Sony SAT-A2/ SAT-B2 Digital Satellite Receiver User manual

Brand: Sony

Model: SAT-A2/ SAT-B2 Digital Satellite Receiver

Category: LED TVs

Type: User manual

3-856-591-21(1)

Digital Satellite

Receiver

Operating Instructions

SAT-A2

SAT-B2

BEFORE USING YOUR DSS SYSTEM

You must activate your programming service

by calling your program providers:

DIRECTV® 1-800-347-3288

USSB 1-800-204-8772

For more information, see page 25.

SAT-A2 MODEL ONLY

RF ANTENNA: The DSS receiver is shipped

with IR reception enabled and RF reception

disabled. To use the RF feature (and the

antenna), you must change the factory setting

(IR ONLY) to the RF setting (RF ONLY) using the

on-screen displays, as described in this

manual.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or

moisture.

Note to the CATV Installer

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the building

as close to the point of cable entry as practical.

Note to the DSS® Satellite Dish Installer

This reminder is provided to call the DSS satellite dish installer’s

attention to Article 810 and in particular Article 810-15 of the NEC,

which covers proper installation and grounding of television

receiving equipment, as well as to Article 820-40 of the NEC,

which specifies that the satellite dish cable ground shall be

connected to the grounding system of the building as close to the

point of cable entry as practical.

Telephone Line Interruption

Periodically, information on your DirecTicket and Pay-Per-View

selections is sent, free of charge, via your telephone line to an 800

number. During the time the information is being forwarded, you

cannot use your telephone and you will hear static noise for

approximately 30 seconds. If you would like to use your telephone

while the information is being sent, you can interrupt the sending

of this information at any time by temporarily unplugging the

phone line to the receiver.

This symbol is intended to alert the user to the

presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

significant magnitude to constitute a risk of

electric shock to persons.

This symbol is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

Owner’s Record

The model and serial numbers are located on the back of the

receiver. The number for the access card is on the front of the card

and on the carton label. Record these numbers in the space

provided below. Refer to these numbers whenever you need to call

your sales or service representative regarding this product.

Model Number: ___________________________________________

Serial Number:_____________________________________________

Access Card Number:_______________________________________

Customer Support

For DSS Programming

For subscription information, or to resolve problems related to

DSS programming, call:

DIRECTV® at 1-800-DIRECTV (347-3288) or

USSB at 1-800-204-USSB (8772).

For DSS Hardware and Installation

To arrange for the installation of your DSS system, call the dealer

from whom you purchased your system.

For general information, or to resolve problems related to the

operation of your satellite receiver or antenna, please contact your

Sony brand DSS dealer. If your dealer or installer is unable to

answer your questions, call the Sony Digital Satellite System

Information Center at 1-800-838-7669.

Trademark and Copyrights

Express Navigator is a trademark of Sony Corporation. DIRECTV

and DSS are registered trademarks of DIRECTV, Inc., a unit of

Hughes Electronics. USSB and USSB Entertainment Plus are

official service marks of the United States Satellite Broadcasting

Company, Inc. HBO is a registered trademark of Time Warner

Entertainment Company, L.P. Showtime is a service mark of

Showtime. MTV: Music Television is a registered trademark of

MTV Networks, a division of Viacom International Inc. Comedy

Central is a registered trademark of Comedy Partners.

Macrovision Information

This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology is granted by

Macrovision for home and other limited DSS IRD pay-per-view

uses only. Reverse engineering or disassembly is prohibited.

Note on Recording Programming

Programming may be taped for home viewing only. All other

taping is expressly prohibited. Some programming may not be

taped. An additional taping fee may be applied. Call your

program providers for details.

StarSight Licensed

The manufacture and sale of the television schedule feature of this

product was licensed under one or more of the following patents

of StarSight Telecast, Inc.: U.S. Patent Nos. 4,706,121; 4,977,455;

5,151,789; and 5,353,121; with use rights reserved.

Network Broadcasting Information

ABC, CBS, NBC, FOX, and PBS networks are available from

DIRECTV. Some restrictions apply.

Contents 3

Contents

Chapter 1

Introducing the DSS System

4 DSS Features

5 Package Contents

6 Inserting Batteries into the Remote Control

Chapter 2

Using Basic Functions

7 Remote Control for Model SAT-A2

8 Remote Control for Model SAT-B2

9 Using a Program Guide

10 Using the Station Index

Chapter 3

Connecting Your System

11 Overview

12 TV Only

14 TV and VCR

16 Hi-Fi TV, Hi-Fi VCR, Audio Receiver

(SAT-A2 Only)

18 Home Entertainment System

(Hi-Fi TV, Hi-Fi VCR, Audio/Video

Receiver)

20 Connecting the VCR Mouse

21 Connecting Digital Audio Components

(SAT-A2 Only)

22 Setting Up the RF Antenna (SAT-A2 Only)

23 Setting Up Your DSS System

Chapter 4

Using the System Features

24 Overview

25 Before You Get Started ...

26 Using the On-Screen Displays:

Highlight and Select

27 Displaying the Program Guide

28 Features of the Program Guide

29 Moving Through the Program Guide

31 Selecting a Program from the Guide

32 Selecting a Program List

33 Selecting a Different Program Guide or List

36 Using the Station Index

38 Setting Up the Timer

40 Using the Favorite Station Guides

43 Displaying the Program Banner

44 Using the DISPLAY Feature

Chapter 5

Using the Options Menu

45 Overview

46 Displaying the Options Menu

47 Checking and Cancelling PPV Purchases

48 Setting Display Options

51 Using the Jump Loop Feature

52 Setting Locks and Limits

57 Setting Up a List of Custom Stations

59 Selecting Alternate Audio

61 Reading Your Messages

63 Selecting Data Services

Chapter 6

Using the Setup Menu

65 Overview

66 Displaying the Setup Menu

67 Setting Up the Satellite Antenna

68 Replacing Your Access Card

70 Setting the Aspect Ratio

71 Setting Up the Remote Control

75 Running a System Test

76 Displaying Help, Tips, and Shortcuts

Appendix

Other Information

78 Location and Function of Controls

81 Using the Remote Control

85 Programming the Remote Control

87 Using the Learn Function (SAT-A2 Only)

88 Troubleshooting

91 Precautions

92 FCC Regulations and Information

93 Limited Warranty

94 Specifications

95 Index

4 Chapter 1: Introducing the DSS System

Chapter 1

Introducing the DSS System

Welcome to the Sony brand DSS (Digital Satellite System), the ultimate

digital entertainment experience. Read this chapter for an overview of

the features of the system and to check the carton contents of the DSS

receiver.

DSS Features

Here are just a few benefits of the DSS system that you'll enjoy:

Excellent Performance

Superior, digital-quality video that rivals the performance of

laserdisc players.

Crisp digital-quality audio that will enhance your TV or home

theater experience.

Premium Entertainment

Choose from a variety of program packages available through your

program providers, DIRECTV® and USSB

Convenience and Ease-of-Use

Order premium pay-per-view (PPV) movies. PPV programs start

as often as every 30 minutes, so you can watch programs when you

want to see them.

Sony’s Express Navigator on-screen display system guides you

through all the system features and functions.

Select from a variety of program guides that are sorted by program

categories, including Sports, Movies, News, and more.

The Timer feature, when used with Sony’s VCR Mouse, allows you

to easily automate the recording of DSS programs.

Customizable

Create a Custom Program Guide and up to five of your own

Favorite Station Guides for stations you watch most often.

Change the color palette, transparency, and station ordering of the

program guides. Use the DISPLAY button to toggle among

different sizes of on-screen displays.

Set up a passcode, which lets you choose spending limits and

control viewing of programs by rating and station.

Chapter 1: Introducing the DSS System 5

Package Contents

Check to make sure you’ve received the following items in the DSS

receiver’s carton:

* RF Antenna and S-Video cable not included with SAT-B2. SAT-A1

includes RM-Y130 remote control shown above; SAT-B2 includes

RM-Y129 remote control shown on page 8.

The access card comes already inserted into the DSS receiver.

If you are missing items, contact the dealer from whom you purchased

the DSS receiver.

Note

Keep the original carton and packing materials to safely transport the system

in the future.

6 Chapter 1: Introducing the DSS System

Inserting Batteries into the Remote Control

Before you can use the remote control, you must first insert the

supplied batteries. If you want to use this remote control to operate

other video components, such as a TV or cable box, you must also

program the remote as described in the Appendix on page 85.

To install the batteries:

1 Push and slide open the battery compartment.

SAT-A2 Remote Control:

SAT-B2 Remote Control:

2 Insert two size AA batteries (supplied). Be sure to line up the + and

– on the batteries with the + and – on the battery compartment.

Notes on Batteries

When the batteries become weak, the Function button indicator

blinks. If the remote control does not operate properly, the batteries

might be worn out. When replacing batteries, replace both of them

with new ones, and do not mix different types of batteries together.

When you remove the batteries — to replace them, for example —

any codes you’ve set may be erased. If this happens, you must

reprogram the remote. See “Programming the Remote Control” on

page 85 for details.

Chapter 2: Using Basic Functions 7

Chapter 2

Using Basic Functions

You can start watching programs using just a few buttons on the

remote control. Here’s an overview of the buttons you’ll use most

often.

Remote Control for Model SAT-A2

See Also

Pages 9–10 for a quick start to using the program guide and the

Station Index.

Chapter 4 for procedures for using the main system features.

Page 84 for a complete description of the buttons on the remote.

Arrow Buttons

Scrolls through the program guide.

Button

Selects the program that’s highlighted. When a program guide is not

displayed, pressing the button brings up the Station Index.

GUIDE Button

Brings up the Custom Guide.

DSS POWER Button

Turns the DSS receiver on and off.

0–9 and ENTER Buttons

Pressing the 0–9 buttons and then the ENTER button selects a station

number directly.

FUNCTION Buttons

Selects the component (DSS, TV, CABLE) that you want to operate.

These buttons flash to indicate which component the remote control

is set to operate. To control your TV or cable box, you must first

program the remote control, as described on page 85.

CH/PAGE Buttons

Changes the channel. When a program guide is displayed, pressing

the CH/PAGE buttons pages through the guide.

Chapter 2: Using Basic Functions 9

Using a Program Guide

The program guide displays the programming that’s available from

your program providers.

1 Press the GUIDE button to bring up the Custom Guide.

2 Move the highlight to the name of the program you want.

You’ll hear the audio and see the video (in the background) of each

program as they are highlighted.

The table below lists the various ways in which you can move

around in the guide.

3 Press the button to select the highlighted program.

Moving Around

In a Program Guide

To Do This ... Use This Button

Go to other stations in the

guide one station at a time

SAT-A2: Move the joystick up and

down

SAT-B2: Press the and buttons

You can also change the look of the program

guide by pressing the DISPLAY button. See

“Using the DISPLAY Feature” on page 44.

Go to other time slots in the

guide one program at a time

SAT-A2: Move the joystick left and

right to move one time slot at a time.

SAT-B2:

Press the and buttons

Both Models: Or press the GUIDE

button to “page” to future time slots.

Go to other stations in the

guide one “page” at a time

Press the PAGE (CH+) and

PAGE (CH-) buttons

In program guides, you can select station

call letters/numbers to display a description

of the station.

Go to a station directly

Press the 0-9 buttons and press ENTER

(to specify the station number)

Return to the last station you

were watching

Press the EXIT button

First Knight

8:00 PM 10:00 PM PG-13

Act. Adv. 1995 Richard Gere, Sean Connery, Julia

Ormond. Thrilling romance results when rogue knight

Lancelot becomes torn between his loyalty to King

Arthur and his love for Queen Guinevere (CC, ST) (A, V)

CUSTOM GUIDE WED OCT 5 8:45 PM

BoxingSHO2987

First Knight

DTV 102

The Alamo

MTV 989

Most Wanted ...MTV’s Best of the 90’s

COM990 It’s Gary Shan...Tracy Ullman

USSB999

USSB Programming Highlights

DTV 105

Jefferson in Par...Johnny Mnemonic

8:00 PM 8:30 PM 9:00 PMWED

DTV 100 Direct Ticket Previews

10 Chapter 2: Using Basic Functions

Using the Station Index

The Station Index lets you select a program from a grid of station logos

and call letters.

Note

Before you can bring up the Station Index, you must first clear the program

guide from your TV screen. Pressing EXIT removes all on-screen displays.

Also, you may need to change to another station if a message appears, which

requests that you press the button to purchase the program, etc.

1 Press the button to bring up the Station Index.

2 Move the highlight to the station you want.

The program title is displayed at the top of the Station Index. Also,

you’ll hear the audio and see the video (in the background) of each

program, as they are highlighted.

The table below lists the various ways in which you can move

around in the Station Index.

3 Press the button to tune to the program that’s highlighted.

Moving Around

In the Station Index

To Do This ... Use This Button

Go to other stations in the guide, one

station at a time

SAT-A2: Move the joystick in any

direction

SAT-B2: Press the

buttons

You can also change the look of the Station

Index by pressing the DISPLAY button. See

“Using the DISPLAY Feature” on page 44.

Go to other stations in the Station

Index, one “page” at a time

Press the PAGE (CH+) and

PAGE (CH-) buttons

Go to a station directly

Press the 0-9 buttons and press

ENTER (to specify the station

number)

Return to the last station you were

watching

Press the EXIT button

Your Station Index may not look

exactly like this. The stations

displayed depend on the

programming you’ve ordered.

206

STATION INDEX Sports Center

207 208 209 211 212 215

216 220 222 224 225 226 227

229 230 232 233 235 236 240

DISC TLC

Chapter 3: Connecting Your System 11

Chapter 3

Connecting Your System

Read this chapter to set up your DSS receiver for the first time, or to

add or remove audio or video components connected to your system.

Overview

You can connect the DSS receiver in a variety of configurations. The

answers to the following questions will determine how you hook up

and operate your DSS receiver. For example:

Do you have cable TV or a broadcast (terrestrial) TV antenna?

What type of connectors do your TV and VCR have: S-VIDEO,

A/V (RCA-type), or RF coaxial?

Do you plan to integrate your DSS receiver with your audio or

video system?

General Recommendations

Detailed hookup instructions are provided on the pages that follow.

For optimum audio and video performance, follow these general

recommendations as much as possible when hooking up your

components:

If you have an audio or audio/video system, consider integrating

the DSS receiver into a home entertainment configuration to take

advantage of your hi-fi system’s audio capabilities.

If your TV has an S-VIDEO jack, use it to connect your TV to the

DSS receiver. An S-Video connection provides a better picture than

RCA-type video or RF connections.

If your TV does not have an S-VIDEO jack, use your TV’s A/V

connectors to connect your components. An A/V connection

provides a better picture and audio when compared to an RF

connection.

If you have other Sony components that include CONTROL-S

jacks, you can connect these components via their CONTROL-S

jacks in order to pass remote control signals between the DSS

receiver and these components. This allows you to hide

components behind cabinet doors.

If you have a Sony TV that has the S-Link feature, you can connect

it to the DSS receiver’s S-LINK connector to simplify the operation

of your system. Using S-Link, when you turn on the DSS receiver

with the TV’s remote control, it automatically turns on the TV and

switches the video input to DSS. When you press the SYSTEM OFF

button on the TV’s remote control, it turns off both the TV and the

DSS receiver. (See your TV manual for more details.)

12 Chapter 3: Connecting Your System

TV Only

TV With RF Connector Only

Refer to the illustration below (SAT-A2 receiver is pictured).

1 Connect the RG-6 cable from the satellite antenna’s LNB to the DSS

receiver’s SATELLITE IN jack.

Some TVs label this jack RF IN,

instead of VHF/UHF IN.

2 Connect the DSS receiver’s VHF(SAT)/UHF OUT jack to the TV’s

VHF/UHF IN jack.

Note

A VHF/UHF connection does not provide stereo sound. To receive stereo

sound, you must use an A/V connection (described on page 13).

3 Connect one end of the telephone line cord to the DSS receiver’s

TEL LINE jack. Connect the other end to your home’s modular

telephone outlet.

4 Connect one end of the AC power cord to the DSS receiver’s AC IN

jack. Connect the plug end to an AC outlet.

Optional Connections

If you have a cable input, cable box, or a terrestrial TV antenna,

connect it to the DSS receiver’s VHF/UHF IN jack.

To connect the DSS receiver to your audio system, use audio cables

to connect the DSS receiver to your audio receiver’s AUDIO IN

jacks.

1 2 3 4

SAT-A2 receiver is pictured, but connections

are identical for SAT-B2.

Chapter 3: Connecting Your System 13

TV With A/V Connectors

Refer to the illustration below (SAT-A2 receiver is pictured).

1 Connect the RG-6 cable from the satellite antenna’s LNB to the DSS

receiver’s SATELLITE IN jack.

If your TV has only one AUDIO IN jack,

connect the lower (mono) AUDIO L jack

on the DSS receiver to the TV’s AUDIO

IN jack.

2 Connect the DSS receiver’s A/V jacks to the TV’s A/V IN jacks.

3 Connect one end of the telephone line cord to the DSS receiver’s

TEL LINE jack. Connect the other end to your home’s modular

telephone outlet.

4 Connect one end of the AC power cord to the DSS receiver’s AC IN

jack. Connect the plug end to an AC outlet.

Optional Connections

Some TVs label this jack RF IN,

instead of VHF/UHF IN.

If you have a cable input, cable box, or a terrestrial TV antenna,

connect it to the TV’s VHF/UHF IN jack.

Best Connection: If your TV has an S-VIDEO jack, use an S-VIDEO

cable to connect the DSS receiver’s S-VIDEO jack to the TV’s S-

VIDEO IN jack. This provides the best picture quality. Then use

audio cables to connect one set of the DSS receiver’s audio jacks to

the TV’s AUDIO IN jacks.

To connect the DSS receiver to your audio system, use audio cables

to connect the DSS receiver to your audio receiver’s AUDIO IN

jacks.

1 2 3 4

SAT-A2 receiver is pictured, but connections

are identical for SAT-B2.

14 Chapter 3: Connecting Your System

TV and VCR

Refer to the illustration on the opposite page (SAT-A2 receiver is

pictured).

1 Connect the RG-6 cable from the satellite antenna’s LNB to the DSS

receiver’s SATELLITE IN jack.

2 Complete one of the following to connect the DSS receiver:

Better Connection: Connect the DSS receiver’s A/V jacks to the

A/V IN jacks on the TV and VCR. If your VCR has only one

AUDIO IN jack (monoaural VCR), connect it to the lower

(mono) AUDIO L jack on the DSS receiver.

Some VCRs and TVs label this jack RF

IN, instead of VHF/UHF IN.

Good Connection: Connect the DSS receiver’s VHF(SAT)/UHF

OUT jack to the VCR’s VHF/UHF IN jack.

3 Complete one of the following to connect the VCR to the TV:

Better Connection: If both your TV and VCR have A/V jacks,

connect the VCR’s A/V OUT jacks to the TV’s A/V IN jacks.

Good Connection: If your TV or VCR has only an RF jack,

connect the VCR’s VHF/UHF OUT jack to the TV’s VHF/UHF

IN jack.

4 Connect one end of the telephone line cord to the DSS receiver’s

TEL LINE jack. Connect the other end to your home’s modular

telephone outlet.

5 Connect one end of the AC power cord to the DSS receiver’s AC IN

jack. Connect the plug end to an AC outlet.

Optional Connections

If you have a cable input, cable box, or a terrestrial TV antenna,

connect it to the TV or VCR’s VHF/UHF IN jack.

Best Connection: If your TV has an S-VIDEO jack, use an S-VIDEO

cable to connect the DSS receiver’s S-VIDEO jack to the TV’s

S-VIDEO IN jack. This provides the best picture quality. Then use

audio cables to connect one set of the DSS receiver’s audio jacks to

the TV’s AUDIO IN jacks.

To connect the DSS receiver to your audio system, use audio cables

to connect the DSS receiver to your audio receiver’s AUDIO IN

jacks.

If you are using the VCR Mouse, see page 20 for setup instructions.

Note

If the screen appears fuzzy, the program you are watching may be protected by

Macrovision. Turn the VCR off to improve the picture quality.

Chapter 3: Connecting Your System 15

1 2

2 4

SAT-A2 receiver is pictured, but connections

are identical for SAT-B2.

16 Chapter 3: Connecting Your System

Hi-Fi TV, Hi-Fi VCR, Audio Receiver (SAT-A2 Only)

Refer to the illustration on the opposite page.

1 Connect the RG-6 cable from the satellite antenna’s LNB to the DSS

receiver’s SATELLITE IN jack.

2 Connect the DSS receiver’s audio OUT jacks to the audio receiver’s

audio IN jacks.

3 Connect the DSS receiver’s AV jacks to the A/V IN jacks on the TV.

4 Complete one of the following to connect the DSS receiver to the

VCR:

Better Connection: Connect the DSS receiver’s A/V jacks to the

A/V IN jacks on the VCR.

Some VCRs and TVs label this jack RF

IN, instead of VHF/UHF IN.

Good Connection: Connect the DSS receiver’s VHF(SAT)/UHF

OUT jack to the VCR’s VHF/UHF IN jack.

5 Complete one of the following to connect the VCR to the TV:

Better Connection: If both your TV and VCR have A/V jacks,

connect the VCR’s A/V OUT jacks to the TV’s A/V IN jacks.

Good Connection: If your TV or VCR has only an RF jack,

connect the VCR’s VHF/UHF OUT jack to the TV’s VHF/UHF

IN jack.

6 Connect one end of the telephone line cord to the DSS receiver’s

TEL LINE jack. Connect the other end to your home’s modular

telephone outlet.

7 Connect one end of the AC power cord to the DSS receiver’s AC IN

jack. Connect the plug end to an AC outlet.

Optional Connections

If you have a cable input, cable box, or a terrestrial TV antenna,

connect it the VCR’s VHF/UHF IN jack.

Best Connection: If your TV has an S-VIDEO jack, use an S-VIDEO

cable to connect the DSS receiver’s S-VIDEO jack to the TV’s

S-VIDEO IN jack. This provides the best picture quality. Then use

audio cables to connect one set of the DSS receiver’s audio jacks to

the audio receiver’s AUDIO IN jacks.

If you are using the VCR Mouse, see page 20 for setup instructions.

Note

If the screen appears fuzzy, the program you are watching may be protected by

Macrovision. Turn the VCR off to improve the picture quality.

Chapter 3: Connecting Your System 17

4 6

Note

SAT-A2 receiver is pictured, but

connections are identical for SAT-B2.

18 Chapter 3: Connecting Your System

Home Entertainment System

(Hi-Fi TV, Hi-Fi VCR, Audio/Video Receiver)

Refer to the illustration on the opposite page (SAT-A2 receiver is

pictured).

1 Connect the RG-6 cable from the satellite antenna’s LNB to the DSS

receiver’s SATELLITE IN jack.

2 Connect the DSS receiver’s A/V jacks to the VCR and A/V

receiver’s A/V IN jacks.

3 Connect the VCR’s A/V OUT jacks to one set of the A/V receiver’s

A/V IN jacks.

4 Connect the A/V receiver’s MONITOR OUT jack to the TV’s

VIDEO IN jack.

5 Connect one end of the telephone line cord to the DSS receiver’s

TEL LINE jack. Connect the other end to your home’s modular

telephone outlet.

6 Connect one end of the AC power cord to the DSS receiver’s AC IN

jack. Connect the plug end to an AC outlet.

Optional Connections

Some VCRs label this jack RF IN,

instead of VHF/UHF IN.

If you have a cable input, cable box, or a terrestrial TV antenna,

connect it to the VCR’s VHF/UHF IN jack.

Best Connection: If your A/V receiver has an S-VIDEO jack, use an

S-VIDEO cable to connect the DSS receiver’s S-VIDEO jack to the

A/V receiver’s S-VIDEO IN jack. Then connect an S-VIDEO cable

from the A/V receiver to the TV’s S-VIDEO IN jack. This provides

the best picture quality. Then use audio cables to connect one set of

the DSS receiver’s audio jacks to the A/V receiver’s AUDIO IN

jacks.

If you are using the VCR Mouse, see page 20 for setup instructions.

Note

If the screen appears fuzzy, the program you are watching may be protected by

Macrovision. Turn the VCR off to improve the picture quality.

In this configuration, the A/V receiver must be turned on in order to pass the

video signals through to your TV.

Chapter 3: Connecting Your System 19

1 2 6

SAT-A2 receiver is pictured, but connections

are identical for SAT-B2.

20 Chapter 3: Connecting Your System

Connecting the VCR Mouse

SAT-A2 receiver is pictured, but

connections are identical for SAT-B2.

The VCR Mouse works with the DSS receiver’s Timer function to

automatically start and stop the recording function of your VCR.

1 Connect the VCR Mouse to the DSS receiver’s VCR MOUSE/

CONTROL S OUT jack. Then place the VCR Mouse on top of and

slightly overhanging the front

of the VCR. For best results, place

the VCR Mouse directly above the VCR’s IR receiving area.

2 Find the three-digit code number for your VCR in the table below.

If more than one code number is listed, use the number listed first

to complete step 3.

3 Using the buttons on the VCR Mouse: 1) Press the SET button,

2) Enter the three-digit code number, 3) Press the ENTER button.

If the VCR Mouse doesn’t seem to be

working correctly, first check that the

VCR Mouse is positioned directly above

the VCR’s IR receiving area. If it’s still not

working, try this procedure again using

the other codes listed for your VCR. For

more troubleshooting information, see

page 90.

4 To check that the code is correct, press the 1 button on the VCR

Mouse. If the VCR turns on and off each time you press 1, the code

number is correct.

To use the VCR Mouse:

1) Set the DSS Timer (page 38), 2) Turn on the VCR and set the VCR’s

line input to the DSS receiver, 3) Insert a tape, 4) Turn off the VCR.

Manufacturer Code Manufacturer Code Manufacturer Code

Sony* 301, 302, 303 Hitachi 304, 305 Samsung 313, 321, 322

Bell & Howell 343 JVC 314 Scott 312

Daewoo 341 Magnavox 308, 309, 310 Sharp 327, 328

Emerson 316, 317, 318, 319, 320 Mitsubishi 323, 324, 325, 326 Shintom 315

Fisher 330, 333, 334, 335 NEC 336, 337 Symphonic 338

General Electric 304, 329 Panasonic 306, 307 Teknica 338, 342

Go-Video 339, 340 Philips 310 Toshiba 311

Goldstar 332 RCA 305 Zenith 331

*Code 301 is the default code for Sony VHS VCRs; for Sony 8mm VCRs, use code 302; for Sony Beta, ED VCRs, use code 303.

Page is loading ...

Sony SAT-A2/ SAT-B2 Digital Satellite Receiver User manual

Brand: Sony

Model: SAT-A2/ SAT-B2 Digital Satellite Receiver

Category: LED TVs

Type: User manual

Download PDF

report

Sony SAT-A2/ SAT-B2 Digital Satellite Receiver User manual

Sony SAT-A2/ SAT-B2 Digital Satellite Receiver User manual

Related papers

Other documents