Bogen D User manual

Brand: Bogen

Model: D

Category: Car media receivers

Type: User manual

DRZ120

6-Zone Music & Paging System

Specifications subject to change without notice.

54-2233-01B 1606

NOTICE: Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing.

However, information is subject to change.

WARNING: To reduce the risk of Fire or Electric Shock, Do Not Expose this apparatus to rain or moisture. The apparatus shall not

be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

WARNING: Only connect unit to AC mains outlet providing protective earthing connection.

NOTE: Mains plug is used as disconnect device from the mains and shall remain readily accessible and operable.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not per-

form any servicing other than that contained in the operating instructions unless you are qualified to do so.

Always follow these basic safety precautions when installing

and using the unit:

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean unit with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding-type plug has two blades and a third

grounding prong.The wide blade, or the third prong, are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by manufacturer.

12. Unplug this apparatus during lightning storms or when not

used for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

CAUTION: DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET, OR IN ANOTHER CONFINED

SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT THE RISK OF SHOCK OR FIRE HAZARD DUE TO OVER-

HEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.

CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE ANY FRONT/ BACK COVERS OR PANELS. NO USER-

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL.

The exclamation point that is

within an equilateral triangle

is intended to alert the user

to the presence of important

operating and maintenance

(servicing) instructions.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which

can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by

one or more of the following measures:

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Contents

Page

DRZ120 FRONT PANEL ........................................................................................................................2

DRZ120 REAR PANEL ..........................................................................................................................3

INFRARED REMOTE CONTROLLER........................................…………………………………………...4

INSTALLATION ..........................................…………………………………………………………………...5

CONNECTIONS..........................................…………………………………………………………………...6

OPERATION ..........................................…………………………………………………….………………...7

TECHNICAL SPECIFICATIONS..................…………………………………………………………………..8

LIMITED WARRANTY; EXCLUSION OF CERTAIN DAMAGES ..........................................................9

DRZ120 6-Zone Music & Paging System

DRZ120 Front Panel

1. Master POWER Switch

Turns Power to DRZ120 unit ON or OFF.

2. Power ON Indicator

Indicates when Power is on.

3. BASS Tone Control

Controls the amount of cut or boost of Bass

frequencies below 100 Hz.

4. TREBLE Tone Control

Controls the amount of cut or boost of Treble

frequencies above 10 kHz.

5. LINE Input Level Controls

Controls level of each Line input.

6. MIC1 and MIC2 Input Level Controls

Controls level of MIC1 and MIC2 inputs.

7. MIC1 IN Input

Accepts 1/4” TRS-type microphone input connector.

8. Zone Output Level Controls

Individual control levels for the output of each

of six zones (ZONE 1 thru ZONE 6).

9. Zone Level LED Indicators

Indicates zone output level visually by LED intensity.

The brighter the LED, the louder the zone level.

10. Chime

When the CHIME button is pushed, a short melodic

series of four ascending bell-like tones is generated

to all outputs. These tones are generated at a high

output level, so care should be taken when using

CHIME with high zone output settings.

11. SD Card Slot

Slot for SD Card connection for MP3 files.

12. MP3/TUNER Button

Select MP3 or FM Tuner as input source. Current

selection is displayed on Status Display (#17)

13-15. FM Tuner/MP3 Multi-Operation Buttons

FM Tuner Mode: Advances to the next

station preset.

MP3 Mode: Advances to next track.

FM Tuner Mode: Selects the previous

station preset.

MP3 Mode: Selects previous track.

FM Tuner Mode: Scans preset FM bands.

MP3 Mode: Play/Pause selected track

16. USB Port

Port for USB drive connection for MP3 files.

17. FM Tuner/MP3 Player Status Display

Indicates which mode source is active (RAD, USB,

SD and AUX).

18. Output Level Indicator

Five-segment LED output level indicator. Maximum

recommended operating output level is 8.

Note: When all five units of the LED output level indicator

remain lit, it indicates that the sound is distorted and may

result in undesired audio quality. To resolve this issue,

decrease one or more of the Line/MIC Input levels until

at least one LED does not light. If the output level is

allowed to 'max. out' (i.e., output level of 10) for any

extended period, then the unit will enter 'protection mode' -

opening a output protection relay and sounding an alarm.

To reset the alarm, the Power Switch (#1) must be turned

OFF and then back ON.

BASS

-10

POWER

Output Level

246810

FM Tuner / MP3 Player

USB Music Source

TREBLE

-10

LINE 3

LINE 2

LINE 1

MIC 2

MIC 1

Input Level

Output Level

MIC 1 IN

CHIME

OFF OFF OFF

DRZ

120

6-ZONE MUSIC & PAGING SYSTEM

DRZ120 Rear Panel

1. MUTE Control

Controls the sensitivity of the MUTE function.

2. MIC2 Input Connection

XLR style microphone input connector.

3. LINE INPUT Connections

RCA style auxiliary input connections for each

of 3 LINE inputs.

4. AUX Output Connection

RCA-style connector for post-mix, line-level auxiliary

output.

5. 6-Zone Output Terminal Strip

Connect up to 6 groups of 70V speakers to this

terminal strip. Output level controls are located

on the front panel.

6. AC Power Cord Socket

Connection for power cord to 120V AC, 60 Hz outlet.

7. Fan Exhaust

Cooling air outlet.

8. AC Power Fuse

The fuse is a fast-blow (fast-acting fuse), glass,

4 Amp, 250 Volt fuse. (F4AL250V)

9. Speaker Output: 4-16

Low-impedance speaker output (4Ω min. load).

10. FM Antenna Connection

F-type coax connector for 75-ohm FM antenna.

11. MIC4 IN Input Connection

Terminal block microphone input connector.

12. MIC3 IN Input Connection

Terminal block microphone input connector.

13. MIC4 VOL Input Level Control

Controls level of MIC 4 input.

14. MIC3 VOL Input Level Control

Controls level of MIC 3 input.

MIC 3 VOL

MIC 4 VOL

MIC 3 IN MIC 4 IN

BAL./UNBAL.

—

MIC 2 LINE 2 LINE 3LINE1 OUT

INPUT

FM ANTENNA

FM (75Ω)

SPEAKER OUTPUT

ZONE OUTPUTS

4-16Ω

F4AL250V

~120V/ 60Hz/6A

CAUTION!

RISK OF

ELECTRICAL

SHOCK.

DO NOT OPEN.

www.bogen.com

DRZ

120

MIN MAX

MUTE

—

COM

ZONE 1

ZONE 2

ZONE 3 ZONE 4

ZONE 5

ZONE 6

COM

Infrared Remote Controller

(for FM Tuner / MP3 Player control only)

1. POWER

Turns power to the FM Tuner / MP3 Player ON or OFF.

2. Mode

Cycles through the RAD (i.e., FM Tuner), USB, SD

and AUX sources each time the button is pressed.*

3. Mute

Press once to silence audio output, press again to

cancel mute. Display on front of DRZ120 will flash

when mute is active.

4. Play/Pause

MP3 Mode:

Toggle play/pause operation. While pause

is active, “PAU” is shown on display.

TUNER (RAD) Mode:

Press repeatedly to advance through

the preset FM channels.

5. Next

MP3 Mode:

Advances to next track.

TUNER (RAD) Mode:

Increases FM frequency selection.

6. Previous

MP3 Mode:

Plays previous track.

TUNER (RAD) Mode:

Decreases FM frequency selection.

7. EQ

MP3 Mode:

Selects desired equalizer mode (None / Classics /Jazz / Rock / Bass / Pop).

TUNER (RAD) Mode

: Cycles through tuner station presets.

8. VOL -

Decreases Tuner/MP3 volume.

9. VOL +

Increases Tuner/MP3 volume.

10. SCN (U/SD)

TUNER Mode:

Causes the FM tuner to scan the entire 88 to 108 MHz FM band. When a station is detected,

the station is stored in the PRESET memory. This is repeated continuously until the entire FM radio band has

been searched. This process takes about 3 seconds per station stored. These numbered presets can then

be selected by either entering a preset’s assigned number on the remote (#12), or by cycling through

them in ascending or descending order using the Play/Pause and EQ buttons on the remote (respectively).

Alternatively, the numbered presets can be cycled through by using the Previous and Next but

tons on the

front panel.

MP3 Mode:

Switches between the USB and SD card as the MP3 input source.

USB Mode:

Toggles the MP3 play mode between “ALL” or “INTRO”.

SD Mode:

Places the MP3 player mode in "ALL".

AUX Mode:

This mode is not supported by this particular model.

11. RPT

Repeat will replay current track continuously, or all tracks continuously. (This functions only in MP3 mode.)

12. 0 thru 9

MP3 Mode:

Input track number to play desired track.

TUNER Mode:

Selects FM Tuner frequency.

Mode

VOL

–

VOL

RPT U/SD

123

456

789

SCN

*Note: The source selection for "USB" or "SD" is only displayed if a USB drive or SD card is plugged into the DRZ120.

Also, although the source selection will display an "AUX" mode, this mode is not supported by this particular model.

PACKAGE CONTENTS

1. DRZ120 6-Zone Music & Paging Unit

2. Infrared Remote Controller

3. Instruction Manual

RACK MOUNTING

When assembling equipment in a rack, the DRZ120 should either be on the bottom of the rack or above any

equipment that does not produce heat to ensure a source of cool air to the bottom of the unit. Provide at least

1 RU (Rack Unit) of space above and below the DRZ120 so that cool air is available to the unit. Rack mounting

brackets are attached to the unit. Use appropriately sized screws.

SHELF / TABLE MOUNTING

When placing the DRZ120 on a shelf or table, the unit should ideally stand alone with no equipment on top of

or beneath it. If the DRZ120 must be stacked with other equipment, care must be taken to ensure that the

DRZ120, which is passively cooled, be allowed a minimum clearance of 1/2” for the bottom (set by height of

the unit s feet) and a minimum of 1” from the top to other obstructions. Be sure that any equipment situated

below the unit produces little heat. The sides of the DRZ120 have no specific clearance area requirements.

These are minimum acceptable clearances, however the more space provided, both top and bottom, the better.

Rubber feet must be installed on the unit to allow it to be placed on a shelf or tabletop.

Installation

Connections

MIC 3

MIC 2

MIC 1

with Priority Input

To MIC1

Input Jack

on Front

Panel

MUSIC SOURCE

RECORDER OR OTHER AMP

MIC 4

MIC 3

MIC 4

MIC 2

MIC 1

with Priority Input

To MIC1

Input Jack

on Front

Panel

MUSIC SOURCE

RECORDER OR OTHER AMP

Without Multi-Zone Outputs

With Multi-Zone Outputs

Note: Individual zone output levels are set by adjusting the Zone Volume Controls on the Front Panel.

Operation

Set up the system according to the connection diagrams on page 6, connect the power supply, and then turn on the

master power switch on the front panel. If an MP3 storage device is connected at startup, the system will autoplay

MP3s present on the device. Otherwise, the system will initially be set to accept audio from the AUX/MIC inputs.

MP3 Operation

In order to play from an MP3 device, insert the USB stick or SD card and press “MP3/TUNER” button or the “Mode”

button on the infrared remote to select the applicable playback mode. Use the and buttons on the remote

control or on the front panel of the amplifier to select the desired track. Pressing the button on the remote or on

the front panel toggles the pause function.

Repeat

Two repeat modes can be selected when playing MP3 audio. Using the remote control, press the “RPT” button to

toggle between the two options. When “ONE” is appears on the display of the DRZ120, the current track will be con-

tinuously repeated. When “ALL” is displayed, all tracks will play and repeat starting from the first track. If this option is

selected while a track is playing, the repeat feature will begin when the final track has finished playing.

When playing MP3 audio, equalization (EQ) settings can be used. There are 6 total options: none, Classic, Jazz,

Rock, Bass, and Pop. Pressing the “EQ” button on the remote control will cause the system to cycle to the next EQ

preset. EQ settings appear on the display are represented by “Eq0, Eq1, Eq2, Eq3, Eq4, Eq5” on the display.

Note:

If multiple MP3 devices are inserted into the amplifier, audio will automatically play from the device that was in-

serted last.

TUNER Operation

To play an FM radio station, press the “MP3/TUNER” button or the “Mode” button on the remote control to select the

applicable playback mode.

Scan

Before playing, it is beneficial for the user to utilize the FM Scan option to have the system memorize station frequen-

cies. Pressing “SCN” on the remote control will automatically have the system scan through the FM radio band and

save stations that can be easily selected at a later time. The display will show the stations being searched from low

to high frequency signals. Saved stations are saved as numbers starting from “1”. The stations can be recalled by

pressing the appropriate saved station numbers on the remote, pressing and “EQ” on the remote to browse

through the saved stations, or by using the and buttons on the front panel.

Station Select

Stations can also be manually selected by inputting a specific station frequency via the “0-9” buttons on the IR remote,

or by using the and buttons on the remote to decrease/increase the selected frequency by 0.1 MHz.

Mute Function

MIC 1 Input Jack and Chime Button have the highest level of priority. Input signals from them

can override other input signals. The sensitivity of this MUTE function can be adjusted by the

trim knob on the rear panel.

Amplifier

Power Rating (RMS): ......................................................120 Watts into 8-ohms

Distortion: ........................................................................ ≤1% THD (Rated output power@1 kHz)

Signal to Noise Ratio: ....................................................

≤ -74 dB

Audio Frequency Response: ........................................80 Hz - 16 kHz @ 4Ω (+/-3 dB)

Zone Outputs:..................................................................120 Watts @70V max. for any single zone, or

20 Watts @70V max. for each zone

(assuming equal loads)

AUX Speaker Output:...................................................... 4-16Ω

Tone Controls: ................................................................ Bass: +/-10 dB @ 100 Hz

................................................................Treble: +/-10 dB @ 10 kHz

Microphone Input: .......................................................... ≤ 3mV/1kΩ unbalanced

MIC1 Precedence: .......................................................... VOX-activated, with adjustable MUTE Control

LINE Inputs: ....................................................................

≤ 300mV/10kΩ unbalanced; RCA jacks

AUX Line Output: ............................................................ 50Ω/ (1V); RCA jacks

Tuner

Station Tuning: ................................................................ Digital, 0.1 MHz increments, with PLL Synthesizer

Band Coverage: .............................................................. FM: 87.5 to 108 MHz

Antenna: .......................................................................... 75-ohm coaxial

Memory Scan:..................................................................Automatically Preset stations

Channel Indicator: .......................................................... Back-lit LCD

Power/Dimensions

Power Required:..............................................................120V AC nominal @ 60 Hz

Power Consumption: ...................................................... 250 Watts

Dimensions: ....................................................................19-1/8" W x 3-1/2" H x 13-3/4" D

Product Weight: ..............................................................25.2 lbs.

Technical Specifications

Limited Warranty; Exclusion of Certain Damages

The Bogen DRZ120 is warranted to be free from defects in material and workmanship for 2 (two) years from

the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal

installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty

period, will be repaired or replaced by Bogen, at Bogen’s option, provided the product is shipped insured and

prepaid to: Bogen Factory Service Department, 4570 Shelby Air Drive, Suite 11, Memphis TN 38118, USA.

Repaired or replacement product will be returned to you freight prepaid. This warranty does not extend to any

of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper

installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number

or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PUR-

CHASER’S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND,

EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT

ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of products or their

use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the

product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE

DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF

BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do

not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which

vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department – same address

as above or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when

repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges

will be at the owner's expense. All returns require a Return Authorization number. For most efficient warranty or

repair service, please include a description of the failure.

11/2014

www.bogen.com

Bogen D User manual

Brand: Bogen

Model: D

Category: Car media receivers

Type: User manual

Download PDF

report

Bogen D User manual

Bogen D User manual

Related papers

Other documents