Instruction Manual
1. GENERAL
Kit composed by a transmitter and a receiver previously memorized. The specific application is to perform a safety wireless connection when a
pedestrian pass through the pedestrian door. STOP function will be activated when the door is opened.
1 2 3 4 5
OUTPUT TYPE
- Contact NC (3-5)(C-S) (Standard operation)
- Contact NO (3-4)(B-C)
3.3 RECEIVER OPTION SELECTOR
+/~
-/~
12/24V
AC/DC
Safety OK
Fail / Sensor active /
Sensor not memorized
VCC1 C SVCC2
B
3.1 LED INDICATOR
2 APPLICATION
1
2
3
4
1
2
3
4
ON
1
2
3
4
ON
1
2
3
4
ON
1
2
3
4
ON
1
2
3
4
ON
1
2
3
4
ON
1
2
3
4
ON
1
2
3
4
ON
TRANSMITTER
FREQUENCY
AUTOMATIC
FREQUENCY
AGILITY
RECEIVER
TYPE TEST
CLASS 2
Enabled (Normative UNE-EN 13849-2)
Disabled (by default)
N.O. contact
N.C. contact
Enabled
Disabled
869,85 Mhz (Transmitter with bridge selector)
868,95 Mhz (Transmitter without bridge selector)
EN
1 - 2
Translation of the original instructions
(WIRELESSBAND 3.0)
C
3
3
C
B
4
4
B
S
5
5
S
3. TRANSMITTER & RECEIVER
1- Terminals
2- LED 1
3- Push button
4- DIP - Switch
5- LED 2
6- Buzzer
7- Antenna
Wirelessband
Rx
M
FLASH
LED ON - Security OK
LED OFF - Obstacle detected
3.2 RECEIVER TERMINALS
1- Battery CR2032
2- Programming push button
3- Antenna
4- Frequency bridge selector
RECEIVER
TRANSMITTER
Wirelessband
Tx
12 mm
28 mm
8 mm
Installation
Transmitter - Receiver
<1cm
IP55
2 yrs
Battery
100m
1 Ch
Output
14 tx
1
5
2
3
4
6
7
1
2
3
4
4. RECEIVER CHANNEL SELECTION (ONLY FOR 2 OUTPUTS RECEIVER - WIRELESSBAND 1.3 & 2.F)
2. CHANNEL STATUS
(CHANNEL 1 DEFAULT)
3. PRESS TRANSMITTER
TO CHANGE CHANNEL
4. CHANNEL CHANGED
FLASH
4-5 X
CHANNEL 1
CHANNEL 2
2 X
FLASH
PROG.
1.5s
CHANNEL 1
CHANNEL 2
5. LED FLASH
6. SAVE & QUIT
FLASH
1. INSERT BATTERY
2
0
3
2
R
C
+
l
l
i
l
t
h
e
c
u
i
m
15/06/18
WIRELESSBAND 3.0
PROG.
10s
PROG.
PROG.
1.5s
3s
1 X BEEP
PRESS
RECEIVER
KEEP IT
PRESSED
SAVE & EXIT
2 X BEEP
WAIT
RELEASE
# BEEPS
5. START-UP
6. PROGRAMMING PROCESS
CODE MEMORIZATION
MEMORY RESET
- Installation, start-up, modification and updating of the
system may only be carried out by a qualified person.
- Switch off the operating voltage before working on the system.
- The system doesn’t have fuse protection. It is recommended
include exterior protection from 100mA to 250mA.
- In case of any hypothetical issue, please do a memory reset
(point 6.).
MEMORY FULL INDICATOR
Several beeps for 10 seconds when trying to memorize a new transmitter.
LOW BATTERY INDICATOR
4 beeps each time a message is received from a programmed transmitter. Both, warning LED and buzzer are activated simultaneously.
Receiver suply voltatge
Transmitter suply voltatge
Receiver Output
Receiver Power consumption
Battery life
Ball pressure test (IEC 695-10-2)
Pollution degree
Protection class (IEC 60529)
Frecuency Channels
Range
Working temperature
Rated transient over voltage
Transmitter power consumption
Reaction time
12/24 AC/DC
2x lithium battery 3V DC type CR2032
2 Relay free voltage
0.5 W - 12 V / 1,2 W - 24 V
4 years
PCB (125ºC) WRAP (75ºC)
2
Ip55
868.95MHz & 869.85MHz
100m
-35ºC to +55ºC
330V
Transmitting 17mA / stand by 16uA
60 ms.
TECHNICAL SPECIFICATIONS
WARNING!!
CE DECLARATION OF CONFORMITY
For more information visit the website www.aerf.eu
2 - 2
1. INSERT BATTERY
+
-
12/24V
0V
AC/DC
2. CONNECT RECEIVER
POWER SUPPLY
3. CHECK OPTION
SELECTORS
4. CARRY OUT CODE
MEMORIZATION (POINT 4.)
PROG.
5. INSTALL TRANSMITTER
8. INSTALL AND WIRE
RECEIVER
10. CHECK THE SAFETY
CONTACT
CONTROL
UNIT
220V
M
9. TURN ON POWER
SUPPLY
6. MINIMUM DISTANCE
1 m.
TRANSMITTER
RECEIVER
>1m
12/24V
ON
7. MAXIMUM DISTANCE
MAGNET - TRANSMITTER
1cm.
OK?
<1cm
2
0
3
R
2
C
+
l
l
i
l
t
h
e
c
u
i
m
PROG.
1.5s
PROG.
10s
SAVE & EXIT
2 X BEEP
1 X BEEP
1 X BEEP
PRESS
TRANSMITTER
BUTTON
RELEASE
PRESS
RECEIVER
WAIT
EN
15/06/18
WIRELESSBAND 3.0
/
