GE ZGU484NGPSS Installation guide

Page is loading ...

2

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT³ Save these instructions for

local inspector’s use.

•

IMPORTANT³Observe all governing

codes and ordinances.

• Note to Installer³Be sure to leave these

instructions with the Consumer.

• Note to Consumer³ Keep these instructions

with your Owner’s Manual for future reference.

• Completion Time³1 to 3 hours.

• Proper installation is the responsibility of

the installer. Product failure due to improper

installation is not covered under the warranty. See

Owner’s Manual for warranty information.

WARNING

This appliance must be properly grounded.

Follow

directions in ”Electric Supply” of this manual. Failure to do so

may result in electric shock.

For Monogram local service in your area,

1.800.444.1845.

For Monogram Service in Canada, call

1.800.561.3344.

For Monogram Parts and Accessories, call

1.800.626.2002.

If you received a damaged rangetop, you should

contact your dealer.

In the Commonwealth of Massachusetts:

• This product must be installed by a licensed

plumber or gas fitter.

• When using ball type gas shut off valves, they

shall be T-handle type.

• A flexible gas connector, when used, must not

exceed 3 feet.

Vent hood Combinations:

It is recommended that these rangetops be installed

in conjunction with a suitable overhead vent hood.

• Install a hood with at least 1200 CFM above a 48”

wide rangetop

.

• Install a hood with at least 600 CFM above a 36”

rangetop.

Due to the high heat capacity of this unit, particular

attention should be paid to the hood and ductwork

installation to assure it meets local building codes.

WARNING:

Do not install this product with an air curtain hood or

other range hood that operates by blowing air down on

the cooktop. This airflow may interfere with operation of

the gas burners resulting in fire or explosion hazard.

Clearances to horizontal surfaces above the range,

measured to the cooking surface are below. Failure to

comply may result in fire hazard.

• Installations without a hood require 48” minimum

to combustibles.

• A custom hood installation with exposed

horizontal combustibles surfaces must have an

Auto-On feature.

• For other installations with a hood, refer to

hood installation instructions for specific hood

clearances.

CAUTION:

These rangetops are extremely heavy. Due to the

weight and size of the rangetop and to reduce the

risk of personal injury or damage to the product:

TWO PEOPLE ARE REQUIRED FOR PROPER

INSTALLATION.

Installation must conform with local codes. In the

absence of local codes, the rangetop must comply

with the National Fuel Gas Code, ANSIZ223.1/

NFPA 54, latest edition and National Electrical

Code ANSI/NFPA 70 latest addition. In Canada,

installation must conform with the current Natural

Gas Installation Code, CAN/CGA-B149.1 or the current

Propane Installation Code, CAN/CGA-B149.2, and

with local codes where applicable. This rangetop has

been design-certified by CSA International according

to ANSI Z21.1, latest edition and Canadian Gas

Association according to CAN/CGA-1.1 latest edition.

Leak testing of the appliance shall be conducted

according to the manufacturer’s instructions.

If sold outside the U.S. and Canada:

WARNING: If you wish to use this

product with Liquefied Petroleum (LP) gas

containing greater than 10% butane, you must

purchase the butane conversion kit

#WB28K10589. To order, please call

1.888.664.8403 or 1.787.276.4051.

Failure to do so

may result in carbon monoxide or fire hazard.

CONTENTS

Design Information

Models Available ......................................................................3

Backsplash Accessories .......................................................3

Product Dimensions and Clearances

for 48” Wide Models ...............................................................4

Product Dimensions and Clearances

for 36” Wide Models ...............................................................5

Installation Options ...............................................................6

Installation Preparation

Tools and Materials Required ...........................................7

Power Supply Locations .....................................................7

Remove Packaging .................................................................8

Installation Instructions

Step 1, Cut the Countertop Opening ..............................9

Step 2, Install the Rangetop ............................................10

Step 3, Connect Rangetop to Gas ................................10

Step 4, Connect Electrical .................................................11

Step 5, Check Burners .......................................................11

Finalize Installation ..............................................................11

Installation Checklist ...........................................................11

Install the Rangetop Backsplash Accessory............12

Install the Adjustable

Backsplash Accessory ................................................13, 14

Gas Conversion .............................................................15–17

MODELS AVAILABLE

Monogram rangetops are factory set for natural

gas or LP gas. Order the model for your installation

situation.

48” Natural Gas Models:

ZGU484NG – 4 gas burners, grill and griddle

ZGU486NR – 6 gas burners and grill

ZGU486ND – 6 gas burners and griddle

48” LP Gas Models:

ZGU484LG – 4 gas burners, grill and griddle

ZGU486LR – 6 gas burners and grill

ZGU486LD – 6 gas burners and griddle

36” Natural Gas Models:

ZGU364ND – 4 gas burners and griddle

ZGU364NR – 4 gas burners and grill

ZGU366N – 6 gas burners

36” LP Gas Models:

ZGU364LD – 4 gas burners and griddle

ZGU364LR – 4 gas burners and grill

ZGU366L – 6 gas burners

3

Design Information

30” to 36” Adjustable Height

Backsplash With Shelf

ZXADJB48PSS, for 48” wide rangetops

ZXADJB36PSS, for 36” wide rangetops

12” High Backsplash

ZX12B48PSS, for 48” wide rangetops

ZX12B36PSS, for 36” wide rangetops

BACKSPLASH ACCESSORIES

All models require 12” minimum clearance to a

vertical combustible surface at the rear. If clearance

is less than 12”, the entire surface of the back wall

above the countertop and the full width of the

rangetop must be protected by a backsplash. The

backsplash must be constructed of non-combustible

material, such as metal, ceramic tile, brick, marble

or other stone.

Two Backsplash Accessories Available:

• The 12” high stainless steel backsplash accessory

is available. Use this backsplash in combination

with a custom, non-combustible backsplash built

beyond the 12” height. The combined height of the

backsplash accessory and the custom backsplash

must reach the bottom of a hood, or when there is

no hood, to 48” above the cooking surface.

• An adjustable 30” to 36” high backsplash with

shelf is also available. This backsplash fills in the

space between the top of the rangetop and the

bottom of the hood. The shelf is positioned so

that heat lamps from the bottom of a Monogram

professional hood are directed towards the shelf.

4

PRODUCT DIMENSIONS AND CLEARANCES FOR 48” MODELS

Design Information

27-1/2” to

Front of

Bullnose

8-1/2”

Height

22-3/4” Min.

2-1/2”

8”

7/8”

Universal Utility Locations

2”

17”

16”

Locate gas

inlet on back

wall or on

floor 2” from

back wall.

12” Minimum

Each Side

46-1/4”

48” Min. to

Combustibles

12” Minimum to

Combustibles or 0”

to non-combustible

material above the

cooking surface

0”

Clearance

* The opening between a 4” high

backsplash must be 48” to allow the

rangetop to slide back against the wall.

13” Max.

18” Min.

48” Minimum

to Combustibles

12” Minimum to

Adjacent Wall

47-7/8” Width

WARNING:

Installations without a hood

require 48

”

minimum to combustibles

above the rangetop. A custom hood

installation with exposed horizontal

combustible surfaces must have

an Auto-On feature. Refer to hood

installation instructions for specific

hood clearances.

The surface of the entire back wall

above the countertop and below

the hood must be covered with

a non-combustible material such

as metal, ceramic tile, brick, marble

or other stone.

*48”

Non-

combustible

material

48”

ADDITIONAL CLEARANCES:

Allow 12” minimum clearance to an

adjacent wall on each side.

Working areas adjacent to the rangetop

should have 18” minimum clearance

between countertop and the bottom of

the wall cabinet.

For island installation, maintain 2-1/2

in. minimum from cutout to back edge

of countertop and 3 in. minimum from

cutout to side edges of countertop (see

top view).

Back

3” Min.

Island

Cutout

Top View

3” Min.

2-1/2” Min.

PRODUCT DIMENSIONS AND CLEARANCES FOR 36” MODELS

Design Information

35-7/8” Width

8-1/2”

Height

5

Universal Utility Locations

2”

17”

16”

Locate gas

inlet on back

wall or on

floor 2” from

back wall.

22-3/4” Min.

2-1/2”

8”

1/2”

12” Minimum

Each Side

35”

* The opening between a 4” high

backsplash must be 36” to allow

the rangetop to slide back against

the wall.

13” Max.

18” Min.

48” Minimum

to Combustibles

12” Minimum to

Adjacent Wall

WARNING:

Installations without a hood

require 48

”

minimum to combustibles

above the rangetop. A custom hood

installation with exposed horizontal

combustible surfaces must have

an Auto-On feature. Refer to hood

installation instructions for specific

hood clearances.

The surface of the entire back wall

above the countertop and below the

hood must be covered with a non-

combustible material such as metal,

ceramic tile, brick, marble or other

stone.

*36”

Non-

combustible

material

27-1/2” to

Front of

Bullnose

48” Min. to

Combustibles

0”

Clearance

12” Minimum to

Combustibles or 0”

to non-combustible

material above the

cooking surface

36”

ADDITIONAL CLEARANCES:

Allow 12” minimum clearance to an

adjacent wall on each side.

Working areas adjacent to the rangetop

should have 18” minimum clearance

between countertop and the bottom of

the wall cabinet.

For island installation, maintain 2-1/2

in. minimum from cutout to back edge

of countertop and 3 in. minimum from

cutout to side edges of countertop (see

top view).

Back

3” Min.

Island

Cutout

Top View

3” Min.

2-1/2” Min.

*

**

8”

Countertop

Level

6

Design Information

Cooktop

1/2” Above Adjacent

Countertops.

Cooktop

1/2” Above Adjacent

Countertops.

Rangetop

1/2” Above Adjacent

Countertops

1/2” Above Adjacent

Countertops

Rangetop

Control panel projects forwards from

standard depth cabinets.

Front of deep cabinets can align with control

panel beveled edge.

** Maximum countertop cutout depth

from the back of the rear trim

to the back edge of chamfer at the

sides of the control panel - typically,

the maximum countertop cutout depth

(front to back). Minimum countertop

cutout depth is 25-1/4”.

* Minimum cabinet cutout depth from

the back of the rear trim to the back

finished edge of the control panel -

typically, the minimum cabinet depth

(front to back). Maximum cabinet cutout

depth is 26” minus the countertop

overhang.

†

Include the overhang of the rear trim when countertop continues behind the product.

The overhang is decorative only. The weight of the rangetop is fully supported by the side trims.

INSTALLATION OPTIONS

†

Back edge

of chamfer

Finished back edge

of control panel

POWER SUPPLY LOCATIONS

Gas Supply:

• The natural gas models are designed to operate at 5”

water column pressure. For proper operation, the

pressure of the natural gas supplied to the regulator

must be between 7” and 13” water column.

• The LP models are designed to operate at 10” water

column pressure. For proper operation, the pressure

of the LP gas supplied to the regulator must be between

11” and 13” water column.

• Locate the pipe stub on the back wall or floor

(see “Product Dimensions and Clearances”). Use 5-foot

maximum length, 5/8” O.D. flexible gas supply line

(3-foot in Massachusetts).

• Install a manual shut-off valve in the gas line

(not provided), in an easily accessible location. Make sure

the homeowner knows where and how to shut off the gas

supply to the rangetop.

Electric Supply:

These rangetops must be supplied with 120 volt, 60 Hz.,

and connected to a dedicated, properly grounded branch

circuit protected by a 15 amp circuit breaker or time

delay fuse.

The power cord of this appliance is equipped with a

three-prong (grounding) plug which mates with a standard

three-prong grounding wall receptacle to minimize the

possibility of shock hazard from this appliance.

If the electrical service provided does not meet the above

specifications, it is recommended that a licensed electrician

install an approved outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT

OR REMOVE THE THIRD

(GROUND) PRONG FROM

THE POWER CORD.

DO NOT USE AN EXTENSION

CORD WITH THIS APPLIANCE.

• Locate the electric supply

within the area shown or

within reach of the rangetop’s four-foot power cord.

• To avoid tangling cord with items stored in the cabinet,

locate the receptacle on rear wall, inside the cabinet.

7

Installation Preparation

MATERIALS PROVIDED

Regulator

Hold-Down

Strap

TOOLS REQUIRED

Adjustable Wrench

1/4” Driver or

Wrench

Safety Glasses

Drill and

Appropriate Bits

Measuring Tape

Phillips #2

Screwdriver

Saber Saw

Carpenter’s Square

MATERIALS REQUIRED (not provided)

Shut-Off

Valve

Pipe Fittings

5-foot maximum length, 5/8” O.D. CSA-approved

flexible metal gas supply

(3-foot maximum length in Massachusetts only)

NOTE: Purchase new flexible line; do not use

previously used flexible gas line.

Joint

Sealant

Level

Hand Truck

8

Installation Preparation

REMOVE PACKAGING

• Cut the ties holding the grill grate to the grill frame.

• Lift off burner caps and remove foam pad,

then lift off burner heads and remove foam pad.

Griddle Flue Cover

Grease Troughs

Ties

Remove Foam Pads

CAUTION

Stand clear. The ends of the cut metal banding may

snap toward you.

• Cut the metal banding.

• Remove packaging tape and foam.

Dispose of packaging materials properly.

• Remove grill/griddle covers, grill grate and burner

grates.

• Lift out cast-iron griddle flue cover, grease

troughs and pads.

Dimensions

A (Dia.) B C D

36” Rangetop 7-3/8” 1-1/2” 7-1/2” 11-1/8”

48” Rangetop 8-1/4” 1-1/2” 7-1/2” 11-1/8”

Measure carefully when cutting the countertop.

Make sure sides of the opening are parallel.

• Allow 8” free space below the top surface of the countertop.

• Allow additional clearances below the burner box

to install the regulator and make house supply

connections. Use a 90° elbow to route the gas

connections and limit interference with drawers

or other cabinetry features.

• These rangetops are designed to hang from

the countertop by their side flanges.

• Smooth any rough edges on the countertop before

installing the rangetop.

– Formica countertop edges must be finished.

The countertop must be strong enough to support

the weight of the rangetop.

Cutout Opening with False Bottom

• You can construct the cutout with a false bottom to

conceal the bottom of the rangetop.

– Build the false bottom using a solid material; cut a

7-1/2” x 11-1/8” hole in the left rear corner for the gas

inlet and power cord clearances.

9

Installation

48” wide models are designed to fit in 48” or wider base cabinets 36” wide models are designed to fit in 36” or wider base cabinets

CUT THE COUNTERTOP OPENING

STEP 1

10

Installation

INSTALL RANGETOP

• Slide the rangetop into the opening. Make sure the

rangetop is evenly seated and supported.

• A hold-down strap with screws is provided to

secure the rangetop to the rear or side cabinet

walls.

• Remove the hold-down strap from the back of the

rangetop. Attach one end of the strap to the back

of the rangetop.

• Secure the other end of the strap as high as

possible to the cabinet back wall or adjacent

cabinet. Keep the strap as short as possible for

better security.

STEP 2

CONNECT RANGETOP TO GAS

WARNING

Do not use a flame to check for gas leaks.

A manual shut-off valve must be installed where

it will be accessible.

Assure that gas is turned off at the shut-off

valve.

• Install the supplied pressure regulator onto the end

of the gas inlet.

• You can install a 90° elbow (not provided) onto

the gas inlet and route the gas connections to

avoid interference with drawers or other cabinetry

features. However, it is not recommended because it

will result in a drop in gas pressure.

• Make sure the regulator is installed in the right

direction. See arrow on the underside of the

regulator.

NOTE: Instead of using solid piping to connect to

pressure regulator, an approved flexible metal

appliance connector may be used between the pipe

stub and the shut-off valve to the pressure regulator,

if local codes permit.

• Turn on gas and check for leaks:

– Use a liquid leak detector at all joints and

connections in the system.

IMPORTANT: Disconnect the rangetop and the

individual shut-off valve from the gas supply piping

system during any pressure testing of that system

at test pressures greater than 1/2 psig. Isolate the

rangetop from the gas supply piping system by

closing the individual manual shut-off valve to the

rangetop during any pressure testing of the gas

supply piping system at test pressures equal to or less

than 1/2 psig.

STEP 3

Regulator

(Supplied)

Note: Pipe stub extends

about 1” below burner

box.

Solid Piping

or Flexible

Connector

Shut-Off

Valve

Pipe Stub From

House Gas Supply

Rangetop Burner Box

1/2” N.P.T.

Gas Inlet

Back Wall

Hold-Down

Strap

Location and

Attachment

11

Installation

CONNECT ELECTRICAL

• Plug power cord into properly grounded

receptacle.

• Press the button on the left side of the control

panel. The lights above the knobs should

illuminate.

STEP 4

FINALIZE INSTALLATION

Place the burner grates over the burners. The

grates should be seated and should not rock.

The griddle is secured with screws. It is designed to

be stationary and should not be removed.

The griddle has two leveling screws beneath the

rear flue cover that can be used to adjust to the

desired slope.

The two inner screws are clamping screws for

securing the griddle in place. Loosen these two

screws before leveling. Do not remove these two

screws.

The two outer screws are leveling screws. Do not

remove these two screws. They can be turned to

level the griddle or to provide a forward slope to

help grease and oils to drain away from the food

being cooked.

After leveling the griddle, hand-tighten the

clamping screws; do not over-tighten.

INSTALLATION CHECKLIST

■ Make sure all controls are left in the OFF

position.

■ Make sure the flow of combustion and

ventilation air to the rangetop is unobstructed.

■ The serial plate for your rangetop is located

on the bottom of the rangetop. In addition to

the model and serial numbers, it tells you the

ratings of the burners and the type of fuel and

pressure the rangetop was adjusted for when it

left the factory.

■ Recheck Steps:

Double check to make sure everything in this

manual has been completed. Rechecking steps

will ensure safe use of the rangetop.

CHECK BURNERS

Check to be sure that burner heads and caps are

securely seated.

• Check for proper ignition:

– Push in one control knob and turn to LITE

position.

– The igniter will spark and the burner will light; the

igniter will cease sparking when the burner is lit.

– First test may require some time, while air is

flushed out of the gas line.

– Turn knob to OFF.

– Repeat the procedure for each burner.

IMPORTANT: If the igniter electrodes continue to

spark after the burners are lit, check that each

burner component is assembled properly. Refer to

the Owner’s Manual.

• Burner flames should be blue and stable with no

yellow tips, excessive noise or lifting of the flame

from the burner. If any of these conditions exist,

check that the burner ports are not blocked. If one

of these conditions continues, call for service.

STEP 5

Burner Cap Not Properly Seated

Burner Cap Properly Seated

Griddle Flue Cover

Clamping Screws

Leveling Screws

12

ZX12B30PSS, ZX12B36PSS, ZX12B48PSS Accessory Installation

237,21$/$&&(6625,(6³” HIGH BACKSPLASH

TOOLS AND MATERIALS REQUIRED

• Gloves to protect against sharp edges

• T-15 and #2 Phillips screwdrivers

• Drill with 3/32” and 9/64” bits

• Safety glasses

• Level

• Pencil

This Kit Includes

• Wall support panel

• Cover panel

• Hardware package with

– 5 Stainless Steel Torx 15 #8 self-

tapping screws

– 5 Phillips #2 pan head wood #10 screws

Wall Support

Panel

Hardware

Package

INSTALL 12” BACKSPLASH

WARNING:

This backsplash must be

securely fastened to the wall. Failure to do

so could result in damage or personal injury.

•

Install and level the range or rangetop and the

range hood according to the installation instructions.

•

Remove the backsplash packaging and protective

film.

•

Use a level to pencil a horizontal line on the wall,

1/8” above the range or rangetop. The 1/8” gap

allows the cover panel to overlap the wall support

panel.

•

Locate wall studs on each side. Where studs are not

available, plan to use wall anchors (not provided).

•

Align the wall support panel on the marked

horizontal line and centered left to right.

•

The wall support panel must be secured to the wall

at all 4 corners. Use wood screws (provided) or wall

anchors (not provided) to secure the support panel

to the wall.

•

Place the cover panel over the wall support panel

and secure with Torx screws (provided). Install 2

screws on each side.

Install 4

Wood Screws

1/8”

Install T-15

Screws

Wall

Support

Panel

Wall Support

Panel

Cover Panel

WARNING:

To prevent ignition of combustible materials,

the entire back wall above the range must be

protected by a backsplash constructed of non-

combustible material.

This stainless steel backsplash accessory must

be installed in combination with a custom, non-

combustible backsplash built beyond the 12”

height of the backsplash.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

IMPORTANT: Save these instructions for local

inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES

AND ORDINANCES.

NOTE TO INSTALLER: Be sure to leave these

instructions with the Consumer.

NOTE TO CONSUMER: Keep these instructions

with your Owner’s Manual for future reference.

This kit provides for the installation of a 12”

high backsplash for 30”, 36” or 48” Monogram

Professional Ranges and Rangetops.

Center

Arrow

13

TOOLS AND MATERIALS REQUIRED

• Gloves to protect against sharp edges

• T-15 and #2 Phillips screwdrivers

• Drill with 3/32” and 9/64” bits

• Safety glasses

• Level

• Pencil

This Kit Includes

• Top wall support

• Bottom wall support

• Top cover with shelf

• Bottom cover

• Hardware package with

– 9 Stainless Steel Torx 15 #8

self-tapping screws

– 9 Phillips #2 pan head wood #10 screws

– 3 Stainless Steel #2 truss head

#10 screws (for alternate

installation method)

WARNING:

To prevent ignition of combustible materials,

the entire back wall above the range must be

protected by a backsplash constructed of non-

combustible material.

$&&(6625,(6³” TO 36” ADJUSTABLE BACKSPLASH (not included)

ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory Installation

INSTALL THE WALL SUPPORT PANELS

W

ARNING:

The wall support panels

must be securely fastened to the wall. Failure to

do so could result in damage or personal injury.

IMPORTANT: This backsplash is designed to cover the wall

between the bottom of the hood and the top of the range.

The vent hood should be installed over the rangetop or

range before installing this backsplash.

• Install and level the Range/Rangetop according to the

product installation instructions.

• Remove backsplash packaging and protective film.

• Locate wall studs on each side. Where studs are not

available, plan to use wall anchors (not provided).

• Use a level to pencil 2 horizontal lines on the wall, one

1/8” below the vent hood and the other 1/8” above the

Range/Rangetop. This 1/8” space allows the cover panels

to overlap the wall supports.

• Secure the top wall support panel to the wall with 4 wood

screws, through the outermost studs.

• Use 4 wood screws to secure the bottom wall support

panel. The center slot should be positioned at the top.

The gap between the top and bottom support panels will be

covered by the top cover with shelf.

1/8”

Secure the

top panel to

the wall with 4

wood screws

1/8”

Secure the

bottom panel

to the wall

with 4 wood

screws

Center

Arrow

Wood Screws

Wood

Screws

Top Wall

Support

Top Cover

with Shelf

Bottom Cover

Bottom Wall Support

Hardware

Package

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

IMPORTANT: Save these instructions for local

inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND

ORDINANCES.

NOTE TO INSTALLER: Be sure to leave these

instructions with the Consumer.

NOTE TO CONSUMER: Keep these instructions with

your Owner’s Manual for future reference.

• This backsplash adjusts to fit the space between

the top of the range and the bottom of the hood,

from 30” Min. to 36” Max. height.

• Maximum shelf load-bearing weight is 40 lbs.

14

INSTALL COVER PANELS (cont.)

ALTERNATE METHOD: When side access is blocked

• Install bottom cover over the bottom support while

driving one screw into each side.

•

Hold top cover in place while marking screw

locations, just below shelf support and onto bottom

cover.

•

Remove the shelf and drill a 9/64” diameter hole in

the pencil-marked locations.

•

Mount the top cover over the top support and

secure the front cover with screws through the

drilled holes on each side.

•

Install screws through each top corner.

ZXADJB30PSS, ZXADJB36PSS, ZXADJB48PSS Accessory Installation

INSTALL COVER PANELS

See alternate method if side access is blocked.

• Hold the bottom cover over the bottom support

while driving one screw (provided) into each side.

•

Place the top cover with shelf over the top wall

support. If you have access to the sides, secure the

panel with two screws on each side.

•

Secure the top cover with shelf to the top support

with screws through the front of the panel, at the

top corners. Use one screw on each side.

Shelf

Install

Screw

Cover Panel

Install

Screw

Mark Screw

Locations for

Alternate Method

Install Screw in Top Corner on Each Side

Install Screw

on Each Side

Install Corner Screws

15

TOOLS YOU NEEDED FOR CONVERSION

2

CONVERT THE REGULATOR

Disconnect all electrical power at the main circuit

breaker or fuse box.

A. Remove the rear vent

trim (on ranges only) to

access the regulator.

The Rangetop

regulator is on the left bottom corner.

B. Shut off the gas supply by closing the manual shut-off

valve in the unit or at the wall.

C.

Convert the pressure regulator:

• Unscrew the cap with plunger.

• Place your thumb against flat side of the plunger and

press down to snap the plunger out of the cap.

• Carefully look at the

plunger to locate the

NAT or LP position.

• Turn the plunger over

so that the desired

gas is showing near

the bottom.

• Snap the plunger

back into the cap.

• Screw the cap back

onto the regulator.

3

CHANGE BURNER ORIFICES

INSTALLATION TIP: First remove all

orifices and then start replacing them.

This will help to prevent the possibility

that some may not be replaced.

A. Remove the burner grates,

burner caps and burner heads.

B. Loosen the top burner

orifices using a 7 mm nut

driver. Use small pliers to

carefully lift out the orifices.

The main orifice is

located low in the

center of the burner,

while the simmer

orifice is located

higher beside the

center of the burner.

DOWN

FOR OFF

NAT

LP

NAT

LP

NAT

LP

Gasket

Cap

Plunger

LP Position

NAT.

Position

Pressure Regulator

Burner Cap

Burner

Head

Spark

Igniter

Main

Orifice

Simmer

Orifice

WARNING: This conversion must be

performed by a qualified installer or gas supplier in

accordance with the manufacturer’s instructions and

all codes and requirements of the authority having

jurisdiction. Failure to follow instructions could result in

serious injury or property damage. The qualified agency

performing this work assumes responsibility for the

conversion.

WARNING: The rangetop, as shipped from

the factory, is set for use with its intended gas. If you

wish to use your rangetop with the alternate gas, you

must first replace the orifices and convert the pressure

regulator.

WARNING: The following adjustments

must be made before turning on the burner. Failure to

do so could result in serious injury. Be sure pressure

regulator has been converted as described in Step 2.

Safety Glasses

Small Flat-Head Screwdriver

(2 to 2.4 mm or 3/32” tip size,

60 mm long)

Crescent Wrench

1/4” and 7mm

Nutdrivers

Installation Convert Natural Gas to LP Gas Operation

Instructions Convert LP Gas to Natural Gas Operation

Small Pliers

1/2” Deepwell

Socket Wrench

Philips

Screwdriver

ORIFICE HOLDER

The range orifice holder is

located behind the front

access panel at the bottom

of the range.

The rangetop orifice holder

is located inside the range insulation cover.

Additional orifices may be present. Use only the orifices

specified in the instructions for your range or rangetop.

Burner Base

Griddle

Orifice

Grill

Orifice

Burner Orifices

1

Range Regulator

16

4 **

CHANGE GRILL ORIFICE

(cont.)

A. Remove the grill cover,

grates and grate frame. Lift

the radiant baffle straight

up and off.

B. Remove the 2 hex head

screws from the top of

the igniter.

• Remove one screw from

each side of the burner

surround.

• Lift out the surround.

C. Carefully push the

igniter aside and under

the burner. Do not pull

or pinch the wire.

Remove 4 burner

attachment screws, 2

at the front and 2 at the

back. Slide the burner

assembly toward the

back and out of the gas

inlet.

D. Use a 1/2” deep well

socket to remove and

replace the orifice .

Reverse these steps to

re-assemble the grill. Be

sure to place the unused

orifice in the holder for

possible future use.

E. Adjust Grill “LO” Setting

• Make certain gas and electricity to unit are turned off.

• Turn the grill knob to LO and remove the knob by

pulling straight off.

• Insert a small flat-blade screwdriver into the hole in the

center of the valve stem to engage set screw.

• To convert the LO setting from natural gas to LP, turn

the screw clockwise until it stops

(about 3/4 turn). It may be necessary

to grasp the exterior of the valve

stem with a pair of pliers to prevent

the valve stem from rotating as the

set screw is adjusted.

• To convert the LO setting from the LP

to natural gas setting, turn the screw

counterclockwise about 3/4 turn.

4 **

CHANGE GRILL ORIFICE

(if present)

Locate the 1–1/2” long Grill orifice.

Select for your gas type. LP

³

.047, NAT

³

.067

Installation Instructions for Gas Conversion

Burner

Surround

Igniter

Burner

Assembly

3

CHANGE BURNER ORIFICES (cont.)

IMPORTANT: Find your model number below. Read

each orifice label to identify and install them in the

exact locations shown.

A. Return the unused orifices to the holder. Reattach

the holder and the instruction sheet with screw in

the original storage location.

B. Replace the burner heads, caps and top grates

. On

range models, replace rear vent trim.

ZDP304 SIMMER ORIFICES

A 34SL or 51SN orifice

will be used on all burners.

ZDP364, ZDP366, ZDP484, ZDP486

SIMMER

ORIFICES

MAIN

ORIFICES

A 34SL or 51SN orifice will

be used on all burners.

Use 108XL or

190XN orifices

for all burners.

ZDP304 MAIN ORIFICES

A 84XL or

126HXN orifice

will be used

on these three

burners.

Use a 108XL

or 190XN orifice

for the right

front burner.

Remove

2 hex

head

screws

Surround

Screws

Front of Range

17

5

CHANGE GRIDDLE ORIFICE

(if present)

Locate the 3/4” long griddle orifice.

Select for your gas type. LP

³

.047, NAT

³

.076

A. Lift off the

griddle flue

cover. Remove

the 2 inside

clamping

screws.

B. Lift out the

cast-iron

grease trough.

Slide the

griddle toward

the rear and

out of the

hold-down tabs along the

bottom.

C. Carefully lift and hold

the griddle while pulling

additional length of the

capillary from the entry

hole. Stand the griddle on

end in the grease sump.

D. Remove the 2 hold-down

screws at the rear of the

burner.

Pull the burner straight

back toward the rear and

out of the gas inlet.

E. Use a 1/2” deepwell

socket to remove and replace the orifice.

Reverse these steps to reassemble the griddle.

Push excess capillary back into the entry hole.

Place the unused orifice in the holder for possible

future use.

Installation Instructions for Gas Conversion

6

ADJUST BURNER FLAMES

Normally, burners do not need further adjustment.

Make adjustments only when necessary.

A. Turn on the gas. Plug in electrical cord.

B. Turn all burners on highest setting and check the

flames. They should be blue in color. When using

LP gas, the flames may have some yellow tipping

at the ends of the flame. Foreign particles in the

gas line may cause an orange flame at first, but

this will soon disappear.

C. Turn the burner knob to “LO” while observing the

flame.

Adjust the setting of the upper row of flames using

the valve bypass screw as follows:

Adjustments must be made with two other burners

in operation on a medium setting. This prevents the

upper row of flames from being set too low, resulting

in the flame being extinguished when other burners

are turned on.

D. To adjust the flame, remove the knobs. Insert a small

flat-blade screwdriver into the hole in the center of

the valve stem to engage screw.

• If the flames are too small or flutter, turn the screw

counterclockwise.

• If the flames are too large, turn the screw

clockwise.

E. Make the adjustment by slowly turning the screw

until flame appearance is correct.

Once the conversion is complete and checked, fill out the conversion label and affix the label near the rating label. For ranges,

place the label beneath the control panel. For rangetops, place the label on the bottom of the unit.

Capillary

Front of Range

B

C

D

E

Back of Range

Griddle Flue Cover

Clamping

Screws

Leveling Screws

A

NOTE: Remove

the 2 screws

positioned on

the inside only.

Do not remove

the outermost

VFUHZV³

they are for

leveling.

Page is loading ...

Printed in Mexico

NOTA: Mientras efectúa las instalaciones descriptas en este

libro, deben utilizarse gafas o lentes de seguridad.

Para servicio técnico local Monogram

®

en su área,

llame al 1.800.444.1845.

NOTA: La mejora de los productos es un esfuerzo continuo

para General Electric. Por lo tanto, los materiales,

la apariencia y las especificaciones pueden sufrir cambios

sin previo aviso.

REMARQUE: lorsque vous procédez aux installations

abordées dans ce manuel, il est fortement recommandé

de porter des lunettes de sécurité.

Pour contacter le service de dépannage Monogram

®

le plus proche de chez vous, veuillez appeler

le 1.800.444.1845.

REMARQUE: la philosophie de General Electric fait la

part belle à l’innovation. C’est pourquoi les matériaux, les

caractéristiques et l’apparence extérieure peuvent faire

l’objet de modifications sans préavis.

NOTE: While performing installations described in this book,

safety glasses or goggles should be worn.

For Monogram

®

local service in your area, call

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

GE ZGU484NGPSS Installation guide

GE ZGU484NGPSS Installation guide

in other languages

Related papers

Other documents