ShelterLogic 29100.0 User manual

Brand
ShelterLogic
Model
29100.0
Type
User manual

ShelterLogic 29100.0, a 16' x 8' QuickScreen™ Double Bay Garage Screen, helps you keep out insects and other unwanted elements while providing airflow and visibility. With its easy installation, you can set it up in about an hour with two or more people. It features a roll-up pipe that can be configured for flexibility, allowing the screen to bend or flow with air currents. The hook and loop backing provides a secure attachment to your garage door frame, and the included tube caps seal the ends of the pipe for durability.

ShelterLogic 29100.0, a 16' x 8' QuickScreen™ Double Bay Garage Screen, helps you keep out insects and other unwanted elements while providing airflow and visibility. With its easy installation, you can set it up in about an hour with two or more people. It features a roll-up pipe that can be configured for flexibility, allowing the screen to bend or flow with air currents. The hook and loop backing provides a secure attachment to your garage door frame, and the included tube caps seal the ends of the pipe for durability.

05-29100-0CPage 1
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
1-800-524-9970
1-800-559-6175
Canada:
RECOMMENDED TOOLS
DESCRIPTION MODEL #
16' x 8' QuickScreen
™
29100
Before you start: 2+ individual recommended for assembly, approximate time 1 hr.
Please read instructions COMPLETELY before assembly.
16' x 8' QuickScreen
™
Double Bay Garage Screen
Assembly Instructions
11/8/10
05-29100-0CPage 2
#29100
16' x 8' QuickScreen
™
Step 1. Assemble the bottom pipe
1. Gather the (5) sections of the roll-up pipe swedged 13445 and (1) roll-up pipe plain 13444 and join the
sections together with the 13444 on one end.
2. Insert the tube caps 707 into each end of the pipe to seal the ends.
3. Set aside the roll-up pipe. (Fig. 1)
Step 3. Installing the Screen
1. Start by unfolding the garage screen and lay it out fully.
2. Fold it in an accordion style in approximately 2' folds.
3. Move the screen into place inside the garage door and align
the hook and loop side of the screen with the hook and loop
on the door jamb.
4. Grasp the top corner of the screen and align it with the hook
and loop secured to the door jamb.
5. Moving along the top of the garage door secure the hook and
loop being careful to align the two sides properly. (Fig. 4)
6. Once the top is secure repeat the process down both sides of
the garage until the entire screen is anchored to the door jamb.
Note: In order to have a more flexible screen
the roll-up pipe configuration can be changed.
There is a mid point slot in the pocket. Split the
pipe in half to allow the screen to bend or remove
half the pipe and allow half the screen to
flow with the air currents. (Fig. 5)
READ DIRECTIONS COMPLETELY BEFORE BEGINNING
Part Part No. Qty.
Garage Screen 10168 1
Roll-up Pipe 13444 1
Roll-up Pipe (Swedged) 13445 5
Hook and Loop Backing (32') 10221 1
Tube Cap 707 2
ABC
Cut
150 Callender Road Watertown, CT 06795
CUSTOMER SERVICE:
1-800-524-9970
10221
A
B
C
8'
8'
16'
C (8') A (8')
Fig. 2
Fig. 3
Fig. 4
Hole
Fig. 5
B (16')
13445 13445 13445 13445 1344413445
Fig. 1
707 707
Step 2. Attach the Hook and Loop backing
Note: The Backing can be attached to either the inside of the door jamb or the back of the jamb.
Choose the surface which provides the best area for adhesion.
Important: Make sure the mounting surface is clean and dry. Dust and debris will make the self adhesive
ineffective and will require mounting the backer using nails or staples.
1. Separate the backing into 3 sections, (2) 8' and (1) 16'. NOTE: If applying the backing to the inside of the
jamb, cut the hook and loop at 90 degrees. If applying the backing to the back of the
jamb, cut the hook and loop at 45 degrees. (Fig. 2 )
2. Beginning at floor level on one side of the door, align the backing of one 8' backing strip with the bottom
edge of the jamb. Peel back several feet of adhesive and press into place. Continue to peel and press
up to the top of the jamb.
3. Match the ends of the hook and loop so that there is a clean gap-free seam and continue across the top
of the garage.
4. Repeat the cut procedure at the other corner and continue down to the bottom of the door jamb . (Fig. 3)
Step 4. Inserting the roll-up pipe
1. Take the roll-up pipe which was assembled in step 1 and insert one end into the slot in the end
pocket at the bottom of the screen. (Fig. 5)
2. The weight of the pipe will hold down the bottom of the screen and stop the screen from moving.
05-29100-0CPage 3
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com
1-800-524-9970
1-800-559-6175
Canada:
OUTILS RECOMMANDÉS
DESCRIPTION MODÈLE Nº
4,9 x 2,4 m QuickScreen
™
29100
Avant de commencer: Il faut 2 personnes ou plus pour le montage qui prend environ 1 heures.
Lire TOUTES les instructions avant de monter.
4,9 x 2,4 m QuickScreen
™
Moustiquaire de Double Porte de Garage
Manuel d’instruction
11/8/10
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

ShelterLogic 29100.0 User manual

Brand
ShelterLogic
Model
29100.0
Type
User manual

ShelterLogic 29100.0, a 16' x 8' QuickScreen™ Double Bay Garage Screen, helps you keep out insects and other unwanted elements while providing airflow and visibility. With its easy installation, you can set it up in about an hour with two or more people. It features a roll-up pipe that can be configured for flexibility, allowing the screen to bend or flow with air currents. The hook and loop backing provides a secure attachment to your garage door frame, and the included tube caps seal the ends of the pipe for durability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents