Yamaha MCR-042 Owner's manual

Page is loading ...

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place

-

away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the

following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other elec

trical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from co

ld to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit, which

may cause an electrical shock, fire, damage to this unit,

and/or personal injury.

5 Avoid installing this unit w

here foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

dama

ge to this unit, and/or personal injury.

– Containers with liquid in them,

as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

con

nections are complete.

8 Do not operate this unit upside-down.

It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp th

e plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must

be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

13 To prevent damage by lightning, keep the power cable

disconnec

ted from a wall outlet or this unit during a

lightning storm.

14 Do not attempt to modify or fix this

unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this un

it for long periods of time

(i.e. vacation), disconnect the AC power plug from the

wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set the system to off,

and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature change

s suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

w

arm. Turn the system off, then leave this unit alone for

cooling.

20 Install this unit near the wall outlet and where the AC

power

plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as

sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

– Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or

her mouth.

– If the batteries grow old, the effective operation range of

the r

emote control decreases considerably. If this happens,

replace the batteries with new one as soon as possible.

– Do not use old batteries together with new ones.

– Do not use different types of batteries (such as alkaline

and manganese batte

ries) together. Read the packaging

carefully as these different types of batteries may have the

same shape and color.

– Exhausted batteries may leak. If

the batteries have leaked,

dispose of them immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before

installing new batteries.

– If you plan not to use the unit for a long period of time,

r

emove the batteries from the unit. Otherwise, the batteries

will wear out, possibly resulting in a leakage of battery

liquid that may damage the unit.

– Do not throw away batteries with general house waste.

D

ispose of them correctly in accordance with your local

regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off by . In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SH

OCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace o

nly with the same or equivalent type.

There is a chance that placing this unit too close to a CRT-

ba

sed (Braun tube) TV set might impair picture color.

Should this happen, move this unit away from the TV set.

1 En

English

CONNECTIONS ........................................................2

Connecting the speakers and antenna ..........................2

Connecting the power cable...........................................2

Other connections..........................................................3

NAMES OF PARTS AND THEIR FUNCTIONS ........4

Top panel / Front panel..................................................4

Front panel display.........................................................4

Remote control...............................................................5

ADJUSTING THE CLOCK (OPTION MENU) ...........6

LISTENING TO YOUR iPod......................................7

Playing music from your iPod.........................................7

Using repeat/shuffle playback (remote control only)

......8

LISTENING TO CD AND USB DEVICES .................9

Listening to a CD............................................................9

Listening to a USB device............................................10

Using repeat/shuffle playback (remote control only)

....10

LISTENING TO MUSIC FROM YOUR Bluetooth

COMPONENT..........................................................11

Pairing this unit with your Bluetooth component ..........11

Listening to a Bluetooth compon

ent.............................12

Connecting an already-paired component via

Bluetooth

...12

Disconnecting a Bluetooth connection

.........................13

LISTENING TO FM STATIONS ..............................13

Selecting an FM station................................................13

Presetting FM stations (remote control only)

...............14

Selecting preset FM stations........................................15

LISTENING TO EXTERNAL SOURCES ................15

USEFUL FUNCTIONS ............................................16

Using the Option menu ................................................16

Using the sleep timer ...................................................16

Using the alarm function ..............................................17

Setting the alarm ..........................................................18

Operations while the alarm sound is playing................19

USING THE “DTA Controller” APPLICATION

FOR THE iPod touch/iPhone/iPad........................20

TROUBLESHOOTING ............................................21

NOTES ON DISCS AND USB DEVICES................24

SPECIFICATIONS...................................................

25

CONTENTS

• Play back music from external devices such as your iPod/iPhone/iPad, audio/data CDs, USB devices, or external devices

via the AUX jack, and listen to the FM.

•By the Bluetooth technology, you can enjoy clear sound without wire connections.

• Use your favorite music or a beep tone as an alarm. When the set time arrives, the music you select is played at the volume

that you specify, giving you the ideal start to your day (IntelliAlarm function).

•

By using the free “DTA Controller” application for the iPod touch/iPhone/iPad, you can control this unit

and take

advantage of more sophisticated alarm functionality (☞ P. 20).

• You can easily store and recall 30 of your favorite FM stations.

• Bass, middle, and treble can be adjusted to your taste.

 About this manual

• References to the iPod appearing in this manual also include the iPhone.

• If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will

focus on operation using the remote control.

• indicates precautions for use of the unit and its feature limitations.

• indicates supplementary explanations for better use.

 How to use the remote control  Replacing the battery in the remote control

Features

Supplied accessories

Dock coverFM antenna

(uses a CR2032 type

Lithium Battery)

Remote control Speaker cable

(1.5 m (4.9') x 2)

Within 6 m (20')

Battery insulation sheet:

Remove before using.

CR2032 type

Lithium Battery

While pushing the release tab

in direction , slide out the

battery holder in direction .

(at the end of this manual)

Additional information................................................i

2 En

Connect the speakers and antenna.

If FM reception is poor, try changing the height or direction or placement of the antenna to find a location that has better

reception.

If you use a commercially available outdoor antenna instead of the supplied antenna, reception may be better.

Do not connect this unit’s po

wer cable until you’ve finished connecting all cables.

When you’ve completed all connections, con

nect this unit’s power cable to an AC outlet.

CONNECTIONS

Connecting the speakers and antenna

Connecting the power cable

ANTENNA SPEAKERS

AUX IN

FM

Speakers

• You must peel off the insulation (covering) from the tip of the speaker cable to

expose the conductor.

• Check the connections; make sure that left and right (L, R) and polarity (red: +,

black: –) are connected correctly. If connections are incorrect, the sound will be

unnatural and the low frequencies may be insufficient. There might not be any

sound at all if connections are incorrect.

• Take care that the conductors of the speaker cable do not touch each other, and that

the conductors do not touch any other metal part. Such conditions can damage this

unit or the speakers.

• Use only the supplied speakers. Using other speakers may result in unnatural sound.

• If you’re using this unit nearby a CRT display and you notice distorted color or

noise in the display, move the speakers farther away from the display.

Twist the bare wires

tightly so the individual

strands are not splayed.

FM antenna

Be sure to stretch out the antenna.

To the AC

wall outlet

Rear panel

3 En

CONNECTIONS

English

 iPod

Connect your iPod to the iPod dock on the top panel. For details on compatible iPod models, refer to

“SPECIFICATIONS”

(P. 25)

.

 iPad

Connect your iPad to the front panel USB port. For details on compatible iPad models, refer to “SPECIFICATIONS” (P. 25).

 USB device

Connect your USB device to the USB port on the front panel. For details on playable files, refer to “NOTES ON DISCS AND

USB DEVICES” (P. 24).

 External devices

Using a commercially available 3.5 mm mini-plug cable, connect your external device to the AUX jack on the rear panel of

this unit.

Other connections

iPod dock

• Be sure to use a dock adaptor that is compatible with your iPod. If you do not use the adaptor or the

adaptor is not compatible, the connection could be loose or poor, which could cause damage to the

connector. For details on dock adaptor information, please visit Apple’s official website.

• If an iPod in a protective case is forcibly connected, the connector may be damaged. Remove the

protective case before connection.

• When the iPod is not in use, install the dock cover to protect the connector.

• Your iPod will be recharged while it is connected to the dock. However if USB is selected as the

audio source, the iPod will not be recharged.

• Your iPod can also play back music and charge while connected to the USB port. To do this, select

USB as the audio source (☞ P. 10) .

• You can remove the iPod during playback.

Dock

adaptor

Make sure to use a Dock Connector to USB Cable that is supplied with your iPad.

• When you turn the system on and set the audio source to USB, the iPad

connected to this unit will be recharged.

• You can remove the iPad during playback.

Stop playback before disconnecting the USB device.

When you turn the system on and set the audio source to USB, the USB device connected to this

unit will be recharged.

AUX IN

Rear panel

4 En

a iPod dock

Connect your iPod here (☞ P. 3, 6, 7).

Be sure to use a dock adaptor that is compatible with

your iPod

(☞ P. 3).

b Front panel display

The clock and other information is displayed here.

c Disc slot

Insert a CD here (☞ P. 9).

d (Power)

Press to turn the system on/off.

e USB port

Connect your USB device / iPod / iPhone / iPad here

(

☞

P. 3, 10).

f (Headphone jack)

Connect headphones here.

g SOURCE

Switch the audio source to be played.

Pressing this repeatedly will change the selection in the

following ord

er.

CD iPod

USB FM BT AUX back to CD

h VOLUME knob

Adjust the volume.

i Audio control buttons

Use these to operate the iPod/CD/USB device.

j PRESET /

Use these buttons to select a radio station that you’ve

stored (☞ P. 15).

k (Eject button)

Eject the CD (cannot be operated while the option menu

(☞ P. 16) is displayed).

a Alarm time

This indicates the alarm time (☞ P. 18).

b Repeat/shuffle indicator

Displays the playback mode (☞ P. 8, 10).

c Multi-function indicator

Displays various information, including the clock time,

information about the currently-playing track, and the

frequency of the radio station.

d Remote control signal receiver

Make sure that this sensor is not obstructed (☞ P. 1).

e Sleep indicator

Turns on if the sleep timer has been set (☞ P. 16).

f Alarm indicator

Turns on if the alarm has been set (☞ P. 18).

g Weekly alarm indicator

Shows alarm information specified using the free “DTA

Controller” application for the iPod touch/iPhone/iPad

(☞ P. 20).

NAMES OF PARTS AND THEIR FUNCTIONS

Top panel / Front panel

1

2

k

3

4 5 6 7 89 j

:

Play/Pause

:

Stop

/ :

Skip, Search backward/forward (press and hold

down)

Front panel display

~~~~~~

43

7

1 2

6 5

5 En

NAMES OF PARTS AND THEIR FUNCTIONS

English

a Remote control signal transmitter

b (Power)

Press to turn the system on/off.

c SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(☞ P. 16, 19).

d ALARM

Switch the alarm on/off (☞ P. 19).

e Source buttons

Switch the audio source to be played. If you press one of

these while the system is off, the system will

automatically turn on.

f MENU

Switch the iPod menu item / Return to the previous

menu (☞ P. 7).

g FOLDER / 

Switch the playback folder when playing music on data

CDs or USB devices (☞ P. 9, 10).

Select items or edit numerical

values (☞ P. 7, 16).

h ENTER

Confirm a selected item or value.

i Audio control buttons

Use these to operate the iPod/CD/USB device.

j (Repeat)/ (Shuffle)

Play music on an iPod, CD or USB device in repeat/

shuffle mode (☞ P. 8, 10).

k TUNING /

Tune the radio (☞ P. 13, 14).

l PRESET /

Select a FM station that you stored (☞ P. 14, 15).

m MEMORY

Store a FM station (☞ P. 14).

n MUTE

Mute or unmute the sound.

o VOLUME + / –

Adjust the volume.

p DISPLAY

Switch the information shown in the front panel display

(☞ P. 6, 7, 9, 10,

13).

q +10

Skip ten songs ahead of the currently-playing song.

When playing a data CD or a USB device, this button

skips ten

songs within the current folder.

r OPTION

Display the option menu (☞ P. 16).

Remote control

3

4

5

6

9

j

k

l

m

1

8

2

p

q

r

n

o

7

iPod control buttons

:

Stop

:

Play/Pause

/ :

Skip, Search backward/forward (press and hold

down)

6 En

You’ll use the option menu (☞ P. 16) to set this unit’s date and time.

 To copy the time from your iPod

 Setting the clock manually

ADJUSTING THE CLOCK (OPTION MENU)

1 Press OPTION.

The option menu will appear.

2 Press /  to select “CLOCK SET,” and then

press ENTER.

The display will indicate “CLOCK YEAR,” and the

numerical value to be set will blink.

3 Set your iPod in the iPod dock (☞ P. 3).

The time will be copied from your iPod to this unit.

Press ENT

ER to confirm the items in the order of

year month day hour minute.

When clock setting has finished,

the display will indicate

“Completed!”

• By pressing DISPLAY you can select the time format (12-

hour / 24-hour).

• The time will not be copied if the iPod is alrea

dy connected or

if the audio source is set to USB.

The time settings will be reset if the unit

remains unpowered for

about one hour.

1 Press OPTION.

The option menu will appear.

2 Press /  to select “CLOCK SET,” and then

press ENTER.

The display will indicate “CLOCK YEAR,” and the

numerical value to be set will blink.

3 Set the date and time.

Press ▲/▼ to edit each numerical value, and then press

ENTER to confirm the setting.

Set the items in the order of year month day

hour minute.

When clock setting has finished,

the display will indicate

“Completed!”

The clock will be set to 0 second the moment you

complete the clock settings.

• While making these settings, you can press DISPLAY to

select the time format (12-hour / 24-hour).

• If you decide to cancel witho

ut changing the setting, press

OPTION before confirming the change.

The time settings will be reset if the unit

remains unpowered for

about one hour.

Dock adaptor

(☞ P. 3)

3

4

2

1

26

Apr

Jan Feb Mar Apr May Jun

January February March April May June

Jul Aug Sep Oct Nov Dec

July August September October November December

1

32

15:30

iPod

Display (24-hour) when the system is on

Display (24-hour) when the system is off (POWER SAVING: NORMAL)

Clock display

7 En

English

• For details on compatible iPod models, refer to “SPECIFICATIONS” (P. 25).

• Your iPod can also play back music and rechar

ge while connected to the USB port (☞ P. 10).

 iPod menu operations (remote control only)

You can use the remote control to operate your iPod.

 Display information (remote control only)

If you press DISPLAY on the remote control while a song is playing or paused, the information shown on the front panel

display will be switched in the following order.

LISTENING TO YOUR iPod

Playing music from your iPod

1 Press the iPod source button to switch the

audio source to iPod.

2 Set your iPod in the iPod dock (☞ P. 3 ).

3 Play the iPod.

Playback can be controlled with either the remote

control, iPod or the front panel on this unit (☞ P.

4, 5).

• Performing the following operations will automatically switch the

audio source to iPod and start playback even if this unit is system-

off.

− Co

nnect your iPod in the playback state to the iPod dock.

− Play back the connec

ted iPod.

In some cases, the audio source might

not switch automatically

if the audio source is USB or if there is currently a Bluetooth

connection.

• If USB is selected as the audio source, the iPod will not be

rechar

ged.

• You can remove the iPod

during playback.

• If iPod is selected as the audio source, thi

s unit will automatically

turn the system off when 60 minutes have elapsed without a

device being connected to the iPod dock nor any operation

performed.

1

2

Dock adaptor

(☞ P. 3)

MENU:

Switch menu items / Return to the previous menu

 / :

Move between items in the menu

ENTER:

Confirm

Elapsed song playback time

Song name

Album name

Artist name

LISTENING TO YOUR iPod

8 En

The playback status is shown by the repeat/shuffle indicator in the front panel display.

Repeat playback Shuffle playback

The operation or display of repeat/shuffle may differ, depending on the type or software version of iPod used.

Using repeat/shuffle playback (remote control only)

Press (repeat) repeatedly to

select one of the following

playback modes.

No display: Off

: One

:

All

Press (shuffle) repeatedly to

select one of the following

playback modes.

No display: Off

: Songs

: Albums

9 En

English

 Skipping folders (remote control only)

 Display information (remote control only)

LISTENING TO CD AND USB DEVICES

The unit will operate as follows when playing back tracks/files on CD/USB devices.

• If the CD/USB device being played is stopped

, the track that you listened will start playback from the beginning of the

track the next time you play.

• If you press while playback is stopped, tracks will

play as follows the next time playback begins:

− Audio CD: Play from the first track of the CD.

−

Data CD*/USB device:

Play from the first track of the folder contains the track you listened to last time.

• This unit automatically turns off the system if no operation has been performed for 60 minutes after CD/USB device

playback is stopped.

* “Data CD” is a CD that contains MP3/WMA files.

For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (P. 24).

Listening to a CD

1 Press the CD source button to switch the

audio source to CD.

If a CD is already inserted, playback will start.

2 Insert a CD into the disc slot.

Playback starts automatically.

Playback can be controlled with either the remote

control,

or the front panel on this unit (☞ P.

4, 5).

Insert the CD with the label side facing upward.

Folders and files on a data CD are played in alphabetical order.

While a data CD is playing, you can use the remote control’s FOLDER ▲/▼

buttons to select the folder.

The folder number (only for a data CD) or

the song/file number is shown for

several seconds when starting playback or skipping tracks.

If you press

DISPLAY

on the remote control while a song is playing or paused, the

information shown on the front panel display will be switched in the following order.

1

2

Audio CD

Elapsed song playback time

Remaining song playback time

Song name*

Album name*

Artist name*

Data CD

Elapsed song playback time

Song name*

Album name*

Artist name*

File name

Folder name

* Shown only if this data is included in the song.

LISTENING TO CD AND USB DEVICES

10 En

 Skipping folders (remote control only)

 Display information (remote control only)

The playback status is shown by the repeat/shuffle indicator in the front panel display.

Repeat playback Shuffle playback

Listening to a USB device

1 Press the USB source button to switch the

audio source to USB.

If a USB device is already connected, playback will start.

2 Connect a USB device to the USB port.

Playback starts automatically.

Playback can be controlled using

either the remote control,

the front panel on this unit, or the USB device (

☞

P. 4, 5).

• Folders and files will play in the order in which they were written.

• Your iPod/iPhone/iPad can also play bac

k music and charge while

connected to the USB port.

Stop playback before disconnecting the USB device.

While a USB device is playing, you can use the remote control’s FOLDER ▲/▼

buttons to select the folder.

The folder/file number is shown for several

seconds when starting playback or

skipping tracks.

If you press

DISPLAY

on the remote control while a song is playing or paused, the

information shown on the front panel display will be switched in the following order

.

Using repeat/shuffle playback (remote control only)

1

2

Elapsed song playback time

Song name*

Album name*

Artist name*

File name

Folder name

* Shown only if this data is included in the song.

Press (repeat) repeatedly to

select one of the following

playback modes.

No display: Repeat mode off

: 1 track

: All tracks within the folder (data CD/

USB device only)

:

All tracks

Press (shuffle) repeatedly to

select one of the following

playback modes.

No display: Shuffle mode off

: All tracks within the folder (data CD/

USB device only)

: All tracks

11 En

English

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth component (mobile

phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth component.

Pairing is an operation that registers the

communicating component (subsequently called “the other component”) with this

unit. You’ll need to perform the pairing operation the first time you use your Bluetooth component with this unit, or if the

pairing settings have been deleted. Once pairing has been completed, subsequent reconnection will be easy even after the

Bluetooth connection is disconnected. If pairing is not successful, refer to the item “Bluetooth” in “TROUBLESHOOTING”

(P. 21).

• This unit can be paired with up to eight other components. When pairing with the ninth component has succeeded, pairing data for the

component with the oldest connection date will be deleted.

• If this unit is connected via B

luetooth to another component, hold down on the remote control or SOURCE on this unit to disconnect

the Blu

etooth connection before you perform the pairing operation.

 If using an iPod touch/iPhone/iPad

 If using other than an iPod touch/iPhone/iPad

LISTENING TO MUSIC FROM YOUR

Bluetooth

COMPONENT

Pairing this unit with your Bluetooth component

1 Press the source button to switch the audio

source to B

luetooth.

2 On your iPod touch/iPhone/iPad, turn

[Settings]

[General] [Bluetooth] on.

The Bluetooth connection list will appear in [Devices].

(This procedure or display

may differ depending on the

type of your iPod touch/iPhone/iPad.)

3 From the Bluetooth connection list of the other

component, choose this unit (MCR-B142

Ya m a h a ).

When pairing has been completed, your iPod touch/

iPhone/iPad will indicate “Connected”.

The front panel display of this unit will indicate “Pairing

OK” and show the name of the other component, and the

Bluetooth indicator will light.

1 Press the source button to switch the audio

source to B

luetooth.

2 Perform Bluetooth pairing on the other

component.

For details refer to the owner’s manual of the other

component.

3 From the Bluetooth connection list of the other

component, choose this unit (MCR-B142

Ya m a h a ).

When pairing has been completed, the front panel display

of this unit will indicate “Pairing OK”.

If you are asked to enter a password, enter the numerals “0000”.

15:30



BT

DTA iPhone

1

3

1

15:30



BT

Pairing OK

3

LISTENING TO MUSIC FROM YOUR Bluetooth COMPONENT

12 En

Once pairing has been completed, connecting a Bluetooth will be easy the next time.

 Connecting from this unit

 Connecting from the other component

Listening to a Bluetooth component

1 Press the source button to switch the audio

source to Bluetoo

th.

2 Connect this unit and your other component

via Bluetooth.

3 Play back music from your Bluetooth

component.

Take care that the volume setting of this unit is not too high. We

recommend that you adjust the volume on the other component.

• If you connect via Blu

etooth from your other component and play

back music while this unit is turned the system off, this unit will

automatically turn the system on.

• If you disconnect the Bl

uetooth connection from your other

component while the audio source is set to Bluetooth, this unit

will automatically turn the system off.

•If Blu

etooth is selected as the audio source, this unit will

automatically turn the system off when 60 minutes have elapsed

without any Bluetooth connection nor any operation performed.

Connecting an already-paired component via Bluetooth

Press the source button to switch the audio

source to B

luetooth.

The Bluetooth indicator will blink in the front panel display;

this unit will search for the other component that was most

recently connected via Bluetooth, and will then establish a

connection (You must first turn on the Bluetooth setting of

the other component).

When the Bluetooth connection

has been established, the

Bluetooth indicator will light, and the name of the other

component will be displayed.

Yamaha does not guarantee all connections between this unit and

Bluetooth component.

1 In the Bluetooth settings of the other component, turn Bluetooth on.

2

From the

Bluetooth

connection list of the other component, choose this unit (MCR-B142 Yamaha).

The Bluetooth connection will be established, and the front panel display of this unit will indicate the name of the other

component.

Bluetooth connections cannot be established from the other component when this unit is in power-conservation. Turn the system on.

15:30



15:30



BT

DTA iPhone

13 En

LISTENING TO FM STATIONS

English

If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be

disconnected.

• Hold down on the remote control or SOURCE on this unit.

• Turn the system off.

• Turn off the Bluetooth setting of the

other component.

When you connect an iPod touch/iPhone/iPad via Bluetooth, the Bluetooth connection may be disconnected if you switch the audio source to

iPod or USB while an iPod/iPhone/iPad is connected.

To listen to the FM station, connect the antenna as described in “Connecting the speakers and antenna” (P. 2).

 Display information (remote control only)

If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the

following order.

Displaying Radio Data System information

If you press DISPLA

Y on the remote control while Radio Data System information is being received, the information shown

on the front panel display will be switched in the following order.

If the signal transmission of the Radio Data System station is too weak, this unit may not be

able to receive Radio Data System information completely. In particular, RT (Radio Text)

information uses a lot of bandwidth, so it may be less available compared to other types of

information.

Disconnecting a Bluetooth connection

LISTENING TO FM STATIONS

Selecting an FM station

1 Press the RADIO source button to switch the

audio source to FM.

2 Tune FM stations

Automatic tuning: Press and hold TUNING / .

Manual tuning: Press TUNING / repeatedly.

If you tune to a station manually while receiving FM, the sound

will be monaural.

1

2

Preset number and frequency Reception status*

* Example of reception status indication.

TUNED/STEREO: A strong FM stereo broadcast is being received.

TUNED/MONO: A monaural FM broadcast is being received (even if the FM

broadcast is stereo, reception will be monaural if the signal is weak).

Not TUNED: No broadcast is being received.

PS (Program Service)

PTY (Program Type)

RT (Radio Text)

CT (Clock Time)

Reception status

Preset number and frequency

LISTENING TO FM STATIONS

14 En

Use the preset function to store your favorite 30 stations.

 Auto preset

This method tunes automatically, and automatically presets only the stations that have good reception.

 Manual preset

 Deleting a stored preset (Option menu)

Presetting FM stations (remote control only)

1 Press and hold down MEMORY.

“AUTO PRESET” will appear and “Press MEMORY”

will blink.

2 Press MEMORY.

Auto preset will begin.

When presetting has finished,

the display will indicate

“Completed!”.

When you perform auto preset, all stored stations are cleared

and the new stations are stored.

If you want to stop auto preset before it is completed, press .

1 Press TUNING / to tune a station that

you want to preset.

2 Press MEMORY.

The display will indicate “PRESET MEMORY,” and the

preset number will blink.

3 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a

station has already

been stored, it will be overwritten by the new station.

4 Press MEMORY.

When presetting has finished, the display will indicate

“Completed!”.

1 Press OPTION.

The option menu will appear.

2 Press  /  to select PRESET DELETE, and

then press ENTER.

3 Press  /  to select the preset number that

you want to delete.

If you want to cancel the deleting, press OPTION.

4 Press ENTER to complete the operation.

When deleting has finished, the display will indicate

“Deleted!”.

5 Press OPTION to exit the option menu.

AUTO PRESET



Press MEMORY

1 2

PRESETMEMORY

FM0187.50MHz

3

1

42

1 5

3 42

15 En

LISTENING TO EXTERNAL SOURCES

English

Selecting preset FM stations

1 Press the RADIO source button to switch the

audio source to FM

.

2 Press PRESET / to select the FM station

that you want to hear.

You can only select presets that have been stored.

LISTENING TO EXTERNAL SOURCES

1 Using a commercially available 3.5 mm mini-

plug cable, connect your external device to the

AUX jack on the rear panel of this unit.

• Turn off the system before connecting the audio cable.

• Turn down the volume of the unit and your external audio

dev

ice before connection.

2 Press to turn the system on.

3 Press the AUX source button to switch the

audio source to AUX.

4 Start playback on the connected external

audio device.

1

2

AUX IN

1

2

Rear panel

3

16 En

When you press

OPTION

, the option menu will appear in the front panel display, allowing you to make the following settings.

(eject button) cannot be operated while the option menu is displayed.

Default setting

 Procedure for settings

When the specified time has elapsed, the system will turn off automatically.

USEFUL FUNCTIONS

Using the Option menu

Option menu Setting or range See page

PRESET DELETE Deletes a stored preset (shown only

if the audio source is FM).

14

DIMMER Adjusts the brightness of the front panel display (1*: bright, 2: medium, 3: dim).

–

EQ LOW Adjusts the tonal character (low frequencies) (–10 - 0* - +10 dB).

–

EQ MID Adjusts the tonal character (mid frequencies) (–10 - 0* - +10 dB).

–

EQ HIGH Adjusts the tonal character (high frequencies) (–10 - 0* - +10 dB).

–

BALANCE Adjusts the volume balance of the left and right speakers (L+10 - CENTER* - R+10).

–

POWER SAVING Switches the system-off state

–

AUTO POWER

OFF

You can specify the time after which the system will turn off automatically.

If no operation occurs for the duration you specify, the system will turn off automatically

(

TIME 12H

*: 12 hours,

TIME 8H

: 8 hours,

TIME 4H

: 4 hours,

OFF

: the system will not turn off).

–

CLOCK SET Sets the date and time.

6

ALARM SET Sets the alarm.

18

1 Press OPTION.

The option menu will appear.

2 Press  /  to select the menu item that you

want to set, and then press ENTER.

3 Press  /  to edit the setting, and then press

ENTER to confirm the setting.

If you want to continue making other settings, repeat the

procedure from step .

4 Press OPTION to exit the option menu.

If you decide to cancel without changing the setting, press

OPTION before confirming the change.

Using the sleep timer

Press SNOOZE/SLEEP repeatedly to specify the

time after which the system will turn off.

You can specify 30, 60, 90, 120 or OFF.

When you select a time, the sleep timer is turned on, and the

sleep indicator ( ) is shown in the front panel display.

If you press SNOOZE/SLEEP while the sleep timer is activated,

the sleep timer setting will be canceled.

NORMAL: Show the clock

An iPod can be charged in the iPod Dock, and the alarm will operate

ECO*:

(power saving mode)

No clock display

An iPod can be charged in the iPod Dock, but the alarm will not operate

1

3

4

2

Press repeatedly

17 En

USEFUL FUNCTIONS

English

The unit includes an alarm function (IntelliAlarm) that plays back audio sources or a set of beep (internal alarm sound) at the

set time using a variety of different methods. The alarm function has the following features.

 3 types of alarms

Select from 3 alarm types, combining music and beep sounds.

 Various audio sources

You can choose from iPod, audio CD, data CD, USB device, or FM. The following playback methods can also be selected

depending on the audio source:

* For information on creating a playlist, refer to the instructions for your iPod or iTunes.

Snooze

The snooze function can be enabled to replay the alarm after 5 minutes (☞ P. 19).

Using the alarm function

SOURCE+BEEP

The selected audio source and the beep sound are pla

yed at the set time.

Source playback begins to fade in 3

minutes before the set time and the volume gradually increases to the set volume. Then, at the set time, the

beep sound is activated.

SOURCE

The selected audio source is played at the set time. The volume fades in gradually and increases to the set

volume.

BEEP The beep sound is played at the set time.

Source

Playback

method

Function

iPod Resume

The unit resumes play from the last track you played.

If you’ve created a playlist* with the name “ALARM Yamaha DTA” in advance, the

playlist

stored on the iPod can be played back repeatedly.

When entering the playlist name, use single-byte spaces to separate

words, and enter

single-byte characters, taking care that uppercase/lowercase letters are used correctly.

Audio CD

Selected track The selected track is played repeatedly.

Resume The track you listened to last time is played back.

Data CD/USB device

Folder The selected folder is played repeatedly.

Resume The track you listened to last time is played back.

FM

Preset station The selected preset station is played.

Resume The FM station you listened to last

time is played back.

USEFUL FUNCTIONS

18 En

 Setting the alarm time and alarm type (Option menu)

The alarm will not function when the unit is in power saving (☞ P. 16 ). To use the alarm function, set the Option menu item POWER

SAVING to NORMAL.

Setting the alarm

1 Press OPTION.

The option menu will appear.

2 Press  /  to select “ALARM SET”, and then press ENTER.

The alarm indicator ( ) and numerical value you’re setting will blink.

3 Set the alarm.

Set items 1-5 described below.

Press

 /  to select a numerical value, and press ENTER to confirm it.

4 Complete the settings.

When you set the VOLUME for item 5, the display will indicate

“Completed!” and your settings will be confirmed.

The alarm will be turned on and the alarm indicator ( ) will light.

If you press OPTION or turn off the system while making alarm settings, the settings

will be cancelled.

4

9:12



Completed!

Alarm time

Alarm indicator

3

1

2

Items Setting or range

1

ALARM SELECT

* This can be selected after you’ve used the “DTA

Controller” to set the alarm (☞ P. 20).

If you’re not using the “DTA Controller”, proceed to

2

.

ONE DAY: An alarm that sounds only once at the

specified time.

WEEKLY:

An alarm whose time can be specified for

each day of the week (

settable only using

“DTA Controller”).

If you’ve chosen WEEKLY, this completes the alarm

setting.

2

ALARM TIME

Make settings in the order of hours minutes.

3

ALARM TYPE

Select from SOURCE+BEEP, SOURCE or BEEP. For

details, refer to “3 types of alarms” (P. 17)

.

If you selected BEEP, proceed to item

5.

4

SOURCE

(If you selected

SOURCE+BEEP or

SOURCE as the

alarm type)

iPod: Play back music from your iPod (

refer to

“Various audio sources” (P. 17)

).

The iPod connected via Bluetooth is not

available. Set the iPod in the iPod dock.

CD: Play back music from a CD.

Specify the track number (data CD: folder

number) (RESUME, 1-99).

USB: Play back music from a USB device.

Specify the folder number (RESUME, 1-999).

FM: Play a FM station.

Specify the preset number (RESUME, 1-30).

If the selected source cannot be played back at the time set

for the alarm (e.g., the iPod is not connected), the beep

sound is played back.

If you choose RESUME when specifying the track/folder/

preset number, the last-played track/folder/station will be

played (resume playback)

5

VOLUME

Specifies the volume (5-60) of the alarm.

19 En

USEFUL FUNCTIONS

English

 Switching the alarm on/off

When the set time arrives, the selected alarm sound will play. During playback, the following operations are available.

 To pause the alarm (Snooze)

 To turn the alarm off

Press ALARM to turn the alarm on/off.

When the alarm is on, the alarm indicator ( ) will light,

and the alarm time will be shown.

If you press ALARM ag

ain, the alarm indicator ( )

and the alarm will turn off.

If the Option menu item POWER SAVING is set to ECO,

the alarm will not function (☞ P. 16).

Operations while the alarm sound is playing

Press SNOOZE/SLEEP.

Snooze will stop the alarm and play it again 5 minutes later.

• If SOURCE + BEEP is set as the alarm type, you can press

SNOOZE/SLEEP once to stop the beep sound, and twice to stop

the audio source.

Five minutes after the audio source i

s stopped, it will start fading

in again and the beep sound will resume.

• Buttons on the unit other than the will also function as the

snooze button.

Press ALARM or .

• You can also stop the alarm by holding down SNOOZE/SLEEP.

• If you don’t stop the alarm, it w

ill stop automatically after 60

minutes and the system will turn off.

• The alarm setting will be saved even if the alarm is turned of

f.

If the alarm is turned on

again by pressing ALARM, the alarm

will sound with the previous alarm settings.

Page is loading ...

Yamaha MCR-042 Owner's manual

This manual is also suitable for

Yamaha MCR-042 Owner's manual

in other languages

Related papers

Other documents