2. Javad
  3. TRIUMPH-LS

Javad TRIUMPH-LS User manual

  • Hello! I've reviewed the Quick Start Guide for setting up and using the RTPK feature on the JAVAD GNSS TRIUMPH-LS device. This document covers setup, activation, and results processing of RTPK. It also guides you through the process of reviewing two solutions of the measured point. I'm ready to assist you with any questions you may have about this device and its functionality.
  • How do I check if the RTPK option is available?
    How do I activate RTPK in the Collect screen?
    Where can I see RTPK results?
All contents in this manual are copyrighted by JAVAD GNSS.
All rights reserved.The information contained herein may not be used, accessed, copied,
stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express
written consent from JAVAD GNSS.
RTPK on TRIUMPH-LS
HOW TO SET UP AND START
Quick Start Guide
VERSION 1.0
LAST REVISED AUGUST 16, 2021
2 www.javad.com
Contents
1. Check RTPK Options .................................. 3
2. Setup RTPK ................................................ 3
3. Setup RTPK Environment Category .......... 4
4. Activate RTPK in Collect screen ................ 4
5. Auto-Start RTPK ......................................... 4
6. Manual start RTPK ..................................... 5
7. Checking RTPK results .............................. 5
www.javad.com 3
1. Check RTPK Options
Check that the RTPK option is available on your
TRIUMPH-LS.
Go to Support > Options and tap Check (Figure 1):
Figure 1. Checking options
2. Setup RTPK
On the Home screen, got to Setup > Edit (General group)
> What To Record > Turn on RAW GNSS Data and set up
1 HZ.
Press OK and choose RTPK Usage (Figure 2):
Figure 2. Setting up RTPK
Activate all RTPK functions and set up the parameters
(Figure 3):
Figure 3. RTPK Usage
RTPK on TRIUMPH-LS
4 www.javad.com
3. Setup RTPK Environment Category
Go to RTPK Environment Category and choose the
Data Split Interval Auto-Start period aer RTK surveying
(Figure 4).
Figure 4. RTPK settings
4. Activate RTPK in Collect screen
For activating RTPK option in Collect screen tap long
click on the white box (about 2 sec) to switch in the
Groups screen. Click “Setups: margins, signals (etc.)”
(Figure 5):
Figure 5. Setups: margins, signals, ...
Then choose the RTPK option (Figure 6):
Figure 6. RTPK
5. Auto-Start RTPK
Start RTK surveying in the Collect screen and wait un-
til the end of the Data Split Interval Auto-Start period
(Figure 7).
Figure 7. Collect screen
Aer surveying begins, the RTPK will process (Figure
8):
Figure 8. RTPK: post processing
www.javad.com 5
The end of the processing will display the result in the
form of graphs comparing the two solutions (Figure 9):
Figure 9. The results
6. Manual start RTPK
When the manual start of the RTPK is used, there are
the same procedures and results. The dierence is that
you can stop the survey and start RTPK processing
without waiting for automatic completion.
Stop the surveying and click RTPK in the white box to
start RTPK processing.
7. Checking RTPK results
On the Home screen, tap Points. Choose the processed
point and tap the Table icon on the top right (Figure
10):
Figure 10. Tap The Table icon
There are two solutions for one point (Figure 11,12).
Switch between them to choose the accuracy you
need.
Figure 11. Point solution 1
Figure 12. Point solution 2
900 Rock Avenue, San Jose,
CA 95131, USA
Phone: +1(408)770-1770
Fax : +1(408)770-1799
www.javad.com
All rights reserved © JAVAD GNSS, Inc., 2021
/