1
REV 0 - 1709011350
L-C2-444
Model# 24-IL-C
30-IL-C
36-IL-C
Grill Series Liner Model
24NBL, 24NBT
24-IL-C
30NBL, 30NBT 30-IL-C
36NBL, 36NBT 36-IL-C
Table 1 - Models available
SPECIFICATIONS
Fig. 1-1 Installation orientation
Cut-out
GRILL INSULATING LINER
IMPORTANT INFORMATION
Read these instructions and the safety and installation sections
of the grill owner's manual before liner installation.
The insulating liner comes pre-assembled and ready to install.
FOR YOUR SAFETY, the enclosure must provide openings for
drainage, replacement air, and cross-ventilation of any storage
area exposed to possible leakage from gas connections, the
unit, or propane cylinders.
This liner is only for installation in an enclosure constructed
of combustible materials and a NON-COMBUSTIBLE
countertop.
All additional enclosure requirements, safety guidelines,
and any other requirements found in your grill owner's
manual MUST BE FOLLOWED.
The insulating liner is designed to be supported from the
countertop using the liner hangers. S
ee Fig. 1-1.
Note: Framing the cut-out with side walls, a rear wall, and a
base is permitted.
See your grill owner's manual for all overall enclosure
requirements.
See sections on following pages regarding cutout
dimensions, and countertop overhang and substrate
considerations. Then proceed to INSTALLATION.
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
Support
using liner
hangers
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
2
REV 0 - 1709011350
L-C2-444
Grill series
24NBL,
24NBT
30NBL,
30NBT
36NBL,
36NBT
Insulating liner model 24-IL-C 30-IL-C 36-IL-C
A Countertop to unit bottom cut-out 9" 9" 9"
B Side to side cut-out 28
5
/
8
" 34
5
/
8
" 40
5
/
8
"
C Front to back cut-out * 21
5
/
8
" 21
5
/
8
" 21
5
/
8
"
D Liner fl ange width cut-out
†
29
5
/
8
" 35
5
/
8
" 41
5
/
8
"
*
Includes any substrate at front wall of enclosure (in the areas the liner fl anges are to sit fl ush against).
See SUBSTRATE section on next page.
†
Only applicable for enclosures that have countertops with an overhang (see illustration and section below).
Table 2 - Cutout Dimensions
SPECIFICATIONS (cont.)
CUTOUT DIMENSIONS
TOP VIEW
Non-combustible
Countertop
Countertop
overhang
CUT-OUT
DIMENSIONS
Fig. 2-1
FRONT VIEW
B
C
D
Countertop
overhang
X
TOP VIEW
(Countertop)
Y
(Overhang)
A
Drawings
not to scale
(Liner
fl ange)
(Liner shown
for clarity)
See next page
for substrate
considerations
X= D-B
÷
2
Y= Total
Countertop
Overhang
COUNTERTOP OVERHANG
The liner front fl anges are designed to sit fl ush against the grill enclosure front wall. If the countertop extends
beyond the front wall, creating a countertop overhang, it must be cut fl ush with the front wall for the width of
the liner fl anges or a gap will be created exposing the forward portions of the left and right side liner walls. See
illustrations above.
ENCLOSURE VENTILATION
FOR YOUR SAFETY, you must provide openings in the grill enclosure for replacement air and cross-ventilation
(in case of possible leakage from gas connections or propane cylinders). Failure to do so may result in a fi re
or explosion causing property damage, bodily injury, or death. See the GRILL ENCLOSURE/VENTILATION
REQUIREMENTS section in the grill owner's manual for details.
3
REV 0 - 1709011350
L-C2-444
1
1
/2"
hole
(gas)
Fig. 3-3 Install insulating liner
1
1
/2"
electrical hole
(if applicable)
Fig. 3-4 Install grill into liner
Grill hanger
rests on
insulating liner
(sides and rear)
SPECIFICATIONS (cont.)
INSTALLATION
1. Install the insulating liner as shown in Fig. 3-3.
• If installing on a countertop with an irregular/textured
surface, a bead of silicone sealer rated for 400° or higher
may be needed to protect from the elements.
• The insulating liner has knock-out holes (two at the front,
and two at the rear) for electrical feeds (if applicable), and
the gas feed.
Note: If possible, use the front hole for electrical feeds. See
Fig. 3-3.
2. Install your grill per your grill owner's manual.
Important: Do not allow the grill hanger to come in contact
with the countertop or any combustible surface
(
see Fig. 3-4).
Substrate
When adding any substrate to the enclosure front wall (including tiles, stone, etc.), make allowance for:
Substrate Behind Liner Flange
Substrate Alongside Liner Flange
C
C
Flush
(Countertop)
(Countertop)
Liner fl ange
(both sides)
Substrate
(includes tiles,
etc. at front of
enclosure)
Countertop
overhang
(if applicable)
Liner
Liner
Substrate
(includes tiles,
etc. at front of
enclosure)
Any additional substrate alongside the liner fl anges does
not need to be considered in Dim. C (see previous page).
Substrate
+
countertop "front to back" cutout
must equate to Dim. C (see previous page)
when the substrate sits fl ush behind the
liner fl anges.
Fig. 3-1 Fig. 3-2
Countertop
overhang
(if applicable)
TOP VIEW
TOP VIEW
Flush
Liner fl ange
(both sides)
4
REV 0 - 1709011350
L-C2-444
NOTES PAGE
Please use this page to record any information that you may want to have at hand.
-
1
-
2
-
3
-
4
American Outdoor Grill 36ILC User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Fire Magic Grill Insulating Liner User manual
-
-
-
-
Fire Magic Echelon Analog Built-in Grill User manual
-
-
-
-
-