CONNECTION DIAGRAM

This system is supplied a 1-5 power splitter cable, which allows you to connect the DVR and up to four cameras to a

single mains socket.

Connect power to the DVR and cameras as shown in this diagram:

BLUE = Camera mains connection

RED = DVR mains connection

YELLOW = Video connection

The 1-5 power splitter cable has one red and four black plugs.

 Connect the red cable to the DVR.

 Connect the black cables to the two included cameras.

Each Storage Options CCTV camera (sold separately) also comes with its own mains adapter. You can either plug

them into separate mains sockets, or into the two spare cables on the power splitter.

CAUTION

The 1-5 power splitter is designed for use ONLY with Storage Options cameras! DO NOT attempt to

connect other brands as this may present a risk of fire!

Page 9

OVERVIEW

2.1 – SYSTEM OVERVIEW

Installing this DIY Home CCTV Kit could be one of the best steps you ever take to secure your home or business

premises. As well as protecting against criminal activity and actively deterring criminals from targeting your property

and vehicles, it will bring additional peace of mind for you and your family.

Designed specifically for use and installation by those with no experience or prior knowledge of CCTV systems,

everything you need is contained in the box including a clear instruction manual. If you need additional help, our

UK-based support team is available for the price of a local rate phone call.

 Quick and easy to install – no expert help required

 View on your existing TV, monitor or smart phone

 Up to 50 days continuous recording

 Fully weatherproof cameras with night vision

 DIY Kit with all fixtures, a detailed manual and installation guide included

 Local-rate UK-based support line

2.2 – ENVIRONMENT ADAPTABILITY

For safety while using the DVR and to prolong the device’s useful life, please pay attention to the following details:

 Do not touch the DVR or mains adapter with a wet hand.

 Do not drop liquid on the DVR or mains adapter.

 Do not put any object on the DVR.

 Please use a soft, dry cloth to clean the DVR; do not use chemical cleaning fluids.

 The DVR will have voltage before start-up if the mains adapter is connected to a mains socket.

 Please unplug the mains adapter from its socket if the DVR is not going to be used for a prolonged period

of time.

2.3 – RECORDING CAPACITIES

This table shows the amount of recording time (in days*) of the DVR, depending on how many cameras are

connected:

NUMBER OF CAMERAS

1

2

3

4

500GB HDD

100

50

33

25

* All values are approximate. Actual results may vary according to recording conditions.

Page 10

CONVENTIONS USED IN THIS MANUAL

At various points in this manual you will see highlighted text. Please refer here for an explanation:

NOTE

Important notes are highlighted in blue.

TIP

Tips on best practice are highlighted in green.

CAUTION

Important cautions and warnings are highlighted in red.

Unless otherwise stated, all functionality described in this manual is performed using the USB mouse.

PACKAGE CONTENTS

Check the contents of your DVR against this checklist. If anything is missing or damaged, please do not use the

system, and inform your supplier as soon as possible.

DVR

Power 1-5 splitter cable

2x CCTV camera

Remote control

Mouse

Software CD

AV cable

Screws and plugs

Instruction manual

Page 11

SYSTEM CONNECTION

5.1 – CONNECTIVITY DIAGRAM

Refer to this diagram for the recommended method of connecting this CCTV system.

Refer to section “1.3 – Power Connection Diagram” (page 8) for more information on connecting to a mains socket.

Page 12

BASIC OPERATION

6.1 – FRONT PANEL

1. IR SENSOR: Receives infra-red signals from the remote control. Do not cover.

2. LED INDICATORS: Shows system status.

LABEL

COLOUR

DESCRIPTION

HDD

GREEN

Flashes to indicate HDD activity.

REC

GREEN

Indicates whether the DVR is currently recording.

NET

GREEN

Flashes to indicate network traffic.

ALM

RED

Indicates whether an alarm trigger has occurred.

POWER

RED

Indicates whether the DVR is currently powered on.

Page 13

6.2 – REAR PANEL

Refer to the diagram and table below for information on the DVR’s various connections.

REFERENCE

PHYSICAL CONNECTOR

DESCRIPTION

1

POWER input

DC 12V / 3A

2

VGA output

Connect to a monitor with VGA (D-Sub) input

3

RJ45

Connect to a computer network

4

USB ports

For USB flash drive (top) and mouse (bottom)

5

RS485

Connect to PTZ camera

6

Video output

Connect to a TV or monitor (BNC)

7

Audio output

Connect audio output (phono)

8

Audio input

Connect audio input (phono)

9

Video input

4x numbered video inputs for cameras (BNC)

To connect a camera via BNC:

1. Align the BNC connector with the notches on the BNC socket and

slide into place.

2. Rotate the BNC connector clockwise until it locks in place.

To disconnect a camera:

1. Apply pressure to the BNC connector, then rotate anti-clockwise.

2. Slide the BNC connector away from the socket.

Page 14

6.3 – REMOTE CONTROL

The remote control can be used for navigating system menus. When using the remote control, the OK key performs

the same functions as left-clicking the mouse.

To use the remote control with the DVR system:

1. Insert 2x AAA 1.5V alkaline batteries (not included) into the back of the remote control. Please ensure

correct orientation.

2. Refer to the below diagram for button functions:

REF

BUTTON

DESCRIPTION

1

STANDBY

Press to sleep / wake up the DVR

2

LOGIN / LOCK

If Security is enabled in the Setup menu,

press to open the user pass code login

screen

3

NUMBERS

In menus, press 0-9 to enter values

In live view, press 1-4 to view channels in

full-screen display mode

4

Press to switch between quad and split-

screen display modes

5

MENU

Opens the main menu

6

PTZ

Opens the Pan Tilt Zoom (PTZ) controls

7

EXIT

Press to close menu windows

8

NAVIGATION / OK

Use ↑, ↓, ←, → to highlight menu options

Use OK to confirm selections

9

+ / –

In menus, press to adjust values

10

RECORD

Press to start manual recording

11

STOP

Press to stop manual recording

12

EXTRA

N/A

13

PLAYBACK CONTROL

Controls for play, pause, stop, fast forward,

and skip forward

TIP

When using the remote control to enter password and camera titles, select the field using the navigation

buttons, press ENTER, and then press the number buttons. Press Menu to confirm.

Page 15

6.4 – MOUSE CONTROL

The mouse can be used for navigating system menus.

NOTE

Unless otherwise stated, all system functions described in this manual are achieved through mouse input.

To use a mouse with the DVR system:

 Connect the mouse to the lower USB port located on the rear panel (labelled with a mouse icon).

Left Button:

Click to select a menu option.

During live viewing, double-click on a channel to view it in full-screen.

Double-click the channel again to return to split-screen grid view.

Right Button:

Click to open the Sub Menu.

Scroll Wheel:

Forward – switch to VGA.

Backward – switch to CVBS.

6.5 – USING THE SUB MENU

When using the mouse, open the Sub Menu to access system options, including the Main Menu and PTZ control.

1. Right click anywhere on screen to open the Sub Menu.

2. To close the menu, left-click anywhere on screen (outside the menu).

MAIN MENU:

Opens the system menu

KEYLOCK:

Locks the front panel buttons

CHN SWITCH:

Select split-screen display type

VIDEO SEARCH:

Open the Search Menu to view previously recorded video

PTZ:

Opens the PTZ control menu

MUTE:

Mute audio on the system

MANUAL REC:

Start manual recording

STOP REC:

Stop manual recording

ROTATION:

Video rotation

START CRUISE:

Start cruise mode

STOP CRUISE:

Stop cruise mode

Page 16

6.6 – POWER ON / OFF

To power the system on, connect the power cable to the DC 12V port on the rear panel. At start-up, the DVR

performs a basic system check and runs an initial loading sequence. After a few moments, it will load a live display

view.

The system can also be put into standby mode. It will still receive power but will not record anything until brought

back into operation mode.

1. To put the system in standby, press and hold the power button on the remote control until the on-screen

prompt closes.

2. To wake the system from standby mode, press and hold the power button on the remote control until the

DVR displays “System Initializing” on screen. The system will begin powering up.

6.7 – PASS CODES

By default, pass codes are disabled on the system. You do not need to enter a pass code when accessing any menus.

For security purposes, it is highly recommended to enable pass codes via the Password Menu.

6.8 – FORMAT THE HARD DISK DRIVE

This DVR uses a Hard Disk Drive (HDD) to record and store video footage. You must format the HDD before it can be

used to record video.

Go to Main Menu  HDD HDD Format, to prepare the drive for use. Refer to section “7.7 – HDD Management”

(page 25) for instructions on how to do this. After formatting is complete, follow the on-screen prompts to restart

the system.

NOTE

If no HDD is installed, or the HDD is not formatted, a red “H” symbol will be displayed on screen.

6.9 – SYSTEM LOGIN

To open the main menu, press the MENU / EXIT button on the remote control. Alternatively right-click anywhere on

screen with the mouse to open the Sub Menu, then select MAIN MENU.

NOTE

If pass codes are enabled on the system, you need to select your Device ID and enter the 6-digit numerical

pass code to open the main menu.

Page 17

6.10 – PLAYBACK

The Search Menu can be used to view previously recorded footage.

To begin playback:

1. Right-click anywhere on screen and select VIDEO SEARCH from the sub menu.

NOTE

When the Search Menu is first opened, it displays the current month and date.

2. Click PLAY to begin playback of the last minute of recorded video (quick search).

OR

Under CHN select a specific channel or select ALL.

3. Under DATE, enter a date using the virtual keyboard (mouse only).

4. Click SEARCH. Alarm / motion detected events will appear as red. Normal recordings will appear as green.

5. Click a date in the month grid to search for video files.

6. Click a time block in the Hour Grid to view the video. Playback will begin.

7. Move the mouse to display the on-screen playback controls. You can also use the playback control buttons

on the remote control.

6.11 – ON-SCREEN PLAYBACK CONTROLS

To use on-screen playback controls:

1. Click the VCR-like controls to play, pause, fast forward, rewind, and

slow playback.

2. Drag the slider to adjust the volume (requires audio-capable

camera, not included). Select the box to mute audio.

3. Click X to quit playback and return to the Search menu.

Page 18

BASIC MENU FUNCTIONS

7.1 – MAIN MENU

The main menu displays options for controlling every feature of the DVR. See below for an explanation of each of

the options on the main menu.

 RECORD SEARCH: Search for previously recorded video on the system.

 RECORD: Configure recording options, set record modes, and enable / disable audio recording.

 HDD: Display HDD status and format the internal hard drive.

 BASIC: Set the system language, date & time, Device IDs and passwords, configure AV settings, etc.

 ADVANCED: View system info, configure alarm, motion detection, PTZ, mobile, network settings.

 EXIT: Closes the Main Menu.

Page 19

7.2 – SEARCH

Use this function to search for and play back previously recorded video on the DVR system. When the Search menu

is opened for the first time, it will display the current date and time.

To perform a quick search, simply open the SEARCH menu and click PLAY. The last 60 seconds of recorded playback

will begin.

To perform a date and time search:

1. Under CHN, select individual channels or select ALL.

2. Under DATE, enter a desired date using the virtual keyboard, then click SEARCH. The system will search for

any related recordings.

3. Under RECORD STATE, the system shows recorded events in a month grid and an hour grid. The selected

day of the month will be outlined in red.

GREEN = normal recording

RED = alarm recording (both alarm & motion events)

4. Select a date in the month grid to view recorded video files for that date in the hour grid.

5. During playback, use the onscreen controls or the playback buttons on the remote to control video

transport.

Page 20

7.3 – FILE LIST

Use the File List sub menu to see a detailed list of all the recorded video on your system. To open the file list:

1. From the Search menu, click SEARCH to find recorded video.

2. Select FILE LIST at the bottom of the menu. The File List menu will open.

3. Highlight the required file and select it to begin playback.

To use the File List:

1. Under TYPE, select NORMAL to view only normal recordings, ALARM to view triggered recordings (alarm and

motion detection), or ALL to view all videos.

2. Use the buttons on the right side of the panel to navigate the file list:

FIRST:

Jump to the first page of the list.

PRE:

Return to the previous page.

LAST:

Jump to the last page of the list.

ALL:

Select all files.

OTHER:

Invert current file selection.

BACKUP:

After selecting a file(s), click BACKUP to begin copying the data to a USB flash drive

(not included).

EXIT:

Exit the File List menu.

Page is loading ...

Storage Options 53317 - DIY Home CCTV Kit Owner's manual

This manual is also suitable for

Storage Options 53317 - DIY Home CCTV Kit Owner's manual

Related papers

Other documents