1241098-2A-C 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. If possible, install this faucet before installing the lavatory.
3. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
4. Observe local plumbing codes.
5. Shut off the water supplies to the fitting.
1241098-2A-C 4
INSTALLATION INSTRUCTIONS
99856T-4 Single Handle Lavatory Faucet
99858T-4 Single Handle Tall Lavatory Faucet
99856T-4 Single Handle Lavatory Faucet
99858T-4 Single Handle Tall Lavatory Faucet
BEITOUBEITOU
HANDLE OPERATION
Lift handle gently. Turn clockwise for cold water, turn counter-colckwise for hot water.
ROUGH-IN DIMENSIONS
SERVICE PARTS
99858T-4
**Color code must be specified when ordering.
1228831**
1258102
1258105
1032559
1123942
1223368
1080817
1228836
99856T-4: 834754
99858T-4: 880096
1258089
870654
1223584 1223593
1223587**
12235861223585**
1258091
1258090
1231860
1234008
3008523
3013706
1142103**
1102890**
1102891
1102892
833730
1228834
Ø33~Ø38
144
387.5
105
117.5
222
G1/2˝
188~200
Ø69
Ø60
Ø41.2
27~60
Ø31.75
112
272.9
46
Min.30
Max.35
1241098-2A-C 2
1241098-2A-C 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
CARE AND MAINTENANCE
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Faucet
Install the mounting stud(2) into the faucet body
base(3). Install the washer(4) into the groove at the
bottom of the faucet body.
Insert the faucet assembly into the lavatory hole.
Position the faucet. From underside of the lavatory,
place the bracket(5, Rubber washer is on the top)
onto the mounting stud, and secure the faucet with
the nut(6) by tool(7).
Attach the hoses(1) to water supplies, the hose with
"COLD" label connects to cold water.
Clean Rectifier
If there is a lot of debris in the supply pipes or the
quality of water is bad, it will cause the flow in bad
condition. Please clean the filter as following steps:
Turn off the faucet. Take out the plugs(18), remove
the screws(19) with hex wrench(17). Uninstall the
spout(20) from body(24). Remove the flange(21),
rectifier(22) and O-ring(23).
Flush the filter of rectifier. Check the filter whether is
intact, if damaged replace it.
Reassemble the spout and body: put the O-ring,
rectifier and flange into the original position. Install
the spout onto body and tighten the screws. Insert
the plugs.
How to Install the Drain
Remove the locknut(8), plastic washer(9), rubber
gasket(10) and tailpiece(11) from the drain body.
Supply enough tape or sealant to tailpiece thread.
Reinstall the tailpiece. Insert the drain body into the
lavatory. Install the rubber gasket (Tapered side up),
plastic washer and locknut back to the drain body in
turn. Tighten the locknut.
NOTE: If needed, apply a ring of plumbers putty or
other sealants around the underside of the drain
flange(12), instead of using rubber washer(13).
Do not reposition the drain after the locknut is
tightened, or you may break the putty or sealant
seal.
Ensure that all connections are tight. Ensure that the
handle is in the off position.
Turn on the drain and main water supply, and check
for leaks. Repair as needed.
Replacing the Washer and Piston Kit
Turn counter-clockwise to remove the stopper(14).
Take out washer(15). Replace with a new one. Turn
counter-clockwise to remove the piston kit(16).
Replace with a new one. Reinstall stopper and
washer.
Drain Body
99856T-4
12
13
11
10
9
8
Min.30
88
117.5
46
144
Ø33~Ø38
37.2
Max.35
384
105
G1/2˝
188~200
Ø69
Ø60
Ø41.2
27~60
Ø31.75
112
3
1
4
5
2
6
7
14
15
16
17
20
21
22
18 19
23
24
/