Parts List
— 1 —
English
TITAN ONE MINI_3.0 Installation Guide
BPTA-O11D-MINI_A3.0-BK
B-1 B-2
A-1
A-2
A-3
248
55
A
B
C
Hard Tube
C-1
Drain Tube
C-2
V3
:16
284
55
:16
The allowable variance in tube length is ± 2mm
For standard MATX mother board (24x 24cm).
For the ITX motherboard or not standard size MATX motherboard.
............1 pc
Intel Mounting Bracket
CPU Water Block
A
..........1 pc
BPTA-CPUMS-V2-SKA
A-1
A-2
...............1 set
Backplane Assembly
A-3
Fittings
B
.................2 pcs
BPTA-DOTFH1622
B-1
....................2 pcs
BPTA-15ATFH16
B-2
Accessory
C
...............................4 pcs
Hard Tube
C-1
..............................1 pc
Drain Tube
C-2
CPU set
C-3
BP-CPUPDB-AMD5MS
C-5
Thumb screw
SPRING
Thumb nut
1mm Spacer
M3x32mm Screw
SC6-32M3
Nylon cup washer
.................4 pcs
.................4 pcs
.................4 pcs
...........4 pcs
..................8 pcs
.....................4 pcs
.........................4 pcs
BPTA-MKCPUMS-1700 or
BPTA-MKCPUMS-1700-V2
C-4
Please refer to the tables on pages 5 and 16
for Hard Tubes+Motherboard compatibility.
Bitspower reserves the right to change the product design and interpretations.
These are subject to change without notice. Product colors and accessories
are based on the actual product.
EX.
I. AMD Motherboard system
— 2 —
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
Thumb screw
SPRING
CPU Block
1mm SPACER
Thumb screw
CPU Block
SC6-32M3
(for AMD AM4)
Nylon cup washer
(for AMD AM4)
Original
backplane
SPRING
1mm SPACER
Thumb Nut
96
90
48
54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4 + Legacy Installation
DRGB LED
IN
OUT
DRGB PIN on Motherboard or other equipment.
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
Do not over-tighten the thumb
screws. The springs should be
slightly compressed, with visible
gaps in the spring coils. Over-tight-
ening may result in poor contact
between the water block and CPU.
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
— 3 —
1
4
2
3
CPU Water block
Installation(AM5)
BP-CPUPDB-AMD5MS
C-5
1
42
3
Thumb screw.................4 PCS
Stud..........................4 PCS
Spring .............................4 PCS
Washer.....................4 PCS
Use an appropriate amount
of Thermal Compound
CPU
— 4 —
Hard tube BPTA-15ATFH16
II. Pre-Fill Installation
Step 1
Step 2
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
Compatible with all mATX boards.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
Hard tube BPTA-15ATFH16
Before installing the water cooling parts for the
graphics card, please remove this part.
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
5
— —
Upside downHead up
Hard Tube Motherboard
Mounting orientation
(CPU block position)
55x248 Head up All mATX motherboards
55x248 Head up PRO B650M-A WIFIMSI
In the event that the CPU Block is oriented higher than the
maximum default height of the Distribution Blocks' sliding CPU
Terminal, it is possible to rotate the face of the Terminal 180°
into its Upside Down position. This should allow the terminal to
match the height of the CPU Block.
— 6 —
Step 1
Step 2
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
It’s removable
Before installing the water cooling parts for the
graphics card, please remove this part.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
Hard tube BPTA-15ATFH16
Compatible with all ITX boards.
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
7
— —
Upside downHead up
Hard Tube Motherboard
Mounting orientation
(CPU block position)
55x284 Head up All ITX motherboards
— 8 —
Thumb screw
SPRING
CPU Block
1mm SPACER
M3x32mm SCREW
(for Intel)
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
Thumb Nut
EX.
80
75
72
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
IN
OUT
A-2
DRGB PIN on Motherboard or other equipment.
Motherboard
Fan and DRGB RF Remote
Controller Hub (Not included)
BPTA-RFCHUB
Installation
The CPU water block has a DRGB cable, which
can be connected to the DRGB extension
cable of the radiator fans.
Fin
Base screw
Base
Top
Intel Mounting Bracket
AMD Mounting Bracket
Installation
Do not over-tighten the thumb screws. The
springs should be slightly compressed, with
visible gaps in the spring coils. Over-tighten-
ing may result in poor contact between the
water block and CPU.
Bitspower Fan and DRGB RF Remote Controller Hub
(Not included) are now available at microcenter.com
Use an appropriate amount
of Thermal Compound, - high-end
Bitspower cooling products are now
available at microcenter.com.
Step 1
Step 2
III. Intel Motherboards Titan One 3.0 is compatible with most ATX motherboards.
If not compatible, please contact Bitspower directly.
— 9 —
4
1 2
3
Assembly steps
step 1
1
2
3
Installation(LGA 1700)
C-4
BPTA-MKCPUMS-1700(If you got this version, please refer to the following installation)
Backplate ............................1 PC Adjusting Nut..........................8 PCS
Backplane Bolt .......................4 PCS
Washer...................................4 PCS
—
10
—
step 3
step 2
4
2
—
11
—
1
Assembly steps
step 1
1
2
3
Installation(LGA 1700)
BPTA-MKCPUMS-1700-V2(If you got this version, please refer to the following installation)
C-4
4
2
3
5
Backplate ............................1 PC Adjusting Nut..........................4 PCS
Backplane Bolt .......................4 PCS
Washer...................................4 PCS
Standoffs................................4 PCS
12
— —
step 3
step 2
4
5
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
Step 1
Step 2
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
Compatible with all mATX boards.
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
IV. Pre-Fill Installation
13
— —
Before installing the water cooling parts for the
graphics card, please remove this part.
14
— —
Upside downHead up
Hard Tube Motherboard
Mounting orientation
(CPU block position)
55x248 Head up All mATX motherboards
55x248 Head up PRO B660M-AMSI
55x248 Head up MAG B660M MORTARMSI
PUMP HEADER
FULL SPEED
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
Step 1
Step 2
When installing the hard pipe from the CPU
block to the water distribution reservoir,
You can move the hard pipe left and right to
get the proper installation length.
Compatible with all ITX boards.
It’s removable
Loosen the screws.
Adjust the slider according to the CPU block position.
Adjust the hard pipe to the same level as the CPU Block inlet.
Before installing the water cooling parts for the
graphics card, please remove this part.
15
— —
16
— —
Upside downHead up
Hard Tube Motherboard
Mounting orientation
(CPU block position)
55x284 Head up All ITX motherboards
BPTA-EFW
It is recommended to install the water-exhaust
fitting at the lowest point of the water cooling
system.
Step 1
Unscrew the top of the water-exhaust fitting.
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
PUMP HEADER
FULL SPEED
AIO_PUMP
CPU_FAN
A Negative electrode -
B positive electrode +
C Speed signal
A B C D
Step 2
Replace with the water-exhaust part. When
screwing in the part, water will start to
discharge, it is recommended to connect
tubing beforehand to control the water outflow.
Pump Spec.
Rated voltage：12V DC
Power consumption：8.4W
Maximum flow：460±15%L/h
Noise：≦24dBA
PWM：Yes
MTBF：≦15,000 hours
Warranty：2 years
Water filling hole
90% full
Before installing the water cooling parts for the
graphics card, please remove this part.
17
— —
V. Filling and Draining
Notice : Do not turn on the pump if the reservoir is empty.
Only Bitspower Coolant, purified water, or distilled water should be
used for the consumer's liquid-cooling fluid. If the consumer choos-
es different liquid-cooling fluids, the resulting impurities may cause
peeling of the coating on some of the hardware, water channel
block-age by built-up residue, improper operation of the water
pump, water tank tube breakage, and O-ring deformation leading to
leakage. Any issues related to the use of inappropriate liquid-cooling
fluid will be the responsibility of the consumer.
In order to make the internal circulation of the liquid-cooling system
cleaner and avoid the pump stuck by the precipitate, we advise you
torinse the liquid-cooling system with distilled water several times
until theexcluded water is clean. Pour the coolant into the reservoir via the water filling
hole. Once the reservoir is 90% full, turn on the power
supply for the pump to run and let the air exit the loop.
Turn off the power supply when the reservoir is near
empty. Repeat until all the air has exited the loop.
BPTA-EFW
It is recommended to install the water-exhaust
fitting at the lowest point of the water cooling
system.
Step 1
Unscrew the top of the water-exhaust fitting.
AIO_PUMP
PUMP HEADER
PWM CONTROL
CPU_FAN
PUMP HEADER
FULL SPEED
AIO_PUMP
CPU_FAN
A Negative electrode -
B positive electrode +
C Speed signal
A B C D
Step 2
Replace with the water-exhaust part. When
screwing in the part, water will start to
discharge, it is recommended to connect
tubing beforehand to control the water outflow.
Pump Spec.
Rated voltage：12V DC
Power consumption：8.4W
Maximum flow：460±15%L/h
Noise：≦24dBA
PWM：Yes
MTBF：≦15,000 hours
Warranty：2 years
Water filling hole
90% full
Before installing the water cooling parts for the
graphics card, please remove this part.
17
— —
V. Filling and Draining
Notice : Do not turn on the pump if the reservoir is empty.
Only Bitspower Coolant, purified water, or distilled water should be
used for the consumer's liquid-cooling fluid. If the consumer choos-
es different liquid-cooling fluids, the resulting impurities may cause
peeling of the coating on some of the hardware, water channel
block-age by built-up residue, improper operation of the water
pump, water tank tube breakage, and O-ring deformation leading to
leakage. Any issues related to the use of inappropriate liquid-cooling
fluid will be the responsibility of the consumer.
In order to make the internal circulation of the liquid-cooling system
cleaner and avoid the pump stuck by the precipitate, we advise you
torinse the liquid-cooling system with distilled water several times
until theexcluded water is clean. Pour the coolant into the reservoir via the water filling
hole. Once the reservoir is 90% full, turn on the power
supply for the pump to run and let the air exit the loop.
Turn off the power supply when the reservoir is near
empty. Repeat until all the air has exited the loop.
Notice
Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage
which may damage the PC components, please perform a 24-hour leaking test with only the pump connected
to the power supply.
Bitspower reserves the right to change the product design and interpretations. These are subject to change
without notice. Product colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product damage due to excessive pressure, the
input pressure should not exceed 0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it will be
borne by the customer. Forbidden to use the leak teser when there is water in the loop or the pump is runing.
Bitspower recommends to use of distilled or pure water or Bitspower Pellucid Coolant as the water-cooling
liquid. Also, the consumer can add Bitspower Dye to Pellucid Coolant for the color requirement. But please do
not add any biocide by yourself. If the consumer chooses different water-cooling liquids, the resulting impurities
may cause peeling off the coating on some of the hardware, water channels blockage by built-up residue,
improper operation of the water pump, water tank tube breakage, and O-rings deformation or loss sealing lead-
ing to leakage. Any issues related to the use of inappropriate water-cooling liquid will be the responsibility of the
consumer.
Do not turn on the pump if the reservoir is empty.
About PSU
Please go to the website or scan the QR CODE to download the manual.
https://www.fsplifestyle.com/en/product/DAGGERPRO850W_GEN5.html
18
— —
— 1 —
TITAN ONE MINI_3.0 Guía de instalación
BPTA-O11D-MINI_A3.0-BK
Spanish
B-1 B-2
A-1
A-2
A-3
248
55
A
B
C
Tubos rígidos
C-1
Tubo de drenaje
C-2
V3
:16
284
55
:16
La variación permitida en la longitud del tubo es de ±2 mm
Para placa base MATX estándar (24 × 24 cm).
Para placa base ITX o placa base MATX de tamaño no estándar.
Consulte las tablas de las páginas 5 y 16
para conocer la compatibilidad de los tubos
rígidos y la placa base.
Lista de componentes
...1 piezas
Soporte de montaje Intel
Bloque de refrigeración líquida para CPU
A
......1 piezas
BPTA-CPUMS-V2-SKA
A-1
A-2
...........1 set
Conjunto de placa base
A-3
Equipamiento
B
............2 piezas
BPTA-DOTFH1622
B-1
.................2 piezas
BPTA-15ATFH16
B-2
Accesorio
C
......................4 piezas
Tubos rígidos
C-1
.................1 piezas
Tubo de drenaje
C-2
Juego de bloques para CPU
C-3
BP-CPUPDB-AMD5MS
C-5
Tornillo de mariposa
MUELLE
Tuerca de mariposa
Separador de 1 mm
Tornillo M3 × 32 mm
SC6-32M3
Arandela de copa de nailon
..............4 pcs
..4 pcs
.............................4 pcs
..............4 pcs
..............8 pcs
..............4 pcs
...............................4 pcs
BPTA-MKCPUMS-1700 or
BPTA-MKCPUMS-1700-V2
C-4
Bitspower se reserva el derecho de modificar el diseño y las interpretaciones
del producto. Estos están sujetos a cambios sin previo aviso. Los colores del
producto y los accesorios se basan en el producto real.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
