User’s Manual
LCD Color TV
AHH17LCDVD
Features:
No radiation, free from flick, protecting your eyesight and keeping you healthy
High brightness, high contrast, wide viewable angle
No scan line, high quality picture
CATV full channel receiving, 200 channels storage
VGA interface, support XGA
Low power consumption, energy saving and environment protection
Read this manual carefully and keep it handy for future reference.
CONTENTS
Safety instructions.................................................................................................. 1
To place................................................................................................................. 1
Power cord protection............................................................................................ 1
! Precaution........................................................................................................ 1
Maintenance.......................................................................................................... 2
Other items............................................................................................................ 2
Installation ............................................................................................................... 2
To connect the antenna......................................................................................... 2
To connect the power ............................................................................................ 2
Remote control’s battery installation...................................................................... 3
Brief introduction of operation system................................................................. 3
Brief introduction of control panel.......................................................................... 3
Brief introduction of the terminals on back cover................................................... 4
Remote control (TV mode and so on).................................................................... 5
Basic operation ....................................................................................................... 6
To turn on/off the TV.............................................................................................. 6
To receive TV program .......................................................................................... 6
To adjust volume.................................................................................................... 6
Mute ...................................................................................................................... 6
Receiving channel by pressing number key .......................................................... 6
The usage of menu on TV mode ........................................................................... 7
To use VIDEO MENU......................................................................................... 7
To use AUDIO MENU......................................................................................... 7
To use TV MENU............................................................................................... 7
SYSTEM......................................................................................................... 7
AUTO SEARCH.............................................................................................. 8
MANUAL SEARCH......................................................................................... 8
FINE TUNE and AFC...................................................................................... 8
FINE TUNE................................................................................................. 8
AFC............................................................................................................. 9
SKIP............................................................................................................... 9
SWAP............................................................................................................. 9
To use GENERAL MENU................................................................................. 10
LANGUAGE ................................................................................................. 10
BLUE SCREEN............................................................................................ 10
NOISE REDUCE.......................................................................................... 10
RESET ......................................................................................................... 10
The usage of menu on PC mode..........................................................................11
To use PC MENU..............................................................................................11
The usage of menu on AV mode, SCART mode, S-VIDEO mode and DVD mode11
PC supporting mode............................................................................................. 12
Remote Control (on DVD mode) .......................................................................... 13
Basic Operations and Functions(DVD) ............................................................... 15
Place a disc......................................................................................................... 15
Select Playing...................................................................................................... 15
MENU.................................................................................................................. 15
TITLE................................................................................................................... 15
DISPLAY function................................................................................................ 15
LANGUAGE selection ......................................................................................... 16
SLOW/STEP........................................................................................................ 16
TIME selection..................................................................................................... 17
SUBTITLE LANGUAGES.................................................................................... 17
ZOOM.................................................................................................................. 17
ANGLE ................................................................................................................ 17
REPEAT playing.................................................................................................. 18
PROGRAM playing.............................................................................................. 18
To Use DVD Function Setup Menu....................................................................... 19
Basic Operation Procedure.................................................................................. 19
To Use SYSTEM SETUP Menu........................................................................... 19
TV SYSTEM..................................................................................................... 19
VIDEO.............................................................................................................. 20
TV TYPE.......................................................................................................... 20
PASSWORD .................................................................................................... 20
RATING............................................................................................................ 21
DEFAULT......................................................................................................... 21
To Use LANGUAGE SETUP Menu...................................................................... 21
OSD LANGUAGE ............................................................................................ 21
AUDIO LANG................................................................................................... 22
SUBTITLE LANG............................................................................................. 22
MENU LANG.................................................................................................... 22
To Use AUDIO SETUP Menu .............................................................................. 23
AUDIO OUT..................................................................................................... 23
TONE............................................................................................................... 23
To Use DIGITAL SETUP Menu............................................................................ 24
DYNAMIC RANGE........................................................................................... 24
DUAL MONO ................................................................................................... 24
Connection of external equipment...................................................................... 25
Trouble-shooting................................................................................................... 26
Specification and Accessory................................................................................ 28
Specifications....................................................................................................... 28
Accessories......................................................................................................... 28
1
Safety instructions
To place
Place the TV set on a horizontal, stable surface, do not block the ventilation
holes, avoid placing the TV in direct sunshine or near heating source, otherwise
the internal components will be damaged.
Power cord protection
Connect the AC power correctly, and ensure to ground perfectly, be careful not
to damage the power cord. Do not place it under a heavy object. Do not let it be
spliced, worn out or knotted. Do not pull or bend the power cord.
! Precaution
If and when anything abnormal, turn off the power immediately, unplug the
power plug from the outlet and call the shop for repair. Do not remove the
back cover by yourselves in order to avoid electrical shock. Laypeople are not
allowed to repair the TV set by himself.
Do not use the power adaptor that not matches the TV set.
When away for a long time, unplug the power plug.
Do not plug or pull the power plug using wet hand.
When you plug or pull the power plug, hold the isolation part of the plug, do
not pull the power cord.
Do not drip or splash water on the TV set. Do not put the container that
contains liquid on the TV set, in order to avoid electrical shock or damage.
Do not put any objects or container that contains liquid on the TV set. The
liquid may leak into the TV set through the ventilation hole and cause
electrical leakage.
Do not cover the TV set in order to avoid the temperature rising too high and
cause damage.
Do not press or touch the panel.
Do not touch the antenna cable in lightening weather.
Do not touch the terminal on the back cover when the TV set is at work.
Do not connect any insecurity accessories to the TV set.
Set up the antenna away from highways, power lines and neon signs.
2
On back cover
ANT
Maintenance
In case of maintenance, please confirm that the power is turned off and the plug is
pulled out.
Do not use benzene, petrol or oil thinner to clean the TV.
Clean the cabinet with a soft and dry cloth. If the cabinet is very dirty, use a soft and
wet cloth, then dry it.
Clean the LCD panel with soft, dry paper or cloth, do not press the panel.
To avoid scratches please wipe the panel & TV box gently.
Other items
Please confirm that the power is turned off when the TV set is loaded and transported;
do not touch, especially do not press the panel during loading and transportation.
Do not turn on and off the TV set continuously, stop at least 2 seconds, otherwise it
will decrease the TV set’s life cycle.
Be careful with condensation at sudden temperature change. Condensation makes
damage to panel, wait for sometime (still be electrified), until it dissolves.
Avoid to display the still picture for a long time, it will damage the panel. We will not
repair the TV set free from charge caused by this reason.
Check the antenna periodically and change it in time when it is damaged.
Installation
Turn the TV set off when it is connecting the signal or power cord.
To connect the antenna
Connect the antenna or the CATV signal cable directly to the
antenna input terminal located at the back cover, otherwise it will cause
poor image.
Notes: 1. Please use 75Ω coaxial cable, in order to eliminate the
interference caused by the radio wave.
2. Do not band the antenna cable and the power cord
together.
To connect the power
Insert one end of the power cable of the adapter to the power input
terminal located at the back cover and other end of the power cable of
the adapter to the power outlet (AC 100V~240V 50/60Hz), which is
grounding perfectly.
The power adopted by this TV set: DC 12V 5A
When away for a long time, unplug the power adaptor’s plug from
AC power outlet.
On back cover
POWER
3
Remote control’s battery installation
Remove the battery cover; insert two size AAA batteries matching the +/- polarities of
the battery to the +/-marks inside the battery compartment.
The battery life should be about one year under normal use.
When the remote control will not be used for a long period of time,
remove the batteries to prevent leakage.
Do not use rechargeable Ni-Cd battery.
If it is out of battery, change the two batteries at same time.
Do not use different model (different material) battery.
Do not recharge the battery.
Brief introduction of operation system
Brief introduction of control panel
Same function keys on control panel and on remote control
Key on control panel Key on remote control
POWER
SOURCE INPUT
MENU LCD-MENU
CH - / CH + CH - / CH +
VOL - / VOL + VOL - / VOL +
Part of the Remote
Control’s back
Standby
Control panel
4
Brief introduction of the terminals on back cover
1. Power input terminal, DC12V.
2. VGA input terminal, connecting computer’s analog RGB signal.
3. S- video input terminal, connecting external AV equipment’s S-video signal.
4. Video input terminal, connecting external AV equipment’s video signal.
5. Audio input terminal, connecting external AV equipment’s audio signal.
6. VGA audio input terminal, connecting computer’s sound card.
7. 75Ω antenna input terminal, connecting CATV signal.
8. SCART input terminal.
Terminal board on back cover
6
51 2 743
8
5
Remote control (TV mode and so on)
1. POWER—Power key
2. 0-9—Numeric key
3. -/-- —Switch between one-digit number and
multi-digital number.
4. VOL - / VOL+—Decrease / increase volume
5. CH - /CH +—Decrease / increase the
program number
6. AUTO—To adjust the phase, clock,
H.POSITION and V.POSITION automatically
(only on PC mode).
7. —Return to the last program
8. DISPLAY—To display the current program
number and receiving system
9. /—To select menu item
10. /—To adjust menu item
11. LCD-MENU—TV Menu key
12. PMODE—To select picture mode:
PERSONAL, STANDARD, MILD and
FRESH. PERSONAL mode stores the
picture the user sets.
13. INPUT—To select current input signal’s kind:
TV, SCART, PC-RGB, AV, S-VIDEO or DVD.
14. SMODE—To select sound mode:
PERSONAL, VOICE, MUSIC and THEATRE
mode stores the sound the user sets.
15. MUTE—Mute key
1
2
3
10
4
12
5
15
8
6
7
9
11
14
13
AHH17LCDVD
6
Basic operation
The key mentioned in this chapter refers to the key on the remote control, for some
functions you can also press the button on control panel, for details, please see “Brief
introduction of operation system—Brief introduction of control panel”.
To turn on/off the TV
1. Press the button on control panel (confirm the power cord is connected correctly),
turn on the TV.
2. If the TV is at standby status, press<POWER> on the remote control, the TV is turned on.
3. Press <POWER> on the remote control again, the TV will enter into standby status.
4. If you want to turn off the power completely, unplug the power adaptor’s plug from AC
power outlet.
To receive TV program
1. At TV mode, Press <LCD-MENU> three times, “TV MENU” will display on the screen.
2. Press <>/<> to select “AUTO SEARCH” item.
3. Press <>, The TV will auto search.
4. If you want to stop auto search, press <> to exit. Please
note that this operation will eliminate all the channels you
search originally, only store the channel you searched just
before you stop the auto search.
After auto search finishes, you can change the channel by
pressing <CH+>/<CH->, or press the number key to enter into your desired channel
directly.
To adjust volume
Press <VOL+>/<VOL->, you can increase or decrease the volume directly.
Mute
Press <MUTE>, the mute mark will display on the screen, it indicates the mute
function is turned on, the sound disappears, press <MUTE> again, the mute mark will
disappear on the screen, it indicates the mute function is turned off, the sound recovers.
Receiving channel by pressing number key
When you select the channel number 0~9, press the relevant number key;
When you select the channel numbers 10~99, press the “-/--” until the screen displays
“ --” then press the channel numbers.
When you select the channel numbers 100~199, press the “-/--” until the screen
displays “ ---” then press the channel numbers.
TV MENU
CHANNEL 8
SYSTEM DK
SKIP OFF
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
7
The usage of menu on TV mode
On TV mode, press <LCD-MENU> continually， the screen displays “VIDEO
MENU”， ”AUDIO MENU”, “TV MENU” and “GENERAL MENU” respectively.
To use VIDEO MENU
Press <LCD-MENU>, the screen displays “VIDEO
MENU”. There are BRIGHTNESS, CONTRAST, COLOR,
and SHARPNESS in “VIDEO MENU”, for example
“BRIGHTNESS”, the adjusting procedure is as follows:
1. Press <>/<> to select “BRIGHTNESS” item.
2. Press <>/<> to adjust “BRIGHTNESS” to the best.
To adjust other items, you can refer to above operation.
To use AUDIO MENU
Press <LCD-MENU> twice, the screen displays “AUDIO
MENU”. There are VOLUME, BALANCE, AUDIO PRESET,
TREBLE and BASS in “AUDIO MENU”, for example
“VOLUME”, the adjusting procedure is as follows:
1. Press <>/<> to select “VOLUME” item.
2. Press
<>/<> to adjust “VOLUME” to the best.
To adjust other items, you can refer to above operation.
AUDIO PRESET: PERSONAL, VOICE, MUSIC and
THEATRE.
To adjust TREBLE and BASS items, you must set the AUDIO PRESET item at
PERSONAL mode.
To use TV MENU
Press <LCD-MENU> three times, the screen displays “TV MENU”. There are
CHANNEL, SYSTEM, SKIP, AFC, FINE TUNE, SWAP， MANUAL SEARCH and AUTO
SEARCH in “TV MENU”, the adjusting procedure is as follows:
SYSTEM
1. Open “TV MENU”, press <>/<> to select “SYSTEM”
item.
2. Press <>/<> to select correct system.
SYSTEM: BG, DK, I
TV MENU
CHANNEL 8
SYSTEM DK
SKIP OFF
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
VIDEO MENU
BRIGHTNESS 50
CONTRAST 50
COLOR 50
SHARPNESS 50
AUDIO MENU
VOLUME 50
BALANCE 50
AUDIO PRESET PERSONAL
TREBLE 50
BASS 50
8
AUTO SEARCH
1. Open “TV MENU”, press <>/<> to select “AUTO
SEARCH ” item.
2. Press <>, The TV will auto search.
3. If you want to stop auto search, press <> to exit. Please
note that this operation will eliminate all the channels you
search originally, only store the channel you searched just
before you stop the auto search.
After auto search finishes, you can change the channel by pressing <CH+>/<CH->, or
press the number key directly to select your desired channel.
MANUAL SEARCH
1. Open “TV MENU”, press <>/<> to select “MANUAL
SEARCH” item.
2. Press <>, the screen displays MANUAL SEARCH
sub-menu, press <>/<> to select, the item becomes
green after you select it, when you select ”DOWN”, press
<LCD-MENU> to search to low frequency; when you
select ”UP”, press <LCD-MENU> to search to high
frequency. It stops after you search a channel and store the channel
into the current channel number.
FINE TUNE and AFC
FINE TUNE
Some channels’ signal is not ideal after auto search, use
FINE TUNE item.
1. Open “TV MENU”, press <>/<> to select “FINE TUNE”
item.
2. Press <>/<> to adjust and improve the image quality,
after fine tuning finishes, the system will store the result
automatically.
TV MENU
CHANNEL 8
SYSTEM DK
SKIP OFF
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
TV MENU
CHANNEL 8
SYSTEM DK
SKIP OFF
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
DOWN UP
49.75MHz
TV MENU
CHANNEL 8
SYSTEM DK
SKIP OFF
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
9
AFC
1. Open “TV MENU”, press <>/<> to select “AFC” item.
2. Press <>/<> to select “ON” or “OFF”.
ON—It indicates the AFC function is on, the system
conducts the AFC automatically.
OFF—It indicates the AFC function is off.
SKIP
If you unsatisfied with some channels or if some
channels are repeated, you can skip the channel by turn the
SKIP on.
1. Open “TV MENU”, press <>/<> to select “SKIP” item.
2. Press <>/<> to select “ON”
3. If you want to recover these channels, adjust “CHANNEL”
item in “TV MENU” to the channel number you want to
recover, then set “SKIP” to “OFF”.
Press <CH+>/<CH->, the skipped channel will not appear, but if you press number key,
you can still see the skipped channel.
SWAP
Using this function you can change two channel’s
position. for example: to change the channels between “8”
and “35”.
1. Open “TV MENU”, press <>/<> to select “SWAP” item.
2. Press <>, the screen displays SWAP sub-menu, press
<>/<> to select “FROM” item, press <>/<> to
select “8”.
3. Press <>/<> to select “TO” item, press <>/<> to select “35”.
4. Press <>/<> to select “SWAP” item, press <> to finish
“SWAP”.
TV MENU
CHANNEL 8
SYSTEM DK
SKIP OFF
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
TV MENU
CHANNEL 8
SYSTEM DK
SKIP ON
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
TV MENU
CHANNEL 8
SYSTEM DK
SKIP ON
AFC ON
FINE TUNE 448MHz
SWAP
MANUAL SEARCH
AUTO SEARCH
FROM: 8
TO: 35
SWAP
10
To use GENERAL MENU
You can adjust LANGUAGE, BLUE SCREEN, NOISE
REDUCE, INPUT SOURCE and RESET in this menu. You
can conduct the following adjustment when the “GENERAL
MENU” is open.
Press <LCD-MENU> four times, the screen displays
“GENERAL MENU”. “INPUT SOURCE” displays the current
mode。
LANGUAGE
1. Open “GENERAL MENU”, press <>/<> to select
“LANGUAGE” item.
2. Press <>/<> to select the menu language.
BLUE SCREEN
1. Open “GENERAL MENU”, press <>/<> to select
“BLUE SCREEN” item.
2. Press <>/<> to select “ON” or “OFF”.
ON—Display the blue screen when there is no signal.
NOISE REDUCE
1. Open “GENERAL MENU”, press <>/<> to select
“NOISE REDUCE” item.
2. Press <>/<> to select “ON” or “OFF”.
ON—
Reduce the noise of the picture, provide clearer
picture.
RESET
1. Open “GENERAL MENU”, press <>/<> to select
“RESET” item.
2. Press <>, the TV recovers the various kind of default
sets when it is out of factory.
GENERAL MENU
LANGUAGE ENGLISH
BLUE SCREEN ON
NOISE REDUCE ON
INPUT SOURCE TV
RESET
GENERAL MENU
LANGUAGE ENGLISH
BLUE SCREEN ON
NOISE REDUCE ON
INPUT SOURCE TV
RESET
GENERAL MENU
LANGUAGE ENGLISH
BLUE SCREEN ON
NOISE REDUCE ON
INPUT SOURCE TV
RESET
GENERAL MENU
LANGUAGE ENGLISH
BLUE SCREEN ON
NOISE REDUCE ON
INPUT SOURCE TV
RESET
GENERAL MENU
LANGUAGE ENGLISH
BLUE SCREEN ON
NOISE REDUCE ON
INPUT SOURCE TV
RESET
11
The usage of menu on PC mode
On PC mode, press <LCD-MENU> continually， the screen displays “PC MENU”，
“AUDIO MENU” and “GENERAL MENU” respectively. “AUDIO MENU” and “GENERAL
MENU” ’s operation methods are the same as that of the TV mode.
To use PC MENU
There are BRIGHTNESS, CONTRAST, COLOR SETTING, AUTO CONFIG,
H-POSITION V-POSITION, PHASE and CLOCK in PC MENU.
For example: the “BRIGHTNESS”, the adjusting procedure is as follows:
1. Press <LCD-MENU> to enter into “PC MENU”.
2. Press <>/<> to enter into “BRIGHTNESS” item.
3. Press <>/<> to adjust the “BRIGHTNESS” to the best.
Except “COLOR SETTING” and “AUTO CONFIG”, other
items’ adjustment can refer to the above operation.
COLOR SETTING: select among 9300K, 6500K and
user define.
When you select “user” mode in “COLOR SETTING” item,
the screen displays “USER COLOR SETTING” sub-menu, the
adjusting procedure is as “BRIGHTNESS” item.
After you select “AUTO CONFIG” item, press <>, the
system will adjust PHASE, CLOCK and POSITION automatically. You can press <AUTO>
key on the remote control directly to conduct AUTO function.
The usage of menu on AV mode, SCART mode, S-VIDEO mode and
DVD mode
Press <INPUT> to select AV, SCART, S-VIDEO or DVD.
On AV, SCART, S-VIDEO or DVD mode, press <LCD-MENU> continually， the screen
displays “VIDEO MENU”(“DVD MENU”)， “AUDIO MENU” and “GENERAL MENU”
respectively.
Operation method is the same as that of the TV mode.
PC MENU
BRIGHTNESS 50
CONTRAST 50
COLOR SETTING 9300K
AUTO CONFIG
H-POSITION 50
V-POSITION 50
PHASE 50
CLOCK 50
USER COLOR SETTING
RED 171
GREEN 171
BLUE 171
12
PC supporting mode
Resolution H-Frequency（kHz） V-Frequency (Hz) Clock(MHz)
720×400
31.47 70 28.322
640×480
20-55 60-85 32.5-60
800×600
20-55 60-85 32.5-60
1024×768
20-70 60-75 25-80
13
Remote Control (on DVD mode)
1. POWER—Power On/Off
2. NUMERIC KEYS—Enter numbers for menu
selection
3. TITLE—When playing the disc, press this key to
return to the title
4. VOL-/VOL+—Decrease / increase volume
5. DISPLAY—Change the mode of the function
display
6. ENTER—Confirm selections on a menu screen
7. PMODE— To select picture mode: MAMUAL,
STANDARD, MILD and FRESH. MAMUAL
mode stores the picture the user sets
8. INPUT—Input signal selection key
9. STOP—Stop playback
10. PLAY/ PAUSE—Press PLAY directly to begin
playback under stop or pause status. Press
pause to pause playback.
11. FORWARD — Multi-grade fast-forward key.
Press this key you can select FORWARDx2,
FORWARDx4, FORWARDx8, FORWARDx20
and PLAY circularly.
12. BACKWARD—Multi-grade fast-backward key.
Press this key you can select BACKWARDx2, BACKWARDx4, BACKWARDx8,
BACKWARDx20 and PLAY circularly.
13. NEXT—Press NEXT to play next chapter
14. PREVIEW—Press PREVIEW to play preview chapter
15. PROGRAM—Program a disc playing in a desired sequence
1
8
9
10
11
12
13
14
15
2
4
3
5
6
7
AHH17LCDVD
14
16. EJECT—To open and close the disc tray
17. MENU—When playing the disc, press the key to
return to the root MENU.
18. ///—Up/down/left/right cursor
19. DVD-SETUP—Used for selecting programs. It
may also be used to execute commands
20. SMODE—To select sound mode: PERSONAL,
VOICE, MUSIC and THEATRE mode stores the
sound the user sets.
21. MUTE—Press MUTE to silence the voice
temporarily
22. SLOW/STEP—Slow forward playback / Enter
step mode where video can be advanced frame
by frame
23. LANGUAGE—Switch among different
languages
24. TIME — Start playing from the desired time.
Press TIME and enter time. The unit starts
playing from the time you selected.
25. SUBTITLE— Select different subtitle language
(the DVD disc must have the subtitle you
selected)
26. ZOOM—Adjust picture size
27. .ANGLE—select different angles to watch the
picture more comfortably
28. REPEAT—Press REPEAT repeatedly repeat all
29. AB—Press AB once to set point A, press AB
again to set point B, the player will play from
point A to point B repeatedly.
Note: To cancel the AB repeat function, press AB
again.
20
16
19
18
21
22
23
24
25
26
27
28
29
AHH17LCDVD
17
15
Basic Operations and Functions(DVD)
Press <POWER> on the TV or the remote control, then press
<TV/AV> to select DVD mode.
Place a disc
Insert a disc with the date side facing towards you.
Do not touch the playing surface.
Hold the disc around the outside with your fingers and place the disc into the slot.
The player will automatically draw the disc into the player.
To eject the disc, press <EJECT> on the remote control
Select Playing
Compatible with DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio disc/JPEG discs.
You can also select your desired track by using the numeric key (but only under PBC
off mode). Press numeric key (0-9, -/--) for selecting.
e.g. : Track No.22 press numeric key -/-- for two times, and then press numeric key 2.
You can also press <TITLE> on the remote control for this function.
MENU
Compatible with DVD, SVCD or VCD2.0.
When playing DVD, SVCD, VCD2.0 discs, press this key to the root menu, you can
choose menu item again.
TITLE
Compatible with DVD discs only.
When playing a disc, press this key to return to the main title and you can choose title again.
DISPLAY function
Compatible with DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio discs.
1. Loading and playing DVD
- Press <DISPLAY> once to show the first page;
DVD TT 1/8 CH 1/28 00∶00∶08
Disc type
Title
The playing chapter
/ The total chapter
Elapsed time of the disc Chapter
The playing title
/ The total title
16
- Press <DISPLAY> again to show the second page;
- Press <DISPLAY> for the third time, the display menu fades out.
2. Loading and playing VCD
- Press <DISPLAY> once to show the first page;
- Press <DISPLAY> again, the display menu fades out.
3．CD, SVCD, HDCD, WMA, Digital Audio disc and JPEG disc‘s display method is
similar as the above.
LANGUAGE selection
Compatible with DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio disc/JPEG discs.
You can choose among eight voice languages by pressing the <LANGUAGE> on the
remote control (the DVD discs must have the audio language you select).
SLOW/STEP
Compatible with DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio disc/JPEG discs.
Press
<SLOW/STEP> on the remote control and movie will play in slow
motion at speed of 1/2,1/3,1/4 and play in cycle by keeping press this key .you
can also press
<PLAY> to return to normal speed.
VCD TRK 1/8 PBC 00∶00∶08
Disc type
Track
Repeat mode
Elapsed time of the disc
Mute
The playing track
/ The total tracks
PBC
Language
Language type
The
playing
subtitle
A
udio type
The serial number
of playing language
/ the amount of
optional language
or Off.
1/2CHI 2CH 1/6 ENG OFF
The serial
number of
playing
subtitle / the
amount of
optional
subtitle or Off.
Subtitle
A
ngle
The serial
number of
playing angle /
the amount of
optional angle
or Off.
17
TIME selection
Compatible with DVD, SVCD, VCD, CD, HDCD discs
1. While playing DVD disc, press TIME, the screen will show the titles and chapters
of the disc.
2. Use the cursor key to select the position, then input position number and press
ENTER to confirm. The disc will play from your selection.
3. While playing VCD disc, press TIME, the screen will show the track, PBC and time
of disc. Follow steps from No.2.
Eg: Enter 01:23:56 will start playback one hour, twenty-three minutes and fifty-six
seconds into the title.
SUBTITLE LANGUAGES
Compatible with DVD, SVCD discs.
This function enables you to select up to 32 subtitle languages to be displayed on TV
screen (only applicable to DVD discs with this function). Repeatedly press the SUBTITLE
key to select your desired language.
ZOOM
Compatible with DVD, SVCD, VCD, JPEG discs.
This function enables you to enlarge the video image.
The maximum zoom is X4.Press the ZOOM key to select X2, X3, X4, 1/2, 1/3, 1/4. In
zoom mode; you can press cursor keys to move the picture.
ANGLE
While watching a game, a concert or opera program, you can:
1.Press the ANGLE key on the remote control to select angle one, the diagram angle
one and the logo will appear in the upper right corner of the TV screen.
DVD TT 01/08 CH 001/028 00∶00∶08
VCD TRK 01/08 PBC 00∶00∶08
18
2.Press the ANGLE key again to select a different angle, or you can choose
to watch the same action taken from different viewing angles.
Note: Subject to movies shot with this function.
REPEAT playing
Compatible with DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio disc /JPEG discs.
When playing SVCD, VCD, CD, HDCD, WMA and Digital Audio / JEPG discs,
you can repeat three repeat options: Off, Track Repeat and Disc Repeat by
pressing the REPEAT key repeatedly.
When playing DVD, you can also repeat three repeat options: Off, Chapter
Repeat and Title Repeat by pressing the REPEAT key repeatedly.
PROGRAM playing
Compatible with DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio disc /JPEG discs.
This function enables you to enter the order in which you want chapters or tracks to
play, maximum to 16.
1.According to the highlight, use the numeric keys to enter the chapters/tracks in the
order you want them to play. Then press PLAY or use cursor keys to highlight the "PLAY"
item and press ENTER. The chapters / tracks will play in the programmed order. You can
program maximum 16 titles / chapters / tracks.
2.According to the Direction Indicator on the menu, you can press cursor keys to
highlight where you want to enter.
3.Duning program playback, if PROGRAM key is repressed, the program order and
the contents will be displayed on the screen, and the program playback will be stopped;
also you can press stop and play to resume normal playback.
4.The program indicator in the screen, and the playing chapter / track illuminate.
Note: To clear the program order, use cursor keys to highlight the "CLEAR" item,
then press ENTER.
To modify the program order, use cursor keys to highlight the item you are
changing and enter the new chapter / track you want to program directly.
19
To Use DVD Function Setup Menu
There are 4 function setup menus in DVD, they are SYSTEM SETUP, LANGUAGE
SETUP, AUDIO SETUP and DIGITAL SETUP.
Basic Operation Procedure
For example: Set English OSD
language in LANGUAGE SETUP menu.
1． Press <DVD-SETUP>, the screen
displays main setup menu, the picture
turns to PAUSE status automatically.
2． Press <>/<> stop the cursor on
LANGUAGE SETUP menu (the menu
will change with the moving of the cursor).
3． Press <>/<> move the cursor to OSD LANGUAGE item, press <ENTER> to
confirm or press <> to enter this item’s sub-menu.
4． Press <>/<> to move the cursor to ENGLISH item, press < ENTER > to confirm
and return to last menu.
5． Press <>/<>, move the cursor to EXIT SETUP item and press < ENTER >, or
press < DVD-SETUP > to exit the setup menu.
If you want to setup other menu, press <>/<> until the cursor disappears, then
press <>/<> to select other menu.
To Use SYSTEM SETUP Menu
There are 6 menu items in SYSTEM
SETUP menu.
TV SYSTEM
The operation refers to the “Basic
Operation Procedure” of the setup menu.
TV SYSTEM: Select according to TV’s
color system.
20
VIDEO
Defined as INTERLACE-YUV.
TV TYPE
The operation refers to the “Basic
Operation Procedure” of the setup menu.
a) 4:3PS: When DVD broadcasts wide
screen picture, cut the right and left
edge of the picture, let the picture
occupy the whole screen.
b) 4:3LB:When DVD broadcasts wide screen picture, black frame appears on the top
and bottom of the screen.
c) 16:9:Select this item when the DVD is connected to wide screen TV.
PASSWORD
This item’s original setup is
“PASSWORD”, at this time you can’t select
“RATING” item, and you can’t modify the
password either. If you want to setup the
“RATING” item, you have to input the
original password by press the numeric key
on the remote control, the original password is :0000, then press <ENTER> to confirm.
If you want to modify the password, input the old password, then input the new
password (the effective password is a four-digit number).
21
RATING
When you play the disc that has locking
function, according to the rating of the disc
and your practical requirement, select proper
rating. The operation refers to the “Basic
Operation Procedure” of the setup menu.
The rating is divided into KID SAFE, G,
PG, PG13, PG-R, R, NC-17 and ADULT.
Note: Only when the password lock is open, you can select the rating, and only
when the password lock is locked, the rating limit is effective.
DEFAULT
The operation refers to the “Basic
Operation Procedure” of the setup menu.
This item is used to restore the factory
settings.
To Use LANGUAGE SETUP Menu
There are 4 items in LANGUAGE
SETUP menu. The operation refers to the
“Basic Operation Procedure” of the setup
menu.
OSD LANGUAGE
There are 6 languages for you to select:
ENGLISH, GERMAN, SPANISH, FRENCH,
PORTUGUESE and ITALIAN.
22
AUDIO LANG
There are 8 languages for you to select:
CHINESE, ENGLISH, JAPAN, FRENCH,
SPANISH, PORTUGUESE, GERMAN and
ITALIAN.
SUBTITLE LANG
There are 8 languages for you to select:
CHINESE, ENGLISH, JAPAN, FRENCH,
SPANISH, PORTUGUESE, GERMAN and
ITALIAN.
MENU LANG
There are 8 languages for you to select:
CHINESE, ENGLISH, JAPAN, FRENCH,
SPANISH, PORTUGUESE, GERMAN and
ITALIAN.
Note: If you want to set AUDIO LANG,
SUBTITLE LANG or MENU LANG in
the menu, you must be sure the
setted language in the menu will display only when you insert the disc again.
Generally the disc will remind you whether to set the above language at the
beginning of the broadcasting.
If the language you select is not recorded in DVD disc, the DVD will select default
language the disc has recorded.
23
To Use AUDIO SETUP Menu
There are 2 items in AUDIO SETUP
menu.
AUDIO OUT
Here, the AUDIO OUT is defined as
ANALOG.
TONE
When the screen displays “AUDIO
SETUP” menu, press <>/<> to select
“TONE” item, press <ENTER> to confirm.
Press <>/<> again to adjust, press
<ENTER> to confirm.
24
To Use DIGITAL SETUP Menu
There are 2 items in DIGITAL SETUP
menu.
DYNAMIC RANGE
When the screen displays DIGITAL
SETUP menu, press <>/<> to select
DYNAMIC RANGE item, press <ENTER> to
confirm, press <>/<> to adjust, press
<ENTER> to confirm.
In this item, when you select “FULL”,
the PP value of audio signal is minimum, when you select OFF, the PP value is maximum.
DUAL MONO
The operation refers to the “Basic
Operation Procedure” of the setup menu.
This item can set the output method of
audio out (L, R) signal, it includes 4 modes:
STEREO, MONO L, MONO R and MIX
MONO,
25
Connection of external equipment
You should turn off the power when you connect all the connecting line (turn off the
power and pull out the adaptor).
This TV set can connect the AV equipment that has video, SCART or S-video, audio
output terminal. It can also connect the computer. Please refer to the user’s manual of the
external equipment when you connect. The user should buy the connecting cord by
yourself except the power cord.
AV equipment connecting procedure:
1. Ensure this TV ’s power and external equipment’s power are all turned off.
2. Connect external equipment’s Video out, SCART out or S-Video out to this TV set’s
Video in, SCART in or S-Video in on the back cover by using signal line.
3. Connect external equipment’s Audio out to this TV set’s Audio in on the back cover by
using audio connecting line.
4. After the connection finishes, turn on this TV’s power, and then turn on the external
equipment’s power.
5. Press <INPUT> to select “AV”, “SCART” or “S-VIDEO”, set the TV on AV, SCART or S-VIDEO mode.
PC connecting procedure:
1. Ensure this TV’s power and the PC’s power are all turned off.
2. Connect PC’s VGA interface to this TV’s VGA input terminal on the back cover by using
D15 VGA line, and then drive the screw.
3. Connect PC’s sound card to this TV’s VGA Audio input terminal on the back cover by
using audio connecting line.
4. After the connection finishes, turn on this TV’s power, and then turn on PC’s power.
5. Press <INPUT> to select “PC”, set the TV on PC mode
VCR、DVD、Video player and so on
VIDEO
OUT
AUDIO
L OUT R
S-V IDEO
OUT
Computer
Terminal board on back cover
26
Trouble-shooting
Check the following table before contact repairing place, many troubles are caused by
simple reason or by mis-adjustment, check it by yourself and the TV set will recover
normal.
SOLUTION
TROUBLE
12345 6 7 8 9 1011121314151617181920
No picture, no sound
• • • • •
Poor sound, good picture
• • • • •
Poor picture, good sound
• • • • • • • • •
Weak and blurred picture
• • • • •
Ghost image
• • • •
Dotted line or stripes
• • • • •
Abnormal pictures
• • • • •
Diagonals on screen
• •
Rolling picture
• •
Poor color
• • • • • • •
No color
• • • • • • • • •
Remote control failure
• •
The picture is not at
screen center
•
“No signal” appears
•
“Over range” appears
•
Appearing interference
line on “Close Windows”
picture
•
Disc cannot be played
•
Notes:
1. Check if the power is turned on.
2. Try another channel, as it may be TV station breakdown.
3. Check antenna or CATV cable connection.
27
4. Check if antenna or CATV cable is broken.
5. Adjust indoor antenna’s direction.
6. Interference of device nearby.
7. Tuning doesn’t work well.
8. Adjust brightness.
9. Adjust contrast.
10. Check if TV station is broadcasting color program.
11. Adjust color controlling
12. Direct the remote control to the infrared sensor.
13. Check battery in the remote control.
14. Check the TV’ system.
15. Check the TV’ system.
16. Use “AUTO” key or adjust “H.POSITION” and “V.POSITION” manually.
17. Check if the VGA cord is connected correctly, if the PC power is turned on.
18. On PC mode, the input signal refers to “PC Supporting mode”.
19. Use “AUTO” key or “PC MENU” to adjust “PHASE” and “CLOCK” (only on PC mode).
20. Disc is loaded incorrectly. / Disc is dirty. / Disc is bent or warped.
The following conditions are not failures:
1. While using, the TV set may has sound but no picture, it may be the memory circuit is
interfered by some external element, please turn off the main power, after one minute,
turn it on again and it may be recovery. If it is still abnormal, contact the local service
center.
2. The clicking is a creaking sound produced when the cabinet expands or contracts due
to changes of temperature. This will not affect the picture or sound.
3. If the remote control is slow witted, it may be caused by the interference of the
electronic energy-saving light and so on, please turn off the relative equipment.
4. Because there are great number of data need to be read into CPU buffer, so operate
the TV set after the picture has been normal for 3 seconds.
28
Specification and Accessory
Specifications
1. System PAL D/K B/G I
2. Video input PAL NTSC
3. Screen TFT-LCD display panel
The active diagonal size of the viewable image is 43cm(17”).
4. View range (H/V) 120/100
5. Power DC 12V
6. Power consumption 55W
7. Sound power (10% distortion allowed) R.L channel 2W+2W
8. Interface AV, S-VIDEO, VGA, SCART
9. Compatible DISC:
DVD, SVCD, VCD, CD, HDCD, WMA, Digital Audio disc /JPEG disc
10. Dimensions (approximately) See the package box
11. Quantity (approximately) See the package box
Note: No notification is required for any change of the technical data.
Accessories
Accessory Quantity Remark
User’s manual 1
Warranty card 1
Remote control/ AAA battery 1/2
Power adaptor 1 set Including power cord
0R20254902
200671
Items for check:
Purchase date
Model
Agent
Series number
LCD Color TV
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Denver TFD 1905 Owner's manual
-
VIORE LCD26VH59 Owner's manual
-
Radio Shack Car Video System PTC20LD User manual
-
Hyundai H-LCD1509 User manual
-
Coby TV-DVD1050 User manual
-
Palsonic TFTV525WS User manual
-
-
VESTEL 1530 Owner's manual
-
Haier L1920A-C User manual
-
Haier L15C10A User manual