Artesyn MVME51005E Installation and Use Manual

MVME51005E Single Board Computer

Installation and Use

P/N: 6806800A38D

July 2014

Trademarks

Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of

property of their respective owners.

Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.

Java™ and all other Java-based marks are trademarks or registered trademarks of Oracle America, Inc. in the U.S. and other countries.

Microsoft®, Windows® and Windows Me® are registered trademarks of Microsoft Corporation; and Windows XP™ is a trademark of

Microsoft Corporation.

PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the PCI

Industrial Computer Manufacturers Group.

UNIX® is a registered trademark of The Open Group in the United States and other countries.

Notice

While reasonable efforts have been made to assure the accuracy of this document, Artesyn assumes no liability resulting from any

omissions in this document, or from the use of the information obtained therein. Artesyn reserves the right to revise this document

and to make changes from time to time in the content hereof without obligation of Artesyn to notify any person of such revision or

changes.

Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to

an Artesyn website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise

altered without the permission of Artesyn.

It is possible that this publication may contain reference to or information about Artesyn products (machines and programs),

programming, or services that are not available in your country. Such references or information must not be construed to mean that

Artesyn intends to announce such Artesyn products, programming, or services in your country.

Limited and Restricted Rights Legend

If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply

unless otherwise agreed to in writing by Artesyn.

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in

Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and

Documentation clause at DFARS 252.227-7014 (Jun. 1995).

Contact Address

Artesyn Embedded Technologies Artesyn Embedded Technologies

Marketing Communications Lilienthalstr. 17-19

2900 S. Diablo Way, Suite 190 85579 Neubiberg/Munich

Tempe, Arizona 85282 Germany

Contents

MVME51005E Single Board Computer Installation and Use (6806800A38D) 3

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1 Hardware Preparation and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.1.2 Overview and Equipment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1.1.3 Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1.2 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1.2.1 Hardware Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1.2.2 Jumper Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

1.2.2.1 PMC/SBC (761/IPMC) Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

1.2.3 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

1.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

1.3.1 PMC Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

1.3.2 Primary PMCspan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

1.3.3 Secondary PMCspan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1.3.4 MVME5100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.2 Switches and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.2.1 ABT/RST Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.2.1.1 Abort Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.2.1.2 Reset Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

2.2.2 Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.2.2.1 RST Indicator (DS1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.2.2.2 CPU Indicator (DS2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.2.3 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.2.3.1 10/100BASE T Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2.2.3.2 DEBUG Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

2.3 System Powerup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

2.3.1 Initialization Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Contents

MVME51005E Single Board Computer Installation and Use (6806800A38D)

Contents

4

Contents

3 PPCBug Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.2 PPCBug Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.2.1 Implementation and Memory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

3.3 Using PPCBug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3.3.1 Hardware and Firmware Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.4 Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

3.4.1 CNFG - Configure Board Information Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

3.4.2 ENV - Set Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

3.4.2.1 Configuring the PPCBug Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

3.4.3 LED/Serial Startup Diagnostic Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

3.4.4 Configuring the VMEbus Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

3.4.5 Firmware Command Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

3.5 Standard Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

3.5.1 Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

4.2 Features Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

4.3 Features Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

4.3.2 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.3.3 System Memory Controller and PCI Host Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.3.4 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.3.4.1 Flash Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4.3.4.2 ECC SDRAM Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

4.3.5 P2 Input/Output (I/O) Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

4.3.6 Input/Output Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

4.3.6.1 Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

4.3.6.2 VMEbus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

4.3.6.3 Asynchronous Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

4.3.6.4 Real-Time Clock & NVRAM & Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 74

4.3.6.5 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

4.3.6.6 Interrupt Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

4.3.6.7 IDSEL Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Contents

MVME51005E Single Board Computer Installation and Use (6806800A38D) 5

5 RAM500 Memory Expansion Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

5.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

5.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

5.3.1 RAM500 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

5.3.2 SROM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

5.4 RAM500 Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

5.5 RAM500 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

5.5.1 Bottom Side Memory Expansion Connector (P1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

5.6 RAM500 Programming Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

5.6.1 Serial Presence Detect (SPD) Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

6 Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

6.1.1 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

6.2 Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

6.3 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

6.3.1 IPMC761 Connector (J3) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

6.3.2 Memory Expansion Connector (J8) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

6.3.3 PCI Expansion Connector (J25) Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

6.3.4 PCI Mezzanine Card (PMC) Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

6.3.5 VMEbus Connectors P1 & P2 Pin Assignments (PMC mode). . . . . . . . . . . . . . . . . . . . . . . 109

6.3.6 VMEbus P1 & P2 Connector Pin Assignments (SBC Mode) . . . . . . . . . . . . . . . . . . . . . . . . 111

6.3.7 10 BaseT/100 BaseTx Connector Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

6.3.8 COM1 and COM2 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

7 Programming the MVME5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

7.2 Memory Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

7.2.1 Processor Bus Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

7.2.1.1 Default Processor Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

7.2.1.2 Processor Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

7.2.1.3 PCI Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

7.2.1.4 VME Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

MVME51005E Single Board Computer Installation and Use (6806800A38D)

Contents

6

Contents

7.2.2 PCI Local Bus Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

7.2.3 VMEbus Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

7.3 Programming Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

7.3.1 PCI Arbitration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

7.3.2 Interrupt Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

7.3.3 DMA Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

7.3.4 Sources of Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

7.3.5 Endian Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

7.3.5.1 Processor/Memory Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

7.3.5.2 PCI Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

7.3.5.3 VMEbus Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

A Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

A.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

A.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

A.3 Cooling Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

A.4 EMC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

B Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

B.1 Solving Startup Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

C Thermal Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

C.1 Thermally Significant Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

C.2 Component Temperature Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

C.2.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

C.2.2 Measuring Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

C.2.3 Measuring Case Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

C.2.4 Measuring Local Air Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

D Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

D.1 Artesyn Embedded Technologies - Embedded Computing Documentation . . . . . . . . . . . . . . . 147

D.2 Manufacturer’s Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

D.3 Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

List of Figures

MVME51005E Single Board Computer Installation and Use (6806800A38D) 7

Figure 1-1 MVME5100-Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 1-2 MVME5100 Installation and Removal From a VMEbus Chassis . . . . . . . . . . . . . . . . . 29

Figure 1-3 Typical PMC Module Placement on an MVME5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 1-4 PMCspan16E-010 Installation on a PMCspan16E-002 . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 2-1 Boot-Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 4-1 MVME5100 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 5-1 RAM500 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Figure 7-1 VMEbus Master Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Figure 7-2 MVME5100 Interrupt Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Figure C-1 Thermally Significant Components on the MVME5100 SBC - Primary Side . . . . . 142

Figure C-2 Thermally Significant Components on the IPMC761 Module - Primary Side . . . . 143

Figure C-3 Mounting a Thermocouple Under a Heatsin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Figure C-4 Measuring Local Air Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

MVME51005E Single Board Computer Installation and Use (6806800A38D)

8

List of Figures

List of Tables

MVME51005E Single Board Computer Installation and Use (6806800A38D) 13

Table 1-1 Manually Configured Headers/Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 3-1 Debugger Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Table 3-2 Diagnostic Test Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Table 4-1 MVME5100 General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Table 5-1 RAM500 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Table 5-2 RAM500 SDRAM Memory Size Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Table 5-3 RAM500 Bottom Side Connector (P1)Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Table 6-1 IPMC761 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Table 6-2 RAM500 Bottom Side Connector (P1)Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Table 6-3 RAM500 Bottom Side Connector (P1)Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Table 6-4 PMC Slot 1 Connector (J11) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Table 6-5 PMC Slot 1 Connector (J12) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Table 6-6 PMC Slot 1 Connector (J14) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Table 6-7 Pin Assignments for Connector P2 in PMC Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Table 7-1 Default Processor Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Table 7-2 Suggested CHRP Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Table 7-3 Hawk PPC Register Values for Suggested Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Table 7-4 PCI Arbitration Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Table 7-5 Devices Affected by Various Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Table A-1 MVME5100 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Table A-2 Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Table B-1 Troubleshooting Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Table C-1 Thermally Significant Components on the MVME5100 Single Board Computer . . . . . . . 139

Table C-2 Thermally Significant Components on the IPMC761 Module . . . . . . . . . . . . . . . . . . . . . . . . 140

Table D-1 Artesyn Embedded Technologies - Embedded Computing Publications . . . . . . . . . . . . . 147

Table D-2 Manufacturers’ Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Table D-3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

MVME51005E Single Board Computer Installation and Use (6806800A38D)

14

List of Tables

MVME51005E Single Board Computer Installation and Use (6806800A38D) 15

About this Manual

Overview of Contents

The MVME51005E Single Board Computer Installation and Use provides the information you will

need to install and configure your MVME51005E Single Board Computer. It provides specific

preparation and installation information and data applicable to the board

. The MVME51005E

will hereafter be referred to as the MVME5100.

The MVME5100 is a high-performance VME single board computer featuring the PowerPlus II

architecture with a choice of processors—either the MPC7410 with AltiVec™ technology for

algorithmic intensive computations or the low-power MPC750.

As of the printing date of this manual, the MVME5100 is available in the configurations shown

below. Note: all models of the MVME5100 are available with either VME Scanbe front panel or

IEEE 1101 compatible front panel handles.

Model Number Description

450MHz MCP750 Commercial Models

MVME51005E-016x 450MHz MCP750, 512MB ECC SDRAM, 17MB Flash and

1MB L2 cache.

400 and 500 MHz MPC7410 Commercial Models

MVME51105E-216x 400MHz MPC7410, 512MB ECC SDRAM, 17MB Flash and

2MB L2 cache.

MVME51105E-226x 500 MHz MPC7410, 512MB ECC SDRAM, 17MB Flash and

2MB L2 cache

MVME712M Compatible I/O

IPMC7126E-002 Multifunction rear I/O PMC module; 8-bit SCSI, Ultra

Wide SCSI, one parallel port, three async and one

sync/async serial port.

MVME712M6E Transition module connectors: One DB-25 sync/async

serial port, three DB-25 async serial ports, one AUI

connector, one D-36 parallel port, and one 50-pin 8-bit

SCSI; includes 3-row DIN P2 adapter module and cable.

MVME761 Compatible I/O

IPMC7616E-002 Multifunction rear I/O PMC module; 8-bit SCSI, one

parallel port, two async and two sync/async serial ports.

MVME51005E Single Board Computer Installation and Use (6806800A38D)

About this Manual

16

About this Manual

Chapter 1, Hardware Preparation and Installation, provides a description of the MVME5100 and

its main integrated PMC and IPMC boards. The remainder of the chapter includes an

explanation of the installation procedure, including preparation and jumper setting

information.

MVME7616E-001 Transition module: Two DB-9 async serial port

connectors, two HD-26 sync/async serial port

connectors, one HD-36 parallel port connector, and one

RJ-45 10/100 Ethernet connector; includes 3-row DIN P2

adapter module and cable (for 8-bit SCSI).

MVME7616E-011 Transition module: Two DB-9 async serial port

connectors, two HD-26 sync/async serial port

connectors, one HD-36 parallel port connector, and one

RJ-45 10/100 Ethernet connector; includes 5-row DIN P2

adapter module and cable (for 16-bit SCSI); requires

backplane with 5-row DIN connectors.

SIM232DCE5E or DTE EIA-232 DCE or DTE Serial Interface Module.

Related Products

PMCSPAN26E-002 Primary PMCSPAN with original VME Scanbe ejector

handles.

PMCSPAN26E-010 Secondary PMCSAN with original VME Scanbe ejector

handles.

RAM5005E-006 Stackable (top) 256MB ECC SDRAM mezzanine.

RAM5005E-016 Stackable (bottom) 256MB ECC SDRAM mezzanine.

RAM5005E-010 Stackable (top) 512MB ECC SDRAM mezzanine.

RAM5005E-020 Stackable (bottom) 512MB ECC SDRAM mezzanine.

RAM5006E-005 Stackable (top) 128MB ECC DRAM

RAM5006E-015 Stackable (bottom) 128MB ECC DRAM

RAM5006E-006 Stackable (top) 256MB ECC DRAM

RAM5006E-016 Stackable (bottom) 256MB ECC DRAM

RAM5006E-010 Stackable (top) 512MB ECC DRAM

RAM5006E-020 Stackable (bottom) 512MB ECC DRAM

About this Manual

MVME51005E Single Board Computer Installation and Use (6806800A38D) 17

Chapter 2, Operation, provides a description of the operational functions of the MVME5100

including tips on applying power, a description of the switch settings, the status indicators, I/O

connectors, and system power up information.

Chapter 3, PPCBug Firmware, provides an explanation of the debugger firmware, PPCBug, on

the MVME5100. The chapter includes an overview of the firmware, a section on how to use

PPCBug, a listing of the initialization steps, a brief explanation of the two main configuration

commands CNFG and ENV, and a description of the standard configuration parameters. A

listing of the basic commands are also provided.

Chapter 4, Functional Description, provides a summary of the MVME5100 features, a block

diagram, and a description of the major functional areas.

Chapter 5, RAM500 Memory Expansion Module, provides a description of the RAM500 Memory

Expansion Module, a list of features, a block diagram of the module, a table of memory size

allocations, an installation procedure, and pinouts of the module’s top and bottom side

connectors.

Chapter 6, Pin Assignments, provides a listing of all connector and header pin assignments for

the MVME5100.

Chapter 7, Programming the MVME5100, provides a description of the memory maps on the

MVME5100 including tables of default processor memory maps, suggested CHRP memory

maps and Hawk PPC register values for suggested memory maps. The remainder of the

chapter provides some programming considerations.

Appendix A, Specifications, provides the standard specifications for the MVME5100, as well as

some general information on cooling.

Appendix B, Troubleshooting, provides a brief explanation of the possible resolutions for basic

error conditions.

Appendix C, Thermal Analysis, gives systems integrators the information necessary to conduct

thermal evaluations of the board in their specific system configuration.

Appendix D, Related Documentation, provides a listing of related documentation for the

MVME5100, including vendor documentation and industry related specifications.

MVME51005E Single Board Computer Installation and Use (6806800A38D)

About this Manual

18

About this Manual

Abbreviations

This document uses the following abbreviations:

Term Meaning

AAmpere

ANSI American National Standard Institute

BLT Block Transfer

CFM Cubic Feet per Minute

CMC Common Mezzanine Card

COM Communications

COP Common On-chip Processor

CPU Central Processing Unit

DDR Double Data Rate

°C Degree Celsius

DMA Direct Memory Access

DRAM Dynamic Random Access Memory

DUART Dual Universal Asynchronous Receiver/Transmitter

ECC Error Correction Code

EEPROM Electrically Erasable Programmable Read-Only Memory

FCC Federal Communications Commission

FIFO First In First Out

GB Gigabytes

Gbit Gigabit

Gbps Gigabits Per Second

GPCM General Purpose Chip select Machine

H/W Hardware

IEEE Institute of Electrical and Electronics Engineers

I2C Inter IC

JTAG Joint Test Access Group

About this Manual

MVME51005E Single Board Computer Installation and Use (6806800A38D) 19

KB Kilobytes

KBAUD Kilo Baud

LBC Local Bus Controller

LED Light Emitting Diode

MB Megabytes

Mbps Megabits Per Second

MHz Megahertz

NAND (Not and) Flash that is used for storage

NOR (Not or) Flash that is used for executing code

OS Operating System

PCI Peripheral Component Interconnect

PCI-X Peripheral Component Interconnect -X

PIC Programmable Interrupt Controller

PIM PCI Mezzanine Card Input/Output Module

PMC PCI Mezzanine Card (IEEE P1386.1)

PLD Programmable Logic Device

QUART Quad Universal Asynchronous Receiver/Transmitter

RAM Random Access Memory

RGMII Reduced Gigabit Media Independent Interface

RTC Real-Time Clock

RTM Rear Transition Module

SBC Single Board Computer

SDRAM Synchronous Dynamic Random Access Memory

SMT Surface Mount Technology

SODIMM Small-Outline Dual In-line Memory Module

SPD Serial Presence Detect

SoC System-on-Chip

SRAM Static Random Access Memory

Term Meaning

MVME51005E Single Board Computer Installation and Use (6806800A38D)

About this Manual

20

About this Manual

Conventions

The following table describes the conventions used throughout this manual.

S/W Software

TSEC Three-Speed Ethernet Controller

2eSST Two edge Source Synchronous Transfer

UART Universal Asynchronous Receiver/Transmitter

V Volts

VIO Input/Output Voltage

VITA VMEbus International Trade Association

VME Versa Module Eurocard

VPD Vital Product Data

W Watts

Term Meaning

Notation Description

0x00000000 Typical notation for hexadecimal numbers (digits are

0 through F), for example used for addresses and

offsets

0b0000 Same for binary numbers (digits are 0 and 1)

bold Used to emphasize a word

Screen Used for on-screen output and code related elements

or commands in body text

Courier + Bold Used to characterize user input and to separate it

from system output

Reference Used for references and for table and figure

descriptions

File > Exit Notation for selecting a submenu

<text> Notation for variables and keys

[text] Notation for software buttons to click on the screen

and parameter description

About this Manual

MVME51005E Single Board Computer Installation and Use (6806800A38D) 21

Summary of Changes

... Repeated item for example node 1, node 2, ..., node

12

.

Omission of information from example/command

that is not necessary at the time being

.. Ranges, for example: 0..4 means one of the integers

0,1,2,3, and 4 (used in registers)

| Logical OR

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury

Indicates a hazardous situation which, if not avoided,

may result in minor or moderate injury

Indicates a property damage message

No danger encountered. Pay attention to important

information

Notation Description

Part Number Publication Date Description

6806800A38D July 2014 Re- branded to Artesyn template.

MVME51005E Single Board Computer Installation and Use (6806800A38D)

About this Manual

22

About this Manual

Chapter 1

MVME51005E Single Board Computer Installation and Use (6806800A38D) 21

Hardware Preparation and Installation

1.1 Introduction

This chapter provides information on hardware preparation and installation for the MVME5100

Series of Single Board Computers.

Note: Unless otherwise specified, the designation “MVME5100” refers to all models of the

MVME5100-series Single Board Computers.

1.1.1 Getting Started

The following subsections include information helpful in preparing your equipment. It includes

and overview of the MVME5100, any equipment needed to complete the installation, and

unpacking instructions.

1.1.2 Overview and Equipment Requirements

The MVME5100 interfaces to a VMEbus system via its P1 and P2 connectors and contains two

IEEE 1386.1 PCI Mezzanine Card (PMC) Slots. The PMC Slots are 64-bit and support both front

and rear I/O.

Additionally, the MVME5100 is user configurable by setting on-board jumpers. Two I/O modes

are possible: PMC mode or SBC mode (also called 761 or IPMC mode). The SBC mode uses the

IPMC712 I/O PMC and the MVME712M Transition Module, or the IPMC761 I/O PMC and the

MVME761 Transition Module. The SBC mode is backwards compatible with the MVME761

transition card and the P2 adapter card (excluding PMC I/O routing) used on the

MVME2600/2700 product. This mode is accomplished by configuring the on-board jumpers

and by attaching an IPMC761 PMC in PMC slot 1. Secondary Ethernet is configured to the rear.

PMC mode is backwards compatible with the MVME2300/MVME2400 and is accomplished by

simply configuring the on-board jumpers.

The following equipment list is appropriate for use in an MVME5100 system:

1. PMCspan PCI expansion mezzanine module (mates with MVME5100)

2. Peripheral Component Interconnect (PCI) Mezzanine Cards (PMCs) (installed on an

MVME5100 board)

3. RAM500 memory mezzanine modules (installed on an MVME5100 board)

4. VME system enclosure

Hardware Preparation and Installation

MVME51005E Single Board Computer Installation and Use (6806800A38D)

22

5. System console terminal

6. Disk drives (and/or other I/O) and controllers

7. Operating system (and/or application software)

1.1.3 Unpacking Instructions

Note: A system chassis may not be a suitable grounding source if it is unplugged.

Avoid touching areas of integrated circuitry; static discharge can damage these circuits.

Artesyn strongly recommends that you use an antistatic wrist strap and conductive foam

pad when installing or upgrading a system.

Electronic components, such as disk drives, computer boards and memory modules, can be

extremely sensitive to electrostatic discharge (ESD). After removing the component from

its protective wrapper or from the system, place the component on a grounded, static-free,

and adequately protected working surface. Do not slide the component over any surface. In

the case of a Printed Circuit Board (PCB), place the board with the component side facing

up.

If an ESD station is not available, you can avoid damage resulting from ESD by wearing an

anti-static wrist strap (available locally) that is attached to an active electrical ground.

Page is loading ...

Artesyn MVME51005E Installation and Use Manual

Related papers

Other documents