RCA RCR6373N User manual

Category
Remote controls
Type
User manual

This manual is also suitable for

Battery Saver
Your universal remote control saves battery power by
automatically turning off if any key is pressed for more than
60 seconds. This saves your battery life should your remote
get stuck in a place where the keys remain depressed, such as
between sofa cushions.
RCR6373N /
RCR6473N
Universal Remote Control
Owner’s Manual
Manual del Propietario (parte posterior)
Tip: This remote is already programmed to operate
most RCA-branded TVs, VCRs, DVD players and satellite
receivers. Just press the corresponding key—DVD for
a DVD player, TV for a television, VCR•AUX2 for a VCR,
SAT•CBL•DTC for a satellite receiver, DVR•AUX1 for a DVR.
Your universal remote requires two AAA alkaline batteries (not
included).
To install the batteries:
1. Remove the battery
compartment cover.
2. Insert the batteries, matching
the (+) and (–) marks inside the
battery compartment.
3. Push the battery cover back into
place.
Battery Precautions:
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
Always remove old, weak or worn-out batteries promptly
and recycle or dispose of them in accordance with Local
and National Regulations.
To use this universal remote with your home entertainment
system, first you need to program it to control your devices.
There are four ways you can program the universal remote to
operate your devices:
The Auto Code Search goes automatically through all the
codes for the device you’re trying to control. It’s the easiest
method, but it can sometimes take longer than some of the
other programming methods.
The Brand Code Search searches through the codes for
select brands of devices. It’s not as easy as the auto code
search, but it can be faster.
The Direct Code Entry lets you enter a code from the
accompanying code list for your brand of device. It’s not as
easy as the other methods, but it’s potentially the fastest
method.
The Manual Code Search lets you manually go through
all the codes for the device you’re trying to control.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some device features don’t work, go to the next step to try
a different code.
2. Repeat the Auto Code Search Method from the beginning.
When your device turns off, do not stop searching.
Instead, with the unit now off, continue to press the PLAY
key every 5 seconds until the unit turns back on.
3. Once the unit turns back on, press the REVERSE key on the
remote every 2 seconds until your device turns off again.
When your device turns off again, press the STOP key.
4. Test the key’s functionality again by attempting to control
a variety of the device’s functions. If the code that has
been stored controls the majority of the device’s functions,
programming is complete. If the code stored does not give
maximum functionality, try another code.
Auto Code Search
The Auto Code Search goes automatically through all the
codes for the device you’re trying to control. When you nd
the one that operates your device, you can stop the search and
store that code.
TIPS: Each device key is associated with a type of device—
the TV is preset to search for TVs, SAT•CBL•DTC for satellite
receivers, digital TV converters, or cable boxes, DVD for
DVD players, and DVR•AUX1 for DVRs, AUDIO for audio
receivers, and VCR•AUX2 for VCRs. To program a device
key for a different type of device, see the Reassigning the
DVR•AUX1 and VCR•AUX2 Keys section.
To control combo devices, like TV/DVDs and TV/VCRs, you
need to program each key separately. Each key will control
that part of the combo device.
If the original remote control that came with your device has
separate ON and OFF keys (instead of a single POWER key),
the Auto Code Search might not work with that device. Try
the Direct Code Entry method described later in this manual.
To exit without saving a new code at any point in the Auto
Code Search, press the CLEAR key.
1. Manually turn on the device you
want to control.
2. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand
to press and hold the remote’s POWER key at the same
time.
3. Wait until the remote’s indicator
LED comes on and stays on.
Then release both keys.
4. Point the remote directly at the
front panel of the device you
want to control. Press PLAY on
the remote and wait 5 seconds.
The remote is testing a batch of
10 codes on your device.
Did your device turn off?
YES: Go to step 5.
NO: Press PLAY again. The remote tests the next batch of
10 codes.
Keep pressing PLAY every 5 seconds until your device turns
off.
5. When your device turns off, press
the REVERSE key on the remote
and wait at least 2 seconds.
The remote tries the last of the
previous ten codes.
Did your device turn on?
YES: Press the STOP key. You’re
done! You’ve programmed this
device key.
NO: Press REVERSE again. The remote tests the next
code in the batch.
Keep pressing REVERSE every 2 seconds until your device
turns back on. When it does, press STOP.
Note: If you accidentally press the REVERSE key after your
device turns on, press the FORWARD key. Then, wait two
seconds to see if your device turns off again.
NOTES
Throughout the programming of each key, be sure to keep
the remote pointed at the IR sensor of the device you are
currently programming the remote to control.
Test the remote with the device to make sure the
device key is programmed with the correct code for
maximum functionality. If some features don’t work, try
a different code. See the “Testing the Code for Maximum
Functionality” section below for more information.
During the Auto Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the LED blinks four
times and turns off, and the last programmed code under
that device key is retained).
The indicator light blinks four times and turns off when the
remote has gone through all the codes. The remote exits
the Auto Code Search. If your device hasn’t turned off yet,
try a different search method.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some device features don’t work, go to the next step to try
a different code.
2. Repeat the Brand Code Search from the beginning. When
the device turns off for the first time, don’t press the STOP
key, which would store the same code. Instead, with the
unit now off, continue to press the POWER key repeatedly
until the unit turns back on.
3. Once the unit turns back on, you have found another code
that operates the device. Press the STOP key.
4. Test the key’s functionality again by attempting to control
a variety of the device’s functions. If the code that has
been stored controls the majority of the device’s functions,
programming is complete. If the code stored does not give
maximum functionality, try another code.
Brand Code Search
The Brand Code Search goes through only the codes for one of
the select brands listed in the accompanying code list. If your
brand of device is listed, this search can be very quick and easy.
TIPS: Each device key is associated with a type of device—
the TV is preset to search for TVs, SAT•CBL•DTC for satellite
receivers, digital TV converters, or cable boxes, DVD for DVD
players, and DVR•AUX1 for DVRs, AUDIO for audio receivers,
and VCR•AUX2 for VCRs. To program a device key for a
different type of device, see the Reassigning the DVR•AUX1
and VCR•AUX2 Keys section.
To control combo devices, like TV/DVDs and TV/VCRs, you
need to program each key separately. Each key will control
that part of the combo device.
If the original remote control that came with your device has
separate ON and OFF keys (instead of a single POWER key),
the Brand Code Search might not work with that device. Try
the Direct Code Entry method described later in this manual.
To exit without saving a new code at any point in the Brand
Code Search, press the CLEAR key.
1. Manually turn on the device you
want to control.
3. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand to
press and hold the remote’s POWER key at the same time.
4. Wait until the remote’s indicator
comes on and stays on. Then release
both keys.
6. Point the remote directly at the
front panel of the device you want
to control. Press POWER on the
remote and wait 2 seconds. The
remote is testing a single code for
your device’s brand.
Did your device turn off?
YES: Press the STOP key to store the code. You’re done!
You’ve programmed this device key.
NO: Press POWER again. The remote tests the next code
for your brand.
Keep pressing POWER every 2 seconds until your device
turns back on. When it does, press STOP.
2. Find your device’s brand in the
Brand Code list section of the
accompanying code list. Circle
the number for your brand and
keep the list handy.
Co d e L i ts
Li s ta de Có di g os
0
1
23
4
56
7 8 9
V
V
CR
0
1
23
4
56
7 8 9
DV D
SA /CABLE
0
1
23
4
56
7 8 9
0
1
23
4
56
7 8 9
5. Look at the number you circled for
your device’s brand code number.
Press that number on the remote
keypad.
NOTES
Throughout the programming of each key, be sure to keep
the remote pointed at the IR sensor of the device you are
currently programming the remote to control.
Test the remote with the device to make sure the device
key is programmed with the correct code for maximum
functionality. If some features don’t work, try a different
code. See the “Testing the Code for Maximum Functionality”
section below for more information.
During the Brand Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the indicator light
blinks four times and turns off, and the last programmed
code under that device key is retained).
The indicator light blinks four times and turns off when the
remote has gone through all the codes. The remote exits the
Brand Code Search. If your device hasn’t turned off yet, try a
different search method.
Direct Code Entry
Direct Code Entry lets you enter a code from the accompanying
code list for your brand of device. It’s not as easy as the other
methods, but it’s potentially the fastest method.
TIPS: Each device key is associated with a type of device—the
TV is preset for TVs, SAT•CBL•DTC for satellite receivers, digital
TV converters, or cable boxes, DVD for DVD players, and
DVR•AUX1 for DVRs, AUDIO for audio receivers, and VCR•AUX2
for VCRs. To program a device key for a different type of device,
see the Reassigning the DVR•AUX1 and VCR•AUX2 Keys
section.
To control combo devices, like TV/DVDs and TV/VCRs, you need
to program each key separately. Each key will control that part
of the combo device.
1. Manually turn on the device you
want to control.
3. Press and hold the device key you want to program (the
indicator light comes on).
While you’re holding down the device key, use your other
hand enter the first five-digit code for your brand in the
code list (the indicator light goes off after the first digit).
2. Find the Code List that came with
the remote. Locate the section for
the type of device you’re trying to
program, and find your brand in
that section. Circle the codes for
your brand and keep them handy.
Co d e L is ts
Li s ta de Có di g os
0
1
23
4
56
7 8 9
TV
VC R
0
1
23
4
56
7 8 9
DV D
SA CAB LE
0
1
23
4
56
7 8 9
0
1
23
4
56
7 8 9
NOTES
Remember to enter the code for future reference in the box
provided in the Code Retrieval section of this manual.
If your brand isn’t listed in the code list, use one of the Code
Search methods to program the remote control. (Refer to the
Auto and Manual Code Search methods.)
If you release the device key any time during the Direct Code
Entry procedure, the indicator light blinks four times, and
the process is exited. The last programmed code under the
device key is retained.
Test the remote with the device to make sure the device
key is programmed with the correct code for maximum
functionality. If some features don’t work, try a different code
in the list.
4. When you’ve nished entering
the four-digit code, keep
holding down the device key
and look at the indicator light.
Is the indicator light on?
YES: You’re done! You’ve
programmed this device key.
NO, it blinked four times and turned off: You have
either entered a code number that is not in the code lists
or missed a step in the code entry procedure. Try step 3
again.
Indicator light
Manual Code Search
The Manual Code Search takes you one-by-one through all the
codes for the device you’re trying to control. When you nd the
one that operates your device, you stop the search and store that
code.
TIPS: The Manual Code Search method may take a long time
because the remote searches through all of the codes in its
memory one-by-one. If your brand is listed in the Brand Codes
or the Code Lists, rst try the Brand Code Search or the Direct
Code Entry method.
Each device key is associated with a type of device—the TV is
preset to search for TVs, SAT•CBL•DTC for satellite receivers,
digital TV converters, or cable boxes, DVD for DVD players, and
DVR•AUX1 for DVRs, AUDIO for audio receivers, and VCR•AUX2
for VCRs. To program a device key for a different type of device,
see the Reassigning the DVR•AUX1 and VCR•AUX2 Keys section.
To control combo devices, like TV/DVDs and TV/VCRs, you need
to program each key separately. Each key will control that part
of the combo device.
To exit without saving a new code at any point in the Manual
Code Search, press the CLEAR key.
Step 1: Install your batteries
Step 2: Program your remote
-
In most cases, the keys on
this remote perform the same
functions as the keys on your
original remotes once you’ve
programmed this remote to
operate your components.
Many keys on this remote
have other functions as well.
Device keys (TV,
SAT•CBL•DTC, DVD,
DVR•AUX1, AUDIO,
VCR•AUX2) put the remote in
the right mode to control your
device.
SLOW•ASPECT key changes
between full- and widescreen
formats on HDTVs; it also
activates slow playback on
DVDs and DVRs.
GUIDE and MENU put the
remote in menu/guide mode;
they also access the same
features as the keys on your
original remotes.
CLEAR exits remote
programming; it also
performs the same functions
as on your original remotes.
Arrow keys act as navigation
keys in device guides and
menu systems.
The INPUT and — (dash) key
has three functions: (1) it
toggles through all the video
or audio sources connected
to your TV or audio device;
(2) when the remote is in
VCR mode, this button
toggles between VCR and
the TV input; (3) when you’re
entering digital channel
numbers directly, this button
lets you separate the main
channel number from the
sub-channel number (such
as 59.1).
Actual model may vary from illustration
Care and Maintenance
Keep the remote dry. If it gets wet, wipe it dry immediately.
Use and store the remote only in normal temperature
environments.
Handle the remote gently and carefully. Don’t drop it.
Keep the remote away from dust and dirt.
Wipe the remote with a damp cloth occasionally to keep it
looking new.
Modifying or tampering with the remote’s internal devices can
cause malfunction and invalidate its warranty.
1. Manually turn on the device you
want to control.
2. Press and hold the device key you want to program. While
you’re holding down the device key, use your other hand to
press and hold the remote’s POWER key at the same time.
3. Wait until the remote’s indicator light
comes on and stays on. Then release
both keys.
4. Point the remote directly at the front panel of the device you
want to control. Press POWER on the remote and wait 2
seconds. The remote is testing a single code for your device.
Did your device turn off?
YES: Press the STOP key to store
the code. You’re done! You’ve
programmed this device key.
NO: Press POWER again. The
remote tests the next code for
your device.
Keep pressing POWER every 2
seconds until your device turns back
on. When it does, press STOP.
TIP: Because there are so many codes, you may have to press
the POWER key many times—possibly hundreds of times.
NOTES
Throughout the programming of each key, keep the remote
pointed at the IR sensor of the device you are programming
the remote to control.
Test the remote with the device to make sure the device
key is programmed with the correct code for maximum
functionality. If some features don’t work, try a different
code. See the “Testing the Code for Maximum Functionality”
section below for more information.
During the Manual Code Search, the remote ignores
keypresses that aren’t part of the search.
The search times out after two minutes (the indicator light
blinks four times and turns off, and the last programmed
code under that device key is retained).
The indicator light blinks four times and turns off when the
remote has gone through all the codes. The remote exits the
Manual Code Search. If your device hasn’t turned off yet, try
a different search method.
Testing the Code for Maximum Functionality
1. Try a variety of the device’s functions with the remote. If
some features of your devices don’t work, go to the next
step to try a different code.
2. Repeat the Manual Code Search and Entry Method from
the beginning. When the device turns off for the rst time,
don’t press the STOP key, which would store the same
code. Instead, with the unit now off, continue to press the
POWER key repeatedly until the unit turns back on.
3. Once the unit turns back on, you have found another code
that operates the device. Press the STOP key.
4. Test the key’s functionality again by trying a variety of
functions. If the code controls the majority of the device’s
functions, programming is complete. If the code stored
does not give maximum functionality, try another code.
Programming the DVR•AUX1 and
VCR•AUX2 Keys To Control Other Devices
The DVR•AUX1 key defaults to control a DVR, and the
VCR•AUX2 key defaults to control a VCR. If you want these
keys to control different kinds of devices (an additional TV,
DVD, satellite or cable box, for example), you must reassign it.
1. Press and hold the key you want to program (DVR•AUX1
or VCR•AUX2 key. The indicator light turns on.
2. While holding down the DVR•AUX1 or VCR•AUX2 key,
press and release the number key on the keypad for the
device you want to control (see the chart below). The
indicator light turns off.
Code Retrieval
Once you’ve programmed the remote to control your devices,
you may want to record the codes for future reference. If you
used the Direct Code Entry method, this is easy. Just find
the codes you entered and make a note of them in the boxes
below. If you used one of the Code Search methods to program
your remote or if you used the Direct Entry method but don’t
remember the code, you will need to retrieve each device’s
four-digit code. Retrieving the actual code and writing it down
will save you time if you ever need to program the remote
again. If the codes are recorded, you can use the Direct Entry
method to reprogram your remote to control your devices,
which is quick and easy.
1. Press and hold the device key
(TV, SAT•CBL•DTC, DVD, AUDIO,
VCR•AUX2, DVR•AUX1) whose
code you wish to retrieve. The
indicator light turns on. Keep
pressing the device key.
2. While holding the device key down, press and hold the
INFO key. The indicator light turns off. After holding down
both keys for three seconds, the light turns back on.
3. Release both keys. The indicator light remains on.
4. Starting with the number 1 key, press and release each
number key on the keypad in the following order: 1-9, then
0. The number that causes the indicator light to blink is the
first number of the code. As you find each number of the
code, write it down for future reference. Then start with the
number 1 key again.
Note: All TV codes start with the number 1; all VCR and
DVR codes start with the number 2; all DVD players codes,
the number 3; all audio device codes, the number 4; and all
satellite receiver, cable box, and digital TV converters, the
number 5.
5. Repeat step 4 until you have retrieved all five numbers in
the code. After the fifth number is retrieved, the indicator
light blinks briefly, then turns off.
TIP: To exit the Code Retrieval Mode at any time, press the
CLEAR key.
Note: If you press an invalid key during the Code Retrieval
process, the remote will not respond. If you do not press
a valid Code Retrieval key (TV, SAT•CBL, DVD, DVR•AUX1,
AUDIO, VCR•AUX2, INFO, CLEAR), Code Retrieval times out
after 15 seconds. The indicator light blinks four times, and
then turns off.
IMPORTANT
Because this remote controls more than one device, you
must rst “tell” the remote which device you wish to
operate. That means, if you wish to operate your TV, you
must rst press the TV key to put the remote in the TV
Mode. The remote stays in that device mode until you press
a different device key. For example, if your remote is in TV
Mode and you want to operate the DVD player, you must
press the DVD key to change device modes.
Problem: The remote does not operate your device.
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD, DVR•AUX1,
AUDIO, VCR•AUX2). This tells the remote which device to
operate.
Remove any obstacles between the remote and the device. Make
sure you’re aiming the remote at the device’s IR sensor.
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if necessary
(see the Battery Installation section).
Problem: The remote can’t be programmed to operate your
device.
If you are testing the remote while programming it, you may be
too far away from the device or at a wrong angle. There must be
an unobstructed path between the remote and the IR sensor on
the device. Move closer and make sure you point the remote at the
device you’re trying to control.
If you’re using the Direct Entry programming method to enter
the codes for your brand and the unit is still not functioning
properly, try the auto, brand, or manual search method.
To control combo units, like TV/VCRs or TV/DVDs, you must
program the individual corresponding device keys to control
each part of the combo unit. Once programmed successfully, the
TV key controls the TV functions, and the DVD or VCR•AUX2 key
controls the DVD or VCR functions.
Make sure the batteries are fresh and are properly installed.
Problem: The remote doesn’t perform commands properly.
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD, DVR•AUX1,
AUDIO, VCR•AUX2). This tells the remote which device to
operate.
Make sure device is ready (for example, the DVD player has a
disc loaded).
You may have pressed an invalid key for the mode the remote is in.
If you’re trying to enter a channel number directly, try pressing
the ENTER key after entering the channel number as this is a
requirement of certain models and brands.
There is a possibility that a programmed code may only be
able to control some of your device features (for example, only
turns a device on and off). To confirm that the device key is
programmed with the correct code for maximum functionality,
test the device. Attempt to control a variety of the device’s
functions with the remote. If some of the features of your
devices don’t work, try programming the remote with a different
code in the list using the Direct Code Entry Method, until you
find the code that allows the remote to control the majority of
your device’s functions. Different codes can provide different
levels of functionality.
Problem: The indicator light does not come on when you press
a key.
You may have pressed an invalid key for the mode the remote is
in.
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD, DVR•AUX1,
AUDIO, VCR•AUX2). This tells the remote which device to
operate.
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if necessary
(see the Battery Installation section).
Problem: The remote will not change channels on device.
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD, DVR•AUX1,
AUDIO, VCR•AUX2). This tells the remote which device to
operate.
Press the ENTER key after you enter a channel number.
Remove any obstacles between the remote and the device. Make
sure to aim the remote at the IR sensor on the device.
Problem: The device’s menu does not appear on the TV screen.
Make sure you have connected the device to your TV properly and
selected the correct input. (See your devices’ Owner’s Manuals for
proper connection procedures.)
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD, DVR•AUX1,
AUDIO, VCR•AUX2). This tells the remote which device to
operate.
Menu access isn’t supported for all brands. You may need to use
your original remote control to access menu functions for some
devices.
For more information, please visit www.rcaaccessories.com
Consumer Help Line: 1-800-420-7968
Audiovox Electronics Corporation (theCompany”) warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during
its lifetime while you own it, such defect(s) will be repaired or replaced
(at the Company’s option) without charge for parts and repair labor. To
obtain repair or replacement within the terms of this Warranty, the product
is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to the Company at the
address shown below.
This Warranty does not cover product purchased, serviced or used outside
the United States or Canada. This Warranty is not transferable and does
not extend to costs incurred for installation, removal or reinstallation of
the product. This Warranty does not apply if in the Companys opinion,
the product has been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or the simultaneous use of different
battery types (e.g. alkaline, standard or rechargeable).
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO
EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE
PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL
BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL
THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER. No person or representative is authorized
to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This
Warranty gives you specic legal rights and you may also have other rights,
which vary from state/province to state/province.
U.S A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,
New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
Trademark(s) ® Registered
RCR6373N US 00 RCR6473N US 00
©2009 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Tour of the Remote Advanced Functions Troubleshooting
Limited Lifetime Warranty
-
Indicator
light
DVR•AUX1 or VCR•AUX2 KEY CONTROLS:
Additional TV press 1
VCR or DVR press 2
Additional DVD press 3
Additional audio device press 4
Additional satellite receiver,
cable box, or DTV converter
press 5
3. Release the DVR•AUX1 or VCR•AUX2 key. The indicator
light blinks four times and then turns off. The DVR•AUX1
or VCR•AUX2 key is now set to control the device type you
selected.
4. Follow the directions in the auto, brand, direct entry,
or manual code search to program the DVR•AUX1 or
VCR•AUX2 key.
Volume Punch-Through
Volume Punch-through allows the VOL and MUTE keys, when
pressed in SAT•CBL•DTC, DVD, DVR or VCR modes, to “punch
through” to either TV or AUDIO, whichever was accessed last.
Volume Punch-Through occurs automatically and allows you to
control the volume without exiting the current mode. (If either
AUX key has been programmed with a TV or AUDIO code,
volume can punch through to these devices as well.)
Note: Volume Punch-Through does not occur in cases where
the component code has its own volume/mute controls, such
as some satellite receivers.
Advanced Punch-Through
Volume Punch-Through, as described above, occurs
automatically. If you want to specify whether Volume Punch-
Through is directed to the TV or AUDIO while in SAT•CBL,
DVD, DVR•AUX1 or VCR•AUX2 modes, follow the steps below.
Note: This option can also be enabled for an AUX key, if it is
programmed with a VCR, DVR, DVD, CD, SAT or TV code.
1. Press and hold the key whose volume commands you
want to send to the TV or audio device. The indicator light
turns on.
2. While holding down the device key, press and hold the
VOL up key. The indicator light turns off.
3. After holding down both keys for 3 seconds, the indicator
light turns on and stays on. Release both keys.
4. Press and release the device key you want the Volume
Punch-Through to be directed to from the selected mode
(TV, AUDIO or AUX key). The indicator light ashes, then
turns off.
Note: The device key pressed in step 4 must be programmed
with a TV or AUDIO component. If an invalid key is pressed,
the LED ashes four times, then turns off.
Important: Once you have programmed any device with a
specied Volume Punch-Through, the Volume Punch-Through
for all other devices defaults to AUDIO. If you do not want
other components’ Volume Punch-Through to default to
AUDIO, you must manually program them, using steps 1-4.
5
sat•cbl•dtc code
SAT DTV CONVERTER CABLE
dvr•aux1 code
DVR/VCR DVD TV SAT•CBL•DTC
1
tv code
3
dvd code
4
audIo code vcr•aux2 code
DVR/VCR DVD TV SAT•CBL•DTC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

RCA RCR6373N User manual

Category
Remote controls
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages