Machine configuration manual
Vibratory plate
DPU 130
03.2011
0217734en / 003
Manufacturer
Wacker Neuson SE
Preußenstraße 41
80809 München
www.wackerneuson.com
Tel.: +49-(0)89-354 02-0
Fax: +49-(0)89-354 02-390
Translation of the original operator's manual in German
DPU 130
Machine configuration manual 3
1 Foreword .................................................................................................................... 4
2 Introduction ............................................................................................................... 5
2.1 Means of representation for this operator's manual....................................................... 5
2.2 Wacker Neuson representative...................................................................................... 6
3 Using the configuration menu ................................................................................. 7
3.1 Opening the configuration menu and changing settings................................................ 8
3.2 Changing from numerical code display to language display........................................ 16
4 Troubleshooting ......................................................................................................18
5 PIN data .................................................................................................................... 19
1 Foreword DPU 130
4 Machine configuration manual
1 Foreword
Purpose of this manual
This manual describes the possible settings and the use of the configuration
menu on the machine's display screen. This manual also contains the factory-set
PIN data of your machine.
This manual is only intended for the operator of the machine, not for the user.
Store this manual where it will be safe from unauthorized access.
Follow operator's manual
This manual is a supplement to the operator's manual, and contains only notes
on the use of the configuration menu.
Also observe the information contained in the operating instructions of the
machine.
Legal notices
All rights reserved, especially reproduction and distribution rights.
Copyright 2011 Wacker Neuson SE
No part of this manual may be reproduced, processed, copied or distributed by
any means without the expressed written permission of Wacker Neuson.
Any type of reproduction, distribution or storage on data media of any type and
form not authorized by Wacker Neuson represents an infringement of copyright
and will be prosecuted.
2 Introduction
Machine configuration manual 5
2 Introduction
2.1 Means of representation for this operator's manual
Warning symbols
This operator's manual contains safety information of the categories:
DANGER, WARNING, CAUTION, NOTICE.
They should be followed to prevent danger to life and limb of the operator or
damage to equipment and exclude improper service.
Notes
Note: Complementary information will be displayed here.
DANGER
This warning notice indicates immediate hazards that result in serious injury or
even death.
f Danger can be avoided by the following the actions mentioned.
WARNING
This warning notice indicates possible hazards that can result in serious injury
or even death.
f Danger can be avoided by the following the actions mentioned.
CAUTION
This warning notice indicates possible hazards that can result in minor injury.
f Danger can be avoided by the following the actions mentioned.
NOTICE
This warning notice indicates possible hazards that can result in material
damage.
f Danger can be avoided by the following the actions mentioned.
2 Introduction
6 Machine configuration manual
Instructions
f This symbol indicates there is something for you to do.
1. Numbered instructions indicate that you have to carry out something in a defined
sequence.
This symbol is used for lists.
2.2 Wacker Neuson representative
Depending on your country, your Wacker Neuson representative is your Wacker
Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.
You can find the addresses in the Internet at www.wackerneuson.com.
The address of the manufacturer is located at the beginning of this operator's
manual.
DPU 130 3 Using the configuration menu
Machine configuration manual 7
3 Using the configuration menu
The machine has a machine configuration system, with which you can adjust
certain of the machine's settings to meet your requirements:
Settings options in the configuration menu
In the configuration menu on the display screen, you can adjust the following
machine settings:
Change setup PIN.
Modify/activate/deactivate machine PIN.
Set machine turn-off time.
Select display language (German, English, French, Spanish, numerical code
display).
Set how the machine reacts to overload (overload sensor).
Operator's controls
Use the ON/OFF switch on the machine to switch between the menu items of the
configuration menu.
The levers on the remote control can be used to change the settings.
Item Designation
1 Configuration menu
2 Remote control
3 Using the configuration menu DPU 130
8 Machine configuration manual
3.1 Opening the configuration menu and changing settings
Opening the configuration menu
Note: Access to the configuration menu is secured by the setup PIN.
1. Activate machine.
2. Turn on remote control.
3. Hold the ON/OFF switch on the machine at the same time as the Stand
vibration button on the remote control for at least 3 seconds.
The following text appears on the display:
CAUTION
Unintentional changing of settings.
If you select Setup Exit, the changed settings are always saved.
f If you accidentally changed settings and you do not want to save them,
switch off the machine with the emergency stop switch.
Item Designation Item Designation
1 ON/OFF switch 3 Right control lever
2 Left control lever 4 Stand vibration button
Wait...
DPU 130 3 Using the configuration menu
Machine configuration manual 9
After approx. 2 seconds the following text appears on the display:
4. If the following text appears on the display, enter the setup PIN using the
remote control and then press the ON/OFF switch on the machine.
Push the left control lever on the remote control forward or backward to select
the position.
Push the right control lever on the remote control forward or backward to
select the number.
Note: If you entered the setup PIN incorrectly, an error message will appear
on the display.
If it does, press the ON/OFF switch to be able to reenter the PIN.
5. If, having entered the setup PIN correctly, the following text appears on the
display, press the ON/OFF switch on the machine.
You are now in the configuration menu.
You can change settings using the control levers of the remote control or just run
through the configuration menu using the ON/OFF switch on the machine, to
check the settings.
Setup-PIN
Enter PIN
Enter PIN
0000
Setup
Continue with ON
3 Using the configuration menu DPU 130
10 Machine configuration manual
Changing the setup PIN
The setup PIN secures access to the configuration menu.
You can change the factory default setup PIN.
Note: Never deactivate the setup PIN because otherwise the configuration
menu is not protected against unauthorized changes.
1. Press the ON/OFF switch on the machine until the following text appears on
the display:
2. After approx. 2 seconds the following text appears on the display and you can
change the setup PIN:
Push the left control lever on the remote control forward or backward to select
the position.
Push the right control lever on the remote control forward or backward to
select the number.
Value
Setup PIN
8946 Factory default setting
0000 Setup PIN deactivated
0001
thru
9999
Possible setup PIN combinations
Setup
Setup-PIN
Setup-PIN
8946
DPU 130 3 Using the configuration menu
Machine configuration manual 11
Changing the PIN
You can set a PIN that will protect the machine from unauthorized operation.
After activating the machine, the user must enter the PIN with the remote control.
1. Press the ON/OFF switch on the machine until the following text appears on
the display:
2. After approx. 2 seconds the following text appears on the display and you can
change the PIN:
Push the left control lever on the remote control forward or backward to select
the position.
Push the right control lever on the remote control forward or backward to
select the number.
Value
PIN
0000 PIN entry deactivated (factory default setting)
0001
thru
9999
Possible PIN combinations
Setup
PIN
PIN
2000
3 Using the configuration menu DPU 130
12 Machine configuration manual
Setting the turn-off time
You can select the amount of time after which the machine automatically
deactivates if it does not receive any more commands from the remote control.
1. Press the ON/OFF switch on the machine until the following text appears on
the display:
2. After approx. 2 seconds the following text appears on the display and you can
change the turn-off time:
Push the right control lever on the remote control forward or backward to
select the number.
Value Turn-off time
1 1 h (factory default setting)
22h
33h
44h
Setup
Turn-off time
Turn-off time
1
DPU 130 3 Using the configuration menu
Machine configuration manual 13
Setting the language
You can choose the language in which information will be shown on the display
screen.
1. Press the ON/OFF switch on the machine until the following text appears on
the display screen:
2. After approx. 2 seconds the following text appears on the display and you can
set the language:
Push the right control lever on the remote control forward or backward to
select the number.
Value
Language
0 German (factory default setting for EU machines)
1 English (factory default setting for US machines)
2 French
3 Spanish
4 Numerical code display (no language)
Language-neutral display solely using numerical code. Use
this setting if the user does not understand the languages
listed above.
The meaning of the numerical codes is given in the appendix
of the operator's manual.
Setup
Select language
Select language
1
3 Using the configuration menu DPU 130
14 Machine configuration manual
Setting the overload sensor
The machine's overload sensor detects when you are operating the machine on
hard ground that cannot be further compressed. You can determine how the
machine should react to overload in order to protect it from damage.
1. Press the ON/OFF switch on the machine until the following text appears on
the display:
2. After approx. 2 seconds the following text appears on the display screen and
you can set how the machine is to react in the event of overload.
Push the right control lever on the remote control forward or backward to
select the number.
Value Overload sensor
0 (Factory default setting)
The receiver units briefly flash red.
After more than 10 seconds of overload, an entry is made in
the error memory (error code 13).
The machine can be operated despite overload.
1 The receiver units briefly flash red.
No entry is made in the machine's error memory.
If overloaded, the machine immediately reduces compaction
performance.
2 The receiver units briefly flash red.
After more than 10 seconds of overload, an entry is made in
the error memory (error code 12).
If overloaded for longer than 10 seconds, the engine is
switched off.
3 The receiver units briefly flash red.
No entry is made in the machine's error memory.
If overloaded, the machine immediately switches to slow
operation (engine in idling mode), and reduces compaction
performance.
Setup
Overload sensor
Overload sensor
0
DPU 130 3 Using the configuration menu
Machine configuration manual 15
Exiting the configuration menu and saving your settings
1. Press the ON/OFF switch on the machine until the following text appears on
the display screen:
After approx. 2 seconds the changed settings are saved and the configuration
menu is exited.
Note:
If you are uncertain and wish to check the changed settings again, before the
2 seconds have elapsed, press the ON/OFF switch on the machine to run
through the configuration menu again.
2. Deactivate the machine.
Note:
For the changed settings to become effective, the machine must be deactivated
once and then reactivated.
Setup
Exit
3 Using the configuration menu DPU 130
16 Machine configuration manual
3.2 Changing from numerical code display to language display
Note: The meaning of the numerical codes is given in the appendix of the
operator's manual.
The following steps are necessary to switch from numerical code display back to
language display:
1. Activate machine.
2. Turn on remote control.
3. Hold the ON/OFF switch on the machine at the same time as the Stand
vibration button on the remote control for at least 3 seconds.
4. If the following text appears on the display screen, enter the setup PIN using
the remote control and then confirm with the ON/OFF switch:
Push the left control lever on the remote control forward or backward to select
the position.
Push the right control lever on the remote control forward or backward to
select the number.
5. Press the ON/OFF switch on the machine until the following text appears on
the display screen:
6. After approx. 2 seconds the following text appears on the display and you can
set the language:
Push the right control lever on the remote control forward or backward to
select the number.
32
0000
3
20
20
4
DPU 130 3 Using the configuration menu
Machine configuration manual 17
7. Press the ON/OFF switch on the machine until the following text appears on
the display:
When the selected language appears on the display screen, the setting is
complete.
Value
Language
0 German (factory default setting for EU machines)
1 English (factory default setting for US machines)
2 French
3 Spanish
4 Numerical code display (no language)
Language-neutral display solely using numerical code. Use
this setting if the user does not understand the languages
listed above.
The meaning of the numerical codes is given in the appendix
of the operator's manual.
3
40
4 Troubleshooting DPU 130
18 Machine configuration manual
4 Troubleshooting
Potential faults, their causes and remedies can be found in the following table.
Malfunction Cause Remedy
Configuration menu cannot be
called.
Machine has not been
activated.
Activate machine and wait until
the display screen shows the
hours of operation.
The ON/OFF switch on the
machine and on the remote
control was not pressed down
for long enough.
Press and hold down the ON/
OFF switch on the machine at
the same time as the Stand
vibration button on the remote
control for at least 3 seconds.
ON/OFF switch on machine
was not pressed firmly enough.
Firmly press the ON/OFF switch
on the machine.
DPU 130 5PIN data
Machine configuration manual 19
5 PIN data
The following table contains the factory-default PIN data:
f Note the modified PIN data in the following table:
Note: If you have forgotten the PIN, you can also unlock the machine with the
setup PIN.
However, if you have forgotten both the PIN and the setup PIN, it will
no longer be possible to unlock the machine; in this case, seek the
assistance of the Wacker Neuson representative.
Machine no.
PIN Setup PIN Modified by Date
0000
(PIN request
deactivated)
8946 Factory default setting
5PIN data DPU 130
20 Machine configuration manual
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Wacker Neuson DPU 130Le User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Wacker Neuson DPU 130Le User manual
-
-
-
-
-
-
-
-
Wacker Neuson DPU90Lem770 US User manual
-
Wacker Neuson DPU 80rLe User manual