Fax
(858) 578-7676
(858) 578-9558
Customer Service
(800) 548-5438
RECORD SERIAL NUMBER HERE
MACHINE CODE
Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNER'S MANUAL
A04
V-EXPRESS
MULTI-FUNCTION GYM
02
04
52
53
54
55
57
61
62
64
66
67
68
69
70
71
EXERCISE LOG......................................................................
OWNER'S MANUAL
PAGE 01
V-EXPRESS ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
ACCESSORIES/MISC............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
WEIGHT RATIOS....................................................................
CONTENTS
OWNER'S MANUAL
PAGE 02
V-EXPRESS ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER'S MANUAL
PAGE 03
V-EXPRESS ASSEMBLY
*
SHOWN WITH OPTIONAL WEIGHT SHIELDS.
FOR DETAILS, CONTACT YOUR DEALER.
OWNER'S MANUAL
PAGE 04
V-EXPRESS ASSEMBLY
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
FRAME ASSEMBLY
PAGE 05
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
117
29
95
109
15
32
95
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 06
108
95
29
95
117
NOTE:
- WRENCH TIGHTEN HARDWARE.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 07
V-EXPRESS ASSEMBLY
90
59
95
113
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 08
59
88
86
53
80
IF OPTIONAL 200 LB. WEIGHT STACK IS
PURCHASED, REMOVE AND DISCARD ALL
STAND-OFFS (80) AND ASSEMBLY WEIGHT
STACK WITH 5 MORE WEIGHT PLATES, AS
SHOWN TO THE RIGHT.
59
88
86
53
**OPTIONAL 200 LB. WEIGHT STACK**
CONSULT YOUR DEALER
FOR DETAILS
NOTE:
- HAND TIGHTEN HARDWARE.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 09
V-EXPRESS ASSEMBLY
34
32
72
95
72
105
95
117
WARNING!
BE SURE TO HAVE ONE PERSON FULLY SUPPORT UPRIGHT (34) WHILE THE
OTHER ALIGNS AND FASTENS HARDWARE. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
33
70
113
117
59
105
95
95
95
90
34
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 10
OPTION ONLY, DISCARD CABLE ANCHOR
PLATE (18).
NOTE:
- HAND TIGHTEN HARDWARE.
FOR INSTALLATION OF V LEG PRESS
FRAME ASSEMBLY
PAGE 11
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
32
*
117
*
parts at this time.
105
95
18
95
IMPORTANT -
If you are installing a V Leg Press option
refer to the V Leg Press owner's manual
and assemble the V Leg Press frame
31
102
94
94
116
16
32
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (102) THEN
LOOSEN NUT JUST ENOUGH FOR (16) TO
PIVOT FREELY.
- WRENCH TIGHTEN ALL PREVIOUSLY HAND
TIGHTENED HARDWARE.
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 12
*I MPORTANT*
NOW THAT THE V-EXPRESS FRAME IS COMPLETELY ASSEMBLED TAKE TIME TO
ASSURE THAT YOUR UNIT IS ASSEMBLED SQUARE AND PERPENDICULAR. USE A LEVEL
TO CHECK THAT THE GUIDE RODS ARE PERPENDICULAR IN BOTH DIRECTIONS.
IF NOT, IT WILL BE NECESSARY TO LOOSEN SOME FRAME HARDWARE TO RE-ALIGN
THE FRAME AND RETIGHTEN BOLTS.
NOTE:
- WRENCH TIGHTEN HARDWARE.
FRAME ASSEMBLY
V-EXPRESS ASSEMBLY
OWNER'S MANUAL
PAGE 13
101
94
94
11
66
33
116
8273
NOTE:
WHEN ADJUSTING CABLE FOR
PROPER TENSION, INSURE THAT
BOTH PLATES (73) ARE RESTING
UNDER THE BUMPER STOP (82)
AS SHOWN.
FRAME ASSEMBLY
CABLING PROFILE VIEW
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 14
4
GUARD RODS AS SHOWN.
BETWEEN THE PULLEYS AND
NOTE:
BE SURE CABLE RUNS
105
95
33
12
95
117
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 15
V-EXPRESS ASSEMBLY
4
146" 3708
105
95
51
33
95
117
4
GUARD ROD
BE SURE TO POSITION
CABLE (4) BETWEEN
PULLEY (51) AND
GUARD ROD AS SHOWN
PROPERLY INSTALLED VIEW
51
4
FRAME ASSEMBLY
NOTE:
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- WRENCH TIGHTEN HARDWARE.
- WRENCH TIGHTEN HAND TIGHTENED
HARDWARE FROM PREVIOUS STEP.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 16
105
64
64
117
49
33
NOTE:
IT MAY BE NECESSARY
TO LOOSEN GUIDE ROD
FASTENERS (103) TO
PROPERLY INSTALL
SPACER (64). ONCE
SPACER IS INSTALLED,
RE-TIGHTEN GUIDE ROD
FASTENERS.
PROPERLY INSTALLED VIEW
BE SURE TO POSITION
CABLE (4) BETWEEN
PULLEY (49) AND
GUARD ROD AS SHOWN
GUARD ROD
4
49
FRAME ASSEMBLY
NOTE:
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
PAGE 17
V-EXPRESS ASSEMBLY
11
49
4
PROPERLY INSTALLED VIEW
BE SURE TO POSITION
CABLE (4) AROUND
PULLEY AS SHOWN,
ENSURING THAT THE
STOPPER PLATE OF
HANGER (11) DOES NOT
INTERFERE WITH CABLE
ROUTE.
NOTE:
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
OWNER'S MANUAL
V-EXPRESS ASSEMBLY
PAGE 18
110
63
4
49
11
63
117
117
52
107
93
93
34
4
FRAME ASSEMBLY
NOTE:
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
V-EXPRESS ASSEMBLY
OWNER'S MANUAL
PAGE 19
52
PROPERLY INSTALLED VIEW
4
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
