P1
OFF
OFF
OFF
Turn off power at breaker box to
avoid possible electrical shock.
Note 1:
1. REMOVE BLADE ASSEMBLY & LIGHT KIT
Canopy
SetScrew(2)
(Removing)
Mounting Plate
Hanging Base
2
3
4
1
2. REMOVE CANOPY AND HANGING BASE SYSTEM
Note 2:
Set Screw (4)
NOTES BEFORE INSTALLATION
have the motor position of at as picture shown.
have the motor position of at as picture shown.
Mustang 90 degree
Mustang II 0 degree
Remove set screw & spring washer from motor yoke, adjust motor position as shown below.
Secure set screw & spring washer after adjustment.
REMOVAL PROCEDURE
2A. Removing Canopy & Hanging Base
Remove 4 set screws from canopy. (Keep them for Step 9B.)
Remove 2 set screws from the screw holes of hanging base. (Keep them for Step 9A.- .)
Loosen 2 set screws from the L type slots of hanging base, and move hanging base towards the left.
Remove hanging base from mounting plate.
1
2
3
4
4
Hanging Base
2
SetScrew(2)
(Loosening)
3
L Type Slot
Note 4:
This instruction manual assumes the fan has already been fully installed.
If the fan has not already been installed, you can skip Steps 1 through 3C, and start at Step 3D.
For 0 degree
Downrod Yoke
Motor Yoke
Set Screw
EXTENDED DOWNROD INSTALLATION INSTRUCTIONS
~ For Mustang and Mustang II models ~
1A.
1B.
Cap
Blade Assembly
Remove cap from blade assembly
by rotating clockwise.
Remove the blade assembly
from fan body.
Fan Body
Blade Assembly
Note 3:
Please keep the screws and parts well organized during the removal process so that all the proper screws
and parts go back to their original positions during reassembly.
For easy installation,
1
2
Set Screw & Washer
For 90 degree
Motor Yoke
Downrod Yoke
1C.( For Mustang II)
Remove the nut, glass and bulbs.
Light Kit Fitter
Bulb
Nut
Glass
Mustang Mustang II
Hanging Base
Canopy
Safety Cable
Remote
Receiver
Wires Form House
3. REMOVE WIRE CONNECTIONS
3A. Disconnect House Wires From Receiver Wires
Disconnect White wire from house and White wire from receiver by removing wire nut.
Disconnect Black wire from house and Black wire from receiver by removing wire nut.
Disconnect Ground wire from house and Ground wires from hanging base & mounting plate
by removing wire nut.
1
2
3
3B. Remove safety cable
Remove safety cable by loosening the
wood screw, spring washer and flat washer
from the ceiling.
3C. Remove fan from ceiling
Lift the fan assembly from the J hook through
oval-shaped hole on mounting plate, and remove
the whole fan to a suitable place (i.e. table)
where you can safely perform the following steps.
Safety cable
Mounting Plate
Outlet Box
J Hook
Fan Assembly
Mounting Plate
P2
2B. Hanging the fan
Lift the fan assembly and hang onto the through oval-shaped hole on mounting plate.
This will permit you to disconnect the wires connections without having to hold the fan up as well.
J hook
Hanging Base
J Hook
Canopy
1
2
3
Table
Ceiling
Mounting Plate
From House
From Fan
(Pre-wired in factory)
From Receiver
White
Black
Green
( Green )
( for ground wire )
From Hanging Base
From Mounting Plate
( Green )
White
Black
Blue
White / neutral
Black / hot
Gray
White
Black
Black
( Hot )
( Neutral )
(Hot)
(Neutral)
OSC.
MOTOR
( Light )
White
Red
Capacitor
P3
4. REMOVE DOWNROD
3D. Disconnect Fan Motor Wires
Disconnect White wire from receiver and White wire from fan by removing wire nut.
Disconnect Black wire from receiver and Black wire from fan by removing wire nut.
Disconnect Blue wire from receiver and Blue wire from fan by removing wire nut.(For Mustant II only)
1
2
3
From Fan
From Receiver
White
Black
White / neutral
Black / hot
Gray
White
Black
Black
(Hot)
(Neutral)
OSC.
MOTOR
1
2
( Light)
3
Blue
Remove 2 set screws from downrod assembly. (Keep screws for Step 7- .)
Lift up the hanging base and remove it from downrod assembly.
Lift up the canopy and remove it from downrod assembly.
(* For Mustang II, remove the yoke cover also.)
1
2
3
3
5
Note: Mustang and dual motor Mustang II have different constructions so there are 3 different steps ( )
as shown below for each model to remove downrod.
345
4
Screw (2)
5
Downrod
Downrod Yoke
Safety cable
&Wires
Set Screw (2)
Canopy
Downrod Assembly
Canopy
2
3
1
Hanging Base
Yoke
Cover
4
5
Downrod
Yoke
Cross Pin
Cotter Pin
Fan Assembly
Cotter Pin
Set Screw
& Hex nut
(Loosening)
Cross Pin
3
(For Mustang II)
Downrod
Yoke
Mustang Mustang II
Remove 2 set screws from downrod yoke. (Keep screws for Step 6- .)
(* For Mustang II, loosen 2 set screws and hex nuts. )
Remove downrod by rotating counter-clockwise and pull out the wires and safety cable carefully.
(* Dual motor Mustang II downrod does not need to be rotated out, it slides out.)
4
5
3
6
6. NEW DOWNROD INSTALLATION
5
Make sure the wires and safety cable are long enough for the new downrod installation.
Move the sleeve to the end of wires as shown below and keep it at the end while operating further steps.
Feed wires and safety cable through new downrod and insert new downrod into downrod yoke.
For single motor Mustang – Thread new downrod into downrod yoke by rotating clockwise until it goes no further,
then slightly rotate it back to have arrow mark aligned to the front screw hole of downrod yoke. (see below)
Secure downrod assembly with 2 set screws removed from Step 4- .
(* For Mustang II, tighten 2 set screws and hex nuts.)
For dual motor Mustang II – Slide new downrod into downrod yoke, aligning the large holes through both.
Insert the cross pin through yoke and downrod, and secure with the cotter pin.
1
2
3
4
5
6
4
New
Downrod
5
Yoke
Cross Pin
Cotter Pin
Fan Assembly
Cotter Pin
Set Screw
& Hex nut
(Tightening)
Cross Pin
INSTALLING PROCEDURES
5. SAFETY CABLE
1
2
3
1
2
3
3
Have crimped end of new safety cable go around original safety cable from fan by following
the direction shown as picture below.
Have copper-ring end of new safety cable pass through loop of original safety cable from fan
by following the direction shown as picture below.
Pull straight and make both loops cross tightly between end of new safety cable and
copper-ring end of original safety cable.
crimped
Note: Each new downrod is packed with one new safety cable, one end of which is looped with
and the other one end is looped with crimp .
copper ring
("copper-ring end") ("crimped end")
Copper-Ring End
Crimped End
New Safety Cable
Original Safety Cable
New Safety Cable
Safety cable
& Wires
New
Downrod
Hanging Base
1
2
Sleeve
Safety cable
Wires
P4
3
4
Arrow
Mark
New
Downrod
Downrod Yoke
Front
Screw Hole
6
Set
Screw (2)
Fan Assembly
Mustang Mustang II
Downrod
Yoke
P5
8B. Hanging the fan
Lift the fan assembly and hang onto the through oval-shaped hole on mounting plate.
This will permit you to make the wire connections without having to hold the fan up as well.
J hook
Mounting Plate
J Hook
Downrod
Canopy
Hanging Base
Remote
Receiver
7. HANGING BASE SYSTEM INSTALLATION
4
2
Hanging Base
3
Set Screw (2)
Attach the canopy by inserting downrod assembly into the center hole of canopy.
(* For Mustang II, attach the yoke cover also.)
Attach the hanging base to downrod assembly by inserting wires and safety cable through hanging base.
Secure with 2 set screws removed from Step 4- .
Move the sleeve so it is centered in steel cap of hanging base, to protect wires during oscillations.
1
1
2
3
4
Sleeve
Safety cable
&Wires
Steel Cap
Canopy
Yoke
Cover
1
Downrod
Assembly
Center Hole
Fan Assembly
8. WIRE CONNECTION
8A. Connect Receiver Wires to Fan Wires
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note: Wires from house may vary in color and may not include ground wire (green).
After wiring is completed, collect wires neatly inside hanging base.
Connect White wire from receiver and White wire from fan with wire nut.
Connect Black wire from receiver and Black wire from fan with wire nut.
Connect Blue wire from receiver and Blue wire from fan with wire nut.(For Mustang II Only)
1
2
3
1
(For Mustang II)
From Fan
From Receiver
White
Black
White / neutral
Black / hot
Gray
White
Black
Black
(Hot)
(Neutral)
OSC.
MOTOR
1
2
( Light)
3
Blue
Canopy
9B. Canopy installation
Push up canopy and secure to hanging base with 4 set screws removed from 2A.-
1
P6
Set Screw (4)
8D. Connect House Wires to Receiver Wires
Hanging Base
Canopy
Safety Cable
Remote
Receiver
Wires Form House
From House
From Fan
(Pre-wired in factory)
From Receiver
White
Black
Green
( Green )
( for ground wire )
From Hanging Base
From Mounting Plate
( Green )
White
Black
White / neutral
Black / hot
Gray
White
Black
Black
( Hot )
( Neutral )
(Hot)
(Neutral)
OSC.
MOTOR
Connect White wire from house and White wire from receiver with wire nut.
Connect Black wire from house and Black wire from receiver with wire nut.
Connect Ground wire from house and Ground wires from hanging base & mounting plate with wire nut.
1
2
3
1
2
3
9. CANOPY AND HANGING BASE SYSTEM INSTALLATION
Mounting Plate
Hanging Base
Hanging Base
1
4
3
Direction Marks
2
2
9A. Hanging base installation
Carefully lift the fan assembly away from the hook on mounting plate.
Align direction marks direction markson mounting plate with on hanging base.
Push up hanging base until 2 set screws pre-installed on mounting plate are engaged with L type slots.
Slightly rotate hanging base until 2 screw heads are in L type slots.
Attach other 2 set screws removed from Step 2A.- to secure the hanging base and mounting plate.
Make sure all 4 set screws are firmly secured.
1
2
3
4
2
Set Screw (2)
()pre-installed
Set Screw (2)
Set Screw (2)
()pre-installed
L Type Slot (2)
Note : After wiring is completed, collect wires neatly inside hanging base.
Safety cable
Mounting Plate
Wood Screw
8C. Attaching safety cable to ceiling joist
Outlet Box
Safety cable
Flat Washer
Spring Washer
Attach safety cable to the ceiling by securing the wood screw, spring washer and flat washer.
10. BLADE ASSEMBLY INSTALLATION
Blade Assembly
Beveled Motor
Shaft
12. Turn on the power at breaker box - your fan is ready for operation.
10A. Attach blade assembly to fan
10B. Attach cap to blade assembly
Align beveled center hole on flywheel with
beveled motor shaft before attachment.
Thread the cap counter-clockwise to motor
shaft until fully tightened.
Flywheel
Flywheel
Cap
11. LIGHT KIT INSTALLATION (FOR MUSTANG II ONLY)
11A.
Install the bulbs (included) to the
medium sockets (sockets) properly.
11B.
Align the hole on the glass with the
threaded tube from light fixture.
Attach the glass to light fixture.
11C.
Attach the nut to the threaded
tube tightly.
Glass
Light kit fitter
Light kit fitter
Light kit fitter
Nut
Glass
Medium Sockets
Bulb
(13W CFL bulb)
Bulb
(13W CFL bulb)
P7
/
