ekwb EK-Classic Kit P240 D-RGB Installation guide

INSTALLATION MANUAL

Liquid Cooling Starter Kit

Classic D-RGB S240 S360 P240 P360

EK-Classic Kit Series Units | 2nd Revision, June 24th 2020

/ 1 /

We are EK® - the leader in computer liquid cooling solutions. Our

company emerged in 2003, bearing the name of its founder Edvard

König. Over the years, we expanded our product portfolio to become

the most comprehensive provider of liquid cooling products and

engineering solutions, marketed under the EK brand.

EK gained a strong reputation among computer enthusiasts seeing

as we helped them transform ordinary computers into extraordinary

machines. Our products are recognized for elegant design, attention

to detail, operational effectiveness, and outside-the-box approach.

Today, EK products are available worldwide, and the company holds

several partnerships with some of the most recognized brands. Our

vision is to lead the way in making computers better.

Safety Precautions

1. Keep and store the product away from the reach of children.

2. Check the component list and condition of the product

before installation. If there is any problem, contact the shop

where you have purchased the product to get a replacement

or refund.

3. EKWB d.o.o. is not responsible for any damages due to

external causes, including but not limited to improper use,

problems with electrical power, accident, neglect, alteration,

repair, improper installation, improper testing.

4. CPU and motherboard are subject to damage if the product is

incorrectly installed.

5. This product is a CPU liquid cooling solution kit, comprising of

individual original EK parts. Combining this liquid cooling unit

with parts other than EK products, may lead to warranty loss.

6. The product warranty period is 24 months.

QUICK INSTALLATION GUIDE

/ 2 /

RADIATOR SPACE CONSTRAINT REQUIREMENTS 5

INSTALLATION TIPS FOR NOVICES 6

LIQUID COOLING SYSTEM 6

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY 7

INSTALLING THE WATER BLOCK 8

ENCLOSED IN THE BOX 8

LGA20113 SOCKET MOTHERBOARDS 9

LGA 115X/1200 SOCKET MOTHERBOARDS 11

AMD® SOCKET MOTHERBOARDS 15

INSTALLING THE RADIATOR AND FANS 19

METHOD 1 19

METHOD 2 INSTALLING THE RADIATOR AND FANS IN ONE GO 20

INSTALLING THE PUMP-RESERVOIR UNIT 22

ENCLOSED IN THE PACKAGING 22

INSTALLING THE PUMPRESERVOIR UNIT TO THE BOTTOM OF THE CASE

23

CONNECTING THE TUBING 25

CONNECTING THE PUMPRESERVOIR UNIT 27

ELECTRICAL CONNECTIONS 27

RECOMMENDED FILLING AND LEAKTESTING PROCEDURE 28

CONNECTING THE FANS, PUMP, AND CPU DRGB LIGHTS 29

FILLING THE SYSTEM FOR THE FIRST TIME 30

DRAINING THE LOOP 32

SYSTEM EXPANSION POSSIBILITIES 33

MAINTENANCE 34

FREQUENTLY ASKED QUESTIONS 35

TROUBLESHOOTING 36

THE CPU IS OVERHEATING 36

THE COOLER IS TOO LOUD 37

CLEANING GUIDE 38

PREVENTIVE STEPS 38

SUPPORT AND SERVICE 42

SOCIAL MEDIA 42

SCOPE OF DELIVERY 3

REQUIRED TOOLS 4

TABLE OF CONTENTS

/ 3 /

SCOPE OF DELIVERY

AMD Mounting Kit

Classic (1x)

D-RGB Splitter Cable (1x) Angled Fitting (2x) Soft Tube Cutter (1x)

Radiator With Screws Coolant – Concentrate

100mL

Tube ATX Bridging Plug

CPU Water Block

With Accessories

Compression Fittings

Pump-Reservoir Combo

With Accessories

D-RGB Fans

/ 4 /

REQUIRED TOOLS

Pair of Scissors

1L Bottle of Distilled Water

H20

Fan Cable Y-Splitter Installation Manual

Phillips Head Screwdriver Mixing Bottle

EK-RES X3 Holder (1x) Multi Allen Key (1x) Filling Bottle 500ml (1x) Pump Cable Extension

500mm (1x)

UNI Bracket Cable Pump Testing

Adapter (1x)

/ 5 /

RADIATOR SPACE CONSTRAINT REQUIREMENTS

400 mm (15,75 in)

280 mm (11,02 in)

130 mm (5,12 in)

130 mm (5,12 in) 46 mm (1,8 in) 28 mm (1,10 in)

400 mm (15,75 in)

280 mm (11,02 in)

130 mm (5,12 in)

46 mm (1,8 in) 28 mm (1,10 in)

P240 P360 S240 S360

/ 6 /

INSTALLATION TIPS FOR NOVICES

1. To lower the shipping cost, we have decided to enclose the

coolant concentrate only. Therefore, you need to provide 1

liter (1L) of distilled water. You can ﬁnd it at every gas station or

supermarket.

2. Never run this system on tap water and always use the

enclosed cooling concentrate in the right ratio.

3. Never use alcohol, alcohol derivatives, or alcohol-based

solvents in the system. Using alcohol might result in permanent

damage to water cooling KIT components, especially acrylic

parts of the system.

4. It is best practice to do a proper 24-hour leak test before using

your computer.

5. If you spot any leaks, turn the power off immediately.

6. Optimize tube length to prevent excessive bending and kinking

of the tubing.

7. Never let your pump run dry. If this is happening for a

prolonged period, you risk destroying the water pump’s bearing,

ultimately rendering the pump useless.

8. You are encouraged to periodically clean the radiator assembly

as it will collect dust over time. It’s best to be done with a soft

wide-tip brush and a vacuum cleaner. See chapter Universal

Cleaning Guide.

LIQUID COOLING SYSTEM

CPU Water Block

Radiator With Fans

COLD AIR

HOT AIR

Reservoir-Water Pump

Combo

/ 7 /

GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY

This CPU liquid cooling unit is pre-assembled for use with modern

Intel desktop-socket type motherboards. By default (out of the box)

this water block supports the following CPU sockets:

- Intel® Socket LGA-115x / LGA-1200

- Intel® Socket LGA-2066/LGA-2011(-3)

- AMD® Socket AM4*

*requires replacing the Intel® mounting plate with an AMD® one.

This product is also fully compatible with AMD® AMx/FMx

sockets but requires a user to replace factory installed Intel

mounting plate with an AMD® one. The following sockets

are then compatible:

- AMD® Socket AMx

- AMD® Socket FMx

The AMD Mounting kit with a mounting plate is already enclosed

inside this Kit!

/ 8 /

INSTALLING THE WATER BLOCK

CPU Water Block Thermal Grease Steel Backplate - LGA 115x

Rubber Backplate Distancer - LGA 115x

CPU WATER BLOCK WITH ACCESSORIES

MOUNTING KIT FOR INTEL® SOCKET MOTHERBOARDS

Thumb Nut

Mounting Screw - LGA 115x

Mounting Screws - LGA 20xx

Mounting Springs - Intel® Washers M4 x 0.8 mm

ENCLOSED IN THE BOX

MOUNTING KIT FOR AMD® SOCKET MOTHERBOARDS

/ 9 /

STEP 2

Cleaning the CPU: Wipe the CPU’s contact surface with a

nonabrasive cloth or Q-tip (as shown in the image).

Applying Thermal Compound: On the clean CPU IHS - Integrated

Heat Spreader, apply a blob or line of enclosed thermal compound

(see sample image on the left).

EK recommends the quantity of about two rice grains of

thermal compound. There is no need to cover the whole

IHS. Applying too much thermal grease will disrupt

cooling performance!

LGA20113 SOCKET MOTHERBOARDS

STEP 1

Prepare the foil bag with the mounting mechanism that is enclosed

with the CPU water block.

Install four (4) speciﬁc LGA 2011 M3 thumb screws into four threaded

stubs on the LGA 2011 socket’s integrated latch mechanism (ILM).

The screws are to be installed using no tools (i.e., pliers).

It is recommended to remove the motherboard from the

chassis before proceeding with the CPU water block

installation due to space constraints in various PC cases.

Nonabrasive

Cloth

IHS

LGA-2011 M3

Thumb Screw

LGA-2011 M3

Thumb Screw

STEP 1

STEP 2

/ 10 /

STEP 3

Remove the sticker from the water block cold plate.

Align the water block over the mounting screws on the LGA 2011(-3)

motherboard with a pre-installed CPU.

Before proceeding with installation, it is mandatory to remove

the protective foil from the backside of the water block.

Place an enclosed compression spring and a thumb nut over

each M3 thumb screw. Start fastening two thumb nuts at a time,

preferably in a cross pattern, but do not tighten them fully until all

four are partially screwed in. Then - using your ﬁngers only - screw

in all four thumb nuts until you reach the end of the thread.

Thumb Nut

Coiled Spring

Fitting Ring

Fitting Barb

Inlet Port

Outlet Port

STEP 4

Tighten the ﬁtting barbs in a clockwise direction until the gasket

underneath is compressed.

The installation of the CPU water block is now complete.

With EK-Supremacy Classic series water blocks, it is

mandatory to use the port closest to the center of the water

block as the INLET port. Mixing these ports up may result in

poor thermal performance of the water block.

STEP 3

STEP 4

/ 11 /

LGA 115X/1200 SOCKET MOTHERBOARDS

STEP 1

If already installed, please remove the motherboard from the computer

case. Place it on an even surface with the front facing downward.

STEP 1

STEP 2

Preparing the Backplate Rubber Gasket

The enclosed rubber gasket is an essential part of the backplate and

mounting system, and therefore must be used every time you install

this water block on the motherboard.

/ 12 /

M3 Thumb

Screw

PVC Washer

STEP 4

Install four (4) M3 thumb screws into your motherboard. It is mandatory

to put a plastic washer underneath each M3 thumb screw. Tighten the

screws to the metal backplate until you reach the end of the thread.

Using tools (i.e., pliers) is not recommended.

LGA-115x M3

Thumb Screw

Rubber

gasket

Motherboard

Metal

Backplate

STEP 3

Install the backplate rubber gasket and place the metal backplate

for Intel® LGA 115x/1200 socket to the back of your motherboard

ribbed side up (facing away from the motherboard). Align the holes

on the motherboard with holes on the rubber gasket and backplate.

Make sure to orientate the rubber gasket to ﬁt past the

CPU socket ILM backplate. On certain ITX form factor

motherboards, the rubber gasket may need to be trimmed

with household scissors.

Using one hand, carefully rotate the motherboard assembly with the

front side facing up while holding the backplate and rubber gasket in

place with the other hand.

/ 13 /

STEP 6

Align the water block over the mounting screws on the LGA

115x/1200 motherboard with a pre-installed CPU.

Before proceeding with installation, it is mandatory to remove

the protective foil from the backside of the water block.

Place an enclosed coiled spring and a thumb nut over each M4

thumb screw. Start fastening two thumb nuts at a time, preferably in

a cross pattern, but don’t tighten them fully until all four are partially

screwed in. Then – using your ﬁngers only – screw in all four thumb

nuts until you reach the end of the thread.

Thumb Nut

Coiled Spring

STEP 6

STEP 5

Cleaning the CPU: Wipe the CPU’s contact surface with a

nonabrasive cloth or Q-tip.

Applying Thermal Compound: On the clean CPU IHS, apply a blob

or line of enclosed thermal compound (see sample image).

EK recommends the quantity of about two rice grains of

thermal compound. There is no need to cover the whole

IHS. Applying too much thermal grease will disrupt

cooling performance!

Nonabrasive

Cloth

IHS

STEP 5

/ 14 /

STEP 8

Install the motherboard back into the computer case.

The installation of the CPU water block is now complete.

STEP 8

STEP 7

With EK-Supremacy Classic series water blocks, it is

mandatory to use the port closest to the center of the water

block as the INLET port. Mixing these ports up may result in

poor thermal performance of the water block.

Tighten the ﬁtting barbs in the clockwise direction until the gasket

underneath is compressed.

Fitting Barb

Fitting Ring

Outlet Port

Inlet Port

STEP 7

/ 15 /

STEP 1

STEP 2

Intel® Socket

Mounting Plate

AMD® Socket

Mounting Plate

M4x14

Screws

Copper Base

Orientation

STEP 2

Replace the factory-installed Intel® mounting plate with the AMD®

one. You will feel the mounting plate locking into position when

placed correctly onto the top.

Reseat the O-ring gasket into the gap between the mounting plate

and water block top.

Pay special attention to the orientation of the copper base.

It should be placed as shown in the picture.

Reinstall the M4x14 screws and use the 2.5mm Allen key in the

clockwise direction to screw them in.

AMD® SOCKET MOTHERBOARDS

STEP 1

Replacing the Mounting Plate

Place the water block on an even surface and, using the 2.5mm Allen

key in the counter-clockwise direction, remove four M4x14 DIN 7991

screws attaching the copper base to the top.

/ 16 /

STEP 3

If already installed, please remove the motherboard from the computer

case. Place it on an even surface with the front facing downward.

STEP 4

Removing the Original Hold-Down Clamps

Using a Philips head screwdriver, remove the four UNC 6-32 screws

securing the original plastic hold-down clamps around the socket

(as shown in the picture). You can use the factory backplate for

mounting the EK-Supremacy Classic water block.

AMD® Factory

Backplate

UNC 6-32

Screws

Hold-Down

Clamps

STEP 3

STEP 4

/ 17 /

STEP 5

Cleaning the CPU: Wipe the CPU’s contact surface with a

nonabrasive cloth or Q-tip (as shown in the image).

Applying thermal compound: EK recommends a blob or line

method for applying the enclosed thermal compound to the CPU heat

spreader (see sample image).

The quantity of about two rice grains of thermal

compound is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will

disrupt cooling performance!

STEP 6

Align the water block with the pre-installed mounting screws on the

AMD® socket motherboard.

Before proceeding with installation, it is mandatory to remove

the protective foil from the backside of the water block.

Start fastening two thumb screws at a time, preferably in a cross

pattern, but don’t tighten them fully until all four are partially screwed

in. Then – using your ﬁngers only – screw in all four thumb screws

until you reach the end of the thread.

Thumb Screw

Coiled Spring

Nonabrasive

Cloth

IHS

STEP 6

STEP 5

/ 18 /

STEP 7

With EK-Supremacy Classic series water blocks it is

mandatory to use the port that is nearest to the center of

the water block as INLET port. Mixing the ports may result in

poor thermal performance of the water block.

Tighten the ﬁtting barbs in the clockwise direction until the gasket

underneath is compressed.

STEP 8

Install the motherboard back into the computer case.

The installation of the CPU water block is now complete.

Fitting Ring

Fitting Barb

Inlet Port

Outlet Port

STEP 7

STEP 8

Page is loading ...

ekwb EK-Classic Kit P240 D-RGB Installation guide

ekwb EK-Classic Kit P240 D-RGB Installation guide

Related papers

Other documents