Haier 42EP25BAT User manual

Category
LCD TVs
Type
User manual
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
PLASMA TV
OWNER S MANUAL'
MODEL :42EP25BAT
42EP25SAT
42HP25BAT
42HP25SAT
50HP25BAT
S
2 PLASMA TV
THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT
INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT
WITH ANY INSIDE PART OF THIS PRODUCT.
WARNING : To reduce the risk of electric shock do not remove cover or back.
No user-serviceable parts inside refer service to qualified service personnel.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, use and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However ,there is no
guarantee that interference with not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encourage to try to correct the interference by one or
more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may be not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite
cores must be used when connecting this plasma display to video equipment; and maintain
at least 40cm spacing to other peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
RISK ELECTRIC SHOOK
DO NOT OPEN
WARNING
Safety of operators has been taken into consideration at the design and manufacture
phase, but inappropriate operation may cause electric shock or fire. To prevent the product
from being damaged, the following rules should be observed for the installation, use and
maintenance of th product. Read the following safety instruction before starting the operation.
The User Manual uses the following symbols to ensure a safe operation and prevent
any damage to operators or properties:
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
FCC STATEMENT
Owner s Manual 3
IMPORTANT SAFETY INSTRUCTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the following:
1)Save these Instructions ---the safety and operating instructions should be
retained for future reference.
2)All warning on the appliance and in the operating instructions should be followed.
3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use only dry cloth for cleaning.
4)Attachments ---do not use attachments not recommended by the manufacturer
as they may cause hazards.
5)Water and moisture -- do not place this product near water, for example, near a
bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
6)Accessories ---do not place this unit on an unstable cart, stand, tripod, bracket,
or table. Use only with a cart, stand, tripod, bracket, or table recommend by the
manufacture, or sold with the unit.
7)Ventilation ---Slots and openings in the cabinets and the back or bottom are
provided for ventilation. These openings must not be blocked. In a built in
installation such a bookcase or rack do not install product unless proper ventilation
is provided.
8)Power Source ---this TV should be operated only from the type of power source
indicated on the rating label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. To prevent electric shock, ensure
the grounding pin on the AC cord power plug is securely connected.
10)Power cord protection ---Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them. Pay
particular attention to cords or plugs, convenience receptacle, and the point where
they exit from the appliance.
11)Lighting precaution ---for added protection for this product during a lighting
storm or when it is left unattended for long period of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the
product due to lighting and power line surges.
12)Never push objects of any kind into this product through openings as they may
touch dangerous voltage point or short out parts that could result in a fire or electric
shock. Avoid spilling liquid of any kind on the product.
13)Servicing ---do not attempt to service the product by yourself, as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to authorized service personnel.
14)Unplug this unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b.If liquid has been spilled, or objects have been fallen into the unit.
c.If the unit has been exposed to rain or water.
d.If the unit does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions, as
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the unit to its normal
operation.
e.If the unit has been dropped or damaged in any way.
f.When the unit exhibits a distinct change in performance; this indicates a need
for service.
15)Heat --- The product should be situated away heat source such as radiators, heat
registers, stoves, or other products (Including amplifiers) that product heat.
16)Overloading ---Do not overload wall outlets and extension cord as this can result
in a risk of fire or electric shock.
SAVE THESE INSTRUCTIONS
Thank you for using our Haier product. This easy-to-use manual will guide you in
getting the best use of your product. Remember to record the model and serial
number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
4 PLASMA TV
Contents
Introduction
Owner s Manual 5
War nin g . . . . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .
Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Introduction
Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ... ... ... ..
Connection Options . . . . . . . . . . . . . . . . . . . . . .............
Universal Remote Controller . ............ . . . . . . . . ......
Installation
Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ... ... ..
Install the speaker..................................................
Install the stand.....................................................
Antenna Connection . . . . . . . . . . ..............................
VCR Connection. . . . . . . . . . . . . . . . . . . . ................. ..
External A/V Source Setup . . . . .. . . . . ......................
DVD Connection . . . . . ...... . . . . . . . . . . . . . ................
DTV Connection.....................................................
Digital Audio Output . . . . . . . . . . . . . . . . . . . . ..............
PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................
Monitor Out Setup . . . . . . . . . . . . . . . . . . . . ............... .
HDM I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... ... ... ... ... .
Cable sample.........................................................
Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .
Pow er so urc e.. ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...
Choose the Menu Language . . . . ..... .......................
Choose the input source.........................................
Channel Menu
Automatic Scan. . . . . . . . . . . . . ............................. . .
Man ual S can . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . .. .
Fine tune................................................................
Edi t Pro gra m.. ... ... ... ... . . . . . . . . . . . . . . . . . . . . . . . . . ..
S . . . . . ........... ............ . . ..
S . . .............. . . . ............ . . ..
Mute .............. . . . ............................................ . . ..
Video Menu
Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . ... . .. . . ..
Audio Menu
SAP Broadcasts Setup............................................
elect the desired program
elect the desired sound
How to select picture modes.....................................
How to customize your own picture status .................
How to select audio modes......................................
How to customize your own audio status ..................
Timer Menu
Function Menu
Closed Captions.....................................................
CC mode...............................................................
........................................................
DTV Caption..........................................................
DTV Caption Style..................................................
.........................................................
...........................................................
..................................................
Menu
Screen Setup for PC mode......................................
Lock Menu
Parental Control rating and categories.......................
Others Functions
EPG (Electronic Program Guide) . . . . . . . . . . . . .........
Bri ef In fo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ... . .
Veiwing Picture- in- Picture
Maintenance . . ... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty ................................................................
Date /Time setting...................................................
Timer on setting......................................................
Timer off setting......................................................
Sleep Timer setting.................................................
Time zone setting...................................................
Daylight Saving setting...........................................
NTSC Caption
OSD Timeout
Blue screen
OSD transparency
Adjust
Quick program view.................................................
.....................................
Setting up your remote control ..................................
Remote Control Codes ............................................
Manufactured under license from Dobly Laboratories. "Dobly" and the
double-D symbol are trademarks of Dobly Laboratories. Confidential
unpublished works.
Copyright 1992-1997 Dolby Laboratories. All right reserved.
MENUVOL+
CH+
CH-
INPUT
EXIT
VOL-
Front panel controls
-This is a simplified representation of front panel.
-Here shown may be somewhat different from your TV.
1.EXIT
2.INPUT:
.CH(+/-) Program plus and minus, menu
options
4.VOL(+/-) Volume increase and decrease,
menu reset and entry
5.MENU Menu display
6.
. Remote control signal receive window.
8.Remote Indicator In red when standby
mode, in blue when display.
clears all on-screen displays and
returns to TV viewing from any menu.
all input source display and OK
confirm.
3
POWER : Power on or off button.
7
Controls
42EP25BAT
Introduction
6 PLASMA TV
42HP25BAT
50HP25BAT
EXIT INPUT MENU
2
5 6
7
8
4
1
3
CH-
1.VIDEO input
2.L-AUDIO-R left and right audio input.
3. EXIT: clears all on-screen displays and returns to
TV viewing from any menu.
4. INPUT: Source input select.
5.CH- /CH+: Program plus and minus, menu options.
6. VOL-/VOL+: Volume increase and decrease, menu
reset and entry
7.MENU: Menu display
8.Power: Power on or off button.
CH+ VOL- VOL+
42EP25SAT 42HP25SAT
Back panel controls
Connection Options
42EP25BAT
DVI Audio Input
Connect the audio out from
the external device, used
while using a DVI to HDMI
connector.
Power Cord Socket
This TV operates on AC power.
The voltage is indicated on the
Specifications page. Never attempt
to operate the TV on DC power
PC
Audio In
PrPb
Y
DVI Audio In
AC IN
DVD/DTV Input
(Component )
Connect a component
video/audio device to
these jacks.
Earphone jack:
Earphone audio
output terminal.
Audio input
for linking PC audio
output terminals.
PC VIDEO Input
Connect the monitor
output connector from
a PC to the jack
Antenna Input
Connect cable or
antenna signals to
the TV, either directly
or through your
cable box.
HDMI
Optical
YPbPr
Audio In
LR
Headphone
out
S-Video
S-Video Input
Connect SVideo
out from
an S-VIDEO
device to the S-VIDEO
input.
Digital Audio Output
Connect digital audio
from various types of
equipment. Note: In
standby mode,
these ports will not
work.
CVBS
S-video/CVBS
Audio In
LR
RL V
AV OUT
R INPUT
F
HDMI/DVI
connect a
DVI(Video)
signal to
HDMI/DVI.
DVI Audio Input
Connect the audio out from
the external device, used
while using a DVI to HDMI
connector.
Power Cord Socket
This TV operates on AC power.
The voltage is indicated on the
Specifications page. Never attempt
to operate the TV on DC power
PC
Audio In
PrPb
Y
DVI Audio In
AC IN
DVD/DTV Input
(Component )
Connect a component
video/audio device to
these jacks.
Earphone jack:
Earphone audio
output terminal.
Audio input
for linking PC audio
output terminals.
PC VIDEO Input
Connect the monitor
output connector from
a PC to the jack
Antenna Input
Connect cable or
antenna signals to
the TV, either directly
or through your
cable box.
HDMI
Optical
YPbPr
Audio In
LR
Headphone
out
S-video
S-Video Input
Connect S-Video
out from
an S-VIDEO
device to the S-VIDEO
input.
Digital Audio Output
Connect digital audio
from various types of
equipment. Note: In
standby mode,
these ports will not
work.
CVBS
S-video/CVBS
Audio In
LR
RL V
AV OUT
R INPUT
F
HDMI/DVI
connect a
DVI(Video)
signal to
HDMI/DVI.
Introduction
Owner s Manual 7
AUDIO OUT
Optical Audio Output
Optical Audio Output
AUDIO Input
connect to hear
stereo sound from an
external device.
VIDEO Input
Connects the video
signal from a
video device.
AUDIO/VIDEO
output
AUDIO output
AUDIO Input
connect to hear
stereo sound from an
external device.
VIDEO Input
Connects the video
signal from a
video device.
AUDIO/VIDEO
output
42HP25BAT
50HP25BAT
42EP25SAT 42HP25SAT
SELECT
CH.LIST
FAV.LIST
AUDIO LIST
PIP SWAP
AUDIO SWAP
POSITION
CC
P .MODE
S.MODE
FREEZE
E
N
U
UIDE
NPUT
INFO
E
X
IT
R
A
C
S
A
P
S
L
E
E
P
VOL+
CH+
Q.VIEW
OK
VO
L
-
CH-
POWER
Turns your TV or any other programmed
equipment on or off, depending on mode.
- The remote controller cannot be operated unless the batteries are properly loaded.
Function introduction
- When using the remote control, aim it at the remote control sensor on the TV.
SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog
mode. Change the audio language in DTV mode.
Introduction
8 PLASMA TV
FAVORITE
Open the favorite channel list. Select the subchannel
THUMBSTICK
(Up/Down/Left/Right/OK)
Allows you to navigate the on-screen menus and adjust
the system settings to your preference.
CHANNEL UP/DOWN
Selects available channels
P.MODE
Selects the picture appropriate
for the program's character.
FREEZE
Freezes the currently-viewed picture, but audio continues.
Press FREEZE button again to resume the normal picture.
ARC
(Aspect Ratio Control)
Changes the aspect ratio.
It is not available under PIP mode.
It is available under PBP mode.
S.MODE
Selects the sound appropriate for the program's
character.
VOLUME UP/DOWN
Increases/decreases the sound level.
Numeric buttons
press to change the channel.
EXIT
Clears all on-screen displays and
returns toTV viewing from any menu.
INPUT
show the input source mode.
MUTE
Switches the sound on or off
CC(closed caption)
Select a closed caption:
CC MUTE, CC ON, CC OFF.
GUIDE
Shows program schedule.
INFO
When you watch the TV, press the key, the information
displays on bottom of the screen.
MENU
Brings up the main menu to the screen.
PIP function buttons
PIP:Selects PIP, PBP and main Window;
SWAP:In PIP and PBP mode, swap the
main and sub window;
AUDIO SWAP: In PIP and PBP mode,
swap the audio of main and sub window;
PIP position: To select sub picture
position for PIP.
SLEEP button
Displays the Sleep Timer option.
Q.VIEW
Switch the current channel to the last channel
you have viewed, or switch the other source to TV.
CH.LIST
Open the channel list.
Universal Remote Controller
TV DVD VCR SETBOX CABLE AUDIO
Press the SELECT button repeatedly to select one of the
system modes in which the remote control can be used.
When the desired device is selected, the corresponding
LED lights on 5seconds.
VCR/DVD Functions
Control some video cassette recorders or DVD players.
/ Rewind / Fast
/ backward /Forward
Stop
Play/Pause
REC
AUDIO.LIST
Open the audio channellist.
- button
Press to select additional channels
(digital and analog)
being broadcast by the same station.
For example, to select channel
“54-3”, press “54”, then press “-” and “3”.
LIGHT
Press the light button, white LED will be ON, release
this key, white LED will be OFF.
Speaker unit(X2)
Connection cord
(
Owner s Manual 9
Accessories
Remote controller
Owner`s manual
Alkaline battery(AAA) 2
Power cable
SELECT
CH.LIST
FAV.LIST
AUDIO LIST
PIP SWAP
AUDIO SWAP
POSITION
CC
P.MODE
S.MODE
FREEZE
E
N
U
U
I
D
E
N
P
U
T
I
N
F
O
E
X
I
T
R
A
C
S
A
P
S
L
E
E
P
VOL+
CH+
Q.VIEW
OK
VO
L
-
CH-
PLASMA TV
OWNER S MANUAL'
42EP25BAT
42HP25BAT
Remote controller
Owner`s manual
Alkaline battery(AAA) 2
Power cable
SELECT
CH.LIST
FAV.LIST
AUDIO LIST
PIP SWAP
AUDIO SWA P
POSITION
CC
P.MODE
S.MODE
FREEZE
E
N
U
U
I
D
E
N
P
U
T
I
N
F
O
E
X
I
T
R
A
C
S
A
P
S
L
E
E
P
VOL+
CH+
Q.VIEW
OK
VO
L
-
CH-
PLASMA TV
OWNER S MANUAL'
50HP25BAT
M4X12 x8Screws
Standx1
Brace pole x2
M5X16 x4Screws
42EP25SAT
42HP25SAT
Íâ¹ÒÑïÉùÆ÷ʹÓÃ˵Ã÷
Before turning on the PDP , ensure you have connected the line between the speaker and the PDP
1 Face the PDP screen upside down on a clean blanket or a bracket and pay attention not to indent the casing. (See figure),
lay the two speaker aside of the PDP.
3 Fix the speaker to the PDP with the screws 4-ST 4X16 .
2 Insert the pothook to the faucet of the PDP screen .
Connect the speaker to the speaker terminal of plasma screen:
Press the speaker terminal and insert the connecting cable into the terminal slot.
Release the speaker terminal and ensure that the white connecting cable is inserted in the terminal slot marked red and black connecting
cable is inserted in the black terminal slot, and that anode and cathode poles are correctly connected. (See Figure )
The left speaker
The right speaker
L R
EXT SPEAKER
Install the Speakers(42EP25 AT/42HP25 AT/ )B B 42EP25SAT/42HP25SAT
10 PLASMA TV
25.400
\U+2592\U+255A\U+2514\U+00B2
25.400
\U+2592\U+255A\U+2514\U+00B2
Install the Stand
Face the PDP screen upside down on a clean blanket or the bracket and pay attention not to indent the casing.
Lay down the stand and put it to responding position of the PDP screen ,and make sure the brace pole towards the hole of the PDP .
Fix 2 PDP brace pole to the PDP on the back of the plasma display with 4 M5X16 screws.
Install the Stand to the PDP
Insert the supporting bracket with 8 M4x12 screws to
the installation holes on the bottom of the soleplate.
Fasten the Supporting bracket and the Soleplate
as shown in figure.
Owner s Manual 11
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an
outdoor antenna .In different places, the suitable antenna type and position are different.
External Equipment Connections
Antenna Connection
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
VHF Antenna
UHF Antenna
Turn clockwise to tighten.
RF Coaxial Wire (75 ohm)
Bronze Wire
Be careful not to bend the bronze wire when
connecting the antenna.
Bronze Wire
To improve the picture quality in a poor signal area,
please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV`s, install a 2-
Way Signal Splitter in the connections.
If the antenna is not installed properly, contact your dealer
for assistance.
Installation
GROUNDING
Ensure that you connect the earth ground wire to prevent possible electric
shock. If grounding methods are not possible, have a qualified electrician
install a separate circuit breaker. Do not try to ground the unit by connecting
it to telephone wires, lightening rods, or gas pipes.
- The TV can be installed in various ways such as on a wall, or on a desktop etc.
- The TV is designed to be mounted horizontally.
12 PLASMA TV
VCR connection
NOTE: All cables shown are not included with the TV.
There are several ways to connect your television, depending on the components you want to connect
and the quality of the signal you want to achieve. The following are examples of some ways to connect
your TV. Choose the connection which is best for you.
External Equipment Connections
Choose Your Connection
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
Connection Option 1
Set VCR output switch to channel 3 or 4 and
then tune the TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
shown in the figure.
When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
If you connect an S-VIDEO output from VCR to
the S-VIDEO input, the picture quality is
improved; compared to connecting a regular
VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s
manual.)
3. Select the input source with using the
INPUT button on the remote control, and
then press / button to select the source,
press the button to confirm.
S-Video
CVBS
S-Video/CVBS
Audio In
LR
RL V
AV OUT
R INPUT
F
Installation
Owner s Manual 13
Pr Pb
Y
DVI Audio IN
YPbPr
Audio In
LR
Headphone
out
S-Video
CVBS
S-Video/CVBS
Audio In
LR
How to connect
1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb,
Pr jacks on the TV and connect the DVD audio outputs to the
YPbPr Audio IN jacks on the TV, as shown in the figure.
2. If your DVD only has an S-VIDEO output jack, connect this
to the S-VIDEO input on the TV. as shown in the figure.
NOTE: If your DVD player does not have component video
output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select YPbPr
mode.
3. Press Play button on external equipment for program play.
4. Refer to the DVD player's manual for operating instructions.
DVD connection
External Equipment Connections
How to connect
Connect the audio and video cables from the external equipment's
output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the input source with using the INPUT button on
the remote control.
2. Press the / button to select the desired source.
3. Press the ok button to confirm
2. Operate the corresponding external equipment.
External A/V Source Setup
Video Game Set
Camcorder
Component Input ports
To get better picture quality, connect a DVD player to the component
input ports as shown below.
S-Video
CVBS
S-Video/CVBS
Audio In
LR
RL V
AV OUT
R INPUT
F
Installation
Component ports
on the TV
Video output ports
on DVD player
Y Pb Pr
Y Pb Pr
Y B-Y R-Y
Y Cb Cr
Y P P
BR
14 PLASMA TV
PC
Audio In
Pr Pb
Y
DVI Audio IN
HDMI
Optical
YPbPr
Audio In
LR
Headphone
out
Digital Set-top Box
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital
signals from a digital set-top box or other digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
How to connect
Use the TV`s (Y, PB, PR) , VGA or HDMI
jack for video connections, depending on
your set-top box connector. Then, make
the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner`s
manual for the digital set-top box.)
2. Use INPUT on the remote control to select
YPbPr, VGA,or HDMI source.
Send the TV`s audio to external audio equipment (stereo system) via
the Digital Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Digital Audio
(Optical) Output port.
2. Connect the other end of the optical cable to the digital audio (optical)
input on the audio equipment.
See the external audio equipment instruction manual for operation.
Note: When connecting with external audio equipments, such as
amplifers or speakers, please turn the TV speakers off.
Digital Audio Output
Caution: Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
External Equipment Connections
DTV connection
HDMI
Optical
YPbPr
Audio In
LR
Headphone
out
Installation
Signal
480i
480p
720p
1080i
YPbPr
Yes
Yes
Yes
Yes
HDMI/DVI
Yes
Yes
Yes
Yes
Owner s Manual 15
PC
AUDIO
IN
Pr Pb
Y
DVI
Audio IN
HDMI
How to connect
1. To get the best picture quality, adjust the PC graphics card to (1024
2. Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC connector.
If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherVGA r DVI IN to
display the PC on the TV.
If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe DVI; (the other mode is
set to Plug and Play automatically by the TV.)
3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.
How to use
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Use INPUT on the remote control to select VGA or HDMI source.
4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode.
If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and
contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic
card or consult the manufacturer of the PC graphic card.
NOTES:
1 Use a DVI cable.
2 Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the
screen.
3 The synchronization input form for Horizontal and Vertical frequencies is separate.
x768).
IN o
r VGA or
PC connection
Resolution
Frame
frequency
(Hz)
VGA
SVGA
XGA
640*480 60Hz
800*600 60Hz/75Hz
1024*768
60Hz
Mode
Resolution
External Equipment Connections
Installation
75Hz
85Hz
16 PLASMA TV
External Equipment Connections
The TV has a special signal output capability which allows you to
hook up a second TV or monitor.
Connect the second TV or monitor to the TV`s AV OUT.
See the Operating Manual of the second TV or monitor for further
details regarding that device`s input settings.
Notes:
YPbPr, VGA, HDMI,DTV input sources
cannot be used for Monitor out.
When connecting with external audio equipments, such as amplifers
or speakers, please turn the TV speakers off.
Monitor Out Setup
AUDIO OUT
L R
RL V
AV OUT
R INPUT
F
Installation
Owner s Manual 17
TM
- HDMI , the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing."
- This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).
- This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolution.
- When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output
resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto HDMI/DVI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's
output resolution to 1024x768, 60Hz.
- If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes
both video and audio.
- If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.
<When the source device(DVD player or Set Top Box) supports HDMI>
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).
2. No separated audio connection is necessary.
How To Use
- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
- Select HDMI input source in input source option of Select Main source menu.
<When the source device(DVD player or Set Top Box) supports DVI>
How To Connect
1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).
2. A separated audio connection is necessary.
3.If the source device has an analog audio output connector, connect the source device audio output to DVI Audio In port located on the
left side of HDMI port.
How To Use
- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto DVI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
- Press the INPUT button to select HDMI input source in input source option of Select Main source menu.
HDMI
Installation
18 PLASMA TV
Cable sample
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable
(Stereo to RCA type)
(not supplied with the product)
Installation
Owner s Manual 19
YPbPr
Audio In
LR
Headphone
out
S-VIDEO
Power source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for
operation on AC. Insert the AC cord plug into
a standard polarized AC outlet.
NOTES:
Never connect the AC line cord plug to other
than the specified voltage. Use the
attached power cord only.
If the polarized AC cord does not fit into a non-
polarized AC outlet, do not attempt to file or cut
the blade. It is the user`s responsibility to have
an electrician replace the obsolete outlet.
If you cause a static discharge when touching
the unit and the unit fails to function, simply
unplug the unit from the AC outlet and plug it
back in. The unit should return to normal operation.
Polarized AC Cord Plug
AC Outlet
Wider Hole
and Blade
You can connect a set of headphones to your set if you wish to watch a
TV programme without disturbing the other people in the room.
Connecting Headphones
External Equipment Connections
Note
Prolonged use of headphones at a high volume
may damage your hearing.
You will not receive sound from the speakers
when you connect headphones to the system.
Plug a set of headphones into the 3.5mm
mini-jack socket on the rear panel of the set.
Installation
20 PLASMA TV
1 / 1

Haier 42EP25BAT User manual

Category
LCD TVs
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document