Biostar P4M800Pro-D1 Owner's manual

P4M800Pro-D1 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protec tion against harmful interference in a reside ntial

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that inte rference will not occur in a particular ins talla tion.

The vendor makes no re presentations or warra nties with respec t to the

contents here and specially disclaims any implied warranties of merchantability

o r fi tnes s fo r a ny p urpos e . F urthe r t he ve nd o r rese rves t he ri g ht to rev ise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

D uplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be res ponsible for any mis takes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction .............................................3

1.1 Before You Start................................................................... 3

1.2 Package Checklist................................................................3

1.3 Motherboard Features.......................................................... 4

1.4 Rear Panel Connectors..........................................................5

1.5 Motherboard Layout............................................................6

Chapter 2: Hardware Installation..............................7

2.1 Installing Central Processing Unit (CPU)................................7

2.2 FAN Headers........................................................................9

2.3 Installing System Memory.....................................................10

2.4 Connectors and Slots............................................................11

Chapter 3: Headers & Jumpers Setup .....................13

3.1 How to Setup Jumpers..........................................................13

3.2 Detail Settings.....................................................................13

Chapter 4: RAID Functions.......................................19

4.1 Operation System................................................................19

4.2 Raid Arrays.........................................................................19

4.3 How RAID Works.................................................................19

Chapter 5: Useful Help .............................................21

5.1 Driver Installation Note .......................................................21

5.2 AWARD BIOS Beep Code......................................................22

5.3 Extra Information................................................................22

5.4 Troubleshooting...................................................................24

Appendencies: SPEC In Other Language ................26

German................................................................................................26

France..................................................................................................28

Italian..................................................................................................30

Spanish................................................................................................32

Portuguese...........................................................................................34

Polish...................................................................................................36

Russian................................................................................................38

Arabic..................................................................................................40

Japanese..............................................................................................42

P4M800Pro-D1

3

CHAPTER 1: INTRODUCTION

1.1 BEFORE YOU START

Tha nk you for choosing our pro duct. Be fore you start installing the

mothe rboard, plea se make sure you follo w the instructio ns be lo w:

 Prepare a dry and stable working environment with

s uf ficie nt ligh ting.

 Always disconnect the computer from power outlet

be fo re ope ra tion.

 Befo re you take the m o the rboa rd ou t f rom a n ti -s ta tic

bag, ground yourself properly by touching any safely

grounde d appliance, or use gro unded wrist strap to

remove the static charge.

 Avo id tou ch ing the compone nts o n mo the rboa rd o r the

rear side of the board unless necessary. Hold the board

on the edge , do not try to bend or flex the board.

 Do not lea ve any unfastened small pa rts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source , humid air and wate r.

1.2 PACKAGE CHECKLIST

HDD Cable X 1

Use r’s Manual X 1

Fully Setup Driver CD X 1

Rear I/O Panel for ATX Case X 1

FDD Cable X 1 (optional)

Se ria l ATA Cab le X 1 (op tiona l)

USB 2.0 Cable X1 (optional)

S/PDIF Cable X 1 (optional)

Motherboard Manual

4

1.3 MOTHERBOARD FEATURES

SPEC

CPU

LGA 775

Supports Intel Core2Duo / Pentium 4

/ Pentium D / Celero n D

p

rocessor u

p

to 3.8 GHz

Supports Hy per -Thre ading Techn ology / Execute

Disable Bit/ Enhanced Intel S peedStep® / Intel

Extended Memory 64 technology

FSB 400 / 53 3 / 8 00 / 10 66 MHz

Chipset

VIA P4M800 PRO

VIA VT8237R+

Graphic Integrated i n U niChrome Pro Chipset Max Share d Vide o Memory is 64 MB

Super I/O

ITE IT87 05

Provides the most commonly used

legacy Super I/O functionality.

Low Pin C ount Interf ace

Environment Control initiatives,

H/W Monitor

Fan Spee d Co ntroller

ITE's "Smart G uardia n" fu nction

Main

Memory

DIMM Slots x 2

Supports D DR 400 / 333

Each DIMM supports

256MB/ 51 2MB/1GB DDR

Max Memory C apacity 2GB

Single Channel Mode DDR memory module

Registered DIMM and ECC DIMM is not supported

IDE Integrated I DE Controller

Ultra DMA 33~133 Bus Master Mode

supports PIO Mo de 0~4,

SATA Integrated Serial ATA Controller

Data transfer rates up to 1.5 Gb/s.

SATA Version 1.0 specification compliant.

LAN PHY Realtek RTL8201CL

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound

Codec

ALC655 / ALC65 8

6 channels audio out

AC’97 Version 2.3

AGP slot x1 Supports AGP expansion cards

CNR slot x1 Supports CNR expansion cards Slots

PCI slot x3 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Connector x2 Each connector supports 2 IDE device

SATA Connector x2 Each connector supports 1 SATA devices

On Board

Connector

Front Panel Connector x1 Supports front panel facilities

P4M800Pro-D1

5

SPEC

Front Audi o Co nnector x1 Supports front panel a udio function

CD-in Co nnector x1 Supports CD au dio-in f unction

S/PDIF out connector(optional) x1 Supports di gital audio out function

CPU Fan hea der x1 CPU Fan power s upply (with Smart Fa n function)

System Fan hea der x1 System Fan Power supply

Chassis open header(optional) x1 For chassis intruder detection function

Clear CMO S head er x1 Restore CMOS data to factory d efa ult

USB connector x2 Each connector supports 2 front panel USB ports

Power Connector (20pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mo use x1

Serial Port x1

Printer Port x1

VGA Port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/ 2 Mouse

Provide RS- 23 2 Serial c onnection

Connects to various types of device

Connects to mo nitor.

Connects to RJ-45 ethernet cable

Connects to USB devices

Provide Au dio-In/Out a nd microph one co nnection

Board Size 201 mm (W) x 24 4 mm (L) Mic ro ATX form Factor

Special

Features

RAID 0 / 1 support

OS

Support

Windows 2000 / XP

Biostar Reserves the right to add or remove

support for any OS with or without notice.

1.4 REAR PANEL CONNECTORS

PS/2

Mouse

PS/2

Keyboard

COM1 VGA1 USBX2USBX2

LAN

Line In/

Surround

Line Out

Mic In 1/

Bass/ Center

Printer Port

Motherboard Manual

6

1.5 MOTHERBOARD LAYOUT

BIOS

PCI1

FDD1

CNR1

BAT1

PCI3

PCI2

IDE1

IDE2

JATXPWR1

JC FAN 1

JSFAN 1

JUSBV2

JCMOS1

JU SB2

JUSB3

JSATA2

JC I 1

(option al)

JPAN EL 1

JSAT A1

VT8237R+

P4M800 Pro

JFAUDIO1

JCDIN1

JSPDIFO1(Optional)

Co de c

AGP1

LGA775

CPU 1

LAN

DI MM1

DI MM2

JKBMS1

JUSB1

JAUDIO1

JATXPWR2

JUSBV1

Super

I/O

JP RNT 1

JVGA1

J

C

O

M

1

JUSBLAN1

JAUX1

(op ti onal)

IR (optional)

No te: represents the 1■

st

pin.

P4M800Pro-D1

7

CHAPTER 2: HARDWARE INSTALLATION

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation

for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

Motherboard Manual

8

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will

fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into

the JCFAN1. This completes the installation.

P4M800Pro-D1

9

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3 FAN RPM rate

sense

1

4

4 Smart Fan

Control

JSFAN1: System Fan Header

Assignment

1 Ground

2 +12V

13

3 FAN RPM rate

sense

Note:

The JCFAN1 and JSFAN1 support 4-pin and 3-pin head connectors. When connecting

with wires onto connectors, please note that the red wire is the positi ve and shoul d be

connected to pin#2, and the bl ack wire is Ground and should be connected to GND.

Motherboard Manual

10

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMM1

DIMM2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

B. Memory Capacity

DIMM Socket

Location

DDR Module

To t a l Me m o r y

Size

DIMM1 256MB/512MB/1GB

DIMM2 256MB/512MB/1GB

Max is 2GB.

P4M800Pro-D1

11

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cable.

34

33

1

2

IDE1/IDE2: Hard Disk Connectors

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. It has two

HDD connectors - IDE1 (primary) and IDE2 (secondary).

The IDE connectors can connect a master and a slave drive, so you can

connect up to four hard disk drives. The first hard drive should always be

connected to IDE1.

IDE2IDE1

21

3940

Motherboard Manual

12

PCI1~PCI3: Peripheral Component Interconnect Slots

This motherboard is equipped with 3 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

PCI3

AGP1: Accelerated Graphics Port Slot

Your monitor will attach directly to that video card. This motherboard supports

video cards for PCI slots, but it is also equipped with an Accelerated Graphics

Port (AGP). An AGP card will take advantage of AGP technology for improved

video efficiency and performance, especially with 3D graphics.

A

GP1

CNR1: Communication Network Riser Slot

The CNR specification is an open Industry Standard Architecture, and it defines

a hardware scalable riser card interface, which supports modem only.

CNR1

P4M800Pro-D1

13

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 HOW TO SET UP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SET T ING S

JPANEL1: Front Panel Header

This 24-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep

button, speaker and IrDA (optional) Connection. It allows user to connect the PC

case’s front panel switch functions.

123

24

SLP

PWR_LED

On/Off

IR (optional)

RS T

HL ED

SPK

++

+

2

-

Pin Assignment Function Pin Assignment Functio n

1 +5V 2 Sleep control

3 N/A 4 Ground

Sleep button

5 N/A 6 N/A N/A

7 Speaker

Speaker

Connector

8 Power LED (+)

9 HDD LED (+) 10 Power LED (+)

11 HDD LED (-)

Hard drive LED

12 Power LED (-)

Power LED

13 Ground 14 Power button

15 Reset control

Reset button

16 Ground

Power-on button

17 N/A 18 N/A

19 N/A 20 Key

21 +5V 22 Ground

23 IRTX

IrDA Connector

(optional)

24 IRRX

IrDA Connector

(optional)

Motherboard Manual

14

JATXPWR1: ATX Power Source C onne ctor

This connector allows user to connect 20-pin power connector on the ATX

power supply.

10 20

111

Pin Assignment Pin Assignment

1 +3.3V 11

+3.3V

2 +3.3V 12

-12V

3 Ground 13

Ground

4 +5V 14

PS_ON

5 Ground 15

Ground

6 +5V 16

Ground

7 Ground 17

Ground

8 PW_OK 18

-5V

9 Standby Voltage +5V 19

+5V

10 +12V 20

+5V

JATXPWR2: ATX Power Source C onne ctor

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

12

34

4 Ground

P4M800Pro-D1

15

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

1

2

9

10

JUSB2

JUSB3

10 NC

JUSBV1/JUSBV2: Powe r Source Headers for USB ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JUSB1 and JUSBLAN1.

JUSBV2: +5V for USB ports at front panel (JUSB2/JUSB3).

Pin 2-3 Close:

JUSBV1: USB ports at JUSB1 and JUSBLAN1 are powered by +5V

standby voltage.

JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V

standby voltage.

31

1

3

Pin 1-2 close

1

3

13

JUSBV1

JUSBV2

3

1

3

Pin 2-3 close

Note:

In order to support this function “Power-On system via USB device,” “JUSBV1/ JUSBV2”

jumper cap should be placed on Pin 2-3 indi viduall y.

Motherboard Manual

16

JFAUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. It will disable the output on back panel audio connectors.

Pin Assignment

1 Mic-in/Stereo MIC-in

R

2 Ground

3 Stereo MIC-in L

4 Audio power

5 Right line-out/

Speaker-out Right

6 Right line-out/

Speaker-out Right

7 Reserved

8 Key

9 Left line-out/

Speaker-out Left

10 Left line-out/

Speaker-out Left

11 Right line-in (optional)

12 Right line-in (optional)

13 Left line-in (optional)

1

2

13

14

14 Left line-in (optional)

JCDIN1: CD-ROM Audio-in Connector

JAUX1: Audio-in Connector (Optional)

This connector allows user to connect the audio source from the variaty devices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

1 Left Channel Input

2 Ground

3 Ground

14

JCDIN1

JAUX

1

4 Right Channel Input

P4M800Pro-D1

17

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting

and the CMOS data, please carefully follow the procedures to avoid damaging

the motherboard.

31

Pin 1-2 Close:

Normal Operation (default).

13

3

1

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

JSATA1/JSATA2: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 2 channels SATA interface,

it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

147

JSATA2

JSATA1

147

7 Ground

Motherboard Manual

18

JSPDIFO1: Digital Audio-out Connector (Optional)

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

13

3 Ground

JCI1: Chassis O pen Header (Optional)

This connector allows system to monitor PC case open status. If the signal has

been triggered, it will record to the CMOS and show the message on next

boot-up.

Assignment

1 Case open signal

12

2 Ground

P4M800Pro-D1

19

CHAPTER 4: RAID FUNCTIONS

4.1 OPERATION SYSTEM

Supports Windows XP Home/Professional Edition, and Windows 2000 Professional.

4.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

4.3 HOW RAID WORKS

RAID 0:

The controller “ stripes” data across multiple drives in a RAID 0 array system. It breaks

up a large file into smaller blocks and performs disk reads and writes across multiple

drives in parallel. The size of each block is determined by the stripe size parameter,

which you set during the creation of the RAID set based on the system environment. This

technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

 Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the

platform.

 Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

 Benefits: provides increased data throughput, especially for large files. No

capacity loss penalty for parity.

 Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

 Fault Tolerance: No.

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

Motherboard Manual

20

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1

array system. The mirrored (backup) copy of the data can reside on the same disk or on

a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if

the active volume or drive is corrupted or becomes unavailable because of a hardware

failure.

RAID techniques can be applied for high-availability solutions, or as a form of

automatic backup that eliminates tedious manual backups to more expensive and less

reliable media.

Features and Benefits

 Drives: Minimum 2, and maximum is 2.

 Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

 Benefits: Provides 100% data redundancy. Should one drive fail, the

controller switches to the other drive.

 Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

 Fault Tolerance: Yes.

Block 1

Block 2

Block 3

Block 1

Block 2

Block 3

Page is loading ...

Biostar P4M800Pro-D1 Owner's manual

Biostar P4M800Pro-D1 Owner's manual

Related papers

Other documents