Stinger SPXRNGDASH Owner's manual

Brand: Stinger

Model: SPXRNGDASH

Type: Owner's manual

SPXRNGDASH

Installation Guide

3” Aftermarket Multimedia Dash Kit

for select 2013–2018 Polaris Ranger

 Flat Blade Screwdriver

 Torx T25

 Air Saw or similar to cut plastic

 Philips Screwdriver

 Ruler

 Marker / Masking Tape

Recommended Tools

Vehicle Fitment

Parts List

Item Description

Q Qty

1 Main Frame 1

2 Top Cover 1

3 #8 X 3/8” Screw 2

4 #8 X 1 1/4” Screw 4

5 Locking Hook 4

RANGER 1000 XP 2017

RANGER CREW 900 2014-2017

RANGER CREW 900 XP 2018

RANGER CREW 1000 XP 2017-2018

RANGER DIESEL HST 2014

RANGER HST 2015-2017

BRUTUS HD 2013-2018

RANGER 570 FULL SIZE 2015-2016

RANGER 570, 570 XP 2016

RANGER 570 EFI FULL SIZE CREW 2015

RANGER 900 EPS 2017-2018

RANGER 900 XP 2013-2017

RANGER 1000 DIESEL 2015-2018

3 4

Remove top dash cover by removing

the 4 clips with a at blade screwdriver.

From inside the vehicle, place shift lever in low-

est gear and then pull dash cover towards you

to release.

Two modicatrions need to be made to the factory center dash bezel to allow an aftermarket radio to be

installed. The back portion of the top pocket will need to be removed and a notch will need to be cut into the

top of the pocket.

Remove the (2) Torx T25 screws from the

bottom of the center dash bezel. Unplug all

electrical connections and remove.

T25

There are “ribs” on all four sides of the

pocket. Using the ribs closest to the bezel as

a guide, mark a cut line as shown below in

RED.

Following the cut line, cut around the

pocket with your favorite cutting tool and

remove back portion of the pocket.

6 7

Centered on the top edge of the bezel, mark a 3” rectangle that is 1/2”from the bend line.

Cut out notch, cutting through both the top edge of the bezel and the top of the pocket.

Using (2) #8 x 3/8” screws, attach the Top Cover

to the Main Frame. Insert the complete assembly

into the front of pocket.

Using the (4) Locking Hooks and #8 x 1 1/4”

screws, attach the Main Frame assembly to

the factory dash bezel.

3”

1/2”

CENTER LINE

8 9

Mount the radio to SPXRNGDASH using the har-

ware supplied from the radio manufaturer.

After making all neccessary wire connections,

reinstall the center dash assembly into the vehi-

cle.

LIMITED WARRANTY:

Stinger warrants this product to be free of defects in materials and workmanship for

a period of one (1) years from the original date of purchase. This warranty is not

transferable and applies only to the original purchaser from an authorized Stinger

dealer in the United States of America only. Should service be necessary under this

warranty for any reason due to manufacturing defect or malfunction, Stinger will (at

its discretion), repair or replace the defective product with new or remanufactured

product at no charge. Damage caused by the following is not covered under

warranty: accident, misuse, abuse, product modication or neglect, failure to follow

installation instructions, unauthorized repair attempts, misrepresentations by the

seller. This warranty does not cover incidental or consequential damages and does

not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to

accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES:

Products purchased outside the United States of America are covered only by that

country’s Authorized Stinger reseller and not by Stinger. Consumers needing service

or warranty information for these products must contact that country’s reseller for

information.

Stinger is a Power Brand of AAMP Global

15500 Lightwave, Clearwater, Florida 33760

P: 888-228-5560

[email protected]

www.stingerelectronics.com

TECHNICAL SUPPORT:

727-592-5991

Mon-Fri 9AM-8PM EST

Sat 9AM-7PM EST

[email protected]

Stinger SPXRNGDASH Owner's manual

Stinger SPXRNGDASH Owner's manual

Stinger SPXRNGDASH Owner's manual

Related papers

Other documents