2. ASO Safety Solutions
  3. ELMON inductive 71-242 & 71-942

ASO Safety Solutions ELMON inductive 71-242 & 71-942, INDUS 71-242 & 71-942 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the ASO Safety Solutions ELMON inductive 71-242 & 71-942 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
01
ELMON KIT FITTING GUIDE
FITTING GUIDE
1
2
3
COMPONENTS
REQUIRED TOOLS
Cuers Drill M4 & M6 Tap bits Alen Keys
So far, the cable of the contact edge (OPEN/CLOSE) had to be installed along the gates entire length
to connect it to the travelling coil core (SPK 54).
A new steel cable with an additional 2 cores is now included in each kit, which helps reduce fiing
time. One end is pre-assembled with connectors for the travelling coil. An extra pair of waterproof
connectors is included at the tensioner to connect the rear travelling safety edge.
This allows safety edges at each end of the gate to be connected to the travelling coil easily, without
the need to run a long connecting cable through or along the gate.
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
02
ELMON KIT FITTING GUIDE
FITTING GUIDE
min. 25mm
min.35mm
*x*
M4
M6
X=75mm
X=25mm
X=25mmX=25mm
1A
Drill and tap M4 Hole
3A
Drill and tap M6 Hole
or bolt/tek screw
1B 1C 1D
Place the transmission cable in
slot gap.
Strip back the insulation and plug cable
cores into plug terminals.
!ONLY CLAMP THE STEEL CABLE!
1,5-2 Nm
Screw in the provided allen head bolt.
!DO NOT OVER TIGHTEN!
1,5-2 Nm
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
03
ELMON KIT FITTING GUIDE
Pass the cable through the
stationary SPK coil.
2A
18mm
Fit the clamping unit into the
tension bracket
Fix tension bracket with an M6
or a similar bolt.
1,5-2 Nm
3C
3B
3D
3F
3E
~ 20mm
Pull the Cable through the tension bracket
and clamp.
!CABLE SHOULD NOT BE LOOSE!
Clamp down the allen head screw.
!DO NOT OVER TIGHTEN!
1,5 Nm
Trim away excess steel cable.
3G
2B
3H
Adjust the clamp unit. Tighten the clamp unit to hold everything
in place.
1,5-2 Nm
Secure SPK coil bracket
appropriately.
ELMON KIT FITTING GUIDE
Technical Document Ver 2.0
Valid: 01/01/2018
Web: www.easygatesdirect.co.uk
E-Mail: info@easygatesdirect.co.uk
Phone: 0845 054 50 70
Address: Easygates Ltd, Unit 16 James Sco Rd B63 2QT
04
2C 2D
Adjust for height. Adjust for position and secure
to the ground.
Cover the components for
protection.
3E
1E
/