ASO Safety Solutions ELMON inductive 71-242 & 71-942 Owner's manual

Type
Owner's manual

This manual is also suitable for

ASO Safety Solutions ELMON inductive 71-242 & 71-942 is a safety device used in conjunction with a travelling coil to protect people from moving gates, doors and barriers. It has induction detection and is capable of detecting conductive materials such as metal. It can be used on gates up to 5m long.

ASO Safety Solutions ELMON inductive 71-242 & 71-942 is a safety device used in conjunction with a travelling coil to protect people from moving gates, doors and barriers. It has induction detection and is capable of detecting conductive materials such as metal. It can be used on gates up to 5m long.

Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
01
ELMON KIT FITTING GUIDE
FITTING GUIDE
1
2
3
COMPONENTS
REQUIRED TOOLS
Cuers Drill M4 & M6 Tap bits Alen Keys
So far, the cable of the contact edge (OPEN/CLOSE) had to be installed along the gates entire length
to connect it to the travelling coil core (SPK 54).
A new steel cable with an additional 2 cores is now included in each kit, which helps reduce fiing
time. One end is pre-assembled with connectors for the travelling coil. An extra pair of waterproof
connectors is included at the tensioner to connect the rear travelling safety edge.
This allows safety edges at each end of the gate to be connected to the travelling coil easily, without
the need to run a long connecting cable through or along the gate.
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
02
ELMON KIT FITTING GUIDE
FITTING GUIDE
min. 25mm
min.35mm
*x*
M4
M6
X=75mm
X=25mm
X=25mmX=25mm
1A
Drill and tap M4 Hole
3A
Drill and tap M6 Hole
or bolt/tek screw
1B 1C 1D
Place the transmission cable in
slot gap.
Strip back the insulation and plug cable
cores into plug terminals.
!ONLY CLAMP THE STEEL CABLE!
1,5-2 Nm
Screw in the provided allen head bolt.
!DO NOT OVER TIGHTEN!
1,5-2 Nm
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
03
ELMON KIT FITTING GUIDE
Pass the cable through the
stationary SPK coil.
2A
18mm
Fit the clamping unit into the
tension bracket
Fix tension bracket with an M6
or a similar bolt.
1,5-2 Nm
3C
3B
3D
3F
3E
~ 20mm
Pull the Cable through the tension bracket
and clamp.
!CABLE SHOULD NOT BE LOOSE!
Clamp down the allen head screw.
!DO NOT OVER TIGHTEN!
1,5 Nm
Trim away excess steel cable.
3G
2B
3H
Adjust the clamp unit. Tighten the clamp unit to hold everything
in place.
1,5-2 Nm
Secure SPK coil bracket
appropriately.
ELMON KIT FITTING GUIDE
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
04
2C 2D
Adjust for height. Adjust for position and secure
to the ground.
Cover the components for
protection.
3E
1E
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ASO Safety Solutions ELMON inductive 71-242 & 71-942 Owner's manual

Type
Owner's manual
This manual is also suitable for

ASO Safety Solutions ELMON inductive 71-242 & 71-942 is a safety device used in conjunction with a travelling coil to protect people from moving gates, doors and barriers. It has induction detection and is capable of detecting conductive materials such as metal. It can be used on gates up to 5m long.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI