Soyal AR-727-CM HTTP Server Owner's manual

Brand: Soyal

Model: AR-727-CM HTTP Server

Category: Networking

Type: Owner's manual

This manual is also suitable for

AR-727-CM Device Network Server

System Requirements

SOYAL Website Software Download

Web Browser Setting Interface

Cross-Platform Services does not limit to particular operating

system, smartphone, or tablet

Setting Fire Alarm Auto Release Doors and TCP/IP Remote I/O

Control Setting

SOYAL Operation Manual

V230113

AR-727-CM

HTTP Server

Operation Manual

Table of Contents

References

HTTP Server

Introduction

1-1 Main Features ......................................................

1-2 Architecture Schematic Diagrams ........................

Interface Overview

2-1 Log in HTTP Server page .....................................

2-2 Device Connection Status ....................................

2-3 Network Setting ............................................

2-4 RS485 Parameter Setting .....................................

2-5 I/O Direct Control and Query .................................

3-1 TCP/IP Converter Setting .....................................

3-2 Fire Alarm Auto Release Doors .............................

3-2-1 Fire Alarm Auto Release Doors (RS485 method)

3-2-2 Fire Alarm Auto Release Doors (UDP method)

3-2-3 Fire Alarm Auto Release Doors

(RS-485 & UDP Dual-release)

3-2-4 Fire Alarm Auto Release Lift Door

3-2-5 Fire Alarm Indicator

3-3 TCP/IP Remote I/O Control Setting.......................

3-4 Server-Client Mode Communication Bridge..........

3-5 Change Login Password.......................................

4-1 FAQ .....................................................................

4-2 YouTube Videos....................................................

4-3 Firmware...............................................................

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

1. HTTP Server Introduction

1-1 Main Features

Easy setup via Smartphone, Tablet, and PC by entering IP address of the devices

through web browser

HTTP Server is compatible for SOYAL Enterprise Series (listed on separate

manual refer to ‘Operation Manual Enterprise Series HTTP Server’), SOYAL

Industry Series (TCP), AR-716-E18 Ethernet module AR-727i-V3 and Converter

AR-727-CM.

HTTP Server Comparison Table

Devices with DI/DO onboard, through HTTP Server could directly control and

monitor recent status of onboard DI/DO

Connect to Fire Detector Central Control when re alarm occurred, automatically

notied designated controller to open door

Establish a Server-Client connection bridge to extend wiring, limitless wiring

distance, or to provide wireless connection.

AR-727-CM-IO-0804M through its DI/DO features provides TCP to Wiegand

signal conversion, at the same time all of Industrial Series built-in Modbus

communication protocol that could easily works with third party integration of

Monitoring Software and SCADA.

Interface Menu Enterprise

Series

Industry Series (TCP)

AR-727-CM-0804M

AR-401-IO-0808R-U2

AR-727i-V3

(AR-716-E18

Ethernet module)

Converter

AR-727-CM

1Current State V V V V

2Network Setting V V V V

Controller Setting:

Event Log /User List /

Controller Parameter /

User Add/Change /

Timezone / Clock

4Login Password V V V V

RS485 Setting:

Channel 1 Setting /

Channel 2 Setting

V V

I/O Control Setting:

Direct Control IO 0~3 /

Direct Control IO 4~7

1. HTTP Server Introduction

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

ID:SuperAdm

PWD:721568

Remote setting by computer, Pad, Smartphone

Fire Alarm Output

(Dry Contact)

Modem

Power

Multi Functional Access Controller

AR-721-H

Fire Detector

Central Control

2-1

1-2

2. Interface Overview

Architecture Schematic Diagrams

1Through PC, Tablet, or Smartphone web browser software/app, enter device IP

Address and enter HTTP Server interface (default IP Address 192.168.1.127)

AR-727-CM-IO- 0804M

EHR05276005

13.57.043A7B

2. Interface Overview

To ensure the best connection quality, the maximum amount of the connection of Controller is

8 for each channel of AR-727-CM, so that the total amount is 16 Controllers.

Note :

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

When entering HTTP Server page required entering ID and Password. Default ID:

SuperAdm / Password: 721568 which can also be found on serial no. sticker that

include on the packaging.

(For older version, default ID: admin / password: admin)

Device Model no. and Firmware Version

After logged in, on the top right side will show the controller’s model no.

including the rmware version

After logged in, the rst menu that will automatically show Current State that will

indicate connection status

Connection Status can be seen between devices to HTTP Server (Port 80) and

device to 701Server (Port 1621 for Enterprise Series Controller or via AR-727-CM

CH1 / Port 1623 if via AR-727CM CH2)

2-2 Device Connection Status

2. Interface Overview

From the example above:

1. 192.168.001.078:(0080) CONNECTED -> indicated device with IP address 192.168.1.78

has connected to HTTP Server

2. 192.168.001.002:(1621) CONNECTED -> indicated device with IP address 192.168.1.2

has connected to 701Server

Note :

User Name is different from old and new version, password can be modify via [User Password]

setting on the list but will not be change from updating new version. If you forgot the password,

the solution is pressing Reset Button to reset it as default value.

Note :

Firmware Version User name Password (changeable)

After 2020/01/21 SuperAdm Default Password : 721568 or self-denition

Before 2020/01/21 admin Default Password : admin/ password not required or self-denition

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

2-3 Network Setting

ID:SuperAdm

PWD:721568

AR-727-CM-IO- 0804M

EHR05276005

13.57.043A7B

Product

serial number

MAC Address

Click the ‘Network Setting’ on the left side menu

Device Name: Rename network device, could be used to dierentiate between

one device and another

LAN IP Address: Enter IP address designated for the device of the intranet.

Default setting is 192.168.1.127

LAN Net Mask: Subnet Mask of the intranet

Default Gateway: Default gateway of the intranet.

if there is Internet connection access, this IP address must point to the router

or the gateway provided by the ISP

Primary DNS Server: Domain Name Server 1

Secondary DNS Server: Domain Name Server 2

MAC Address:Network physical address (this eld cannot be changed).

Each TCP/IP device has designated MAC address that could be found on the

serial number sticker

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

2-4 RS485 Parameter Setting

9HTTP Server Port: 80

Web browser service port, it can be change if there is information security

consideration but should not have the same TCP Port with 701Server connection

to devices which is 1621 or 1623

For Example: changing into 9680, to enter the HTTP Server you need to enter IP address

followed with Port

*the designated Port should be remembered all time, if not necessary to change the Port,

please let it remain default which is 80.

TCP/IP Control Port:

Setting of I/O Control Port.

Enter 1601 when using 727APP or mobile app connection

Enter 502 for Modbus communication protocol application

DHCP Client: Ticking this feature will enable dynamic host protocol which means

devices will automatically obtain IP address without manually typing and assigned

device to a designated IP address.

Update: Press Update button to save changed.

When you changed the LAN IP Address, after entering Update button, on the

browser eld required to type new IP address.

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Select ‘Channel 1 Setting’ to setup RS485 connection on Channel 1

Protocol: Choose TCP

Operation Mode: Server (Default)

Local Port:

Default Value 1621 (it is changeable to other Port but should not have the same

TCP Port with Server HTTP Port 80)

Remote Port: Default Value 1621, change into 0.

Remote IP: Set as 0.0.0.0

Note: Step no. 3-6 required a setup when applying Server-Client Mode connection bridge

(Refer to 3-3)

Baud Rate: Fixed value 9600

Data Bits: The added value of Data bits and Parity Bits, the default is (8) means 8

Data Bits and No Parity

For example: Serial Port Parameter Setting for 9600,0,8,1

AR-727-CM Data Bits set to 9 (the actual output will be 8 bit + 1 parity = 9), then set the

Parity into ‘Even’

Parity: Default Value None

Stop Bits:Default Value 1

Note: Step no. 7-10 required a setup when wiring to third party devices that have different

Serial Port Setting.

UART to NET delay time: Transmission delay time in milliseconds

UART to NET minimum bytes: Data transfer length default value 1024

(please do not change)

Socket Timeout: Time waiting for connection, set to 0 means to keep the

connection alive or keep alive (if it is unnecessary refrain from set up into 0)

Fire Alarm (DI0) Open Doors:

Enabling this feature will activate release all doors or specied doors under re

alarm event (triggered DI0 signal), only available under Server Mode

Door Open Mode:

Release lock mode, there are two options to choose 'Just-Pulse' or 'Keep Latch'.

Under a connection to Fire Alarm System, for safety purpose during Fire Event

select ‘Keep Latch’. For other purpose such as remote open door for visitor, select

‘Just-Pulse’.

2. Interface Overview

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Selected Node ID:

Select broadcast or specied group of doors to release lock under Fire Event

(each RS485 Channel could specied up to 8 doors).

Note: Step no.14-16 required a setup when applying Fire Alarm Auto Release Doors

(Refer to 3-2)

Update:

Press Update button to save changed.

IO Direct Control includes DI/DO direct and remote control over devices. This also

includes direct control of devices connected to Industry Series (TCP) over RS485.

‘Direct Control IO 0~3’

Direct control over DI0, DI1, DI2, DI3 and DO0, DO1, DO2, DO3

Direct control over RS485 CH1&CH2

‘Direct Control IO 4~7’

Direct control over DI4, DI5, DI6, DI7 and DO4, DO5, DO6, DO7

Direct control over RS485 CH1&CH2

Select Node: Enter broadcast or specified node ID to do control between Latch

Open(3)/Pulse Open(4)/Close(5) remotely on RS485 CH1&CH2.

Enter 255 to release doors for all controllers under RS485 CH1&CH2.

Enter specified node ID to control only one specific node ID under RS485 CH1.

(Example enter ‘Select Node 1’ means to do actions for Node ID 1 on RS485)

Action Control over RS485 CH1&CH2

2-5 I/O Direct Control and Query

6 7

8 9

2. Interface Overview

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Latch Open: Release lock continuously

Pulse Open: Release lock and lock automatically door relay time limit reached

(according to devices Door Relay Time Setting)

Close: Lock door

Press ‘Action’ to implement direct control from step 3-5.

Rename DI/DO:

Change the name of DI/DO and select ‘Name Change’ to save changed.

DI/DO Status:

The status change of DI/DO will be displayed here

DO Control:

Click ON to trigger DO, and click OFF to disable DO from triggering

Clicking ON for DO0, the DI status will automatically ON

Direct Control

0~3 for DI0~DI3

Direct Control 4~7

For DI4~DI7

Direct Control

0~3 for DO0~DO3

Direct Control 4~7

For DO4~DO7

DI/DO Status

DO Control DO Control

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Clicking OFF for DO0, the DI status will automatically returned to OFF status

DO Control (Output Time)

Change the Output Time of DO control between the range of 0~600 seconds.

Entering 0 means latch mode, output continuously.

Entering between 1~600 seconds means output ON according to output time set.

Update IO Status: Get real time IO current status by clicking Update IO Status

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

CH1 Setting:

CH2 Setting:

3-1 TCP/IP Converter Setting

Wiring SOYAL access controller to PC can be done via RS485 or TCP/IP interface.

For SOYAL access controller that built-in RS485, via Industry Series (TCP) or AR-

727-CM achieve RS485 to TCP/IP connection.

Each device built in two RS485 channels that dierentiate between CH1 and CH2.

Protocol : TCP

Operation Mode: Server

Local Port 1621

Default Value Protocol UDP change into TCP

Operation Mode: Server

Local Port 1623

3. Interface Overview

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

3-2 Fire Alarm Auto Release Doors

SOYAL provides various options for Fire Event Solution. This is taking a consideration of

onsite situation and human safety when escaping re and evacuation while maintaining

safety for authorized area.

Door Release Functions:(1) RS-485 automatically door release (2) UDP automatically

door release (3) RS-485 & UDP Dual-release

The functions above are all capable of self-dene function of (a) broadcast all controllers

or (b) release specic door only.

Note: Multi-door control panel AR-716-E16 only supports All-release function, please

utilize AR-727CM-IO or E series controller with TCPIO directly if you have assignment

requirement.

Releasing all doors is suggested for public spaces where user could directly escape

building for safety precaution and quick evacuation process. Meanwhile releasing only

a specied doors is suitable to keep doors remain locked for high authorized area or for

building with warehouses, treasure room, or server IT room.

3. Interface Overview

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

STEP 1 : Select CH1 Setting, conrming the Protocol is TCP mode

STEP 2 : Select CH1 Fire Release, conrming “Fire Alarm (DI0) Open Doors” is "Enable"

STEP 3 : Conrm “Door Open Mode” is "Keep-Latch"

STEP 4 : Assign the release door of re emergency procedure, each RS-485

Channel is capable of unlocking up to 8 doors.

(1) Release all doors under re event, input 255 in rst eld.

(2) Release assigned doors under re event, input assigned Node ID of the

controller in the elds.

STEP5. Press "Update"

● 3-2-1 Fire Alarm Auto Release Doors (RS485 method)

3. Interface Overview

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Parameter Setting:

Input 255 on rst eld to enable UDP

broadcast function and input 0 on the rest

of the elds, all electric locks connect with

the assigned channel will be released

immediately.

Release all doors

Parameter Setting:

Input the specied Node ID of controller in

elds, the electric locks will be released via

RS-485, remaining the safety of high security

area,optimizing emergency evacuation and

operator management.

Release specied doors only

● 3-2-2 Fire Alarm Auto Release Doors (UDP method)

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Compatibility: Enterprise series (E series) controller with TCPIP

Enterprise Series controller could accept “Release door lock” command via UDP

from any of the serial servers AR-727-CM-0804M or AR-401-IO-0808R-U2 (required

customized rmware, refer to Ref 3.)

The condition to this setup is only available for Enterprise Series Controller with

Ethernet connection and under the same intranet.

3. Interface Overview

STEP 1 : Enter the parameter setting page of controller on browser

STEP 2 : Select network setting

STEP 3 : Set up the "Secondary DNS Server"

(1) 0.0.0.0 : unlocked by any re detector in same intranet.

(2) 192.168.1.200 (self-dened IP) : unlocked by specied AR-727CM-IO.

Youtube Video Tutorial regarding

Fire Alarm Event Release All Doors

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

3. Interface Overview

● 3-2-3 Fire Alarm Auto Release Doors (RS-485 & UDP Dual-release)

Introduction:

This configuration could broadcast

plenty of controllers simultaneously, the

primary AR-727CM-IO could receive

fire input and broadcast door release

signal to secondary devices, including

AR-727CM-IO/AR-716-E16/E series

TCP controller.

Finally, the secondary devices will

transfer the door release signal to

the access controller via RS-485.

(parameter setting refer to 3-2-1)

Parameter Setting :

STEP 1 : Set the IP Address of primary AR-727CM-IO

STEP 2 : Enter the WEB page of AR-727CM-IO/AR-716-E16/E series controller

(1) AR-727CM-IO-0804M:

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

(2) AR-716-E16

(3) E Series Contoller

STEP 3 : Assign the release door of re event :

(1) AR-727CM-IO: Input 255 to release all doors or assign the specied

Node ID of controller. (details refer to 3-2-1)

(2) AR-716-E16: All H/E series controllers connect to AR-716-E16 will be

released automatically, not required to assign the controller.

(3) E series controller: E series controller with TCP could be assigned with

xed IP of primary AR-727CM-IO as individual re signal input.

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

3. Interface Overview

● 3-2-5 Fire Alarm Indicator

Indicator when Fire Alarm Event is happening:

DI0 LED will continuous blinking > sensing Fire Alarm Event

CH1 or/and CH2 TX red LED will fast blink > Release doors

Under AR-727CM-IO, the lift access controller supports connection to Fire Alarm. With

special rmware, in normal situation, when users swipe RFID tags, the controller’ s relay

doesn’t act. It only acts once receiving re alarm signal. Relay is controlled by re alarm

signal instead of valid tags.

This function is available at the rmwares:

725E-V2: APS725Ev2__V0403_200415 ACCESS_DONT_OPEN_DOOR.STM

725HD: 725HD_7V3 190530 ACCESS_DONT_OPNE_DOOR.ISP

● 3-2-4 Fire Alarm Auto Release Lift Door

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

3. Interface Overview

3-3 TCP/IP Remote I/O Control Setting

Remote I/O Control Setting is a function where when DI is triggered, the DO with

linkage control will control remote device or sending a warning (i.e: if temperature

in a factory is too high, it will send alert to AR-727CM-IO, the network linking to a

remote fan that connected to AR-727CM-IO too, will activate ventilation system and

send an alarm to Emergency Status Board in Main Factory).

Conditions:

Both serial servers AR-727-CM-0804M or AR-401-IO-0808R-U2 that will operate

interlinkage IO control must be on intranet or the same subnet mask, or implement

connection using VPN.

Required customize rmware for this feature (refer to Ref 4.)

One-to-one control, xed direction control

Serial

Server A →Serial

Server B

DI0 →DO0

DI1 →DO1

DI2 →DO2

DI3 →DO3

SOYAL TECHNOLOGY CO., LTD

SOYAL Operation Manual

AR-727-CM HTTP Server

Page is loading ...

Soyal AR-727-CM HTTP Server Owner's manual

Brand: Soyal

Model: AR-727-CM HTTP Server

Category: Networking

Type: Owner's manual

This manual is also suitable for

AR-727-CM Device Network Server

Download PDF

report

Soyal AR-727-CM HTTP Server Owner's manual

This manual is also suitable for

Soyal AR-727-CM HTTP Server Owner's manual

Related papers

Other documents