Florida Pneumatic FPX-300 User manual

Type
User manual
MODEL: FPX-300
Die Grinder
BY FLORIDA PNEUMATIC
SPECIFICATIONS
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 1/4” NPT American Thread. Line pressure should be increased to compensate for
unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and ttings should have the same inside dimensions.
Air Supply
Model
Free Speed
(RPM)
Avg Air
Consumption
Noise level
d(B)A
Weight
(lbs)
Height
(in)
Length
(in)
Anvil size
(in)
Collets
size (in)
Air
inlet
Rec. Hose
Size (in)
FPX-300 25,000 4 94 0.83 1.65 5.9 NA 1/4"
1/4" NPT
3/8" ID
Important Warnings - Die Grinders
1. Only use mounted grinding stones or mounted carbide burrs that meet ANSI standards, ISO standards or both.
2. Never adjust the die grinder, adjust the collets or change the mounted stones or mounted burrs unless the air supply and air hose is
disconnected from the die grinder.
3. Only personnel trained in the correct methods to adjust collets and change mounted stones and mounted burrs should conduct these
operations.
4. Always ensure that you are aware of the direction of the sparks being created by the grinding operation and ensure that the sparks are
not directed toward the operator or other persons in the area.
5.
6. Only use mounted stones or carbide burrs that have the correct spindle diameter that matches the original collet size provided by the die
grinder manufacturer.
7. Particular care must be taken not to use metric size mounted stones and mounted burrs with die grinders that have imperial size collets,
or use imperial mounted stones and mounted burrs with die grinders that have metric collets.
MODEL: FPX-300
Die Grinder
Exploded View & Parts List
BY FLORIDA PNEUMATIC
32
31
30
29
28 27
21
25
03
02
01
23
24
22
20
19
12
13
14
16
15
18
35
36
26
26
17
04
10
08
09
07
11
06
05
34
33
FLORIDA PNEUMATIC MANUFACTURING CORPORATION
851 JUPITER PARK LANE | JUPITER, FL 33458
800-327-9403
www.florida-pneumatic.com
Florida Pneumatic Manufacturing Corporation warrants its tools to be free from
defects in materials and workmanship for a period of one year. Tools thought to be
defective should be returned to the factory, or an authorized
service center, transportation charges prepaid, for examination and
consequent repair or replacement. This warranty does not cover
damage to tools arising from alteration, abuse, or use for other
than their intended purpose and does not cover any repairs or
replacement made by anyone other than Florida Pneumatic
Manufacturing Corporation or its authorized repair stations.
The duration of the Warranty and any other Warranty including,
but not limited to, any implied Warranty of merchantability is expressly limited to one
year, beginning from the date of the delivery to the original user. The obligation of
Florida Pneumatic Manufacturing Corporation under any Warranty, express or implied,
is limited solely to the repair or replacement at its factory or authorized repair station of
any part which shall prove defective.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Florida Pneumatic FPX-300 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI