Printed in U.S.A.
Operator: Save these instructions for future use!
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
DESCRIPTION
These water valves provide a low cost system of zoned tem-
perature control wherever hot water is the heating medium. In
new construction, the heating piping system can be laid out to
produce any number of independent temperature controlled
zones by use of these valves.
In existing buildings, a variety of zone heating combinations can
be obtained, depending on the particular piping lay-outs. Each
zone requires one water valve and one thermostat, but only
one circulator is required for the entire system. New con-
struction properly piped, will not require flow control valves,
since the water valve itself performs this function.
Existing construction, where flow control valves have been
installed, will operate quite satisfactorily without removing the
existing flow control valves.
PRECAUTIONS
This zone valve motor is intended for use with a low voltage
system; do not use this zone valve with a millivolt or line voltage
system. If in doubt about whether your wiring is millivolt, line or
low voltage, have it inspected by a qualified heating contractor
or electrician.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical codes and
ordinances.
To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.
To prevent injuries from scalding always drain system
before unlatching valve assembly from body.
INSTALLATION INSTRUCTIONS
TYPE 1311
HYDRONIC ZONE VALVES
(3 WIRE)
The schematic shows the valve in the closed position. As the
thermostat calls for heat, the valve motor is energized and
begins to open the valve. Soon thereafter side “A” of motor
switch makes with the holding contacts. This contact provides a
holding circuit to prevent the valve from stopping part way
through its cycle if the thermostat is changed to the satisfied
Do not use on circuits exceeding specified voltages.
Higher voltages will damage control and could cause
shock or fire hazard.
SPECIFICATIONS
All guarantees are void if these specifications are exceeded.
Maximum water temperature: 240°F (115°C)
Maximum system pressure: 50 PSI
Differential across valve: 15 PSI
Electrical Rating:
Valve Motor: 25 VAC (.40 Amp.)
Auxiliary Contacts: Do not exceed 2.0 Amp. at 25 VAC
(Terminals 2 and 3)
Timing: Approximately 45 seconds from full open to full close
or full close to full open.
Friction loss equivalents:
3/4" valve – 2-1/2 ft. copper tubing
1" valves – 4 ft. copper tubing
1-1/4" valves – 7 ft. copper tubing
PRINCIPLE OF OPERATION
position. Just before the valve reaches the full-open position,
side “B” of motor switch closes (providing a low voltage auxiliary
circuit for starting burner and/or circulator). The motor stops with
the valve in the open position when side “A” of motor switch
breaks the holding contact. (Completing a circuit through con-
tact “6” and the thermostat anticipator.)
PART NO. 37-5421B
Replaces 37-5421A
9812
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123
(314) 577-1300, Fax (314) 577-1517
9999 HWY. 48, MARKHAM, ONT. L3P 3J3
(905) 475-4653, FAX (905) 475-4625
CAUTION
!
CAUTION
!
WARNING
!
WHITE-RODGERS
2
PRINCIPLE OF OPERATION (Continued)
When thermostat is satisfied, the valve motor is again ener-
gized. Just after the valve starts to close, side “A” of motor switch
makes with holding contact providing a holding circuit. The side
“B” of motor switch opens (breaking auxiliary circuit), and side
“A” of motor switch makes with contact “4” then breaks the
holding circuit stopping the valve in the closed position. (Fig. 2)
The contact arrangement is constructed so that when the shaft
of the motor revolves 90° a new set of stationary contacts makes
while the old set breaks. (Fig. 1)
NOTE: To check motor operation without thermostat
connected, jumper 4 to 5 to open valve; jumper
5 to 6 to close valve.
MOTOR SHAFT:
Revolves in 90° intervals
with each thermostat cycle.
STATIONARY CONTACTS
(TERMINALS 2 & 3)
STATIONARY CONTACTS
(TERMINALS 2 , 6 & COM.)
JUMPER WIRES
NOTE: INTERNAL PARTS AND
WIRING OF WATER VALVE.
COMMON
2
6
4
3
2
2
ROTATING BOARDS:
Each Board makes/breaks
1 set of contacts with each
90° revolution of motor
shaft on thermostat
demand.
▼
▼
▼
▼
▼
▼
▼
▼
▼
▼
▼
▼
▼
▼
▼
Use only silicone grease, water, or soap suds on O-ring
or Valve Body to facilitate assembly. Use of vaseline or
any petroleum grease or oil will cause O-ring to deterio-
rate.
Be sure that bayonet lock securely latches mounting
plate to body. Failure to do so could allow valve head
to separate from body and result in scalding injuries
and/or water damage.
1. Remove body assembly only from shipping carton. Valve
head and stem should be left in carton at this time for
protective purposes. Do not assemble head to body before
attaching body into line.
2. Mount the valve body in the line in any desired position
except upside down. CAUTION: Provide the necessary
clearances for turning valve head sideways when assem-
bling it to valve body (see fig. 3). Note that terminal end of
valve head requires more clearance.
3. Be sure that any excess solder, flux, or other foreign matter
is thoroughly removed from the valve bore.
4. With valve body mounted in the line, remove the head
assembly from the carton, and carefully wipe stem with a soft
cloth to remove any dust or grit.
5. The valve head may now be assembled to the valve body.
With valve head positioned as shown in figure 5, insert valve
stem into valve bore, push downward, and turn valve head
until it locks to valve body.
6. Support piping with a pipe hanger on each side of valve. The
valve is now ready to be wired.
ALL GUARANTEES ARE VOID IF THE VALVE IS NOT ASSEMBLED ACCORDING TO THESE INSTRUCTIONS.
INSTALLATION
The two most commonly used piping systems are
shown below. Plan 1 is popular for new installations,
while plan 2 is frequently used for converting two-pipe
systems.
This valve does not seal completely. A small amount of
leakage through valve is permitted. The amount de-
pends on valve size and pressure differential across
closed valve. Do not use if your application requires
complete seal off. Maximum leakage at rated differen-
tial is two, four or six gal. per hour for 3/4", 1" or 1-1/4"
valves, respectively.
729
PLAN 1
Water valves installed at the boiler
header to provide a separate sup-
ply to each zone.
PLAN 2
A common main supplies all
zones, with a water valve installed
on the riser to each zone.
Fig. 3
Fig. 4
PIPING
▼
TRANSFORMER
INTERNAL
WIRING
EXTERNAL
WIRING
MOTOR
ANTIC.
SATISFIED
CALL FOR
HEAT
HOLDING
CONTACT
SIDE “A”
OPEN
POSITION
WATER VALVE
THERMOSTAT
TO AUXILIARY CIRCUIT
FOR OPERATING BURNER
AND/OR CIRCULATOR.
(NOTE: IF SAME TRANS-
FORMER POWERS BOTH
THE AUXILIARY CIRCUIT
AND THE WATER VALVE,
CONNECT AUXILIARY CIR-
CUIT TO TERMINALS 1 AND
3 INSTEAD OF 2 AND 3.)
SIDE “B”
OPEN
POSITION
2
3
6
5
4
LINE
▼
▼
▼
▼
▼
▼
▼
CLOSED
POSITION
SIDE “A” OF
MOTOR SWITCH
SIDE “B” OF
MOTOR SWITCH
▼
1
4
6
5
STATIONARY CONTACTS
(TERMINALS 2, 4 & COM.)
(Valve is shown in the open position)
Fig. 1
Fig. 2
SCHEMATIC OF VALVE
CAUTION
!
CAUTION
!
3
F
F
T
T
V1
V2
1
2
3
4
56
4
56
4
56
4
56
1
2
3
452
6
1
2
3
452
6 1
2
3
452
6 1
2
3
452
6
To prevent injuries from scalding always drain system
before unlatching valve assembly from body.
▼
▼
▼
▼
2-3/4" MINIMUM
CLEARANCE
2" MINIMUM
CLEARANCE
VALVE
HEAD
STEM
BODY
Fig. 5
DIAGRAM FOR SYSTEMS WHERE BURNER AND
CIRCULATOR OPERATION IS INDEPENDENT OF
THERMOSTAT
Fig. 6 Using Type 1311 Zone Valve
T2
T1-V1
V2-L1
Z-L2
MUST BE N.E.C.
CLASS 1 WIRING
MUST BE
N.E.C. CLASS 1
WIRING
CIRCULATOR
MOTOR
1
2
3
{
TO ZONE
VALVES
TO 24 VOLT
GAS VALVE
YELLOW
HIGH LIMIT
TYPE 8A02A-1
CIRCULATOR MOTOR
HIGH LIMIT
RELAY CONTACTS
(24V OR 750 MV)
TRANSFORMER
RELAY COIL
WHITE
BLACK
WHITE
ORANGE
RELAY
CONTACTS
(LINE
VOLTAGE)
BURNER
MOTOR
IGNITION
TRANS.
TYPE 668 OIL
BURNER CONTROL
N
LINE
HOT
BLACK
TYPE 8A03A-2
ORANGE
V1
V2
TH
TH PG
PG
3
2
1
TYPE 8A03A-2
HIGH LIMIT
MUST BE N.E.C.
CLASS 1 WIRING
750 MV
GAS VALVE
1
2
3
}
TO ZONE VALVES
Alternate Wiring for using
750 Mv. Gas Valve
Alternate Connections
For Type 8A02A Relay
Fig. 7 Diagram
for Oil-fired
System using
8A03A-2
24 VAC
GAS VALVE
HIGH LIMIT
1
3
MUST BE N.E.C.
CLASS 1 WIRING
Fig. 7a Diagram for
Gas-Fired System
All wiring should be done according to local and national electrical codes
Do not attempt to wire two or more zone valves in
parallel to operate from a single thermostat. (If valves
are wired in parallel, the motors may run continuously,
due to feedback between the motor holding circuits.)
For best connections, use #18 Thermostat wire. #16 will also
work satisfactorily.
Make connections to screw terminals according to wiring dia-
gram.
NOTE: To check motor operation without thermostat con-
nected, jumper 4 to 5 to open valve; jumper 5 to 6 to close
valve.
If the boiler manufacturer recommends a wiring diagram, follow
his instructions. If none are available, the following diagrams
show suggested circuits for Type 1311 Water Valves in conjunc-
tion with other W-R controls.
A 40 VA transformer will handle up to four (4) water valves. A 20
VA transformer will handle up to two (2) water valves.
Clearances required for assembling valve head to valve body.
4
56
4
56
4
56
4
56
4
56
1
2
3
452
6
1
2
3
452
6
1
2
3
452
61
2
3
452
61
2
3
452
6
ADDITIONAL
ZONES
HOT
LINE
N
TRANSFORMER
DIAGRAM FOR SYSTEMS WHERE INTERNAL TRANSFORMER OF RELAY CONTROL SUPPLIES POWER
FOR ZONE VALVES
WIRING
TYPE 956
FLAME DETECTOR
HOT
LINE
N
750 MV
POWER
GENERATOR
CAUTION
!
CAUTION
!
4
1 2 L L
1
B2
C1 C2
T
2
B1
T
FD
FD
1
B2
C1 C2
2
B1
FD
T
T1T2
1
B2
C1 C2
2
B1
C1
B1 B2
C2
T1
T2
1 2
4
56
4
56
4
56
4
56
4
56
1
2
3
452
6
1
2
3
452
6
1
2
3
452
61
2
3
452
61
2
3
452
6
DIAGRAM FOR SYSTEMS WHERE INTERNAL TRANSFORMER OF RELAY-HOT WATER CONTROL
SUPPLIES POWER FOR ZONE VALVES
1
V2
C1 C2
T1
2
V1
T2
T3
4
56
4
56
4
56
4
56
4
56
1
2
3
452
6
1
2
3
452
6
1
2
3
452
61
2
3
452
61
2
3
452
6
1
V2
C1 C2
T1
2
V1
T2
Z
B
V3
W
CIRCULATOR
MOTOR
3
5
1
}
TO ZONE
VALVES
TO 24 VAC
GAS VALVE
Alternate Connections
For Type 8F42A
N
LINE
HOT
DIAGRAM FOR SYSTEMS WHERE EXTERNAL TRANSFORMER REQUIRED FOR POWERING ZONE
Fig. 10
OPEN
1
V2
C1 C2
T1
2
V1
T2
Z
3
5
1
}
TO ZONE
VALVES
TO 24 VAC
GAS VALVE
Alternate Connections
For Type 8F43A
TYPE 8F43A
CIRCULATOR
MOTOR
TYPE 8F42A
TO ZONE
VALVES
2
3
{
CIRCULATOR
MOTOR
TO LOW VOLTAGE
GAS VALVE
TYPE 842A-16
HOT
LINE
N
ADDITIONAL
ZONES
Fig. 8 Diagram for Gas-Fired
System using 842A-16
N
LINE
HOT
WIRING – Continued
power is resumed, valve will automatically return to command of
room thermostat.
Use manual operator only in case of power failure, or for testing
system prior to wiring. If power fails, valve may be in either
“Open” or “Closed” position.
If in “Open” position, valve will remain open until power is
resumed.
If in “Closed” position, valve may be opened by turning dial
clockwise with your thumb until word “Open” appears. When
MANUAL OPERATION
2
3
{
TO ZONE
VALVES
TYPE 8B42A
OR 8B43A
N
LINE
HOT
CIRCULATOR
MOTOR
BURNER
MOTOR
IGN.
TRANS.
Alternate Connections
For Type 8B42A or 8B43A
ADDITIONAL
ZONES
TRANSFORMER
TYPE 842A OR
843A
CIRCULATOR
MOTOR
BURNER
CONTROL
HOT
LINE
N
THERM
1
6
3
4
5
2
TYPE 829A RELAY
Alternate Connections
For Type 829A Relay
TO GAS VALVE AND
TRANSFORMER OR
OIL BURNER
CONTROL
CIRCULATOR
MOTOR
HOT
LINE
N
TYPE 6C92 OR 6C93
OIL BURNER
HOT WATER CONTROL
TYPE 956
FLAME DETECTOR
HOT
LINE
N
BURNER
MOTOR
CIRCULATOR
MOTOR
2
3
{
TO ZONE
VALVES
IGN.
TRANS.
Alternate Connections
For Type 6C92 or 6C93
IGN.
TRANS.
HOT
LINE
N
TYPE 692 OR 693
OIL BURNER
HOT WATER CONTROL
TYPE 956
FLAME DETECTOR
BURNER
MOTOR
CIRCULATOR
MOTOR
2
3
{
TO ZONE
VALVES
Alternate Connections
For Type 692 or 693
HOT
LINE
N
CIRCULATOR
MOTOR
TO GAS VALVE
AND TRANSFORMER
OR OIL BURNER
CONTROL
Alternate Connections
For Type 809A Relay
TYPE 809 RELAY
2
3
{
TO ZONE
VALVES
Fig. 9 Diagram for Gas-Fired System using
842A-1 or 843A-1
Page is loading ...
Page is loading ...
Page is loading ...
4
1
B2
C1 C2
T
2
B1
T
FD
FD
1 2 L L
T1T2
1
B2
C1 C2
2
B1
C1
B1 B2
C2
T1
T2
1 2
4
56
4
56
4
56
4
56
4
56
1
2
3
452
6
1
2
3
452
6
1
2
3
452
61
2
3
452
61
2
3
452
6
1
V2
C1 C2
T1
2
V1
T2
T3
4
56
4
56
4
56
4
56
4
56
1
2
3
452
6
1
2
3
452
6
1
2
3
452
61
2
3
452
61
2
3
452
6
1
V2
C1 C2
T1
2
V1
T2
Z
B
V3
W
MOTEUR DU
CIRCULATEUR
3
5
1
}
VERS LE ROBINET À
GAZ DE 24 V C.A.
Câblage pour type 8F42A
SCHÉMA POUR LES SYSTÈMES QUI NÉCESSITENT UN TRANSFORMATEUR EXTERNE POUR ALIMENTER LES ROBINETS DE
ZONE
1
V2
C1 C2
T1
2
V1
T2
Z
3
5
1
}
Câblage pour type 8F43A
TYPE 8F43A
MOTEUR DU
CIRCULATEUR
TYPE 8F42A
MOTEUR DU
CIRCULATEUR
VERS LE ROBINET
À GAZ À BASSE
TENSION
TYPE 842A-16
ZONES
SUPPLÉMENTAIRES
ZONES
SUPPLÉMENTAIRES
TRANSFORMATEUR
MOTEUR DU
BRÛLEUR
COMMANDE DU
BRÛLEUR
TYPE 842A OU 843A
TYPE 8F42A
OU 8B43A
2
3
{
MOTEUR DU
BRÛLEUR
MOTEUR DU
CIRCULATEUR
Câblage pour type
8B42A ou 8B43A
{
THERM
1
6
3
4
5
2
2
3
SOUS TENSION
CIRCUIT
N
1
B2
C1 C2
2
B1
FD
T
DÉTECTEUR DE
FLAMME TYPE 956
MOTEUR DU
BRÛLEUR
MOTEUR DU
CIRCULATEUR
2
3
{
2
3
RELAIS TYPE 809
MOTEUR DU
CIRCULATEUR
VERS LE ROBINET À GAZ ET
LE TRANSFORMATEUR OU
VERS LA COMMANDE DU
BRÛLEUR À MAZOUT
DÉTECTEUR DE
FLAMME TYPE 956
MOTEUR DU
BRÛLEUR
MOTEUR DU
CIRCULATEUR
Fig. 9 Schéma pour un système alimenté à gaz
et doté d’un 842A-1 ou d’un 843A-1
Servez-vous de l’actionneur manuel seulement en cas de
panne de courant ou dans le but de mettre le système à l’essai
avant d’en effectuer le câblage. En cas de panne de courant, le
robinet sera soit ouvert, soit fermé.
S’il est ouvert, il restera ainsi jusqu’à ce que le courant soit
rétabli.
S’il est fermé, vous pouvez l’ouvrir en tournant l’actionneur avec
le pouce de façon à exposer le mot « OPEN ». Une fois le
FONCTIONNEMENT MANUEL
CÂBLAGE (suite)
VERS LA VALVE DE GAZ
ET LE TRANSFORMATEUR
OU VERS LA COMMANDE
DU BRULEUR A MAZOUT
MOTEUR DU
BRULEUR
SCHÉMA POUR LES SYSTÈMES DONT LE TRANSFORMATEUR INTERNE DE LA COMMANDE D’EAU CHAUDE À RELAIS
ALIMENTE LES ROBINETS DE ZONE
SOUS TENSION
CIRCUIT
N
VERS LES
ROBINETS DE
ZONE
VERS LE ROBINET À
GAZ DE 24 V C.A.
N
CIRCUIT
SOUS TENSION
VERS LES ROBINETS
DE ZONE
N
CIRCUIT
SOUS TENSION
Fig. 8 Schéma pour un
système alimenté à gaz et
doté d’un 842A-16
N
CIRCUIT
SOUS TENSION
SOUS TENSION
CIRCUIT
N
TRANSFO
D’ALLUMAGE
RELAIS TYPE 829A-1
Câblage pour relais
de type 829A
SOUS TENSION
CIRCUIT
N
TRANSFO
D’ALLUMAGE
VERS LES
ROBINETS
DE ZONE
VERS LES
ROBINETS
DE ZONE
COMMANDE DE BRÛLEUR À
MAZOUT TYPE 692 OU
693 POUR SYSTÈMES À
L’EAU CHAUDE
COMMANDE DE BRÛLEUR
À MAZOUT
TYPE 6C92 OU 6C93 POUR
SYSTÈMES À L’EAU CHAUDE
TRANSFO
D’ALLUMAGE
Câblage pour un
relais de type 809A
SOUS TENSION
CIRCUIT
N
SOUS TENSION
CIRCUIT
N
{
2
3
VERS LES
ROBINETS
DE ZONE
Câblage pour type 692 ou 693
Câblage pour type
6C92 ou 6C93
courant rétabli, le robinet se remettra automatiquement sous la
commande du thermostat d’ambiance.
Fig. 10
OPEN
VERS LES
ROBINETS
DE ZONE
{
VERS LES
ROBINETS
DE ZONE
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Emerson 1311-102 User manual
- Category
- Thermostats
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Emerson 1311-102 Manuel utilisateur
Related papers
-
White Rodgers 1361-103 Operating instructions
-
Emerson 5C06 User manual
-
-
White-Rodgers White Rodgers 36J22 User manual
-
-
White Rodgers 5D51-35 User manual
-
-
-
Other documents
-
-
-
White Rodgers 1127-2 User manual
-
-
-
-
-
-
-