MANUALE UTENTE – USER’S MANUAL
SCOOPSCAN 575ECN
PLSC575ECN
Rev. 09/2006
2
INDICE
DESCRIZIONE........................................................................................................... 3
SPECIFICHE TECNICHE........................................................................................... 3
ISTRUZIONI DI SICUREZZA...................................................................................... 4
ACCESSORI COMPRESI NELL’IMBALLO ................................................................ 4
ISTRUZIONI PER L’INSTALLAZIONE........................................................................ 4
ISTRUZIONI OPERATIVE.......................................................................................... 5
CANALI....................................................................................................................... 7
TABLE OF CONTENTS
DESCRIPTION........................................................................................................... 8
TECHNICAL SPECIFICATION................................................................................... 8
SAFETY INSTRUCTIONS.......................................................................................... 9
ACCESSORIES SHIPPED TOGETHER WITH THE MACHINE................................. 9
INSTALLATION INSTRUCTIONS .............................................................................. 9
OPERATION INSTRUCTIONS................................................................................. 10
CONTROL CHANNELS............................................................................................ 12
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
8
DESCRIPTION
Thank you for selecting Proel Scoopscan 575ECN. In order to ensure your safety and
use the light properly, please read this menu carefully and observe the rules strictly.
This Scoopscan 575ECN adopts an advanced processing and an efficiency optical
system to generate high precision and very bright beam.
This unit is a good choice for TV station, theatre, disco and show room.
TECHNICAL SPECIFICATION
- Rated Voltage: AC 230V / 50Hz (AC 120V / 60Hz USA)
- Lamp: OSRAM HMI 575GS
- Insulation resistance: > 2MΩ
- Number of channels: 8
- Control signal: DMX 512
- Color temperature: 3200K, 6000K
- Colour effect: 4 colors + white
- Gobo effects: 5 rotating gobos + white
- Strobe flash: 1-7 flash/second
- Angle of beam: 15°
- Dimmer: linear 0-100%
- Scanning angle: 150° Pan – 110° Tilt
- Dimensions: 960 x 400 x 230
- Net weight (Kg): 31
9
SAFETY INSTRUCTIONS
130
High Temperature LampAvoid Current-Passing
• Inquiry a qualified maintainer before you maintain the product.
• Make sure the light power off before you install the lamp or move the equipment.
• Don’t use the different power voltage or different kinds of lamp.
• During use this light, it may generate high temperature to cause danger. Please
don’t put any inflammable or explosive material near the equipment, don’t touch
the light directly by hand.
• Make sure the distance of the equipment and is over 1 meter
• Don’t look at the lamp directly to avoid eyes injury
ACCESSORIES SHIPPED TOGETHER WITH THE MACHINE
• Scoopscan 575ECN (1 pc)
• XLR cable (1 pc)
• User manual (1 pc)
• Fasten knob, washer for fly ring 2 set
INSTALLATION INSTRUCTIONS
• This product is fit to be used indoors, its ambient operating temperature lower
than 35°C.
• People assigned to install, operate and maintain the product must familiarize
themselves with the performance of the light fixture before they begin the
operations. Most damages result from incorrect operations arising out of
unfamiliarity with the performance of the product.
• Before the product begins to be used for the first time, please open the package
to check if there are any damages caused during transportation
• Before replace the lamp, please make sure the power have been cut off, and
wait until the light cool down (the temperature of the lamp can reach 200°C or
more).
10
• Unscrew the four lamp’s protection grids
• Open the lamp lid , and replace the lamp . Be care not to touch the surface of
the new lamp.
• Close the lid.
• Install the light fixture in a place that is well ventilated. Pay attention to checking
if the fan and fan net are smooth.
• The Scoopscan 575ECN uses the 5A / 250V safety fuse. Please use a fuse with
the same specification.
OPERATION INSTRUCTIONS
Scoopscan 575ECN adopts international standard DMX-512 signal, multiple lights can
be controlled by the controller due to use the channel setting (the details are listed in
Appendix 2).
For all installation, having long signal cables or in the presence of electrical noise, for
example a discotheque, it is recommended practice to use a DMX terminator: this assist
in preventing corruption of the digital control signal by external noise. The DMX
terminator is simply an XLR connector with a 120Ω (Ohm) resistor connected across
pins of + and – signals.
The Scoopscan 575ECN uses core XLR outlet (plug). A transfer line from 5 core to 3
core will be needed if the controller you use is 5 core outlet (plug). (Please refer to
Appendix 1).
The lamp reaches its full power after 5 - 10 minutes since you powered on the unit. For
this reason, once you switched off the lamp, you must wait at least 10 minutes before
switching on the lamp one more time.
When power is on, the equipment will undertake self-examination, and can undertake
operation after the self-examination is finished.
Please don’t shake the equipment when it is in operation.
Page is loading ...
12
CONTROL CHANNELS
The Scoopscan 575ECN uses international standard DMX512 signal. There are 8
control channels and the detailed information of control is as follow:
CHANNEL DMX Value Control description
STROBO 0 – 137 Strobo
1
DIMMER 128 - 255 Dimmer lineare
2 GOBO 0 - 255 Setting between 5 gobos
COLOR 0 – 137 Setting between 4 colors + white
3
RAINBOW 138 - 255 Color scrolling from slow to fast; rainbow effect
4 GOBO 0 - 255 Rotating gobos and speed adjustment
PRISMA 0 – 127 Setting prism; color temperature setting
5
TEMPERATURE
FILTER
128 - 255 Setting halogen lamp / discharge lamp effect
6 VELOCITÀ 0 - 255 Speed adjustment for X and Y axis
7 PAN 0-255 0° - 150°
8 TILT 0-255 0° - 110°
APPENDIX 2: DMX-512 channel settings
Projector
number
DMX starting
channel
Switch ON
1 1 1
2 9 1-4
3 17 1-5
4 25 1-4-5
5 33 1-6
6 41 1-4-6
7 49 1-5-6
8 57 1-4-5-6
PROEL S.p.A.
(World Headquarters – Factory)
Via alla Ruenia 37/43
64027 Sant’Omero (TE) – Italy
Tel. +39 0861 81241
Fax. +39 0861 887862
e-mail: [email protected]m
www.proelgroup.com
/