SMART Technologies 99-00964-20 User manual

Category
Data projectors
Type
User manual

This manual is also suitable for

Configuration and User’s Guide
Parts Kit for SMART Board™ 560 and 580
Interactive Whiteboards and UF55 Projectors
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Trademark Notice
SMART Board, smarttech and the SMART logo are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries.
All other third-party product and company names may be the trademarks of their respective owners.
Copyright Notice
© 2009 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system
or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is
subject to change without notice and does not represent a commitment on the part of SMART.
Patent No. US5448263; US6141000; US6320597; US6326954; US6326954; US6337681; US6540366; US6741267; US6747636; US7151533; US7184030;
US7289113 and CA2058219. Other patents pending.
Printed in Canada. 04/2009
If you register your SMART product, we’ll notify you of new features and
software upgrades.
Register online at
www.smarttech.com/registration.
Keep the following information available, in case you need to contact
Technical Support:
Serial Number
Date of Purchase
Registration Benefits
99-00964-20 A0 Important Information i
Important Information
Read This Section First
NOTE: If you own a SMART product other than a parts kit for SMART Board 560 and 580 interactive whiteboards
and UF55 projectors, refer to the installation guide that came with your product for relevant warnings and
maintenance instructions.
Before you install and use your parts kit for SMART Board 560 and 580 interactive whiteboards and UF55
projectors, read and understand the safety warnings and precautions in this user’s guide, the Parts Kit for
SMART Board 560 and 580 Interactive Whiteboards and UF55 Projectors (
document 134836) and the warnings
document. These safety warnings and precautions describe the safe and correct operation of your SMART
Board interactive whiteboard system and its accessories, helping you to prevent injuries and equipment damage.
Always ensure that your interactive whiteboard system is being used correctly.
The UF55 projector is currently designed to work only with certain SMART Board interactive whiteboard models.
Contact your
authorized SMART reseller for more information.
ii Important Information 99-00964-20 A0
Safety Warnings
WARNING
If the lamp has shattered or burst, call an authorized SMART reseller for instructions.
Do not attempt to replace the lamp. Do not touch the glass fr
agments because they might
cause injury. Leave and then ventilate the area where the lamp shattered or burst. Wash
your hands thoroughly if you have come into contact with lamp debris. Thoroughly clean the
area around the projector, and discard any edible items placed in that area because they
might be contaminated.
The lamp used in the UF55 projector contains mer
cury. Recycle or dispose of it as
hazardous waste, in accordance with local regulations.
Use only replacement lamps approved by S
MART Technologies. Contact your
authorized SMART reseller for replacement parts.
Turn the projector off and wait 30 minutes for the
lamp to cool completely before removing
the old lamp assembly.
Never replace the lamp assembly with a p
reviously used lamp assembly.
Do not open or disassemble the projector
as this may cause electric shock.
Ensure that any cables extending across the floor to
your SMART product are properly
bundled and marked to prevent a trip hazard.
Make sure that an electrical socket is near t
o your SMART product and remains easily
accessible during use.
Avoid turning off the projector during the lamp ignition
phase as this may lead to premature
lamp failure. Before turning the projector off, keep the lamp on for a minimum of 15 minutes
after turning it on to preserve the lamp life.
This projector detects its own remaining la
mp life. Replace the lamp when lamp life warning
messages appears.
If you continue to use the projector after the replacement message appears, the lamp might
sh
atter or burst, scattering glass throughout the projector head.
When the lamp is approaching the end of its life, t
he message “Lamp is approaching the end
of its useful life in full power operation” appears on the screen. Contact your
authorized SMART reseller or service center to change the lamp as soon as possible.
Remove the projector from the projector’s arm be
fore servicing the lamp. Complete the
procedure described in this document before following the instructions included in your
replacement lamp box.
Do not attempt to service the projector other than performing routine lamp replacement.
Service should be per
formed only by an authorized service provider. Other than the lamp
module, there are no user-serviceable parts inside the unit.
Replacing the lamp in a boom-mounted projector might result in
fall or injury.
Uncovering the lamp while the projector is mounted on a
projector’s arm might lead to
product damage or personal injury from falling pieces of glass if the lamp is broken.
Wear protective eyewear while changing the lamp. Failure to do
so can cause injury or loss
of eyesight if the lamp shatters or bursts.
WARNING
To prevent premature lamp failure or exposure to mercury, always handle the fragile lamp
assembly with care. Use gloves when touching the lamp. Do not touch the lamp with
your fingers.
Failure to follow the installation instructions shipped with
your SMART product could result in
personal injury and damage to the product.
Two people are required to remove and mount the projector and the interactive whiteboard
on a wa
ll because they might be too heavy for one person to maneuver onto their
wall-mounting brackets.
When mounting the projector on a framed wall, you must attach both the mounting bracket
and safety tether
to a stud to safely support the projector’s weight. If you use only drywall
anchors, the drywall can fail, resulting in product damage and possible personal injury.
Do not remove any screws other than those specified in the lamp r
eplacement instructions.
If you remove the bolt supporting the limit strap, the p
rojector’s arm will be free to swing.
Make sure that the bolt is tightened, and never remove it from the unit without supporting the
projector’s arm first.
To reduce the risk of fire or electric shock, do not expose any component of your
SMART
Board interactive whiteboard system to rain or moisture.
Do not climb (or allow children to climb) on any part of
yo
ur wall-mounted SMART Board interactive
whiteboard system.
Climbing on the interactive whiteboard or projector arm
could result in personal injury or product damage.
Do not stare (or allow children to stare) directly into the
beam of light cr
eated by the projector. Instruct children
not to look in the direction of, or stare at, this beam of
light. Encourage users to keep their back to the projector
when working at the interactive whiteboard. Before they
turn to face the audience, users should step sideways,
out of the projector’s beam.
Do not touch the head or lens of the projector because it
ca
n become extremely hot during normal operation.
Cleaning a boom-mounted projector may result in a fall or injury.
Don’t add extra weight or apply pressure to t
he UF55 projector boom, the wall-mounted
interactive whiteboard or its pen tray. SMART Technologies designed the brackets to support
only the weight of the components during normal use.
99-00964-20 A0 Important Information iii
CAUTION
Never operate your projector immediately after moving it from a cold location to a warm
location. When your projector is exposed to such a change in temperature, moisture may
condense on the lens and on crucial internal parts. Allow your projector to reach room
temperature before operation to prevent possible damage to your projector.
At high altitudes, where the air is thin, the projector
’s cooling efficiency is reduced. Set the
projector’s fan mode to High in locations where the altitude is over 6000' (1828.8 m).
Do not place in hot locations, such as nea
r heating equipment. Doing so could cause a
malfunction and shorten the life of the projector.
Before you clean the UF55 projector, put the system into Idle mode by pressing th
e power
button twice on the ECP or remote, and allow the bulb to cool for 30 minutes.
Do not allow liquids or commercial solvents of any kind to flow into the pr
ojector base or
head. Do not use spray cleaners or solvents near any part of the projector, as it may damage
or stain the projector.
Cycling power to the projector repeatedly ca
n lock or damage the interactive whiteboard
system. After you turn off the system, wait at least 15 minutes for cooling before starting the
system.
Do not connect your serial cable directly to the pro
jector’s RS-232 serial interface. The
extended control panel’s (ECP’s) RS-232 serial interface is the only recommended
connection point.
You must connect the USB cable that came with your SMART Board interactive whiteboard
to a computer
that has a USB compliant interface and that bears the USB logo. In addition,
the USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark
and CSA and/or UL Mark(s) for CAS/UL 60950. This is for operating safety and to prevent
damage to the SMART Board interactive whiteboard.
IMPORTANT
Using the UF55 projector near a TV or radio may cause interference to the images or sound.
If this happens, move the TV or radio away from the projector.
If you have peripheral devices that do not use a 4-
pin mini-DIN connector or an RCA
composite video jack, or if your device has an audio connection that does not use RCA
jacks, you may need to purchase third-party adapters.
Wipe the exterior of the projector using a lint-free cloth.
iv Important Information 99-00964-20 A0
99-00964-20 A0 Important Information v
Other Precautions
To ensure operating safety and to prevent product damage, observe the following precautions.
Turn off the SMART product before cleaning it.
Use a soft lint-free cloth moistened with a mild detergent to clean the projector housing.
Don’t use abrasive cleaners, waxes or solvents to clean your SMART product.
Disconnect the power plug from the AC outlet if your SMART product is not being used for a long period
of time.
Don’t block the ventilation slots and openings on the projector.
Don’t place the interactive whiteboard system near any appliance that generates a strong magnetic field.
Don’t place the interactive whiteboard system in direct sunlight.
Don’t set up or use the interactive whiteboard system in an area with excessive levels of dust, dirt, humidity
or smoke.
To reduce the risks associated with leaking batteries:
use only a coin-cell type battery
orient the battery’s plus (+) and minus (-) terminals according to the markings on the remote control
don’t leave the battery in the remote control for an extended period
don’t heat, disassemble, short or recharge the battery or expose it to fire or high temperatures
avoid eye and skin contact if the battery has a leak
dispose of the exhausted battery and product components in accordance with applicable regulations
If the interactive whiteboard system requires replacement parts, make sure that the service technician uses
replacement parts specified by SMART Technologies, or parts with the same characteristics as the original.
vi Important Information 99-00964-20 A0
99-00964-20 A0 Table of Contents vii
Table of Contents
Important Information i
Read This Section First................................................................................................................................... i
Safety Warnings............................................................................................................................................. ii
Other Precautions .......................................................................................................................................... v
Table of Contents vii
About Your UF55 Projector Parts Kit 1
UF55 Projector System Features................................................................................................................... 2
Standard Accessories .................................................................................................................................... 3
Installing Your UF55 Projector Parts Kit 5
Environmental Requirements......................................................................................................................... 6
Choosing a Location for Your SMART Board Interactive Whiteboard System............................................... 7
Adjusting the Image Alignment ...................................................................................................................... 8
Focusing the Image...................................................................................................................................... 14
Connecting Your Interactive Whiteboard System 15
Upgrading Your Version of SMART Board Software .................................................................................... 15
Connecting the Cables to the UF55 Projector.............................................................................................. 16
Using Your Interactive Whiteboard System 23
Turning the System On and Off and Selecting an Input...............................................................................23
After Completing the Installation .................................................................................................................. 24
Using Your UF55 Projector .......................................................................................................................... 24
Maintaining Your UF55 Projector 29
Cleaning Your UF55 Projector ..................................................................................................................... 29
Transporting Your Projector .........................................................................................................................30
Troubleshooting Your Interactive Whiteboard System 31
System Warning Lights ................................................................................................................................ 31
Errors ........................................................................................................................................................... 32
Appendix A: Remotely Managing Your Interactive Whiteboard System 35
Programming Commands for Your SMART Board Interactive Whiteboard
System Settings ........................................................................................................................................... 35
Command Inventory..................................................................................................................................... 38
Appendix B: Replacing Your UF55 Projector Lamp 47
Replacing the Projector Lamp......................................................................................................................47
viii Table of Contents 99-00964-20 A0
Hardware Environmental Compliance 59
Waste Electrical and Electronic Equipment Regulations (WEEE Directive).................................................59
Restriction of Certain Chemicals (REACH Directive) ...................................................................................59
Restriction of Certain Hazardous Substances (RoHS) Directives................................................................59
Batteries .......................................................................................................................................................59
Packaging ....................................................................................................................................................59
China’s Electronic Information Products Regulations ..................................................................................60
U.S. Consumer Product Safety Improvement Act........................................................................................60
Customer Support 61
Online Information and Support ...................................................................................................................61
Training ........................................................................................................................................................61
Technical Support.........................................................................................................................................61
Shipping and Repair Status..........................................................................................................................61
General Inquiries.......................................................................................................................................... 61
Registration ..................................................................................................................................................61
Warranty.......................................................................................................................................................62
Index 61
99-00964-20 A0 About Your UF55 Projector Parts Kit 1
About Your UF55 Projector Parts Kit
Your UF55 projector parts kit enables you to combine the SMART UF55 wall-mounted short-throw projector with
your SMART Board 580 or 560 interactive whiteboard to create a complete interactive whiteboard system.
The following topics describe the features of the components and accessories included in your parts kit.
UF55 Projector System Features (page 2)
Standard Accessories (page 3)
ECP and Cable (page 3)
UF55 Remote Control (page 3)
2 About Your UF55 Projector Parts Kit 99-00964-20 A0
UF55 Projector System Features
The UF55 projector system includes a short-throw projector for use with SMART Board interactive whiteboards,
an extended control panel (ECP) and a sturdy support system for classroom environments. The projector system
has the following features:
A wall-mounted, high-offset SBP-10X (for XGA or UF55) projector engine that uses DLP® technology by
Texas Instruments®, providing Brilliant Color™ performance and quality Gamma 2.2 correction with High
Brightness, Standard and True Color modes
Safety-oriented design that includes a boom support with a controlled-collapse feature
PAL, PAL-N, PAL-M, SECAM, NTSC and NTSC 4.43 video system compatibility
Composite, S-video and VESA RGB with additional interface support for Component YPbPr and
Component YCbCr inputs with proper adapters (not included)
WXGA, QVGA, VGA, SVGA, XGA, SXGA, SXGA+ and UXGA video format compatibility
1024 × 768 resolution
Serial RS-232 interface on the ECP for connecting a room control system
Self-protection timer for a hot re-strike of the projector lamp
Protected cable routing through the projector housing and a cable cover to prevent tampering and clutter
A secure mounting and installation system that includes:
A projector padlock loop
Mounting hardware for solid masonry or framed wall installations
Templates and instructions for positioning the system in a safe manner
99-00964-20 A0 About Your UF55 Projector Parts Kit 3
Standard Accessories
SMART provides the following accessories with your UF55 projector parts kit. If you need to purchase
replacements, contact your
authorized SMART reseller.
ECP and Cable
The interactive whiteboard system’s ECP features connectors for three
inputs and control for four inputs, including the direct HD-DB15 RGB
connection to the projector. Direct inputs supported include:
A single HD-DB15 (RGB) input connector and associated audio
(3.5 mm jack) for RGB or component video and HDTV sources
(YPbPr/YCbCr with proper adapters, not included)
An S-video (4-pin mini-DIN) and associated audio (two RCA jacks)
A composite video (RCA jack) and associated audio (two RCA jacks)
A specialized harness cable provided by SMART allows output to the projector.
UF55 Remote Control
The remote control lets you control the system and set up your UF55 projector.
Use the remote control to access menu options, system information and input
selection options.
4 About Your UF55 Projector Parts Kit 99-00964-20 A0
99-00964-20 A0 Installing Your UF55 Projector Parts Kit 5
Installing Your UF55 Projector Parts Kit
IMPORTANT
The following sections include additional information, optional procedures and tips to consider when you install
your SMART Board interactive whiteboard system with the UF55 projector parts kit.
Environmental Requirements (page 6)
Choosing a Location for Your Interactive Whiteboard System (page 7)
Recommended Heights for Mounting (page 7)
Adjusting the Image Alignment (page 8)
Diagnosing Alignment Errors (page 8)
Performing an Image Alignment (page 9)
Focusing the Image (page 14)
Use the instructions from the UF55 projector boxes to install your parts kit, including the
projector and ECP mounting template. Don’t use the instructions in your SMART Board
interactive whiteboard product box.
6 Installing Your UF55 Projector Parts Kit 99-00964-20 A0
Environmental Requirements
Before installing your UF55 projector parts kit, review the following environmental requirements.
CAUTION
Never operate your projector immediately after moving it from a cold location to a warm
location. When your projector is exposed to such a change in temperature, moisture might
condense on the lens and on crucial internal parts. Allow your projector to reach room
temperature before operation to prevent possible damage to your projector.
At high altitudes, where the air is thin, the projector
’s cooling efficiency is reduced. Set the
projector’s fan mode to High in locations where the altitude is over 6000' (1828.8 m).
Do not place the projector in hot locations, such as near
heating equipment. Doing so could
cause a malfunction and shorten the life of the projector.
Environmental Requirement Parameter
Operating Temperature
41°F to 95°F (5°C to 35°C) from sea level to an altitude
up to 6000' (0 m to 1828.8 m)
41°F to 86°F (5°C to 30°C) from 6000' to 9800'
(1828.8 m to 2987 m)
Storage Temperature -40°F to 122°F (-40°C to 50°C)
Humidity 30% to 70% relative humidity, non-condensing
Water and Fluid Resistance
Intended for indoor use. SMART Board interactive whiteboard
systems do not
meet any salt-spray or water ingress
requirements.
Don’t pour or spray liquids directly on interactive whiteboard,
the
projector or any of its sub-components. These liquids might
get into areas where they could damage sensitive electronic
components.
Dust and Scratching
For use in office and classroom
environments
Not for industrial use, where heavy dust and pollutants can
cause malfunctions or imp
aired operation
Designed for pollution degree 1 (P1) as per EN61558-1, which
is
defined as “No pollution or only dry non-conductive pollution”
Electrostatic Discharge (ESD)
EN61000-4-2 severity level 4 for direct and indirect ESD
No malfunction or damage up to 8 kV (both polarities)
with a 330 ohm, 150 pF probe (air discharge)
Unmated connectors meet no malfunction or damage
up to 4 kV for direct (contact) discharge.
Conducted and Radiated Emissions EN55022/CISPR 22, Class A
99-00964-20 A0 Installing Your UF55 Projector Parts Kit 7
Choosing a Location for Your SMART Board Interactive Whiteboard System
Choose a location for your SMART Board interactive whiteboard system that’s far from bright light sources and
direct sunlight such as a window or overhead lighting. Bright light sources can cause distracting shadows on the
interactive whiteboard and reduce the contrast of the projected image.
IMPORTANT
Locate a wall with a flat, regular surface and minimum clearance to accommodate your interactive whiteboard
system. Make sure that the UF55 projector and the SMART Board interactive whiteboard are installed on the
same flat surface. For best presentation alignment, SMART recommends that you mount your interactive
whiteboard system in a location that is central to your audience’s viewing direction. For mobile installation or
adjustable installation options, contact your
authorized SMART reseller. If the mounting surface is slightly
irregular or if you’re unable to mount the interactive whiteboar
d system directly on a stud, consult the Reinforcing
a SMART Board 600i3 Series Interactive Whiteboard System Wall Mount Installation with a Backer Board
(
document 135075) on the SMART Support website.
Recommended Heights for Mounting
SMART includes a mounting template with each of its UF55 projector parts kits. If you lose this template, contact
your authorized SMART reseller
. Using this template ensures that you:
Mount the UF55 projector at a safe height for head-space clearance, while maintaining enough space for
airflow and installation access above the projector.
Position the projector at the correct height above the interactive whiteboard to make sure that the projected
image aligns with the touch screen.
Dimensions on the template recommend a distance from the floor that is suitable for adults of average height.
Consider the general height of your user community when you choose a position for the interactive whiteboard,
and consult your local regulations before mounting your interactive whiteboard.
Using the UF55 projector near a TV or radio might cause interference to the images or sound. If
this happens, move the TV or radio away from the projector.
WARNING
When mounting the projector on a framed wall, you must attach both the mounting bracket
and safety tether to a stud to safely support the projector’s weight. If you use only drywall
anchors, the drywall can fail, resulting in product damage and possible personal injury.
If you remove the bolt supporting the limit strap, the projector boom will be free to swing.
Make sure that the bolt is tightened, and never remove it from the unit without supporting the
projector boom first.
Failure to follow the installation instructions shipped with your SMART product could result in
personal injury and damage to the product.
Two people are required to mount the projector and the interactive whiteboard on a wall
because they might be too heavy for one person to maneuver onto their wall-mounting
brackets.
8 Installing Your UF55 Projector Parts Kit 99-00964-20 A0
Adjusting the Image Alignment
After you install the UF55 projector with your SMART Board 500 series interactive whiteboard, you must adjust
the image alignment.
Diagnosing Alignment Errors
Keystone errors occur when the projected image isn’t perpendicular to the screen.
From the projector, the image path is
shorter along the top.
From the projector, the image path is
shorter along the bottom.
The image appears shorter across the top when the distance from the projector to the top of the screen is shorter
than the distance to the bottom of the screen. The image appears shorter across the bottom when the distance
from the projector to the bottom of the screen is shorter than the distance to the top of the screen. Vertical
keystone errors can occur when you mount the UF55 projector and the SMART Board interactive whiteboard on
an uneven surface or a wall that has obstructions.
Horizontal keystone errors can occu
r when you swivel the UF55 projector too far from the SMART Board
interactive whiteboard’s vertical center, when you mount the projector and the interactive whiteboard on an
uneven surface or when the interactive whiteboard is slightly closer to the projector on one side than the other.
From the projector, the image path is
shorter along the right side.
From the projector, the image path is
shorter along the left side.
The image appears shorter across the right side when the distance from the projector to the right of the screen
is shorter than the distance to the left of the screen. The
image appears shorter across the left side of the image
when the distance from the projector to the left of the screen is shorter than the distance to the right of
the screen.
99-00964-20 A0 Installing Your UF55 Projector Parts Kit 9
Adjust the interactive whiteboard side to side to center the image (from the projector), as illustrated in the
installation document, the Parts Kit for SMART Board 560 and 580 Interactive Whiteboards and UF55 Projectors
(document 134836). This eliminates many keystone errors. If your installation environment prevents you from
moving the interactive whiteboard, you can adjust the
projector boom for optimal image alignment.
NOTES
If you move the interactive whiteboard system to a new location, you must re-adjust it.
If your projector requires service, you must adjust the replacement projector.
Performing an Image Alignment
Use this procedure to obtain a rectangular image that is slightly smaller t
han the interactive whiteboard’s screen.
NOTES
Project a computer image (set to the proper resolution) while performing the following steps. If you don’t
have a computer, use the projector’s default blue background so that you can see the full projected
image clearly.
SMART doesn’t recommend adjusting the digital keystoning within the projector. Instead, use the
mechanical adjustment described below.
Ensure that you remove the plastic lens cover from the projector.
1. Align the top of the projected image so that it’s parallel with the top edge of the interactive
whiteboard’s surface.
a. Loosen the large wingnut on the top of the ball joint to allow the projector to move as needed.
NOTE: Don’t loosen the wingnut too much or the projector will not hold the adjustments.
WARNING
Two people are required to mount the projector and the interactive whiteboard on a wall
because the items might be too heavy for one person to maneuver onto the
wall-mounting brackets.
To perform an image alignment
10 Installing Your UF55 Projector Parts Kit 99-00964-20 A0
b. Tilt the projector left or right, up or down, or move it from side to side, until the top edge of the projector
image is parallel with the top edge of the interactive whiteboard.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

SMART Technologies 99-00964-20 User manual

Category
Data projectors
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI