Apex Digital AD-600A User manual

Apex Digital
Brand
Apex Digital
Model
AD-600A
Category
CD players
Type
User manual
1
APEX DIGITAL
AD-600A
Safety Precautions
The lightning flash with a arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE, DUE TO THE HIGH RISK OF FIRE OR
ELECTRIC SHOCK. DO NOT OPEN THE CABINET DANGEROUS HIGH VOLTAGES ARE PRESENT
INSIDE THE ENCLOSURE. ONLY QUALIFIED SERVICE PERSONNEL SHOULD ATTEMPT THIS.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, AND
FULLY INSERT.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOUD.
CAUTION: This Digital Video Disc Player employs a Laser System. To prevent direct exposure to the laser beam, do
not try to open the enclosure. Visible laser radiation when open and interlocks defeated.
The use of control adjustments or the performance of procedures other than those specified may result in
hazardous radiation exposure.
DO NOT STARE INTO BEAM.
To ensure proper use of this product, please read this owner’s manual carefully and retain for future
reference.Should the unit require maintenance, contact an authorized service location, or contact APEX
Digital Inc.Only qualified service personnel should remove the cover.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant
with the FCC Rules, Part 15. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
WARNING: Changes or modifications made to this equipment, not expressly approved by APEX or parties authorized by
APEX will void all the manufacture warranties.
THE REGION CODE FOR THE UNIT IS 1.
Since it is very usual for DVD movies to be released at different times in different regions of the world, all
players have region codes and disks can have an optional region code. If you load a disk of a different
region code to your player, you will see the region code notice on the screen. The disk will not play, and
should be unloaded.
For Customer Use:
In spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.
Model No. Serial No.
Retain this information for future reference.
CLASS 1
LASER PRODUCT
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
WARNING:TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PART INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
!
2
APEX DIGITAL
AD-600A
Important Safety Instructions
1. READ THE OWNER’S MANUAL - Follow all the operating
and installation instructions.
2. R
ETAIN INSTRUCTIONS - The safety and operating
instructions should be retained for future use.
3. P
AY ATTENTION TO WARNINGS - All warnings on the
appliances and in the operating instructions should
be followed.
4. F
OLLOW INSTRUCTIONS - Follow all operating instructions
to achieve optimal use.
5. P
OWER SOURCES - This product should only be
operated from the type of power source indicated on
the label.
6. H
EAT - This unit should be situated away from heat
sources, such as amplifiers, radiators, stoves or any
other units producing heat.
7.W
ATER AND MOISTURE - Do not use this unit near water,
for example: near the kitchen sink, a bath tub, washbowl,
laundry tub, swimming pool, or in a wet basement.
8. C
LEANING - Unplug the unit from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners
directly on the unit. Use a damp cloth for cleaning.
9. CARTS AND STANDS - The unit and cart combination
should be moved with care. Quick stops, excessive force
and uneven surfaces may cause the unit and cart
combination to overturn. The unit should be used only
with a cart or stand recommended by the manufacturer.
10. P
OWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be walked
on or pinched by items places upon or against them.
11. O
VERLOADING - Do not overload wall outlet, or
extension cords. This can result in a risk of fire or
electrical shock.
12. D
ISC TRAY - Keep your fingers well clear of the disc
tray as it is closing. It may cause serious personal injury,
or do damage to the machine.
13. W
EIGHT - Do not place a heavy object (amplifier,
receiver) on your DVD player. The object may fall,
causing serious personal injury or death.
14. O
BJECT AND LIQUID ENTRY - Care should be taken so
that objects do not fall and liquids are not spilled into the
units openings. Such situations could result in fire or
electrical shock.
15. N
ON-USE PERIODS - The power cord of the unit should
be unplugged, when not in use for a long time.
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S
MANUAL AND THOSE MARKED ON THE UNIT. PLEASE KEEP THIS MANUAL FOR FUTURE USE.
This product was designed and manufactured to meet strict quality and safety standards. The safeguards incorporated
in this unit will protect you if you observe the following procedures for installation, use, and service. There are, however,
some installation and operation precautions which you should be aware of.
3
APEX DIGITAL
AD-600A
Important Safety Instructions
16. DISC - Do not use a deformed, cracked, or heavily
scratched disc. Using these disc will limit your viewing
pleasure, and/or may damage the internal workings of
your machine.
17. L
IGHTING AND POWER SURGES - Use a power strip to
help eliminate surges and spikes caused by lighting and
static electric charges.
18. P
OLARIZATION OR GROUNDING - Precautions should be
taken so that the polarization or grounding means of a
unit is not defeated. To prevent electric shock match the
wide blade of the plug to the wide slot of the outlet and
fully insert. If the wide blade does not match up with the
outlet try reversing the plug.
19. S
ERVICING - Do not attempt to service this unit
yourself. Only qualified APEX service technicians should
work on your DVD Player.
20. D
AMAGE REQUIRING SERVICE - The unit should be
serviced by qualified APEX authorized specialist when:
A. The unit does not appear to operate normally or
exhibits a marked change in performance.
B. When the power supply cord or plug is damaged.
C. If objects have fallen, or liquid has been spilled
into the unit.
D. If the unit has been exposed to water or rain.
E. If the unit has been dropped or damaged in
any way.
21. SAFETY CHECK - Ask the service technician to perform
safety checks upon completion of the unit.
22. W
ALL AND CEILING MOUNTING - The unit should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
Continued
4
APEX DIGITAL
AD-600A
Introduction
Your DVD video player is a player for digital video discs
conforming to the universal DVD video standard. With it, you
will be able to enjoy full-length movies with true cinema picture
quality, and stereo or multichannel sound (depending on the
disc, and on your playback setup). The unique features of this
DVD video, such as selection of sound track and subtitle
languages, and of different camera angles (again depending on
the disc), are all included. What’s more, Parental Control lets
you decide which discs your children will be able to see.
You will find your player remarkably easy to use, by way of the
On-Screen Display (setup menu) and player display, in
combination with the remote control.
MP3
Recordable
KARAOKE
UNPACKING
When shipping the DVD video player, the original shipping carton and packing comes in handy. For
maximum protection, repack the unit as it was originally packed at the factory.
First check and identify the contents of your DVD video player package, as listed below:
- DVD video player
- Remote control handset with separately packed batteries
- Power cable
- S-Video cable (1)
- RCA cables (3) (1 yellow, 1 red, and 1 white)
- Owner’s manual
- Size AAA batteries (2)
If any item should be damaged or missing, please inform your supplier without delay.
Keep the packaging materials, you may need them to transport your player in the future.
WHERE TO LOCATE YOUR DVD
A. Place the unit on a firm, flat surface.
B. When you place this DVD video player near a radio, or VCR, the playback picture may become poor
and/or distorted. In this situation, move the DVD video player away from the other units.
C. Keep away from direct sunlight & domestic heating equipment.
D. If placed in a cabinet, please allow at least 2.5 cm (1 inch) of free space all around the player for
proper ventilation.
TO OBTAIN A CLEAR PICTURE
The DVD video player is a high technology, precision device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the
operating environment. For details, contact your nearest dealer.
5
APEX DIGITAL
AD-600A
Table of Contents
Safety Precautions ........................... 1
Important Safety Instructions ........... 2 - 3
Introduction ........................................ 4
Identification of Controls .................... 6
DVD Display..........................................7
Remote Control.................................. 8 - 9
Connecting to a TV ............................ 10
Connecting to an Audio System or TV
Component Video Input ..................... 11
Connecting to a TV using a RF Modulator
..............................................................12 - 13
Connecting to Optional Equipment .... 14 - 15
What is MP3 and VCD ?.......................16-17
Playing Back a Disc ........................... 18 - 20
Locating a Specific Title,
Chapter or Track ................................ 21 - 22
Playing Repeatedly ........................... 23
Playing in Random Order................... 24
Zooming a Picture ............................. 25
Selecting the Camera Angle/
Selecting a Language ........................ 26
Playing in a Favorite Order.................. 27
Selecting Subtitles ............................. 28
Karaoke ............................................. 29 - 30
Using the On-screen Display ............ 31
Setting the Parental Lock................... 32
Customizing the Function Settings .... 33
Notes on Discs................................... 34
Specifications..................................... 35
Before Calling Service Personnel ...... 36
Memo ................................................ 37
Limited Warranty................................. 38
6
APEX DIGITAL
AD-600A
Identification of Controls
FRONT PANEL
REAR PANEL
1 4 5 6
8
9
10
113
12
7
3
2
1POWER ON/OFF
2 MIC 1
3 MIC 2
4MIC LEVEL 1
5MIC LEVEL 2
6DVD DISPLAY
7DISC LOADING TRAY
8 OPEN/CLOSE
9STOP
10 PLAY
11 PAUSE
12 SKIP REVERSE
13 SKIP FORWARD
1 COMPONENT VIDEO OUTPUT
2S-VIDEO OUTPUT
3 COMPOSITE VIDEO OUTPUT
4 ANALOG AUDIO OUTPUT 2
5 ANALOG AUDIO OUTPUT 1
6 DIGITAL AUDIO-COAXIAL OUTPUT
7POWER CORD INPUT
1
4
5 6
7
3
2
7
APEX DIGITAL
AD-600A
DVD Display
VIDEO CD/AUDIO CD indicator
Operating status indicator
Title number
Chapter/track number indicator
DVD indicator
Repeat playback mode indicator
MEMORY indicator
PBC indicator
Angle icon indicator
Component video indicator
RANDOM indicator
The indicators vary depending on the kinds of discs you play.
DVD Video discs
• When closing the disc tray:
Example
• During playback:
Example
Some DVD video discs may not display
the chapter numbers or elapsed time.
TITLE
3
DVD
0:00:02
Playing chapter 3
Elapsed time of
the current title
VCD Video discs
• When closing the disc tray:
Example
• During playback:
Example
TRK VCD
3
0:08:88
Playing track 3
Elapsed time of
the current title
Compact Disc
• When closing the disc tray:
Example
• During playback:
Example
TRK CD
3
0:00:02
Playing track 3
Elapsed time of
the current title
MP3 discs
• When closing the disc tray:
Example
• During playback:
Example
TRK
3
0:00:02
Playing track 3
Elapsed time of
the current title
CH/
1:0
PBC
1:0
• Other indicators
When playing back the
same title, chapter or
track repeatedly.
When playback is paused.
When component video
is set.
When playing back a
specific segment
repeatedly. (A-B repeat)
During memory playback.
During shuffle playback.
When playing back the entire
disc repeatedly.
When the camera angle can
be changed.
• Display directions
OPEN
INITIAL
TITLE
CLOSE
STOP
ROOT
Total playing time indicator
8
APEX DIGITAL
AD-600A
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
17
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
36
38
37
35
20. PBC OFF
(PLAYBACK CONTROL)
21. ANGLE
22. SUBTITLE
23. GOTO
24. DISPLAY
25. MUTE
26. CLEAR
27. ECHO+
(KARAOKE)
28. KEY+
(KARAOKE)
29. VOLUME
30. ECHO-
(KARAOKE)
31. KEY-
(KARAOKE)
32. ENTER/PLAY
33. RESUME
34. STEP
35. ZOOM
36. FORWARD SKIP
37. PREVIOUS SKIP
38. PAUSE/PLAY
Remote Control
1. POWER
2. SETUP
3. PAL/NTSC (SWITCH)
4. AUDIO
5. NUMBERS
6. SHUFFLE
7. PROGRAM
8. VOCAL ASSIST
(KARAOKE/VCD)
9. SURROUND
(KARAOKE)
10. DIRECTION
(UP/ DOWN/LEFT/RIGHT)
11. SLOW
12. REPEAT
13. A-B REPEAT
14. REVERSE
15. FORWARD
16. STOP/RETURN
17. OPEN/CLOSE
18. DVD DIGEST
19. TITLE
THE INSTRUCTIONS IN THIS MANUAL DESCRIBE
THE FUNCTIONS ON THE REMOTE CONTROL.
9
APEX DIGITAL
AD-600A
Remote Control
Continued
1 2 3
Open the cover.
OPERATING WITH THE REMOTE CONTROL
Operating DVD video player with the remote control.
1
The remote control must point at the remote sensor, in order for the
DVD player to function correctly.
Distance: Maximum of 7 m from the front of the remote sensor.
Angle: Approximately 30˚ from each direction.
*Please do not place the remote sensor towards any light source such as direct
sunlight or illumination. The DVD video player will malfunction, if you do so.
Insert batteries (AAA size).
Make sure to match the + and - on
the batteries to the marks inside the
battery compartment.
Close the cover.
NOTICE (BATTERIES)
PREPARING THE REMOTE CONTROL
To operate the DVD video player, you must first place the batteries in the remote control.
FOLLOW INSTRUCTIONS BELOW BECAUSE INCORRECT USE OF BATTERIES MIGHT CAUSE THEM TO LEAK OR CORRODE.
• Do not place the batteries in the wrong direction.
• It is dangerous to charge/heat/open or short-circuit the batteries.
• Do not leave dead batteries or mix old/new batteries in the remote control.
• When not using the remote control for a long duration of time, remove the batteries.
• When difficulties occur, with the remote control, or if the operating range becomes reduced, then replace the batteries.
• If leakage from the battery occurs, wipe the battery liquid from the battery compartment, then replace the batteries.
• With normal usage the batteries should last one year.
NOTICE (REMOTE CONTROL)
• The remote control should be aimed directly towards the remote sensor of the DVD video player.
• Avoid dropping the remote control.
• Avoid spilling any liquids and/or extreme heat.
10
APEX DIGITAL
AD-600A
Connecting to a TV
NOTICE
• It will be helpful to also refer to the manual of the connected TV.
• Turn off the power and unplug both units before setting up any connections.
• The playback picture will be distorted, if you do not connect the DVD video player directly to your TV because DVD video discs
are protected by Macrovision.
• Therefore, if you connect the DVD video player to a video cassette recorder (VCR), or TV/VCR combination, the playback picture
will be distorted.
GOOD, BETTER, BEST
Connecting the DVD video player to your TV.
• How to setup the sound output
From the SETUP MENU, set the “AUDIO OUTPUT” to “ANALOG”.
• How to setup the video output
From the SETUP MENU, set the “SET VIDEO OUT” to “S-VIDEO” when using the S VIDEO OUT jack.
GOOD
Red
White
Yellow
Red White
Yellow
BETTER
Red
White
Black
Red
White
Connect the DVD video player with the S Video cable, if the
TV has an S video input. Do not connect the yellow video
cable if using the S Video cable.
Black
TV Audio Input
TV Video Input
11
APEX DIGITAL
AD-600A
BEST PICTURE
The Component Video input allows you to enjoy the sound and picture quality of the DVD video discs.
• How to setup the sound output
From the SETUP MENU, set the "AUDIO OUTPUT" To "ANALOG".
• How to setup the video output
From the SETUP MENU, set the "SET VIDEO OUT" to "YUV VIDEO" when using the Component Video
output jacks.
Connecting to an Audio System or TV Component Video Input
White
Red
To Cb VIDEO IN
To Y VIDEO IN
To Cr VIDEO IN
NOTICE
• It will be helpful to also refer to the manual of the connected TV.
• Turn off the power and unplug both units before setting up any connections.
• Keep the DVD video player away from any tuner or radio to avoid any static or distorted sound during a broadcast.
• When connecting any disconnecting the DVD video player, be sure to turn off the amplifier to avoid any speaker damage.
• Due to the wide dynamic range of sound output of the DVD video player, adjust the volume of your receiver to a comfortably modist
listening level to avoid any speaker damage.
NOTICE (COMPONENT VIDEO OUTPUT)
Component input terminals when connected to selected TV's and monitors will produce a higher quality picture playback. Depending
on the selected TV's and monitors, the wording of the component input terminals may vary. (ie:R-Y, Y, B-Y, etc.) If there are any
fluctuations with the color played back adjust the TV or monitor to achieve the best audio and/or picture.
To Y
VIDEO
OUT
To Cr
VIDEO
OUT
To Cb
VIDEO
OUT
White
Red
Audio
12
APEX DIGITAL
AD-600A
RF-Modulator
Your TV (Back)
VTo TV AntennaRL
UHF/Antenna IN
Coaxial
Your VCR (Back)
UHF/Antenna OUT
Coaxial
COAXIAL
VIDEO OUT
AUDIO OUT
L
R2
1
DVD (Back)
TV / Video Input
Conntection
TV /Audio Input
Conntection
(R)
(R)
(L)
(L)
(V)
(V)
Connection 1
Figure 1
Connecting the TV to the DVD through the
VCR
Note: Many VCRs will distort the picture of a DVD
player. This is NOT a malfunction of the DVD player
or VCR. All DVD manufacturers are required to
install macrovision copyright ciruritry to prevent
copying via VCR.This is what causes the distortion.
1) Connect the three-terminal composite video
cable to the back of your Apex DVD player.This
cable has three prongs, one each in yellow, red,
and white.The yellow prong will go into the jack
labeled "Video Out"; the white prong will go into the
jack labeled "Front-L"; the
red prong will go into the jack labeled
"Front-R".
2) Connect the opposite end of the composite-video
cable into the back of the RF modulator. Make sure
to match up the colors correctly.
3) Connect a coaxial cable from the "Antenna Out"
jack on the back of your VCR to the "Antenna" jack
on the RF modulator.The coaxial cable is the one-
wire, metal-ended type that you screw onto the
VCR.
4) Connect a coaxial cable from the "To TV" jack on
the RF modulator to the jack on the back of your
TV.
Many older televisions do not have the newer component-video, composite-video, or s-video connections that
optimize DVD technology. While it would be advised to purchase a newer television in order to take full advantage of
the digital quality of DVD’s, it is possible to connect an older television to a DVD player.This connection requires a
device called an RF modulator.
First, it is necessary to ascertain whether or not your TV needs a RF modulator. Look at the back of your TV. If you
see three input connectors lined up in a row, in the colors of yellow, red, and white, then you will not need an RF
modulator. If you see a connector labeled "s-video", then you will not need an RF modulator. If you do not have either
of these connectors, then you will need to purchase an RF modulator from the store where you purchased your Apex
Digital DVD player or other home electronics retailers.
Older televisions use a coaxial connection, which combines all of the video signal from an exterior source into a
single line.This line is then translated by your TV into the picture you see. The RF modulator combines the output
signals from the DVD player, or any other device, into the coaxial connection for use by your television.
Below are written and pictoral instructions on the proper way to connect an RF modulator to your Apex DVD player
and your TV.
Note: Not all RF Modulators are compatible
with APEX Digital players. Please see our
website for recommendations.
5) Make sure your TV is set to the appropriate
channel before using your DVD player. In most cases,
this is channel 3 or 4.
Connecting to a TV using a RF Modulator
13
APEX DIGITAL
AD-600A
COAXI AL
VIDEO OUT
AUDIO OUT
L
R2
1
RF-Modulator
Your TV (Back)
(Back)
TV / Video Input
Conntection
TV /Audio Input
Conntection
VTo TV AntennaRL
(R)
(R)
(L)
(L)
(V)
To your Cable/Satelite connection
(V)
UHF/Antenna IN
Coaxial
Your Cable/Satelite Box
INOUT
IN
OUT
Your VCR (Back)
UHF/Antenna OUT
Coaxial
Figure 3
Connection 3
Connecting the TV , DVD,VCR, and Cable
or Satelite Box
1) Connect the three-terminal composite video
cable to the back of your Apex DVD player.This
cable has three prongs, one each in yellow, red,
and white.The yellow prong will go into the jack
labeled "Video Out"; the white prong will go into
the jack labeled "Front-L"; the red prong will go
into the jack labeled "Front-R".
2) Connect the opposite end of the composite-
video cable into the back of the RF modulator.
Make sure to match up the colors correctly.
3) Connect a coaxial cable from the "Antenna
Out" jack on the back of your cable or satellite
receiver to the "Antenna In" jack on the back of
your VCR. The coaxial cable is the one-wire,
metal-ended type that you screw onto the VCR.
4) Connect a coaxial cable from the "Antenna
Out" jack on the back of your VCR to the
"Antenna" jack on the RF modulator.
5) Connect a coaxial cable from the "To TV" jack
RF-Modulator
Your TV (Back)
VTo TV AntennaRL
To your Cable/Satelite connection
UHF/Antenna IN
Coaxial
Your Cable/Satelite Box
INOUT
COAXI AL
VIDEO OUT
AUDIO OUT
L
R2
1
DVD (Back)
TV / Video Input
Conntection
TV /Audio Input
Conntection
(R)
(R)
(L)
(L)
(V)
(V)
Figure 2
Connection 2
Connecting the TV to the DVD through the
Cable or Satelite Box
1) Connect the three-terminal composite video
cable to the back of your Apex DVD player.This
cable has three prongs, one each in yellow, red,
and white.The yellow prong will go into the jack
labeled "Video Out"; the white prong will go into
the jack labeled "Front-L"; the red prong will go
into the jack labeled "Front-R".
2) Connect the opposite end of the composite-
video cable into the back of the RF modulator.
Make sure to match up the colors correctly.
3) Connect a coaxial cable from the "Antenna
Out" jack on the back of your Cable or Satellite
receiver to the "Antenna" jack on the RF
modulator.The coaxial cable is the one-wire,
metal-ended type that you screw onto the VCR.
4) Connect a coaxial cable from the "To TV" jack on the RF modulator
to the jack on the back of your TV.
5) Make sure your TV is set to the appropriate channel before using
your DVD player. In most cases, this is channel 3 or 4.
on the RF modulator to the jack on
the back of your TV.
6) Make sure your TV is set to the
appropriate channel before using
your DVD player. In most cases, this
is channel 3 or 4. Also make sure
that the VCR is set to the
appropriate channel, as well.This
selector is usually on the back of
your VCR. Consult your VCR
manual for further information.
Connecting to a TV using a RF Modulator
Continued
14
APEX DIGITAL
AD-600A
NOTICE
• Do not connect the PCM/DOLBY DIGITAL AUDIO OUT jack of the DVD video player to the AC-3 RF input of a Dolby Digital receiver.
Instead, connect to the “DIGITAL” or “COAXIAL” input of a Dolby Digital/DTS receiver or Processor. The input of the A/V receiver is
not compatible with the PCM/DOLBY DIGITAL AUDIO OUT jack and is primarily for Laserdiscs only.
• Connect the PCM/DOLBY DIGITAL AUDIO OUT jack of the DVD video player to the "DIGITAL" or "COAXIAL" input of a Dolby
Digital/DTS receiver or Processor.
• It will be helpful to also refer to the manual of the connected TV.
• Turn off the power and unplug both units before setting up any connections.
• Due to the wide dynamic range of sound output of the DVD video player, adjust the volume of your receiver to a comfortably modist
listening level to avoid any speaker damage.
• When connecting or disconnecting the DVD video player, be sure to turn off the amplifier to avoid any speaker damage.
Enjoy Dolby Digital or DTS (BEST)
Dolby Digital/DTS
Dolby Digital and DTS surround sound are currently what you hear
when you go to movies. Now you can enjoy home theater, or concert
like audio with the most amazing sound quality, in the comforts of
your own home.
Dolby Digital and DTS programming can deliver surround with five
discrete full range channels plus a sixth channel for subwoofers. You
can enjoy your APEX DVD with your Dolby Digital or DTS Digital
Surround Sound System. All you need is to connect your DVD player
to a Dolby Digital/DTS receiver, or a Dolby Digital Ready receiver with
an external (AC-3) decoder.
Connecting to Optional Equipment
To VIDEO OUT To PCM/DOLBY DIGITAL AUDIO OUT
How to setup the sound output
• From the SETUP MENU displays, set the "AUDIO OUT PUT" to "SPDIF/RAW".
• Karaoke playback can not be available with the
connection shown.
• When using microphone during Karaoke playback, you
must set the audio output to “ANALOG” from SETUP
MENU and the analog audio connection.
dts
DTS and DTS Digital Out are trademarks of Digital
Theater System, Inc.
Manufactured under license from Dolby Digital
Laboratories. Dolby and the Double-D symbol are
trademarks of Dolby Laboratories. Confidential
unpublished works. 1992-1997 Dolby Laboratories,
Inc. All rights reserved.
c
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
It is forbidden by law to copy, broadcast, show, broadcast on
cable, play in public, and rent copyrighted material
without permission.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
"
"
"
"
"
"
Enjoying Dolby Pro Logic Surround
Sound (GOOD)
Dolby Pro Logic Surround
Enjoy the dynamic realistic sound of Dolby Pro
Logic Surround by connecting an amplifier and
speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
Set "AUDIO OUTPUT" to "ANALOG" via the
setup menu.
15
APEX DIGITAL
AD-600A
Enjoying 2 Channel Digital Stereo
Sound (BETTER)
2 Channel Digital Stereo
Enjoy the dynamic sound of 2 Channel Digital
Stereo by connecting an amplifier equipped with
a digital audio input and speaker system (right
and left front speakers).
Set "AUDIO OUTPUT" to "SPDIF/PCM" via the
setup menu.
To VIDEO
OUT
To ANALOG
AUDIO OUT 2
Audio cable
Video cable
Connection
Example
To audio
input
Amplifier
equipped with
Dolby Pro
Logic Surround
To video
input
Front
speaker
(left)
Connect one or
two speakers.The
output sound from
the rear speakers
will be monaural
even if you
connect two rear
speakers.
Front
speaker
(right)
Center
speaker
Rear
speaker
To VIDEO
OUT
Video cable
Connection
Example
To digital
audio input
Amplifier equipped
with digital audio input
To video
input
Front
speaker
(left)
Front
speaker
(right)
Coaxial cable
To PCM/DOLBY
DIGITAL AUDIO OUT
TV
TV
NOTICE
• It will be helpful to also refer to the manual of the connected TV.
• Turn off the power and unplug both units before setting up any connections.
• Due to the wide dynamic range of sound output of the DVD video player, adjust the volume of your receiver to a comfortably modist
listening level to avoid any speaker damage.
• When connecting or disconnecting the DVD video player, be sure to turn off the amplifier to avoid any speaker damage.
Karaoke not available with the connection shown.
Connecting to Optional Equipment
WARNING
DO NOT set "AUDIO OUTPUT" to "SPDIF/RAW" via the SETUP MENU displays, unless connecting (Via the
PCM/DOLBY DIGITAL AUDIO OUT jack) a receiver that has the Dolby Digital/DTS decoding functions. Take precaution
for high volume sounds may damage your speakers as well as your hearing.
Continued
16
APEX DIGITAL
AD-600A
What is MP3 and VCD?
WHAT IS MP3?
MP3 is a compression form (like zip). The name MP3 stand for Mpeg1 Audio layer 3 and its compression
algorithm is based on a complicated psycho-acoustic model. This model is based on the fact that the human
ear can not hear all the audio frequencies. The human hearing range is between 20Hz to 20khz and it is
most sensitive between 2 to 4 kHz. As a result the MP3 compression form is destructive, that means the
compression algorithm causes the file to lose some information so that it can not be restored to its original
content.
When compressing an audio file (encoding) using the MP3 algorithm you can set the desired encoding level
and have any compression level you want. The larger the compressed file the better the audio quality of the
result. The majority of the files available on the internet are encoded in 128 kbits stereo 44kHz which results
in a high quality file that is 12 times smaller than the original! This, of course, has many
interesting consequences.
WHEN CREATING MP3’S
When creaing MP3’s to play on your DVD player, be sure to change the Character Settings from
Joliett to ISO 9660 in your “CD Format” properties of you favorite CD-R burning software.
For those of you using Adaptec® Easy CD Creator® 3.5 or higher, be sure to change the Mode Settings
from Mode 2 to Mode 1.
Note: The AD-600A DVD player will not play MP3 files on a CD-RW.
17
APEX DIGITAL
AD-600A
What is MP3 and VCD?
WHAT IS VCD?
A VCD looks like an ordinary 5” CD with the same digital audio quality, plus good video capability. It is a new
video format that offers a quality picture with over an hour of playing time.
Note:
1)When you playback video CD, you must turn PBC OFF in order to stop the chapter/scene.
2) The AD-600A DVD player will only play “Comercially”made VCD and SVCD’s. Apex does not now of any software
that will produce VCD’s or SVCD on a PC or MAC.
PLAY AN MP3 FORMAT
You can play an MP3 CD, by normal playback and shuffle playback.
1. Insert an MP3 CD, the DVD player will initialize the disc and the directory
will be shown on the TV screen.
Notice:
1) It may show tracks in one of the directory when you insert an MP3 CD. If you want to go
back to the main page, follow step 3.
2) Fast forward and are not available when playing MP3 CD.
3) “+” sign in front of a file name means that this is the line of the directory name, not a MP3 file.
4) PRESS the number anytime to select the number of sound tracks. For example, if you want to select a track (number 55), you have
to press “+10” 5 times then “5” key on remote control unit once.
2. Press to select sound track then press ENTER.
3. Press to select sound track then press ENTER to
play sound track. Press or during playback to skip tracks. If
you need to return to the main page, which will show all your directories, press STOP then press PROGRAM,
follow step 2 to pick up directly.
Notice: All directories will be shown on the main page even if it has sub-directories.
PLAY
ENTER
+ AATYTSAA
+ BAFGAJFG
+ CAFGADFG
+ DYTDGHJD
+ ADGGG
+ XTYYYZZZ
+ 18283
+ FGSHHHHH
Directories
PAGE 01/01
AJGALGGJ
VVVSSSGS
TYTYTITI
KDKDKDDK
AAAABBBB
CCCCDDDD
EEEEFFFF
BBBBTTTT
TTTTYYYY
QQQQWWWW
TRACKS
MP3 TRACK AATYTSAA
PAGE 01/02
+10+10 +10
+10+10 5
Continued
18
APEX DIGITAL
AD-600A
1. Press the POWER button displayed on the front panel.
The POWER indicator will illuminate, as the DVD video player turns on.
2. Press the OPEN/CLOSE button.
This will open the disc tray.
Be sure the playback side is faced
down.
3. Place the disc on the disc tray.
4. Press ENTER/PLAY
After closing the disc tray playback
will start.
As the DVD video player is reading the disc, a menu
will appear on screen.
NOTICE
• Moving the DVD video player during playback may cause damage to the disc as well as the player.
• To open and close the disc tray, you may only use the OPEN/CLOSE button on the remote control or DVD video player.
• Do not force or place anything other than DVD video disc, VIDEO CD, audio CD, or MP3 CD, on the disc tray.
Playing Back a Disc
HOW TO PLAYBACK A DISC.
Basic Playback (
see page 10 -13 for connections details)
How to playback DVD video discs or VIDEO CDs
• Turn on the TV and choose the video input source which is connected to the DVD video player.
How to enjoy the sound from the audio system
• Turn on the audio system and choose the input source which is connected to the DVD video player.
• Set the playback picture size respectedly to the ratio of the connected TV via the SETUP MENU displays.
• Set the "AUDIO OUTPUT" to "ANALOG" via the SETUP MENU displays, if you do not have the necessary
equipment to enjoy Dolby Digital (DTS) sound.
Notice
•A disc may be damaged if it is not correctly
placed on the guides in the disc tray, this
may also cause the DVD video player to
malfunction.
• Do not force or place anything other than
DVD video disc, VIDEO CD, audio CDs, or
MP3 CD on the disc tray.
Notice
• The menu screen will appear automatically
or you may access the menu screen by
pressing the TITLE button.
19
APEX DIGITAL
AD-600A
Playing Back a Disc
Continued
TITLE
ENTER/PLAY
PAUSE/PLAY
STOP
FOR A HIGHER QUALITY PICTURE
The DVD video discs produces a high resolution picture as well as contains
a lot of information. This causes periodical picture noise on the TV during
playback. The noise will vary depending on the selected TV used with this
DVD video player. To control the picture noise reduce the sharpness
adjustment on your TV when viewing DVD video discs.
ABOUT DVD VCD CD
On the heading bar the DVD VCD CD icons will appear depending on the
disc being playbacked.
DVD: DVD video discs
VCD: Video CDs
CD: Audio CDs
HOW TO START PLAYBACK FROM THE MENU SCREEN
1. Press or the number buttons to select the title.
2. Press the ENTER/PLAY button.
The DVD video player will start playback
from the title selected.
PLAY
ENTER
Title 1
Title 3
Title 2
Title 4
HOW TO PAUSE PLAYBACK (STILL PLAYBACK)
Press the PAUSE
during playback.
Press the PAUSE or ENTER/PLAY
button to resume normal playback.
During the still playback the sound
is muted.
HOW TO STOP PLAYBACK
Press the STOP button.
The DVD video player is stopped.
Press the ENTER/PLAY button to replay.
Press the STOP button twice.
Press the ENTER/PLAY button.
The DVD video player returns to chapter 1
or track 1.
HOW TO REMOVE THE DISC
Press the OPEN/CLOSE button.
Wait until the disc tray is completely open
before removing any discs.
After removing the discs, press the
OPEN/CLOSE button to close the
disc tray.
NOTICE
At the completion of each movie a menu screen will appear.
Be aware that the on-screen setup menu may damage your
TV by permanently burning that image onto the screen. To
avoid this, press the STOP button at the completion of each
movie. You may also decide to setup the SCREEN SAVER.
20
APEX DIGITAL
AD-600A
Playing Back a Disc
Continued
PLAYING AT 2X, 4X, 6X, OR 8X THE NORMAL SPEED
You can play back a disc at 2x, 4x, 6x, or 8x the normal speed.
Press the REW or FWD button during playback.
The playback speed becomes 2x the normal speed.
The playback speed changes, each time you press the REW or FWD button.
REW: Fast reverse
FWD: Fast forward
TV SCREEN
• Video CD, Audio CD
The rewind or forward playback alternates between 1x, 2x, 3x, 4x speed.
ADVANCED PLAYBACK
The DVD video player allows you to playback discs at various speeds.You may
also resume playback from the location where you stopped playback.
ENTER/PLAY
STEP
PAUSE/PLAY
REW
FWD
2X 4X 6X 8X
FF 2x FF 4x FF 6x FF 8x
2x the normal speed 4x the normal speed 6x the normal speed 8x the normal speed
PLAYING FRAME BY FRAME
Press the STEP button during playback.
The picture will advance one frame each time you press
the STEP button.
STEP
NOTICE
• The DVD video player will not playback sound and subtitles during scan reverse and forward playback of DVD video discs.The DVD
video player will play sound during fast forward or fast reverse playback of audio CDs.
• The speeds may vary slightly from disc to disc and the 2x, 4x, 6x, and 8x speeds are only approximate speeds.
• MP3 CD and CD do not have this feature.
NOTICE
• During frame by frame playback, the sound is muted.
• MP3 CD and CD do not have this feature.
Frame by
Frame
Slow
Motion
Last
Play
TO RESUME NORMAL PLAYBACK.
Press ENTER/PLAY.
TO RESUME NORMAL PLAYBACK.
Press ENTER/PLAY.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

Apex Digital AD-600A User manual

Apex Digital
Brand
Apex Digital
Model
AD-600A
Category
CD players
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents