GE ZGU364LDP6SS Installation guide

Installation

Instructions

36" and 48"

Professional Rangetops

Tables de cuisson

professionnelles de 36" (91 cm)

et de 48" 1122 cml

Instructions d'installation

Lo section fran_oise commence 6 Io page 25

Estufas profesionales

de 36" (91 cm)y 48" (122 cm)

Instrucciones de instalaci6n

Lo secci6n en espafiol empieza en Io p6gino 28

131-i0S141

06-i0 GE

Safety Information

BEFORE YOU BEGIN

Reod these instructions completely ond corefully.

"IMPORTANT- Savetheseinstructionsfor

local inspector's use.

"IMPORTANT-Observeallgoverning

codes and ordinances.

, Note to Installer- Be sure to leave these

instructions with the Consumer.

, Note to Consumer - Keep these instructions

with your Owner's Manual for future reference.

, Completion Time- 1to 3 hours.

, Proper installation is the responsibility of

the installer. Product failure due to improper

installation is not covered under the warranty. See

Owner's Manual for warranty information.

AWARNING

This appliance must be properly grounded. Follow

directions in "ElectricSupply"of this manual. Failureto do so

may result in electric shock.

For Monogram local service in your area,

1.800.444.1845.

For Monogram Service in Canada, call

1.800.561.5544.

For Monogram Parts and Accessories, call

1.800.626.2002.

If you received a damaged rangetop, you should

contact your dealer.

In the Commonwealth of Massachusetts:

, This product must be installed by a licensed

plumber or gas fitter.

, When using ball type gas shut off valves, they

shall be T-handle type.

, A flexible gas connector, when used, must not

exceed 3 feet.

Vent hood Combinations:

It is recommended that these rangetops be installed

in conjunction with a suitable overhead vent hood.

, Install a hood with at least 1200 CFM above a 48"

wide rangetop.

, Install a hood with at least 600 CFM above a 56"

rangetop.

Due to the high heat capacity of this unit, particular

attention should be paid to the hood and ductwork

installation to assure it meets local building codes,

AWARNING:

Clearancesto horizontalsurfacesabove the range,

measured to the cooking surface are below. Failureto

comply may result infire hazard.

, Installations without a hood require 48" minimum

to combustibles.

, A custom hood installation with exposed

horizontal combustibles surfaces must hove

an Auto-On feature.

, For other installations with a hood, refer to hood

installation instructions for specific hood

clearances.

ACAUTION:

These rangetops are extremely heavy. Due to the

weight and size of the rangetop and to reduce the

risk of personal injury or damage to the product:

TWO PEOPLEARE REQUIRED FOR PROPER

INSTALLATION.

Installation must conform with local codes. In the

absence of local codes, the rangetop must comply

with the National Fuel Gas Code, ANSIZ225.1/

NFPA 54, latest edition and National Electrical Code

ANSI/NFPA 70 latest addition. In Canada, installation

must conform with the current Natural Gas

Installation Code, CAN/CGA-B149.Z or the current

Propane Installation Code, CAN/CGA-B149.2, and

with local codes where applicable. This rangetop has

been design-certified by CSA International according

to ANSI Z21.1, latest edition and Canadian Gas

Association according to CAN/CGA-Z.1 latest edition.

Leak testing of the appliance shall be conducted

according to the manufacturer's instructions.

Design Information

CONTENTS

Design Information

Models Available ......................................................................3

Backsplash Accessories .......................................................3

Product Dimensions and Clearances

for 48" Wide Models ...............................................................4

Product Dimensions and Clearances

for 36" Wide Models ...............................................................5

Installation Options ...............................................................6

Installation Preparation

Tools and Materials Required ...........................................7

Power Supply Locations .....................................................7

Remove Packaging .................................................................8

Installation Instructions

Step 1, Cut the Countertop Opening ..............................9

Step 2, Install the Rungetop ............................................10

Step 3, Connect Rungetop to Gas ................................10

Step 4, Connect Electrical .................................................11

Step 5, Check Burners .......................................................11

Finalize Installation ..............................................................11

Installation Checklist ...........................................................11

Install the Rangetop Backsplash Accessory ............12

Install the Adjustable

Bocksplosh Accessory ................................................13, 14

MODELS AVAILABLE

Monogram rangetops are factorysetfornatural

gas.Order the model foryour installationsituation.

48" Natural Gas Models:

ZGU484NG - 4 gas burners, grill and griddle

ZGU486NR- 6 gas burners and grill

ZGU486ND - 6 gas burners and griddle

36" Natural Gas Models:

ZGU364ND - 4 gas burners and griddle

ZGU364NR- 4 gas burners and grill

ZGU366N - 6 gas burners

BACKSPLASH ACCESSORIES

All models require 12" minimum clearance

to a vertical combustible surface at the rear.

If clearance is less than 12", the entire surface

of the back wall above the countertop and the

full width of the rangetop must be protected by a

backsplash. The backsplash must be constructed

of non-combustible material, such as metal, ceramic

tile, brick, marble or other stone.

Two Backsplash Accessories Available:

• The 12" high stainless steel backsplash accessory

is available. Use this backsplash in combination

with a custom, non-combustible backsplush built

beyond the 12" height. The combined height

of the bucksplush accessory and the custom

backsplash must reach the bottom of u hood,

or when there is no hood, to 48" above

the cooking surface.

• An adjustable 30" to 36" high backsplash with shelf

is also available. This backsplash fills in the space

between the top of the rangetop and the bottom

of the hood. The shelf is positioned so that

heat lamps from the bottom of a Monogram

professional hood are directed towards the shelf.

12" High Backsplash

ZX12B48PSS,for 48" wide rangetops

ZX12BB6PSS,for 56" wide rangetops

30"to 36" Adjustable Height

Backsplash With Shelf

ZXADJB/48PSS,for 48" wide

rangetops

ZXADJB36PSS,for 36" wide

rangetops

Design Information

PRODUCT DIMENSIONS AND CLEARANCES FOR 48" MODELS

.._ 27-1/2" to

47-7/8" Width _ _ Front of

.................__ _u,,nose

-_/2"

Height

Locate gas

inlet on back

wall or on

floor 2"from

back wall.

Universal Utility Locations

AWARNING:

Installations without a hood

require 48" minimum to combustibles

above the rangetop. A custom hood

installation with exposed horizontal

combustible surfaces must have

an Auto-On feature. Refer to hood

installation instructions for specific

hood clearances.

The surface of the entire back wall

above the countertop and below

the hood must be covered with

a non-combustible material such

as metal, ceramic tile, brick, marble

or other stone.

13"

Min.

48" Minimum

to Combustibles

46-1/4"

22-3/4" Min.

\

12" Minimum

-- EachSide

12" Minimum to

Adjacent Wall

7/8"

* The opening between a 4" high backsplash must be 48"

to allow the rangetop to slide back against the wall.

ADDITIONAL CLEARANCES:

Allow 12" minimum clearance to an adjacent wall on

each side.

Working areas adJacent to the rangetop should have

18" minimum clearance between countertop and the

bottom of the wall cabinet.

12"Minimum to

Combustibles or 0"to

non-combustible

material above the

cooking surface

48" Min. to

Combustibles

o

--Clearanc

Design Information

PRODUCT DIMENSIONS AND CLEARANCES FOR 36" MODELS

,,d 27-1/2" to

35-7/8" Width ..............L _ Front of

......................... _--_ "- aullnose

.,......... . €

8-1/2"

Height

Locate gas

inlet on back

wall or on

floor 2"from

back wall.

Universal Utility Locations

AWARNING:

Installations without a hood

require 48" minimum to combustibles

above the rangetop. A custom hood

installation with exposed horizontal

combustible surfaces must have

an Auto-On feature. Referto hood

installation instructions for specific

hood clearances.

The surface of the entire back wall

above the countertop and below

the hood must be covered with

a non-combustible material such

as metal, ceramic tile, brick, marble

or other stone.

13" Max.

18" Min.

l

48" Minimum

to Combustibles

F

combustible 12"Minimum

' EachSide

35"

22-3/4" Min.

36"

O

12" Minimum to

Adjacent Wall

1/2"

2-1/2"

* The opening between a 4" high backsplash must be 36"

to allow the rangetop to slide back against the wall.

ADDITIONAL CLEARANCES:

Allow 12" minimum clearance to an adjacent wall on

each side.

Working areas adJacent to the rangetop should have

18" minimum clearance between countertop and the

bottom of the wall cabinet.

12"Minimum to

Combustibles or 0" to

non-combustible

material above the

cooking surface 48" Min. to

Combustibles

0" -I

Clearanc

5

Design Information

INSTALLATION OPTIONS

8"

Countertop 8-1/2"

Level Height

Backedge

of chamfer

* Minimum cabinet cutout depth from

the back of the rear trim to the back

finished edge of the control panel -

typically, the minimum cabinet depth

(front to back). Maximum cabinet cutout

depth is 26" minus the countertop

overhang.

-,I.....................................................................................................................................28-13/18" ..................................................................................... _,-

ToFront ofControl Knobs

27-1/2" ........................................................................................................................................

ToFrontof Bullnose

\

Finished back edge

of control panel

/

\ ! 'J I

8-1/2"_:: _D,-

5-1/4" '_

7-1/4"

23-1/2 _,-

** 26" .........................................................D,.

1/2"

Countertop

Level.........

_, t3/32"

.......1-3/16"

1-1/32"

ToPipeStub

Center

26-3/4" .................................................................................................................................................

TOFront of Control Panel

t Includethe overhung ofthe rear trim when countertop continuesbehindthe product.

Theoverhung isdecorativeonly.Theweight of therungetop isfully supported bythesidetrims.

** Maximum countertop cutout depth

from the buck of the rear trim

to the buck edge of chamfer at the

sides of the control panel - typically,

the maximum countertop cutout depth

ffront to buck). Minimum countertop

cutout depth is25-1/4".

Rangetop

1/2" Above Adjacent

Countertops

Rangetop

1/2" Above Adjacent

Countertops

Control panel projects forwards from

standard depth cabinets.

Front of deep cabinets can align with control

panel beveled edge.

Installation Preparation

TOOLS REQUIRED

Saber Saw

Measuring Tape

Carpenter's Square

Safety Glasses

Phillips #2

Screwdriver

Level

Drill and

Appropriate Bits

Adjustable Wrench

1/4" Driver or

Wrench

Hand Truck

MATERIALS PROVIDED

Hold-Down Regulator

Strap

MATERIALS REQUIRED (not provided}

Joint Pipe Fittings Shut-Off

Sealant Valve

5-foot maximum length, 5/8" O.D. CSA-approved

flexible metal gas supply

(3-foot maximum length in Massachusetts only)

NOTE: Purchase new flexible line; do not use

previously used flexible gas line.

POWER SUPPLY LOCATIONS

Gas Supply:

• The natural gas models are designed to operate at 5"

water column pressure. For proper operation, the

pressure of the natural gas supplied to the regulator

must be between 7" and 13" water column.

• Locate the pipe stub on the back wall or floor

(see"Product Dimensions and Clearances"). Use S-foot

maximum length, 5/8" O.D.flexible gas supply line

(3-foot in Massachusetts).

• Install a manual shut-off valve in the gas line

(not provided), in an easily accessible location. Make sure

the homeowner knows where and how to shut off the gas

supply to the rangetop.

Electric Supply:

These rangetops must be supplied with 120 volt, 60 Hz.,

and connected to a dedicated, properly grounded branch

circuit protected by a 15 amp circuit breaker or time

delay fuse.

The power cord of this appliance isequipped with a

three-prong (grounding) plug which mates with a standard

three-prong grounding wall receptacle to minimize the

possibility of shock hazard from this appliance.

If the electrical service provided does not meet the above

specifications, it is recommended that a licensed electrician

install an approved outlet.

DO NOT,UNDERANY

CIRCUMSTANCES,CUT

ORREMOVETHETHIRD

(GROUND)PRONGFROiVl

THE POWERCORD.

DO NOTUSEAN EXTENSION

CORDWITH THISAPPLIANCE.

• Locate the electric supply

within the area shown or

ReceptacleBoxCoverPlate....

ThreeProngPlug

"\

__ihr Pr n R t

within reach of the rangetop's four-foot power cord.

•To avoid tangling cord with items stored in the cabinet,

locate the receptacle on rear wall, inside the cabinet.

Installation Preparation

REMOVE PACKAGING

ACAUTION

Stand dear. The ends of the cut metaJ banding may

snap toward you.

,Cut the metal banding.

,Remove packaging tape and foam.

Dispose of packaging materials properly.

,Remove grill/griddle covers, grill grate and burner

grates.

,Lift out cast-iron griddle flue cover, grease

troughs and pads.

,Cut the ties holding the grill grate to the grill frame.

Griddle Flue Cover

Ties Grease Troughs

, Lift off burner caps and remove foam pad,

then lift off burner heads and remove foam pad.

Remove Foam Pads ......

Installation

STEP 1

Allow Additional

ClearanceBelow

the RangetopBurner

Boxfor the Regulator

andGasConnections

CUT THE COUNTERTOP OPENING

Avalable, .} 30"

asn ............ ,, to36"

BackSpl 12 I

Allow Additional

ClearanceBelow

the RangetopBurner

Boxfor the Regulator

andGasConnections

48" wide models are designed to fit in 48" or wider base cabinets

Measure carefully when cutting the countertop.

Make sure sides of the opening are parallel.

• Allow 8" free space below the top surface of the countertop.

• Allow additional clearances below the burner box

to install the regulator and make house supply

connections. Use a 90° elbow to route the gas

connections and limit interference with drawers

or other cabinetry features.

•These rangetops are designed to hang from

the countertop by their side flanges.

• Smooth any rough edges on the countertop before

installing the rangetop.

- Formica countertop edges must be finished.

The countertop must be strong enough to support

the weight of the rangetop.

56"widemodelsare designedto fit in 56"or wider basecabinets

Cutout Opening with False Bottom

Dimensions

A (Oia.) B C O

56"Rangeto 7-3/8" 1-1/2" 7-1/2" ii-i/8"

48"Rangeto 8-1/4" 1-1/2" 7-1/2" 11-1/8"

• You can construct the cutout with afalse bottom to

conceal the bottom of the rangetop.

- Build the false bottom using a solid material; cut a

7-1/2" x 11-1/8" hole in the left rear corner for the gas

inlet and power cord clearances.

Installation

STEP 2 INSTALL RANGETOP

,Slide the rangetop into the opening. Make sure

the rangetop is evenly seated and supported.

,A hold-down strap with screws is provided to

secure the rangetop to the rear or side cabinet

walls.

, Remove the hold-down strap from the back

of the rangetop. Attach one end of the strap

to the back of the rangetop.

,Secure the other end of the strap as high as

possible to the cabinet back wall or adjacent

cabinet. Keep the strap as short as possible for

better security.

4

Back Wall

Hold-Down

Strap

Location

and

Attachment

STEP 3 CONNECT RANGETOP TO GAS

AWARNING

Do not use a flame to check for gas leaks.

A manual shut-off valve must be installed where

it will be accessible.

Assure that gas is turned off at the shut-off

valve.

, Install the supplied pressure regulator onto the end

of the gas inlet.

,You can install a 90 ° elbow (not provided) onto the

gas inlet and route the gas connections to avoid

interference with drawers or other cabinetry

features. However, it is not recommended because

it will result in a drop in gas pressure.

,Make sure the regulator is installed in the right

direction. See arrow on the underside of the

regulator.

NOTE: Instead of using solid piping to connect

to pressure regulator, an approved flexible metal

appliance connector may be used between the pipe

stub and the shut-off valve to the pressure regulator,

if local codes permit.

.Turn on gas and check for leaks:

-Use a liquid leak detector at all joints and

connections in the system.

\\\\\\.

RangetopBurnerBox

1/2" N.RT.

GasInlet

Regulator

(Supplied)

Ii l SolidPiping

or Flexible

Connector

Shut-0ff

Valve

PipeStubFrom

HouseGasSupply

IMPORTANT: Disconnect the rangetop and the

individual shut-off valve from the gas supply piping

system during any pressure testing of that system

at test pressures greater than 1/2 psig. Isolate

the rangetop from the gas supply piping system

by closing the individual manual shut-off valve

to the rangetop during any pressure testing

of the gas supply piping system at test pressures

equal to or less than 1/2 psig.

10

Installation

STEP4 CONNECT ELECTRICAL

, Plug power cord into properly grounded

receptacle.

, Press the button on the left side of the control

panel. The lights above the knobs should

illuminate.

STEPS CHECK BURNERS

Check to be sure that burner heads and caps

are securely seated.

Burner Cap ProperlySeated

Burner Cap Not Properly Seated

,Check for proper ignition:

- Push in one control knob and turn to LITE

position.

- The igniter will spark and the burner will light;

the igniter will cease sparking when the burner

is lit.

- First test may require some time, while air

is flushed out of the gas line.

- Turn knob to OFF.

- Repeat the procedure for each burner.

IMPORTANT: If the igniter electrodes continue

to spark after the burners are lit, check that

each burner component is assembled properly.

Refer to the Owner's Manual.

,Burner flames should be blue and stable with no

yellow tips, excessive noise or lifting of the flame

from the burner. If any of these conditions exist,

check that the burner ports are not blocked.

If one of these conditions continues, call for

service.

FINALIZE INSTALLATION

Place the burner grates over the burners.

The grates should be seated and should not rock.

The griddle is secured with screws. It is designed

to be stationary and should not be removed.

The griddle has two leveling screws beneath

the rear flue cover that can be used to adjust

to the desired slope.

Griddle Flue Cover

The two inner screws are clamping screws for

securing the griddle in place. Loosen these two

screws before leveling. Do not remove these two

screws.

The two outer screws are leveling screws. Do not

remove these two screws. They can be turned to

level the griddle or to provide a forward slope to

help grease and oils to drain away from the food

being cooked.

After leveling the griddle, hand-tighten the

clamping screws; do not over-tighten.

11

INSTALLATION CHECKLIST

[] Hake sure all controls are left in the OFF

position.

[] Hake sure the flow of combustion and

ventilation air to the rangetop is unobstructed.

[] The serial plate for your rangetop is located

on the bottom of the rangetop. In addition

to the model and serial numbers, it tells you

the ratings of the burners and the type of fuel

and pressure the rangetop was adjusted

for when it left the factory.

[] Recheck Steps:

Double check to make sure everything

in this manual has been completed. Rechecking

steps will ensure safe use of the rangetop.

ZX12B30PSS,ZX12B36PSS,ZX12B48PSS AccessoryInstallation

OPTIONAL ACCESSORIES--12" HIGH BACKSPLASH

AWARNING:

To prevent ignition of combustible materials,

the entire back wall above the range must

be protected by a backsplash constructed

of non-combustible material.

This stainless steel backsplash accessory

must be installed in combination with a custom,

non-combustible backsplash built beyond

the 12" height of the backsplash.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

iMPORTANT: Save these instructions for local

inspector's use.

IMPORTANT: OBSERVE ALL GOVERNING CODES

AND ORDINANCES.

NOTE TO iNSTALLER: Be sure to leave these

instructions with the Consumer.

NOTE TO CONSUMER: Keep these instructions

with your Owner's Manual for future reference.

This kit provides for the installation of a 12"

high backsplash for 30", 36" or 48" Monogram

Professional Ranges and Rangetops.

TOOLS AND MATERIALS REQUIRED

,Gloves to protect against sharp edges

,T-15 and #2 Phillips screwdrivers Wall Support

,Drill with 3/32" and 9/64" bits Panel

,Safety glasses

, Level

,Pencil

This Kit Includes

,Wall support panel

,Cover panel

, Hardware package with

- 5 Stainless Steel Torx 15 #8

self-tapping screws

- 5 Phillips #2 pan head wood

#10 screws

Hardware

Package

INSTALL 12" BACKSPLASH

A WARNING: Thisbacksplashmust

be securely fastened to the wall. Failure to do

so could result in damage or personal injury.

, Install and level the range or rangetop and the range

hood according to the installation instructions.

, Remove the backsplash packaging and

protective film.

, Use a level to pencil a horizontal line on the wall, 1/8"

above the range or rangetop. The 1/8" gap allows

the cover panel to overlap the wall support panel.

, Locate wall studs on each side. Where studs are not

available, plan to use wall anchors (not provided).

,Align the wall support panel on the marked

horizontal line and centered left to right.

,The wall support panel must be secured to the wall

at all 4 corners. Use wood screws (provided) or wall

anchors (not provided) to secure the support panel

to the wall.

, Place the cover panel over the wall support

panel and secure with Torx screws (provided).

Install 2 screws on each side.

!/8"

Install 4

Wood Screws

Wall Support

Panel

Wall

Support

Panel

Cover Panel

12

ZXADJB30PSS,ZXADJB36PSS,ZXADJB48PSSAccessory Installation

ACCESSORIES--30" TO 36" ADJUSTABLE BACKSPLASH (not included)

AWARNING:

To prevent ignition of combustible materials,

the entire back wall above the range must

be protected by a backsplash constructed

of non-combustible material.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

IMPORTANT: Save these instructions for local

inspectoFs use.

IMPORTANT: OBSERVEALL GOVERNING CODES

AND ORDINANCES.

NOTE TO INSTALLER: Be sure to leave these

instructions with the Consumer.

NOTE TO CONSUMER: Keep these instructions

with your Owner's Manual for future reference.

,This bocksplosh adjusts to fit the space between

the top of the range and the bottom of the hood,

from 30" Min. to 36" Max. height.

, Maximum shelf load-bearing weight is 40 Ibs.

TOOLS AND MATERIALS REQUIRED

, Gloves to protect against sharp edges

,T-15 and #2 Phillips screwdrivers

, Drill with 3/32" and 9/64" bits

, Safety glosses

, Level Top

, Pencil with Shelf

Top Wall

Support

This Kit Includes

,Top wall support

, Bottom wall support

,Top cover with shelf

, Bottom cover

, Hardware package with

- 9 Stainless Steel Torx 15 #8

self-topping screws

- 9 Phillips #2 pan head wood #10 screws

- 3 Stainless Steel #2 truss head

#10 screws (for alternate

installation method)

Bottom Wall Support

Hardware

Package

INSTALL THE WALL SUPPORT PANELS

A WARNING: The wall support panels

must be securely fastened to the wall. Failure to

do so could result in damage or personal injury.

IMPORTANT:Thisbacksplash isdesignedto coverthe wall

between the bottom of the hood and the top of the range.

Thevent hood should be installed over the rangetop or

range before installing this backsplash.

. Install and levelthe Range/Rangetop according

to the product installation instructions.

Removebacksplash packaging and protective film.

Locate wall studson each side.Where studs are not

available, plan to usewall anchors (not provided).

Usea levelto pencil 2 horizontal lineson the wall,

one 1/8" below the vent hood and the other !/8" above

the Range/Rangetop.This 1/8" spaceallows the cover

panelsto overlap the wall supports.

. Securethe top wall support _anelto the wall with 4 wood

screws,through the outermost studs.

Use4 wood screws to secure the bottom wall support

panel.Thecenter slot should be positioned at the top.

Thegap between the top and bottom support panels

will be covered by the top cover with shelf.

Secure the

top panel to

the wall with 4

wood screws

Wood Secure the

Screws bottom panel

to the wall

with 4 wood

screws

13

ZXADJB30PSS,ZXADJB36PSS,ZXADJB48PSSAccessory Installation

INSTALL COVER PANELS

See alternate method if side access is blocked.

, Hold the bottom cover over the bottom support

while driving one screw (provided)into each side.

, Place the top cover with shelf over the top wall

support. Ifyou have access to the sides, secure

the panel with two screws on each side.

, Secure the top cover with shelf to the top

support with screws through the front of the panel,

at the top corners. Use one screw on each side.

Install

Screw

Install

Screw

Install Corner Screws

INSTALL COVER PANELS {cont.)

ALTERNATEMETHOD:When side access is blocked

, Install bottom cover over the bottom support while

driving one screw into each side.

, Hold top cover in place while marking screw

locations, just below shelf support and onto bottom

cover.

, Remove the shelf and drill a 9/64" diameter

hole in the pencil-marked locations.

, Mount the top cover over the top support

and secure the front cover with screws through

the drilled holes on each side.

, Install screws through each top corner.

Hark Screw

Locations for

Alternate Method

InstallScrew in Top Corneron EachSide

_ Shelf

14

Page is loading ...

NOTE:While performing installations described inthis book,

safety glasses or goggles should beworn.

For Monogram _local service in your area, call

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor

at General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

REMARQUE: Jorsquevous proc6dez aux installations

abord6es dans ce manuel, il est fortement recommand6

de porter des lunettes de s6curit&

Pour contacter le service de ddpannage Monogram _

le plus proche de chez vous, veuillez appeler

le 1.800.444.1845.

REMARQUE:la philosophie de General Electric fait la

part belle 6 I'innovation. C'est pourquoi les mat6riau×, les

caract6ristiques et I'apparence e×t6rieure peuvent faire

I'objet de modifications sans pr6avis.

NOTA: Mientras efectOa las instaJaciones descriptas en este

libra, deben utilizarse galas o lentes de seguridad.

Para servicio tdcnico local Monogram ° en su drea,

Ilame al 1.800.444.1845.

NOTA: Lamejora de los productos es un esfuerzo continua

para General Electric. Par Io tanto, los materiales,

la apariencia y los especificadones pueden suffir cambios

sin previo aviso.

Printed in Mexico

GE Consumer & Industrial

Appliances

General Electric Company

Louisville, KY40225

GEAppliances.com

GE ZGU364LDP6SS Installation guide

This manual is also suitable for

GE ZGU364LDP6SS Installation guide

in other languages

Related papers

Other documents