Gas
Models:
Installation
Cooktop
SGM304, SGM365, SGM466
Instructions
Pa_ No. 65141 Rev. L
Important Safety Instructions .......................................... 1
Important Information About Safety Instructions .............. 1
General Safety Precautions ............................................. 2
Installation Specifications ................................................ 3
Product Dimensions ......................................................... 3
Electrical Requirements ................................................... 4
Gas Supply Requirements ............................................... 4
Cabinet and Countertop Layout ....................................... 5
Installation Instructions .................................................... 8
Verify Package Contents .................................................. 8
Installing the Cooktop ...................................................... 8
Connecting the Gas Line ................................................. 8
Installing the Burner Components .................................... 9
Verifying Proper Operation ............................................... 9
Installation Checklist ...................................................... 10
Parts List ......................................................................... 11
Wiring Diagrams .............................................................. 12
important:
• Installer: In the interest of safety and to minimize problems, read these installation instructions completely and care-
fully before you begin the installation process. Leave these installation instructions with the customer.
• Customer: Keep these installation instructions for future reference and the local electrical inspector's use.
NOTE: Dacor ®is not responsible for service required to correct a faulty installation.
If You Need Help... Product Data Label
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team. For
repairs to Dacor appliances under warranty call the Dacor
Distinctive Service line. Whenever you call, have the model .
and serial number of the appliance ready. The model and
serial number are printed on the product data label.
Dacor Customer Service
Phone: (800) 793-0093 (U.S.A. and Canada)
Monday -- Friday 6:00 A.M. to 5:00 P.M. Pacific Time
Web site: www.Dacor.com
Dacor Distinctive Service (repairs under warranty only)
Phone: (877) 337-3226 (U.S.A. and Canada)
Monday -- Friday 6:00 A.N. to 4:00 P.N. Pacific Time
The product data label contains the model and serial
number information and the electrical and gas supply
requirements.
It is attached to the chassis on the bottom of the unit.
Front of unit
\
Product data
label
All specifications are subject to change without notice. Dacor assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.
Important Information About
SafeLyInstructions
The important Safety instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or oper-
ating this or any other appliance.
• Always contact the Dacor Customer Service Team
about problems and conditions that you don't under-
stand. See Customer Service information.
DANGER
MPORTANT: tf y0U smell gasi
Donot Useor light any appliancel
, Do not touch any e[ectricaJ switch or use any e[ectri-
ca[deviceS; including the te[eph0ne; in YoUr bujldingl
From a neighborls phone; immediately cal! the gas
supplier Followthe gas supp ier,s instructions:
, If Y0Ucannot contact the gas Supplier, call the fire
department:
Safety Symbols and Labels
[ _ DANGER _ ]
mmed!atehazardSthatW LL
I injury or death. [
WARNING
HaZards or UnSafe practices that COULD result in SeVere
personal injury or death.
CAUTION
Hazards or unsafe practices that COULD result in minor
perSonal injury Or property damage:
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN
THE EVENT OF A RANGE TOP GREASE FIRE:
a; SMOTHER FLAMESwith a close-fitting lid; cookie
sheet 0r metal tray: then turn off the burner: BE
CAREFUL TO PREVENT BURNS: If the flames do
not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
b: NEVER PICK UPA FLAMING PAN : you maybe
burned!
c: DO NOT USE WATER; inc uding wet dish cloths or
t0wels : a Vi01entsteam explosion may resulL
Use a fire extingUiSher ONLY if:
O You have a Class ABC extinguisher, and you
already know h0w t0 0perate iL
The fire is small and contained in the area where
it startedl
fire department is being
0 You can fight the fire w!th y0ur back to an exit.
DANGER
IMPORTANT: Do not store or use combustibJe flammable
orexplosiveVaporsand,qU dS(suchasgaso,ne)onor
in the vicinity of this or any other appliancel Also keep
items that could explode, such as aerosol cans, away
fromthec0oktopD0notSt0ref_ammabSeorexplosive
materials in adjacent cabinets or areas (including above
and bel0w the co0ktop)i
WARNING
WARNING _ NEVER USeth!s appliance as a Space
heater to heat or warm the r0om:Doing so may result
in carbon monoxide poisoning and Overheating 0fthe
appliance.
[_ WARNING
WARNING - NEVER cover any slots, holes or passages
on the cooktop and cooktop chassis. Doing so blocks
air flow through the cooktop and may cause carbon
monoxide poisoning. Aluminum foil linings may also trap
heat, causing a fire hazard. Keep all slots, holes and
passages clear of grease and grime.
CALIFORNIA PROPOSITION 65
WARNING
The burning of gas cooking fuel generates some
by-products that are on the list of substances which
are known by the State of California to cause cancer or
reproductive harm. California law requires businesses
to warn customers of potential exposure to such
substances. To minimize exposure to these substances,
always operate this unit according to the use and care
manual, ensuring you provide good ventilation when
cooking with gas.
READ AND SAVE THESE INSTRUCTIONS
_a_D_ 1
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau-
tions, including the following:
WARNING
• Read the accompanying use and care manual com-
pletely before operating this appliance.
- Keep packaging materials away from children.
Plastic sheets and bags can Cause suffocation.
- If you receive a damaged proauct, immediately con-
tact your dealer or builder. Do not install or use a
damaged appliance.
- This cooktop must be properly installed and ground-
ed by a qualified installer according to these instal-
lation instructions prior to use. The installer should
show the customer the location of the gas shut off
valve and the power cord so that they know where
and how to turn off the gas supply and disconnect
power to the cooktop.
- Do not use this appliance in combination with a sur-
face (countertop) ventilation system. Dacor strongly
recommends the installation of a range hood in con-
junction with this appliance.
• Do not install, repair or replace any part of the
cooktop unless specifically recommended in the liter-
ature accompanying it. A qualified service technician
should perform all other service.
- Before servicing or installingthis cooktop, make sure
that the gas supply is turned off at the gas supply
valve and that the power plug is disconnected from
the electrical outlet.
- Disconnect the power plug from the electrical outlet
before cleaning. Clean this appliance only in the
manner specified in the use and care manual.
° Only use the cooktop for cooking tasks expected of
a home appliance as outlined in the literature accom-
panying it. This cooktop is not intended for commer-
cial or laboratory use.
- DO NOT TOUCH THE SURFACES OF THE
COOKTOP DURING OR IMMEDIATELY AFTER
USE.
- Do not operate this appliance if the power cord is
damaged.
- Turn the knobs to the OFF position prior to removing
them from the valve stems.
• To avoid a fire hazard, do not hang flammable or
heat sensitive objects over the cooktop.
- Do not climb on any part of the appliance.
WARNING
' Do not leave children alone Orunattended in the
area around the cooktop: Do not a!low ch dren to
play with the controls or touch other parts of the
CooktOpl DOnot store items of interest to children
on tOP of orabove the cooktOpl Children could be
burned or injured while climbing on the appliance:
Clean 0perating itfor
the first time: Make sure that allthe cooktop parts
are dry before lighting a burnerl
' Keep flammable itemsl Such as Paper' Oardboardl
plastic and cloth away from the burners and other
hot SUrfaces: Do not place such itemS Onthe
cooktop DO not alloW pot holders to touch hot sur:
faces Or gas burnersl
' DO not wear loose Or hanging apparel While us!ng
the cooktopl Do not allOWclothing to come into con-
tact w th the €Ooktop and surrounding areas during
and immediatelY after use:
Do not use towels or bulky cloth as pot holders:
- Do not USe the cookteP tO heat sealed container s:
The container and contents may explode, causing
personal injury.
; the CooktoP is near a Window IdO not Use long cur-
tains as window treatment. The curtains could blow
over the €ooktop and create a fire hazard!
* Non-stick coatings; When heatedl can be harmful to
birds: RemOve birds to a Separate, Well;ventilated
room when operating the cooktop_
IMPORTANT: This appliance _ ________
is equipped with a three' / _ S|--_ii-: 1
Prong grounding plug for you[
protection against possible /
electric shock hazardsl Plug it
/
customer to make sure the proper type of outlet is
installed: Do not under any circumstances:
Cut or remove the third (ground)prong from the
power cord:
' uSe an adapter plUgl
; Use an extension cordl
' Use POWercord that iS flayed or damaged:
-Connect to an electiical 0utlet with a ground fault
interrupter (GFI).
2 _8C0_
[_ WARNING I
observe all governing Codes and Ordinances during planning and installation: Contact your local building department for I
further information. I
Product Dimensions
All tolerances +1/16" (+1.6 mm) unless otherwise noted.
1 5/8" (4.1 cm)
bottom of base
30" _ to cooking surface
(76.2 cm)
_ /_ 4" (10.2 cm)
.._ _ chassis height
/
Model SGM304
z-, 27 5/8"*
19 1/2"* (70.2 cm)
\ 21" (49.5 cm) /
(53.3 cm)
* including embosses/screws in side of chassis
36"
(91.4 cm)
/
* including embosses in side of chassis
33 1/2" *
(85.1 cm)
46"
(116.8 cm)
1 5/8" (4.1 cm)
bottom of base
to cooking surface
/,_ 4" (10.2 cm)
_chassis height
Model SGM365
4" (10.2 cm)
chassis height
1 5/8" (4.1 cm)
bottom of base
to cooking surface_
21" (49.5 cm)
(53.3 cm) \_
44 5/8" *
(113.3 cm)
Model SGM466
* including embosses/screws in side of chassis
_a_D_ 3
Electrical Requirements Gas SuRply Requirements
WARNING
m
To prevent an electric shock hazard; the power suppJy
must meet the specjficat!ons stated below, it is the own:
er,s responsibility to make sure that the eJectdca_service
meets electrical requirements and that the eJectrica_ outlet
has been properly installed by a _icensed electrician.
The cooktop is supplied with a factory installed,
40-inch, three-prong, grounding electrical plug. It is
connected to the chassis at the bottom right rear corner
(see Chassis Bottom Diagram below). It must be con-
nected to a dedicated, grounded three-prong electrical
e
outlet installed by a licensed electrician.
The electrical installation, including minimum supply
wire size and grounding, must be done in accordance
with National Electric Code ANSI/NFPA 70* and local
codes and ordinances. A copy of this standard may be
obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269-9101
• The correct voltage, frequency and amperage must be
supplied to the electrical outlet according to the product
data label located on the bottom of the chassis. See
the Gas and Electrical Requirements table on this
page for reference.
• Be certain to locate the electrical outlet so that the
power cord may be easily disconnected if the unit
needs service.
Front of unit
Gas inlet
Chassis Bottom Diagram
/
Electric cord
Be certain that the cooktop being installed is correct for
the gas service being provided (natural gas or LP gas).
Also, if operating the cooktop at an altitude above 4000
ft. (1219 m) make sure it is equipped for high altitude
operation.
Units equipped for LP operation have "LP" in the
model number listed on the product data label. See the
Chassis Bottom Diagram for label location.
Units equipped for high altitude operation have an "H"
at the end of the model number listed on the product
data label.
Check your local building codes for the proper method
of installation. In the absence of local codes, this
appliance should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54.
• An external manual shut-off valve must be installed
between the gas inlet and the cooktop for the purpose
of turning on or shutting off gas to the appliance.
The cooktop comes from the factory with a regulator in
the shipping carton. The regulator must be installed in
the gas line that runs from the cooktop gas inlet to the
gas shut off valve. Use only the regulator provided.
• Models SGM304 and SGM365 come with a 1/2" regu-
lator. Model SGM466 comes with a 3/4" regulator,
approved for connection to a 1/2" house gas supply.
The cooktop gas connection is located on the bottom of the
cooktop in the back right corner as you face the front of the
unit. See the Chassis Bottom Diagram on this page.
SGM304 SGM304LP
SGM365 SGM365LP
SGM466 SGM466LP
Gas type Natural gas LP gas
Manifold 4" Water 10" Water
pressure column column
Min. gas supply 5" Water 11" Water
pressure ** column column
Max. gas supply 1/2 p.s.i. 1/2 p.s.i.
pressure
Total connected 0.25 Amp. 0.25 Amp.
load (0.03 kW) (0.03 kW)
Circuit 120 Vac, 120 Vac,
requirement 60 Hz, 15Amp. 60 Hz, 15 Amp.
Gas and Electrical Requirements*
* The electrical and gas data on this page is for reference
only. If the above data does not agree with the product data
label, use the data on the product data label.
** The gas supply pressure for testing the regulator setting
shall be at least 1 inch water column (249 Pa) above the
specified manifold pressure.
4 _SCD_
Cabinet and Countertop Layout
WARNING
• To reduce the risk of personal injury caused by
reaching over a hot appliance, avoid locating cabinet
storage space directly above the cooktop.
• Failure to meet or exceed the maximum and mini-
mum dimensions/clearances stated in these instruc-
tions may result in a fire hazard.
- Follow the countertop manufacturer's instructions
regarding the minimum corner radius, use of heat
reflective tape, reinforcement of corners, etc.
Carefully check the location where the cooktop will be
installed. For best performance, the cooktop should be
placed away from drafts that may be caused by doors,
windows and heating and air conditioning outlets.
This appliance is to be used in conjunction with a suit-
able vent hood or approved Dacor raised vent system.
All tolerances +1/16" (+1.6 mm),-0
unless otherwise noted.
Combustible overhead
cabinets \
13' max7 18"min)' 3
(33.0 cm) (45.7 cm)
Combustible
surface to rear
Allow a minimum 1/4" (6 mm) clearance between the
bottom of the cooktop chassis and all combustible sur-
faces, including the upper edge of a drawer installed
below the cooktop.
Under Cabinet Clearances
Model B: Minimum*
SGM304 29" (73.7 cm)
SGM365 35 1/4" (89.5 cm)
SGM466 46" (116.8 cm)
* To allow clearance for hold down brackets
• The gas supply piping, gas shut-off valve and the elec-
trical outlet must be located so they do not interfere
with the cooktop when it is installed. If installing another
appliance in the cabinet below, allow for the routing of
gas and electrical service behind it.
The installation must allow for the following:
• Access to the gas shut-off valve and regulator when
the unit is installed.
• Access to the electrical outlet when the cooktop is in
place. The 40" (101.6 cm) power cord must be able to
reach the electrical outlet.
• Access to the underside of the cooktop for service and
inspection purposes.
• Clearance inside the cabinet to allow for proper hold
down bracket installation.
See cutout
dimensions
7 1/2" (19.1 cm) min. to
combustible side wall,
above counter both sides
Measured from cooking surface (top of cooktop grate).
2 If installing with an overhead vent hood, also check hood
specifications for minimum required clearances.
3 Not applicable for cabinets more than a horizontal distance of 6"
(15.2 cm) from edge of cooktop. Allow 7 1/2" (19.1 cm) from edge
of cutout.
Minimum Required Clearances Around the Cooktop
To allow access to the utilities and cooktop bottom, a fixed
shelf should not be installed below the cooktop. See the fol=
lowing pages for countertop cutout dimensions.
Raised Vent Compatibility
If installing the cooktop with a raised vent, install only the
approved Dacor model numbers specified below:
Cooktop Models Approved Raised Vent Models
SGM304 ERV30, PRV30 or RV30
SGM365 ERV36, PRV36 or RV36
SGM466 PRV46 or RV46
Model A: Minimum A: Recommended
SGM304 30" (76.2 cm) 36" (91.4 cm)
SGM365 36" (91.4 cm) 42" (106.7 cm)
SGM466 48" (121.9 cm) 54" (137.2 cm)
_a_D_ 5
Cutout Dimensions All tolerances +1/16" (+1.6 mm), -0, unless otherwise noted.
IMPORTANT: Be careful to use the correct cutout diagram (on the facing page) to determine the countertop dimensions
for the installation type. Carefully double check all dimensions against the table below and the correct diagram before cut-
ting the countertop.
Countertop Dimensions
Cutout C
Installation Type Diagram (Minimum) D E F G H
SGM304 without Figure 1 2 7/8" 19 3/4" 27 3/4"
NA NA NA
raised vent (Square) (7.3 cm) (50.2 cm) (68.6 cm)
SGM304 with Figure 1 3/8" 22 1/2" 27 3/4"
NA NA NA
ERV30/PRV30 (Square) (1.0 cm) (57.2 cm)* (68.6 cm)
SGM304 with Figure 1 5/8" 22 1/4" 27 3/4"
NA NA NA
RV30 (Square) (1.6 cm) 56.5 cm)* (68.6 cm)
SGM365 without Figure 1 2 3/8" 19 3/4" 33 5/8"
NA NA NA
raised vent (Square) (6.0 cm) (50.2 cm) (85.4 cm)
SGM365 with Figure 1 3/8" 22 1/2" 33 5/8"
NA NA NA
ERV36/PRV36 (Square) (1.0 cm) (57.2 cm)* (85.4 cm)
SGM365 with Figure 1 5/8" 22 1/4" 33 5/8"
NA NA NA
RV36 (Square) (1.6 cm) (56.5 cm)* (85.4 cm)
SGM466 without Figure 1 2 7/8" 19 3/4" 44 3/4"
NA NA NA
raised vent (Square) (7.3 cm) (50.2 cm) (113.7 cm)
SGM466 with Figure 2 3/8" 22 1/2" 44 3/4" 43 1/2" 5/8" 2 5/8....
PRV46 (Notched) (1.0 cm) (57.2 cm)* (113.7 cm) (110.5 cm) (1.6 cm) (6.7 cm)
SGM466 with Figure 2 5/8" 22 1/4" 44 3/4" 43 1/2" 5/8" 2 3/8....
RV46 (Notched) (1.6 cm) (56.5 cm)* (113.7 cm) (110.5 cm) (1.6 cm) (6.0 cm)
Total cutout depth, accommodates both the cooktop and raised vent
** IMPORTANT: Notch depth is included in total cutout depth (D). DO NOT add notch depth to total cutout depth (D).
Stiffener
3/8" min. (1.0 cm)
flat countertop overhang
required behind cutout Countertop
SGM series cooktop
I I
Cabinet face _-,
I I
I I
- 3/8" min. (1.0 cm) space ,",
/J/ I I
z behind raised vent ,,
I I
chassis to clear stiffener ,'
I I
I I
I I
,z ERV or PRV series raised ,,
I I
- I vent: Check raised vent ,",
dimensions/specifications ,",
I I
to determine proper fit ,,
I I
I I
I I
I I
I I
I I
-- I I
ii
ii
Floor ,,
Side View - SGM Series Cooktop with
ERV or PRV Series Raised Vent
Stiffener
5/8"min. (1.6cm)
flat countertop overhang
. required behindcutout Countertop
I I
• I I
SGM series cooktop ,,
1 IL Cabinet face _
• I I
I I
I 5/8"m,n.(1.Gcm/space ,,
I I
1_ II behind raised vent ,,
I I
I IIchassis to clear stiffener ,,
• • I I
I J_ RV series raised vent: ,,
• I I
I II Check raised vent ,,
..... I I
I I
I II dimensions/specifications ,,
I II "
to determine proper fit ',,
-_1 i_p4 5/8"(11.7cm) i i
m i
I III 9 7/8" (25.1 cm) with ,,
I I
h---t I CABP3 blower installed ,,
...... J-.L ......................... J_
T_ - - ,,a
II
II
Floor ,,
Side View - SGM Series Cooktop with
RV Series Raised Vent
6 _SCD_
Rear
wall
Vertical
combustible
surface
4 1/4" (10.8 cm) min.
from mounting surface to
combustibles below
cooktop chassis
7 1/2" (19.1 cm) min.
to combustible
side wall above
countertop
(both sides)
1 7/8" min.
(4.8 cm)
Figure 1 =Square Countertop Cutout Diagram
t
Rear
wall
4 1/4" (10.8 cm) min. from
mounting surface to combustibles
below cooktop chassis
Vertical
combustible
surface
7 1/2" (19.1 cm) min.
to combustible
side wall above
countertop
(both sides)
1 7/8" min.
(4.8 cm)
Figure 2 = Notched Countertop Cutout Diagram
_a_D_ 7
Verify Package Contents Connecting the Gas Line
• Hold down brackets (2)
• Gas pressure regulator
• Grates (2 for SGM304, 3 for SGM365 and SGM466)
• Burner sets (4 for SGM304, 5 for SGM365, 6 for
SGM466)
• Stainless steel cleaner (stainless steel models only)
If any parts are missing, see the Parts List section on
page 11 for ordering information.
Installing the Cooktop
WARNING
verifythatthepowersupplymeetsthespec!f Gati0ns
on page 4 before proCeedingl
• To prevent damage to the gas pressure regulator,
!nstatl !t only after the c00kteP iS mounted in its per:
manent position. ................
IMPORTANT
Do not 0VeFtightenthe h01ddown b01tS,over tighb
ening the hold down bolts may result in improper
operation of the dual gas burners,
' a 0 not use a hardening CompoUnd 0r caulk to perma_
neatly seal the cooktop into place: The cooktop must
be readily remOVable ifService is required! RemOval
of sealan! to service the unit will be performed at the
cUst0mer S expensel
1. If the cooktop will be used with a raised vent, install the
vent according to it's installation instructions first.
2. Lower the cooktop into the cutout and center it.
3. Secure the cooktop to the countertop using the two (2)
provided hold-down brackets as shown.
_, (both sides)
Gas inlet _
/
/
Electriccord
Hold Down
Bracket Installation
WARNING
- Verify that the gas supply meets specifications before
connection. See page 4.
- Do not install or use the cooktop without the included
gas regulator installed.
- Ensure that the arrow on the regulator points in the
direction of the gas flow, towards the cooktop.
- Do not apply excessive pressure when tightening gas
connections and fittings.
- Do not use Teflon tape or plumber's putty on flexible
gas line connections.
- Test the gas lines for leaks as instructed before use.
Do not use a flame to check for leaks.
- The maximum gas supply pressure to the regulator
must never exceed 1/2 pounds per square inch (psi)
or 3.5 kPa.
- The cooktop and shut-off valve must be disconnected
from the gas supply piping system during any pres-
sure testing exceeding 1/2 psi (3.5 kPa).
- The cooktop must be isolated from the gas supply
piping system by closing the shut-off valve to the
cooktop during any gas supply piping system pres-
sure testing equal to or less than 1/2 psi (3.5 kPa).
o For LP gas installations, the LP gas tank must have
its own high-pressure regulator in addition to the
pressure regulator supplied with the cooktop.
,
Attach the gas pressure regulator (included with the
cooktop) to the cooktop pipe nipple inlet. For tight
installations, the regulator may be installed upstream
from the pipe nipple, anywhere between the shut-off
valve and the cooktop. For best performance, minimize
gas pressure loss by attaching the regulator as close
as possible to the cooktop gas inlet.
Complete connection of the gas supply to the cooktop
by installing a minimum 1/2" flexible gas line (not
included) between the pressure regulator and the shut-
off valve.
3. Check for gas leaks:
0
0
Turn all cooktop control valves to the OFF position.
Turn on the gas supply valve and check all lines
and connections for leaks using a soap and water
solution or a gas leak detector.
0 Turn the gas supply off.
8 _8CO_
Installing the Burner Components Veri. Proper Operation
WARNING
Never attempt tO operate the cooktop with anyof the
burner parts removed
, Do not attempt to adjust the burner air mixture set-
tingsl All adjustments are preset at the factory,
,
,
,
Remove the burner heads, burner rings, burner caps
and grates from their shipping packages.
Install the burners as shown. When installing the burn-
er components, twist each piece back and forth slightly
until it drops completely into place. The burners will
not operate properly unless all of the burner pieces are
properly seated.
Gently set the grates on top of the spill tray. Make sure
that the rubber feet are positioned in the dimples.
Grate
z Burner cap
J
_Burner ring
J
/-
jTop frame
"_ Burner head
(fixed)
Cooktop Burner Components
Tabs
5 places
__i_Ni ; 5 ptl:hc:s
i i
WARNING
' sure that Power to the electrical out et is turned
at the Circuit breaker panel or fuse box and that
the gasis turned off atthe gas supply Valve before
proceedingl
; The €00ktop must be pr0perly gr0unded at ali times
when electrical power is applied:
Prior to operating the cooktop, read the accompanying use
and care manual carefully.
,
,
3.
,
,
6.
Make sure all the cooktop burner controls are in the
OFF position.
Connect the power cord to the electrical outlet.
Turn on power to the electrical outlet at the circuit
breaker or fuse box.
Depress and turn one burner control knob at a time
slowly- counterclockwise to the HIGH position. Verify
that the associated burner igniter sparks, then return
the knob to the OFF position. Repeat for all of the
remaining control knobs.
Turn on the gas supply valve.
Perform the following ignition test for all of the burners:
Press and turn the control knob slowly_counter-
clockwise to the HIGH position. Only the selected
burner will spark. It may take up to four seconds
for the burner to ignite, at which time the igniter
will stop sparking. If ignition does not occur within
four seconds, turn off the knob, wait for at least five
minutes to allow any gas to dissipate, then repeat
the test.
Knob
Low
position
Off position
Knob position
indicator
(polished surface)
Burner
designation
Area of
operation
Light and high
position
Burner Control Knob
Burner Ring Installation Detail Continued...
_a_D_ 9
Verifivj Proper Operation (Cont)_
• Once the burner lights, rotate the control knob
counterclockwise from HIGH to LOW to adjust the
flame height progressively.
When the unit is installed properly, the flame will
be steady. It will also have a sharp, blue inner cone
that will vary in length proportional to the burner
size. The flame will be reduced by the Smart
Flame TM feature under the grate fingers to increase
grate life.
Installation Checklist
WARNING
To ensure a safe and pr0Per installation, the following
checklist should be completed by the installer to ensure
that no part of the installation has been overlooked:
Pr0per installation is the resp0nsibilitY of the homeowner:
The importance of proper installation of your Dac0r
cooktop cannot be overemphasized:
[]
Is the electrical outlet for the cooktop grounded and
located according to these instructions and in accor-
dance with all applicable electrical codes? See page
4.
Normal Flame Appearance
NOTE: If the cooktop does not operate properly, follow
these troubleshooting steps:
• Verify that power and gas are supplied to the cooktop.
• Check to make sure that the power plug is connected
to the electrical outlet and that power is turned on at
the circuit breaker or fuse box.
• Check to make sure that the burners are properly
seated.
• If the burner continues to spark after ignition without
stopping, have a licensed electrician check the electri-
cal outlet for proper grounding or reversed polarity.
• Repeat the above burner ignition test.
• If the appliance still does not work, contact Dacor
Distinctive Service at (877) 337-3226. Do not attempt
to repair the appliance yourself. If you need service, be
sure to have the model and serial numbers available
when you call. See inside cover for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
[]
[]
[]
[]
[]
[]
[]
Is the gas service for the cooktop located and installed
according to these instructions and in accordance with
all applicable codes? See page 4.
Has the gas supply inlet pressure been measured to
ensure that it does not exceed the maximums stated in
these instructions? See page 4.
Is the cooktop secured using the provided hold-down
brackets? See page 8.
Is the cooktop connected to the gas supply according
to these instructions and in accordance with all appli-
cable codes? Did the installer check the gas supply for
leaks? See page 8.
Are the burners and grates properly installed according
to these instructions? See page 9.
Has proper operation been verified?
Has the warranty been activated on-line or the warranty
card filled out completely and mailed?
10 da=or
Parts List SGM466
Replacement parts may be obtained by contacting Dacor
Customer Service.
Dacor Customer Service
Phone: (800) 793-0093 (U.S.A. and Canada)
Monday -- Friday 6:00 A.M. to 5:00 P.M.Pacific Time
Parts Used on All Models
Dacor Part
Description Number
Hold down bracket w/screws
12269
(2 sets)
Stainless steel cleaner A302
(stainless steel models only)
SGM304
Dacor Part
Description Number
Regulator 82540
Grate 82925SB
Burner cap - left front 72435BM
Burner ring - left front 86918
Burner cap - left rear, right front 86524BM
Burner ring - left rear, right front 86408
Burner cap - right rear 86523BM
Burner ring - right rear 86407
SGM365
Dacor Part
Description Number
Regulator 82540
Grate- large 82925SB
Grate - small 62443SB
Burner cap - left front 72435BM
Burner ring - left front 86918
Burner cap - left rear, right front 86524BM
Burner ring - left rear, right front 86408
Burner cap - center rear, right rear 86523BM
Burner ring - center rear, right rear 86407
Dacor Part
Description Number
Regulator (natural gas) 62320
Regulator (LP) 62434
Grate 82926SB
Burner cap - left front, right front 72435SB
Burner ring - left front, right front 86918
Burner cap - left rear, center front, right rear 86524SB
Burner ring - left rear, center front, right rear 86408
Burner cap - center rear 86523SB
Burner ring - center rear 86407
da=Dr, 11
BLK
120V,60Hz
PI]WERSUPPLY
AFTER SERVICING
VERIFYPRI]PERI]PERATInN
N
84
$3
$8
$1
WIRINGDIAGRAM
SGM304
CAUTIDNuLABELALLVIRESPRI{]RTI]DISCDNNECTIDN
VHENSERVICINGCBNTRBLS,VIRINGERRDRSCAN
CAUSEIMPRBPERAND DANGERDUSBPERATIBN.
m
G
N
A
4 RE-IGNITDR
4 PDINT
3
8
1
IGNITDRa
HT
$4
$3
$8
s1
IGNITDRI
VHT
IGNITDR4
HT
_ IGNITDR3
VHT
12 dater
L
120V,60Hz
PFIWERSUPPLY
AFTER SERVICING
VERIFYPR[IPER[IPERATIDN
I-
i
--i GND
!N
iA
15
i4
i
-----i 3
---I a
i
-il
i
WIRINGDIAGRAM
SGM365
CAUTIDNILABELALLVIRESPRInRTDDISCDNNECTIrIN
VHENSERVICINGCDNTRDLS,VIRINGERRDRSCAN
CAUSEIMPRDPERAND DANGERDUSDPERATIDN,
N
LIGHT
©
RE-IGNITnR
5 PDINT
IGNITDR,
LRBURNER
IGNITnR,
LF BURNER
m
55
54
53
52
51
IGNITnR,
CENTER
IGNITnR,
RR BURNER
IGNITDR,
RF BURNER
m
dacDn 13
3LK
120V,60Hz
P[lWERSUPPLY
AFTER SERVICING
VERIFY PRI]PERI]PERATII]N
b,,I,I,,,--
-0/0
% I
$5
_o..---Jo__
S4
-o-'Jo-
$3
_o.-Jo
52
__o..---Jo-
51
N
'VHT
I_
]
m
GND
N
6
5
4 RE-IGNITnR
6 PDINT
3
2
i
VIRINGDIAGRAM
SGM466
CAUTmN,LABELALLWIRESPRInRTnDISCnNNECTmN
WHENSERVICINGCnNTRnLS,WIRINGERRI]RSCAN
CAUSEIMPRDPERANDDANGERI]USDPERATII]N,
IGNITnRLR
HT
IGNITnRMR
HT
IGNITnRRR
HT
56
55
54
53
52
51
_ IGNITnRLF
VHT
_ IGNITBRMF
VHT
IGNITDRRF
VHT
14 da=_r
dacDr 15
16 da=_r
Family Owned
American Made
Dacor = 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 = Phone: (800) 793-0093 = Fax: (626)403-3130 = www.Dacor.com
The Life of the Kitchen?
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Dacor SGM466B Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Dacor ERV48ER Combined Configuration Drop-In Electric Cooktop - Slim Raised Vent?? PDF [0.5 MB]
-
-
-
Dacor ERV3615 User guide
-
Dacor ERV48-ER Owner's manual
-
-
-
-
Dacor CABP3 Planning Guides PDF [0.5 MB]
-
Other documents
-
KitchenAid KGCC566RBL Dimensions Guide
-
KitchenAid KGCC506RWW User guide
-
GE HCC2230AGS Installation guide
-
Warehouse of Tiffany RL79446 Installation guide
-
KitchenAid KGCS105G User manual
-
-
Sears SGM466 User manual
-
-
-