Paradigm OM-605 User manual

Brand: Paradigm

Model: OM-605

Category: Subwoofers

Type: User manual

This manual is also suitable for

IN-WALL SUBWOOFERS

Thank you for choosing award-winning Paradigm

Reference

in-wall subwoofer systems and congratulations! You are about

to experience the stunning difference these state-of-the-art high-end

subwoofers will make in your music and home theater system.

Comprehensive R&D, leading-edge design, use of the finest materials and

sophisticated manufacturing and quality control techniques provide

vastly superior performance for each component part at every stage of

design. Paradigm

Reference subwoofers will provide you with stunning

high-end sound and unparalleled listening pleasure for years to come.

To achieve all of the exceptional sound that these subwoofers are

capable of providing requires care in installation and operation. Please

take the time to read this manual as well as the manual that came with

your Paradigm

subwoofer amplifier and follow all instructions. If you

have further questions, contact your Authorized Paradigm

Reference

Dealer or visit the Q&A page in the Tech Support section of our website

at www.paradigm.com.

Paradigm Electronics Inc. In Canada: 205 Annagem Blvd., Mississauga, ON L5T 2V1• In the U.S.: MPO Box 2410, Niagara Falls, NY 14302

IMPORTANT: Subwoofers covered by this manual are designed for

use with a Paradigm

Subwoofer Amplifier only. Use with any other

brand of amplifier can cause permanent damage and will void the

Paradigm warranty.

OWNERS MANUAL OM-605

THE ULTIMATE IN HIGH-END SOUND FOR MUSIC AND HOME THEATER

™

RECYCLING AND REUSE GUIDELINES FOR EUROPE

In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment)

directive effective August 13, 2005, we would like to notify you that this product may

contain regulated materials which, upon disposal, according to the WEEE directive,

require special reuse and recycling processing. For this reason ParadigmElectronics Inc.

(manufacturers of Paradigm

speakers and Anthem

electronics) has arranged with our

distributors in European Union member nations to collect and recycle this product at

no cost to you. To find your local distributor please contact the dealer from whom you

purchased this product or go to our website at www.paradigm.com.

Please note that the product only falls under the WEEE directive. When disposing of

packaging and other shipping material we encourage you to recycle through the

normal channels.

DIRECTIVES EUROPEENNES SUR LE RECYCLAGE ET LE TRAITEMENT DES DECHETS

Dans le respect de la directive WEEE (Waste Electrical & Electronic Equipment) mise en place par les

institutions Européennes à compter du 13 Août 2005, nous souhaitons vous informer que ce produit peut

contenir des matières devant faire l’objet d’une procédure de recyclage ou de traitement approprié des

déchets. Dans cette optique, Paradigm Electronics Inc (fabricant des enceintes Paradigm

et des

électroniques Anthem

) avec ses Distributeurs agréés dans l’Union Européenne, ont mis en place une

procédure de collecte et de retraitement gratuite. Pour en savoir davantage sur cette procédure veuillez

contacter votre revendeur, ou notre Distributeur dans votre pays (vous en obtiendrez les coordonnées sur

simple demande ou en consultant notre site Internet www.paradigm.com).

Notez que seul le produit fini est concerné par cette directive et ses obligations. S’agissant de son emballage

et de ses accessoires de transport nous vous recommandons de les recycler selon les procédures mises en

place par votre commune ou votre département.

TO PREVENT DAMAGE TO AMPLIFIER OR SUBWOOFER

AND ENSURE OPTIMAL SOUND, THE 3-POSITION “EQ”

SWITCH ON THE REAR PANEL OF THE AMPLIFIER MUST

BE CORRECTLY CONFIGURED FOR USE WITH YOUR SETUP

(See Fig. 2). Additional details on page 5.

USING THE X-300 AMPLIFIER:

IMPORTANT OPERATING INSTRUCTIONS: READ BEFORE

OPERATING SUBWOOFER

TO PREVENT DAMAGE TO AMPLIFIER OR SUBWOOFER, FOLLOW THE

INSTRUCTIONS THAT RELATE TO YOUR SETUP BELOW. FAILURE TO

FOLLOW THESE INSTRUCTIONS WILL RESULT IN PERMANENT DAMAGE TO

AMPLIFIER AND SUBWOOFER. SUCH DAMAGE IS NOT COVERED UNDER

THE PARADIGM WARRANTY.

TO PREVENT DAMAGE TO AMPLIFIER OR SUBWOOFER, THE

IMPEDANCE MATCHING SWITCH ON YOUR SUBWOOFER’S

BAFFLE MUST BE POSITIONED FOR USE WITH THE

DESIGNATED AMPLIFIER (See Fig. 1).

POSITIONING THE IMPEDANCE MATCHING SWITCH:

TABLE OF CONTENTS

Important Operating Instructions:

Read Before Operating Subwoofer . . 3

Subwoofer Assembly Parts List . . . . 4

Impedance Matching Switch

(Pictorial) . . . . . . . . . . . . . . . . . . . . . . . 4

3-Position “EQ” Switch (Pictorial). . . 4

Your New Subwoofer . . . . . . . . . . . . . 5

Configuring the Amplifier

for use with Your Subwoofer . . . . . . 5

The Listening Room . . . . . . . . . . . . . . 6

Guidelines for Deciding

on S ubwoofer Placement . . . . . . . . . 6

Subwoofer Placement . . . . . . . . . . . . 7

Color-Match Painting . . . . . . . . . . . . . 8

Installation into a Wall

Without a Backbox (Pictorial) . . . . . . 8

Installation into a

Paradigm

Backbox (Pictorial). . . . . 10

Installation into a Wall

Without a Backbox . . . . . . . . . . . . . . 11

Limited Warranty . . . . . . . . . . . . . . . 13

• 1 subwoofer

• 1 mounting template

• 1 MDF mounting frame

• 8 mounting screws

• 4 gasket tape strips

• 2 port gaskets (5/8˝ drywall installation only)

• 1 paint mask

• 1 wire tie

SUBWOOFER ASSEMBLY PARTS LIST

(each subwoofer)

IMPEDANCE MATCHING SWITCH

(all models)

Fig. 1

X-850X-300

3-POSITION “EQ” SWITCH

(X-300 Amplifier only)

Fig. 2

All PCS subs with/without backbox

& RVC-12SQ without backbox

RVC-12CF with/without backbox

RVC-12SQ with backbox

All PCS subs with/without backbox

& RVC-12SQ without backbox

RVC-12CF with/without backbox

RVC-12SQ with backbox

Required, not included

• 1 Paradigm

X-300 Amplifier (for use with 1 Paradigm

Reference RVC subwoofer)

or 1 Paradigm

X-850 Amplifier (for use with 1 or 2 Paradigm

Reference RVC subwoofers)

Break-In

Allow your Paradigm

Reference subwoofer system to operate for several hours before you listen critically.

Cleaning

Clean subwoofer housing with a soft, damp cloth. Do not use a strong or abrasive cleaner or get any part of

the subwoofer wet.

If you wish to paint your subwoofer you must do so before installing it. See the section on ”Color Match

Painting” later in this manual for full details.

Optional Paradigm

Backbox

Paradigm

Reference in-wall subwoofers can also be installed into an optional Paradigm

Backbox

(sold

separately).

If you decide to use a backbox, follow the instructions for placement and installation included with

the backbox. NOTE: If you install your subwoofer into a Paradigm

Backbox, you will not require the MDF

mounting frame that came with your subwoofer.

YOUR NEW SUBWOOFER

Setting 1: Use this setting with one RVC-12SQ subwoofer without a backbox

Setting 2: Use this setting with one RVC-12CF subwoofer with or without a backbox

Setting 3: Use this setting with one RVC-12SQ subwoofer with a backbox

NOTE: These settings are also displayed on your amplifier’s back panel.

WARNING: The following procedures are imperative for correct system

setup. Failure to follow the instructions that apply to your setup will result

in permanent damage to amplifier and subwoofer. Such damage is

NOT

covered under the Paradigm warranty.

1. The Impedance Matching Switch on Your Subwoofer’s Baffle:

To prevent damage to amplifier or subwoofer, the Impedance Matching Switch on your subwoofer’s

baffle must be correctly positioned (Fig. 1).

2. Using the Paradigm

X-300 Amplifier with Your Subwoofer:

To prevent damage to amplifier or subwoofer and ensure optimal sound, the 3-Position “EQ” Switch on

the X-300 amplifier’s rear panel must be correctly configured for use with or without

a Paradigm

Backbox.

Toggle to the setting that matches your setup (Fig. 2):

3. Using the Paradigm

X-850 Amplifier with Your Subwoofer:

Your X-850 amplifier comes with a Setup CD that allows you to configure your Paradigm

Reference

subwoofer system for optimal sound

PC requirements for running this CD are Windows XP or Vista and

one USB port. Install the software and perform the setup before connecting your amplifier to

the subwoofer. For complete instructions on installing the software, refer to the Owners Manual that

came with your X-850 amplifier.

CONFIGURING THE AMPLIFIER FOR USE WITH YOUR

SUBWOOFER

Paradigm

Reference in-wall subwoofers are suitable for use in a wide variety of listening environments.

Note however, that room construction, dimensions and furnishings all play a part in the quality of sound you

ultimately achieve. Try to follow these guidelines:

a) Strong, rigid walls are preferred for best bass balance. For even better results we recommend adding additional

bracing and acoustic damping material to the cavity prior to installation. See section on ”Installation Into

A Wall Without A Backbox” later in this manual for more details.

b) It is important to note that just as the amount of soft furnishings has a decided impact on mid and high

frequencies, those frequencies below 150 Hz are dramatically affected by the room itself—its size, shape,

as well as the physical boundaries of the room.

The extra care you take in correctly positioning your subwoofers will result in greater listening enjoyment.

Follow the guidelines for placement below to achieve optimal sound in your room.

THE LISTENING ROOM

When considering subwoofer placement directly into a wall, keep the following in mind:

• DO NOT install subwoofer in lath or plaster—over time, the bass vibrations will cause material to crack;

• DO NOT install subwoofer in cavities that contain ductwork;

• DO NOT locate subwoofer close to wall-mounted fixtures that may vibrate (remember to check the other

side of the wall too!);

• DO NOT install subwoofer in a cavity that already contains an in-wall speaker;

• If installing subwoofer in a wall with metal studs, make sure the studs are securely fastened so that they do

not vibrate or rattle;

• Some acoustic bleed-through in the adjacent room is unavoidable. See section on “Installation Into A Wall

Without a Backbox” later in this manual for suggestions to reduce bleed-through.

(Guidelines and suggestions for the actual installation process can be found later in this manual.)

GUIDELINES FOR DECIDING ON SUBWOOFER PLACEMENT

Fig. 3a

Two subwoofers close to floor in corners of room

Bass is less and less directional as it goes down in frequency. For best sonic integration, placing your subwoofer

in the wall at the front or rear of the room and close to a corner usually provides the best bass performance and

sonic integration. If this location is not possible, keeping in mind the guidelines provided earlier

, you may place

your subwoofer anywhere in the wall without affecting the stereo image of your front speakers or the soundstage

of your multi-channel speaker system.

Figs. 3a and 3b below highlight how bass output is generally affected by in-wall placement. When seated in

the typical listening area of your room, placing the subwoofers in the various positions will typically result in

bass performance as follows:

Fig. 3a: Corner placement close to the floor provides the best balance of output and accuracy.

Fig. 3b: Placement anywhere along the wall close to the floor but outside the "shaded" area will provide

slightly reduced output, though still acceptable accuracy.

The Advantages of Using Two Subwoofers

We highly recommend using two Paradigm

Reference in-wall subwoofers in your music and home theater

system. Using two subwoofers allows you to randomize the standing waves within your listening room so that

bass is distributed in a more uniform manner. Using two subwoofers can also ensure even lower distortion,

especially at high output levels.

If desired, for further optimized bass performance and even greater output, you can install an additional pair

of Paradigm

Reference in-wall subwoofers. Figure 4 provides recommended placement for four subwoofers.

Broken lines in figures below represent alternate placement for two subwoofers.

SUBWOOFER PLACEMENT

Fig. 3b

Two subwoofers close to floor in middle of walls

Fig. 4

Recommended placement for four subwoofers in a wall

Fig. 5c

Fig. 5a

Your new subwoofer has a textured finish in neutral white to blend into any area. It may also be painted to

match any décor. If you plan to paint your subwoofer, to avoid “painting it to the wall”, we recommend that

you paint it before installation.

Please note:

• Do not paint the surface behind the grille

• Do not heat-cure your newly painted subwoofer

• Avoid painting the subwoofer’s rear surface—protect it by masking the surface

(paint mask included)

To Paint, Follow These Steps:

1) Remove the metal grille and position the paint mask

(included)

in its place;

2) In a well-ventilated area, apply several light coats of paint, letting the subwoofer housing dry completely

between coats. Follow the paint manufacturer’s directions;

3) When painting grille, be careful n ot to plug holes with paint and re-attach after paint has dried. It is

easier to spray the grille than to use a brush. Remove grille before painting

COLOR-MATCH PAINTING

(optional)

Connect subwoofer as outlined in the Owners Manual included with your Paradigm

subwoofer amplifier.

INSTALLATION INTO A WALL WITHOUT A BACKBOX

Positioning block should be at bottom, facing you as

you tip frame into wall.

Fig. 5b

Peel tape back.

NOTE: Gasket tape strips must overlap at each corner

for a complete seal.

Fig. 5d

Fig. 5e

INSTALLATION INTO A WALL WITHOUT A BACKBOX

(continued)

Fig. 5g

Fig. 5f

IMPORTANT! DO NOT remove port covers.

Fig. 6

Installation into 5/8˝ drywall requires additional sealing around ports. Peel backing and carefully align

port gaskets with rim of ports

(as shown)

. Press to adhere.

Connect subwoofer as outlined in the Owners Manual included with your Paradigm

subwoofer amplifier

and Paradigm

Backbox installation instructions.

INSTALLATION INTO A PARADIGM

BACKBOX

Fig. 7

To prevent air leaks, before installing subwoofer, apply gasket tape

(included with subwoofer)

along all

four outer edges of box, overlapping tape at corners (as shown in Fig. 7). Remove port covers by pressing

them out

(as shown)

Holding subwoofer firmly, push it into backbox being careful to align top holes in subwoofer frame with

top holes in backbox. Screw in until firm but not fully tightened. Continue holding subwoofer while lining

up all bottom holes. Again, screw in until firm but not fully tightened. Insert remaining screws. Tighten

all screws.

Fig. 8

INSTALLING GRILLE

All other installations go

directly to Fig. 7.

For subwoofer to

function correctly

and avoid damage

to amplifier or subwoofer, the

Impedance Matching Switch

must be correctly positioned

Move the switch position to

reflect designated amplifier.

(Fig. 1) Refer to the Owners

Manual included with the

amplifier for more info.

INSTALLING INTO

5/8˝ DRYWALL

IMPORTANT! INSTALLING SUBWOOFER INTO A PARADIGM

BACKBOX

Instructions for installing your subwoofer into a backbox were provided with the backbox. If you no longer

have those instructions, follow the instructions on the previous page.

STIFFENING AND STRENGTHENING THE CAVITY

Although Paradigm

in-wall mounting systems are the most rigid on the market, when installing your

subwoofer directly into a wall, to minimize acoustic bleed-through, we recommend the following:

Additional Bracing

Additional cross-bracing will further stiffen the cavity. We suggest placing two to three pieces of 2˝ x 4˝

(more if application allows) within the cavity, evenly spaced above and below the cutout. Additional

bracing can also be sandwiched to the studs on either side of the subwoofer.

New Construction

New construction offers an excellent opportunity to strengthen and stiffen the cavity with additional

bracing or construction-grade stiffening adhesives applied directly to the drywall.

(See Dealer for

more information.)

1. Mounting

TIP!

Damping the cavity may be done before or after installing the MDF mounting frame. See subsection

“Damping Material and Other Acoustic Treatments” on next page.

a) Keeping in mind the recommendations for placement provided earlier, place cardboard mounting

template onto wall. Cut hole as indicated (Fig. 5a).

Installing the MDF Mounting Frame:

Your Paradigm

Reference in-wall subwoofer comes with an MDF mounting frame. DO NOT

try to install frame on the outside of the hole, it is designed to sit behind the cutout, providing

support for the weight of the subwoofer

b) Remove double-sided tape (Fig. 5b).

c) Tip frame into wall cutout (Fig. 5c).

TIP!

The MDF frame has a raised positioning block to help you align it with the cutout. Position frame

so that block is at bottom, facing you. Angle frame slightly to make it easier to tip into wall.

d) Using the block as your guide, pull frame toward you so that it aligns on all sides with inside edges

the cutout. The block will protrude through the opening at bottom (Fig. 5d).

TIP!

Press frame firmly against the inside of the wall, smoothing on all sides to engage adhesive. Once

tape adheres to wall it will be difficult to reposition frame, so correct alignment initially is very important.

e) Remove positioning block by removing screws that hold it in place; discard (Fig. 5e).

f) To prevent air leaks, before installing subwoofer, apply gasket tape

(included)

along all four sides of

MDF frame (as shown in Fig. 5f). Tape must overlap on all four corners.

INSTALLATION INTO A WALL WITHOUT A BACKBOX

1. Mounting

(continued)

Damping Material and Other Acoustic Treatments

TIP!

To ensure optimal results, do not compact damping material during the damping process. Additional

soundproofing treatments

(i.e. Dynamat

)

can be used against the back wall of the cavity as well as on

the inside front of the wall

(see Dealer for more information)

Damping the Cavity:

For optimum performance, loosely place a minimum of …

• Two pieces, 8˝ (20 cm) to 12˝ (30 cm) long, of standard fiberglass insulation in the wall. R-12 for 2˝ x 4˝

(5 cm x 10 cm) walls or R-20 for 2˝ x 6˝ (5 cm x 15 cm) walls. Place one piece just above and the other

just below the mounting hole;

• A half-thick piece of fiberglass insulation, the same height as the subwoofer, in the wall directly behind

the mounting hole, allowing enough space for the subwoofer to properly recess into the cavity.

2. Connecting and Installing

You are now ready to connect and install the subwoofer. If you are color-match painting do so now

before proceeding. Follow the painting instructions provided earlier.

With grille removed …

Connecting Subwoofer:

Connect subwoofer cable as outlined in the Owners Manual included with your Paradigm

subwoofer

amplifier

(sold separately)

. Once connected …

Installing Subwoofer

(Fig. 5g):

Leave port covers in place. (Covers are only removed if installing into an optional Paradigm

Backbox.)

IMPORTANT!

Installation into 5/8˝ drywall requires additional sealing around ports (Fig. 6).

Holding the subwoofer firmly …

a) Tip it into the mounting frame, making sure the holes in the top of the MDF frame align with the

holes in the top of the subwoofer frame.

b) Insert screws into top holes. Screw in until firm, but not fully tightened.

c) Continue holding subwoofer firmly while lining up bottom holes in MDF frame with bottom holes

in subwoofer frame. Again, screw in until firm, but not fully tightened.

d) Insert all remaining screws, then firmly tighten all screws.

3. Installing the Grille

Press the grille into the groove on the front face of the subwoofer (Fig. 8).

INSTALLATION INTO A WALL WITHOUT A BACKBOX

(continued)

IMPORTANT: Subwoofers covered by this

manual are designed for use with a Paradigm

Subwoofer Amplifier only. Use with any other

brand of amplifier can cause permanent damage

and will void the Paradigm warranty.

Paradigm

subwoofers covered by this manual are

warranted to be and remain free of manufacturing

and/or material defects for a period of three (3)

years from the date of the original retail purchase.

Within the time period specified repair, replacement

or adjustment of parts for manufacturing and/or

material defects will be free of charge to the

original owner.

Thermal or mechanical abuse/misuse is not

covered under warranty.

Limitations:

• Warranty begins on date of original retail

purchase from an Authorized Paradigm

Dealer

only. It is not transferable;

• Warranty applies to product in normal home use

only. If the product is subjected to any of the

conditions outlined in the next section, warranty

is void;

• Warranty does not apply if the product is used in

professional or commercial applications.

Warranty is Void if:

• The product has been abused (intentionally or

accidentally);

• The product has been used in conjunction with

unsuitable or faulty equipment;

• The product has been subjected to damaging

signals, derangement in transport, mechanical

damage or any abnormal conditions;

• The product has been tampered with or damaged

by an unauthorized service facility;

• The serial number has been removed or defaced.

Owner Responsibilities:

• Provide normal/reasonable operating care and

maintenance;

• Provide or pay for transportation charges for

product to service facility;

• Provide proof of purchase (your sales receipt

given at time of purchase from your Authorized

Paradigm

Dealer).

Should servicing be required, contact your nearest

Authorized Paradigm

Dealer, Paradigm

Electronics

Inc., or Import Distributor (outside the U.S. and

Canada) to arrange, bring in or ship prepaid any

defective unit.

Visit our website at www.paradigm.com for

more information.

Paradigm Electronics Inc. reserves the right to

improve the design of any product without assuming

any obligation to modify any product previously

manufactured.

This warranty is in lieu of all other warranties

expressed or implied, of merchantability, fitness for

any particular purpose and may not be extended or

enlarged by anyone. In no event shall Paradigm

Electronics Inc., their agents, or representatives be

responsible for any incidental or consequential

damages. Some jurisdictions do not allow limitation

of incidental or consequential damages, so this

exclusion may not apply to you.

Retain this manual and your sales receipt for

proof of warranty term and proof of purchase.

LIMITED WARRANTY

Page is loading ...

REMARQUE : Le ruban à joint doit couvrir chaque coin.

Fig. 12d

Fig. 12e

INSTALLATION DANS LE MUR SANS BOÎTIER ARRIÈRE

(suite)

Fig. 12g

Fig. 12f

IMPORTANT! NE PAS retirer les couvercles

de port.

Page is loading ...

www.paradigm.com

MAN0000605

120808

Paradigm OM-605 User manual

Brand: Paradigm

Model: OM-605

Category: Subwoofers

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Paradigm OM-605 Manuel utilisateur

Paradigm OM-605 User manual

This manual is also suitable for

Paradigm OM-605 User manual

in other languages

Related papers

Other documents