TroposAir 88111 Installation guide
- Category
- Household fans
- Type
- Installation guide
3MT18-2M
10.0 KGS.
22.0 LBS.
Net weight
This instruction contains 6 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained
Page 3: Notes before installation and Hanging system installation
Page 4: Wire connection
Page 5: Hanging base & Canopy installation / Set up m
Page 6: Blade / L
otor position
ight kit installation and Remote & Setting
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
U
L
R
Mustang II
Owner’s Manual
Toll Free: 1-855-676-7247
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING :
READ AND SAVE THESE INSTRUCTIONS
1 . To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is TURNED OFF at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any object.
Fan must be installed at least 7 feet from floor to prevent injury when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward. The wires should be
spread apart with the grounded conductor and the equipment-grounding conductor on one side and the
"HOT" wires on the other side.
7]. After fan is completely installed, check to make sure that all connections are secure to prevent fan from
falling and/or causing damage or injury.
8]. This fan is not suitable for slope ceiling.
9]. This fan is not reversible.
10]. This fan is suitable for damp location use.
]
P1
Mounting Plate
Canopy
Downrod
Fan Assembly
Blade x6
Glass
CFL Bulb
(13W) x 2
Decorative Cap
Unpack and inspect fan carefully to be certain
all contents are included.
P2
Remote
Hardware Bag
Wood Screw x2
*Battery Included
Flat Washer x3
Spring Washer x3
Machine Screw x2 Wood Screw x3
For Mounting Plate:
For Hanging Base :
Set Screw x 2
For Wire Connection:
WireNutx4
For Blade Installation:
Blade Screw x 13
(one spare screw included)
Paper Washer x 13 (one spare washer included)
Hardware Bag
For Canopy:
Set Screw x 5
(one spare screw included)
osc
Cap
Flywheel
Hanging Base
(with receiver and
oscillating motor)
Yoke Cover
Safety cable
&Wires
P3
OFF
OFF
OFF
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
Installing mounting plate to ceiling outlet box
CAUTION:
Oscillating device located
at hanging base is fragile,
do not damage or bend
oscillating parts (cam/arm/motor)
during installation
Note 1: Note 2: Note 3:
cam
motor
arm
Hanging Base
Mounting Plate
Outlet Box
House Wires
1A.
Pull house wires from outlet
box through the center hole
of mounting plate
Direction Mark
Outlet Box
Screw hole
Mounting slot
Outlet Box
Mounting
Plate
( fig.1)
1B.
Direction marks are for finding the air
direction. Direction marks show the certerline
position between the motors. Motors will be
90 degrees to the left and right of the direction
mark. Adjust mounting plate to the desired
position by aligning 2 slots of mounting plate
with screw holes on outlet box.
1E. Hanging the fan
Lift the fan assembly and hang onto the
through oval-shaped hole on mounting plate.
This will permit you to make the electrical
connections without having to hold the fan up as well.
J hook
Mounting Plate
J Hook
Downrod
Canopy
Hanging Base
Remote
Receiver
1D. Yoke & Downrod Assembly
Yoke
Cross Pin
Canopy
Cotter Pin
Fan Assembly
Cotter Pin
Set Screw
Cross Pin
( fig.2)
( fig.3)
Remove cotter pin and cross pin secured on downrod
and pull out lead wires inside downrod slightly and
insert downrod into yoke (see fig. 2).
Attached cotter pin and cross pin back through yoke
and downrod securely (see fig. 3).
M
a
x
i
m
u
m
s
w
e
e
p
a
r
e
a
:
5
8
3
s
q
u
a
r
e
f
e
e
t
(
5
4
.
2
s
q
u
a
r
e
m
e
t
e
r
)
WARNING: Fan should be at least 7 feet from the floor
1. HANGING SYSTEM INSTALLATION
1C.
Attach mounting plate to outlet box
by securing with screws included
with the outlet box and washers
from the hardware bag through 2
out of 6 slots on mounting plate.
IMPORTANT: Align Mounting Plate to desired oscillator direction now.
P4
2B. Making electrical wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note: Wires from house may vary in color and may not include ground wire (green).
After wiring is completed, collect wires neatly inside hanging base.
2. WIRE CONNECTION
Use wood screw, spring washer, and flat washer from hardware bag. Pass wood screw through closed loop of safety cable.
Secure wood screw to ceiling joist through any available slot on mounting plate. Make sure safety cable has been
tightened securely. CAUTION: THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT
THE WEIGHT OF AT LEAST 100 LBS.
2A. Attaching safety cable to ceiling joist
*White wire from house to white wire from receiver
*Black wire from house to black wire from receiver
*Ground wire from house to green wire from hanging base and from mounting plate
*Secure with twist - lock wire nuts. (Included)
Hanging Base
From House
From Fan
(Pre-wired in factory)
From Receiver
White
Black
Green
( Green )
( for ground wire )
From Hanging Base
From Mounting Plate
( Green )
White
Black
Blue
White / neutral
Black / hot
Gray
White
Black
Black
( Hot )
( Neutral )
(Hot)
(Neutral)
OSC.
MOTOR
Canopy
Safety Cable
Remote
Receiver
Wire Form House
( Light )
White
Red
Capacitor
Remove battery cover.
Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down.
Slide code switch for light ON/OFF (marked as X), or DIMMING (marked as D) function.
Install 9V DC battery.(Included)
Install battery cover on transmitter.
1.Setting the code on the TRANSMITTER
1
2
3
4
5
2C. Setting code switches for transmitter
Remote controls are tuned to operate together using 4 switches for 16 possible code combinations.
Important! This fan includes 2 CFL bulbs, so the code switch should be at X position (ON/OFF).
You may switch code at D position (DIMMING) once incandescent bulbs are installed.
!
Warning! CFL bulbs are not applicable to the remote with dimming function.
1
4
5
D: for light dimming
(for incandescent bulbs )
X: for light ON/OFF
(for CFL bulbs)
Transmitter
Code Switches
1
2
3
4
2
X
D
ON
3
1
2
3
4
X
D
ON
Safety cable
Mounting Plate
Outlet Box
Safety cable
Flat Washer
Spring Washer
Wood Screw
Outlet Box
P5
Screws on
Mounting Plate
3. HANGING BASE AND CANOPY INSTALLATION
3B. Push up canopy and secure to hanging base with 4 set screws from hardware bag.
Mounting Plate
Hanging Base
Hanging Base
1
4
( fig.1) ( fig.2)
3
3A.
Carefully lift the fan assembly away from the hook on mounting plate.
Slightly rotate hanging base until two screw heads are in L type slots.
Attach other 2 set screws from hardware bag to secure hanging base and mounting plate (these will be
the remaining 2 out of 4 set screws for securing hanging base to mounting plate).
1
2
Align direction marks direction markson mounting plate with on hanging base.
Push up hanging base until 2 set screws pre-installed on mounting plate are engaged with L type slots
on hanging base.
Make sure all 4 set screws are firmly secured.
(see fig.1)
(see fig.1)
(see fig.2)
(see fig.2)
3
4
Note:
Canopy
4. SET UP MOTOR POSITION
Motor Yoke
For 0 degree
Downrod Yoke
Motor Yoke
Downrod Yoke
For 45 degree For 90 degree
Motor Yoke
Downrod Yoke
Downrod Yoke
Set Screw
Motor Yoke
( fig.1)
( fig.2)
Set Screw
Set Screw
Set Screw
NOTE:
1.Fan motor is at 0 degree when taken out from the carton, no need to change motor angle
2.
if intend
to use the fan at 0 degree.
Both motor positions must be set at the same angle.
There is and for aligning 0/45/90 degree motor
position (see fig. 1)
Remove set screw and spring washer from motor yoke. (see fig. 2)
Adjust motor angle by aligning
.(see fig. 2)
Secure set screw and spring washer removed from step 4A back to motor yoke. Make sure set screw is
firmly tightened.(see fig. 2)
one indicating line on downrod yoke three on motor yoke
one out of three indicating lines (0/45/90) on motor yoke with
indicating line on downrod yoke
4A.
4B.
4C.
Indicating Line(1)
Indicating Line(3)
2
2
P6
5. BLADE INSTALLATION
5A.
Attach blade to blade
with screws & washers provided
in hardware bag. Make sure that
all screws are firmly tightened.
holder
Attach blade assembly to flywheel,
.
5B.
aligning beveled center hole on
flywheel with beveled motor shaft
before attachment
Thread the cap
to motor shaft until fully tightened.
(*This is reverse threaded.)
5C.
counter-clockwise
Blade
Flywheel
Cap
Blade Assembly
Beveled Motor
Shaft
6. LIGHT KIT INSTALLATION
6A.
Install the bulbs (included) to the
medium sockets (sockets) properly.
6B.
Align the hole on the glass with the
threaded tube from light fixture.
Attach the glass to light fixture.
6C.
Attach the nut to the threaded
tube tightly.
Glass
Light kit fitter
Light kit fitter
Light kit fitter
Nut
OSC: Button for ON/OFF oscillation
(*this button only functions
when fan is in operation)
7. REMOTE & SETTING
osc
D/L: ON/OFF button
for down light
Glass
Medium Sockets
Bulb
(13W CFL bulb)
Bulb
(13W CFL bulb)
Turn on power at breaker box for remote setting.
Pressing the button for 3~5 seconds till the , which means this remote control
has done the setting. Now the remote is ready for operation.
“OFF” LIGHT BLINKS
MED:Fan middle speed
HI:Fan high speed
LOW:Fan low speed
OFF: For SETTING /
Fan speed & Oscillation
2
X: for light ON/OFF
(for CFL bulbs)
D: for light dimming
(for incandescent bulbs)
1
2
3
4
X
D
ON
1
2
3
4
X
D
ON
Note: You may switch Light switch code at D position
(DIMMING) when you change to incandescent bulbs
for Down light.
SETTING for before starting fanlight operation
-
1
-
2
-
3
-
4
-
5
-
6
-
7
TroposAir 88111 Installation guide
- Category
- Household fans
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
TroposAir 88631 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Crystorama CHI-211-PN Operating instructions
-
Aero Mist 67014 User manual
-
Yosemite Home Decor LK498AP User guide
-
Design House 157347-BN Installation guide
-
Yosemite Home Decor ASHLEY-BBN Operating instructions
-
Canarm CF52SIM4BK Operating instructions
-
-
-
Yosemite Home Decor LK498AP Operating instructions
-
Feiss F2052/6+3GBZ Installation guide
