Daewoo DTD 5000 User manual

Page is loading ...

29

USER MANUAL

EN

DTD 5000

Getting started

Location

Setting up

Getting to know your phone

Handset and charger

Handset display icons

Base

Menu

Using the phone

Switch the handset power on/o

Make an external call

Preparatory dialling

End a call

Receive a call

Earpiece volume

Secrecy (mute)

Handsfree

Redial

Keypad lock

Switching the torch on/o

Paging

50 Name and number phonebook

Handset menu

Keypad beeps

Handset ringer volume/melody

Handset name

Display language

Auto answer

Keypad lock

Set-up menu

Base ringer volume/melody

PIN code

Dial mode

Recall mode

Restore default settings

Date and time settings

Set the date/time

Calling Features

Caller Display

Call list

View and dial from the Calls list

Copy list number to the phonebook

Delete an entry/all entries

Using additional handsets

Registering a new handset

Registering another type of handset to your

Base

Select a base

De-register a handset

Internal calls

Transferring calls

3-Way Call

Help

General information

Safety information

Cleaning

Environmental

Product disposal instructions

Declaration of conformity

Warranty

30

33

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

30

USER MANUAL

EN

DTD 5000

GETTING STARTED

Location

Your phone comes with a base which you will need to place within 2 metres of a mains power

socket and telephone socket so that the cables will reach.

The charger can then be located wherever you want in your house, provided it is within reach of a

mains power socket.

The handset can be charged using the charger. Make sure the base is at least 1 metre away from

other electrical appliances to avoid interference.

Your phone works by sending radio signals between the handset and base. The strength of the

signal depends on where you site the base. Putting the base unit as high as possible can help

provide the best signal/range.

The phone has a range of up to 1000 metres outdoors when there is a clear line of sight between

the base and the handset. When there is no clear line of sight between the base and the handset

the range could be reduced to 50 metres. Thick stone walls can severely a ect the range.

Signal strength

The icon on your handset indicates when you are in range. When you move out of range of

the base, the out of range tone will sound every minute and the icon will  ash on the handset

display. This is repeated until you move back into range.

Setting up

1. At the handset: Make sure the battery ribbon is laying  at inside the battery compartment and

insert the 2 x AAA NiMH rechargeable batteries supplied observing the polarity markings (+ and

-).

Battery low warning

If the symbol  ashes in the display and you hear a warning beep every minute, you will

need to recharge the handset before you can use it again.

31

USER MANUAL

EN

DTD 5000

Replace the battery cover, then lower and screw the cover into place. Finally, screw the belt clip on.

At the base: Plug the mains power cord into the socket on the underside of the base and plug the

other end into the mains power wall socket. The green Power/In use light comes on and you will hear

a con rmation tone.

Telephone line cord

(DO NOT connect to the wall socket until

the handset is fully charged)

Power adaptor cable

3

50

8

32

USER MANUAL

EN

DTD 5000

At the charger: Plug the charger power cord into the charger and the mains power wall socket.

Place the handset on the base to charge for at least 24 hours. The red Charging light comes on.

While the handset is charging, the symbol scrolls in the display, when the handset is fully

charged the display shows the symbol.

Wall mounting (optional)

If you wish you can wall mount the handset and charger.

1. Drill two holes in the wall for the 2 screws provided using the wall mounting bracket as a

template.

2. Insert the wall plugs provided into the holes and then insert he 2 screws.

3. Thread the power cable from the charger through the hole in the bracket and thread the cable

into the cable groove on the underside. Secure the charger onto the bracket by screwing the 3

screws supplied into the underside of the bracket.

4. Fix the bracket (now with charger attached to it) onto the screws protruding from the wall, by

placing it over the screw heads then pull it down gently and it should drop down and secure into

place.

Your phone is ready for use.

/

33

USER MANUAL

EN

DTD 5000

Earpiece / receiver

Torch On / O (located on back of handset)

Press and hold to switch the torch on, page 39.

Release the button to switch the torch o ,

page 40.

Handset and charger

Display with orange backlight

Backlight comes on when you receive

a call or when any button is pressed.

Secrecy / Clear / Back

In talk mode, press to switch secrecy

(mute) on/o , page 37.

In entry mode, press to delete digits.

In menu mode, press to move back to

the previous screen or press and hold

to exit and return to standby.

When viewing the Calls list/Redial list,

press to delete the displayed entry or

press and hold todelete all entries.

Redial / Scroll Up / Volume +

In standby mode, use to redial any of

the last 10 numbers called, page 38.

In talk mode, press to increase the

handset earpiece volume, page 37.

Use to scroll up through the

phonebook, redial list and Calls list.

Talk

In standby mode, press to make

or receive calls.

In talk mode, press to end a call,

page 36.

Calls / Scroll Down / Volume -

In standby mode, press to open the

Calls list, page 46.

In talk mode, press to decrease the

handset earpiece volume, page 37.

Use to scroll down through the

phonebook, redial list and Calls list.

* / Keypad lock

Switch temporarily from pulse to

tone dialling.

From standby, press and hold to lock

the keypad, pag 39.

Handsfree

In standby mode, use to switch handsfree

on and o , page 38.

Menu / OK

In standby mode, press to access and scroll

through the menu options, page 35.

Press to con rm a displayed option.

Phonebook / Exit

In standby or talk mode, press to open the

Phonebook, page 40.

When viewing the Redial list/Calls list or

when editing, press to exit and return to

standby.

Alphanumeric keypad with orange

backlight

Use to enter digits and characters.

Recall / Power On/O

For use with a switchboard/PBX and

BT Calling Features.

Use to switch the handset power on/o ,

page 36.

Int

In standby or talk mode, use to make

an internal call, page 50.

Microphone

EXT

INT

EXT

INT

EXT

INT

34

USER MANUAL

EN

DTD 5000

Handset

Displayed when the line is in

use.

Ext

Displayed when an external

call is being received or in

progress.

Int

Displayed when an internal call

is being received or in progress.

New Calls (Telephone)*

Flashes to indicate new Calls

list entries.

Person/Handset*

When viewing the Calls list,

indicates a call you answered.

* You must subscribe to your

network provider’s Caller

Display service for this feature

to work.

Person*

When viewing the Calls list,

indicates an unanswered call.

Phonebook

Displayed when the

phonebook is in use.

Menu

Displayed when the menu is

in use.

Battery status

Shows handset battery status.

Scrolls when the handset is

charging in the base.

Range

Displayed in standby mode to

indicate handset is in range

of the base. Flashes if you go

out of range or if a handset is

not registered.

Keypad lock

Displayed when the keypad

is locked.

Left arrow or Right arrow

Indicates that the displayed

number/text message is lon-

ger than the screen (12 digits

or more).

Alarm bell

Displayed when the alarm

is set.

Envelope

Displayed to indicate new text

messages in the Inbox.

Handsfree speaker

Displayed when in

handsfree mode.

Handset display icons – These are the symbols you will see on your handset’s screen

/

35

USER MANUAL

EN

DTD 5000

Power / In use / Calls light / Message Indicator

Illuminates when the power is connected.

Flashes when receiving a call and during a call,

when you have new text messages or Calls list

entries waiting and when the phone is in

registration mode.

Page (Find handset)

Press to page/locate a missing handset,

page 40.

Base

Navigating the menus

Your phone has an easy to use menu system. Each menu has a list of options, which you can see

on the menu map on the following page.

When the handset is switched on and in standby:

1. Press to open the main menu, then press or repeatedly to scroll to the menu option

you want.

2. Press to select a displayed menu option or press to go back to the previous screen.

Press repeatedly to exit and return to standby.

EXT

INT

/

36

USER MANUAL

EN

DTD 5000

Menu map

Switch the handset power on/o

When you make a call, the backlight on the handset display comes on and the In Use light on the

base  ashes.

To switch o : Press and hold until the display goes o .

To switch on: Press and hold for 3 seconds and the display will come back on.

Make an external call

1. Lift the handset and press .. The and symbols are displayed.

2. When you hear the dialling tone, dial the number you want.

Preparatory dialling

1. Enter the number  rst. If you make a mistake, press to delete the last digit.

2. Press to dial.

Phonebook

Add Entry

Modify Entry

Delete Entry

SMS

Inbox

Personal SMS

Write

Delete All

SMS Settings

Msg Alert

Send Service

Rcv Center

Send Center

Terminal No

Setup

Base Volume

Base Melody

Del Handset

Pin Code

Dial Mode

Recall Mode

Default

Handset

Beep

Keytone

Low Battery

Out Of Range

Int Ring Vol

Ext Ring Vol

Int Melody

Ext Melody

Auto Answer

Handset Name

Language

Key Lock ?

Date & Time

Set Date

Set Time

Set Alarm

Register

Select Base

Reg Base

EXT

INT

EXT

INT

EXT

INT

/

37

USER MANUAL

EN

DTD 5000

End a call

1. Press or place the handset back on the charger.

Receive a call

When you receive a call, the phone rings, the symbol  ashes, the keypad backlight comes

on and the Calls light on the base  ashes. Call is displayed and the or symbol  ashes

to let you know if it is an external or internal call.

If your handset is on the charger and auto-answer is on: pick up the handset to answer the call or

If your handset is on the charger and auto-answer is o : pick up the handset and press to

answer the call.

If your handset is o the charger, press .

Ringer volume

While the phone is ringing, you can use or to adjust the ringer volume.

Caller Display

If you have subscribed to your network’s Caller Display service, the caller’s number (or name if

stored in the phonebook) is displayed. See page 46 for more information.

Earpiece volume

During a call you can adjust the volume of the earpiece/handset receiver. There are 5 volume

levels to choose from.

1. Press to increase or to decrease the volume.

Secrecy (mute)

During a call, you can mute the microphone and talk to someone nearby without your caller

hearing.

1. Press . Mute is displayed while the microphone is muted and your caller cannot hear you.

2. Press again to resume your conversation with your caller.

//

/

38

USER MANUAL

EN

DTD 5000

Handsfree

Handsfree lets you talk to your caller without holding the handset. It also enables other people in the

room to listen to your conversation over the loudspeaker.

Make a handsfree call

1. Press then dial the number. The icon is displayed and you hear your call over the loudspeaker.

2. Press to end the call.

Switch to handsfree during a call

During a call:

1. Press . The call is transferred to the loudspeaker.

2. Press to end the call.

During a handsfree call, press or to change the volume.

Redial

The last 10 telephone numbers called are saved to a redial list. You can then select any of the numbers to

redial, delete or copy them to the directory.

Dial a number from the redial list

1. Press . The last number called is displayed.

2. Use or to scroll through the redial list to the number you want and press to redial.

If the number is stored in the phonebook and a name/number match is found, the name will be

displayed instead. To toggle between the name and number, press OK.

Delete a number from the redial list

1. Press . The last number called is displayed.

2. Use or to scroll through the redial list to the number you want.

3. Press , Delete? is displayed, press to con rm or press to cancel.

4. Press to return to standby.

To rch

/

39

USER MANUAL

EN

DTD 5000

Delete the entire redial list

1. Press . The last number called is displayed.

2. Press and hold , Delete All? is displayed, press to con rm. Or press to cancel.

3. Press to exit and return to standby.

Copy a redial list number to the phonebook

1. Press . The last number called is displayed.

2. Use or to scroll and display the number you want, then press .

3. Add? is displayed, press .

4. Name? is displayed. Enter a name using the keypad and press .

5. The redial number is displayed. If you wish you can edit the number. When the number is

correct, press .

6. Press or to select a melody and press to save the entry.

7. Press to exit and return to standby.

Keypad lock

You can lock the keypad so that it cannot be used accidentally while carrying it around.

To lock the keypad:

1. Press and hold for 3 seconds. The display shows the symbol.

To unlock the keypad:

1. Press any key. The display shows Press *.

2. Press within 3 seconds to unlock the keypad.

Switch the torch on/o

To help you see in dark or poorly lit environments, you may  nd the torch a handy feature.

To switch on:

1. Press and hold to switch the torch light on. The button can be found on

the back of the handset.

EXT

INT

/ /

/

40

USER MANUAL

EN

DTD 5000

To switch o :

1. Release to switch the torch light o .

Paging

You can alert a handset user that they are wanted or locate a missing handset.

1. Press on the base. All handsets registered to your phone base will beep and display the

symbol and ring.

2. Press again to stop the paging ring. Or press any button on the handset.

50 Name and number phonebook

You can store up to 50 names and numbers in the phonebook. Names can be up to 12 characters

long and numbers up to 24 digits. You can also select from 10 di erent ringtones for phonebook

entries.

Store a phonebook name and number

1. Press to open the main menu. Phonebook is displayed, press .

2. Add Entry is displayed, press .

3. Enter a name using the keypad and press .

4. Enter a telephone number using the keypad and press .

5. Use or to select a melody, press to con rm.

6. Press repeatedly to exit and return to standby.

Dial an entry

1. Press to open the phonebook list.

2. Use or to scroll and  nd the entry you want and press to dial the displayed number.

Edit a phonebook name or number

1. Press to open the main menu, Phonebook is displayed, press .

2. Press or to select Modify Entry and press .

3. Use or to scroll and  nd the entry you want to edit and press to select.

/

41

USER MANUAL

EN

DTD 5000

4. The name is displayed. Use to delete any incorrect characters and enter new ones using

the keypad and press to con rm.

5. The number and melody will be displayed. You can change them by following instructions on

point 5.

6. Press repeatedly to exit and return to standby.

To see the number before dialling, with the entry name displayed, press . If the number has

more than 12 digits, press to view the remaining digits.

If you access the phonebook by pressing rather than via the menu and you edit a name /

number, the modi cation will only be taken into account for the current call and will not be sto-

red to the phonebook permanently.

Delete a phonebook entry

1. Press to open the main menu, Phonebook is displayed, press .

3. Press or to select Delete Entry and press .

4. Use or to scroll and  nd the entry you want to delete (or search alphabetically) and press

to select.

5. Con rm? is displayed. Press to con rm.

6. Press repeatedly to exit and return to standby.

Keypad beeps

Your phone has a selection of beeps / warning tones which can be set to on, to alert you to

certain situations:

- Key tones – where a beeps sounds every time a keypad button is pressed (to con rm the button

press).

- Low battery warning tone – a beep alerts you when the batteries are low and need recharging.

- Out of range tone – when the handset moves too far from the base and goes out of

communication range a warning tone will sound.

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

3. Beep is displayed, press .

4. Use or to display either Keytone, Low Battery or Out Of Range and press .

5. Use or to select On to activate the beeps, or O to deactivate the beeps and press .

6. Press repeatedly to exit and return to standby.

/

42

USER MANUAL

EN

DTD 5000

Handset ringer volume

The handset has 6 ringer volume settings: O and 1–5.

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

3. Press or to select either Int Ring Vol or Ext Ring Vol and press .

4. Press or to highlight the volume you require and press to con rm.

5. Press repeatedly to exit and return to standby.

Handset ringer melody

You can choose from 10 polyphonic ringer melodies for both external and internal calls.

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

3. Press or to select either Ext Melody or Int Melody and press .

4. Use or to hear and select a melody. Press to con rm your selection.

5. Press repeatedly to exit and return to standby.

Handset name

You can give your handset a name to personalise it.

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

3. Press or to display Handset Name and press .

4. The existing handset name is displayed, followed by a  ashing cursor. Use to delete the current

name and enter a name using the keypad, then press to con rm.

5. Press repeatedly to exit and return to standby.

Display language

You can change the language that is shown on your handset display. There are 17 languages to

choose from.

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

/

43

USER MANUAL

EN

DTD 5000

3. Press or to display Language and press .

4. Press or to highlight the language you want and press to con rm.

5. Press repeatedly to exit and return to standby.

Auto answer

If you set auto answer to On, when you receive an incoming call and the handset is in the charger,

you can pick it up to answer the call. You do not need to press .

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

3. Press or to display Auto Answer and press .

4. Press or to select either On or O and press to con rm.

5. Press repeatedly to exit and return to standby.

Keypad lock

You can lock the keypad so that it cannot be used accidentally while carrying it around.

To lock the keypad.

1. Press to open the main menu.

2. Press or until Handset is displayed, then press .

3. Press or to display Keylock? and press to con rm.

While the keypad is locked, the icon will be displayed.

Press within 3 seconds to unlock the keypad.

Base ringer volume

The base has 6 ringer volume settings: O and 1–5.

1. Press to open the main menu.

2. Press or until Setup is displayed, then press .

3. Base Volume is displayed, press .

4. Press or to highlight the volume you require and press to con rm.

5. Press repeatedly to exit and return to standby.

/

44

USER MANUAL

EN

DTD 5000

Base ringer melody

The base has 5 ringer melodies to choose from.

1. Press to open the main menu.

2. Press or until Setup is displayed, then press .

3. Press or to select Base Melody and press .

4. Use or to hear and select a melody. Press to con rm your selection.

5. Press repeatedly to exit and return to standby.

PIN code

Your phone has a security PIN code which you will need to change some of the settings on your

phone. The default PIN code is 0000. To change it:

1. Press to open the main menu.

2. Press or until Setup is displayed, then press .

3. Press or to select Pin Code and press .

4. Enter the current 4 digit PIN code and press .

5. Enter a new 4 digit PIN code and press , re-enter the new PIN code and press .

7. Press repeatedly to exit and return to standby.

Dial mode

The dialling mode is pre-set to Tone. If you are using your phone with an older type of switchboard/

PBX you may required to change this setting to Pulse dialling.

1. Press to open the main menu.

2. Press or until Setup is displayed, then press .

3. Press or to select Dial Mode and press .

4. Use or to highlight the dial mode you want and press to con rm your selection.

5. Press repeatedly to exit and return to standby.

Recall mode

If your switchboard does not operate with the present recall setting you can change it to earth loop

recall by selecting Earth.

/

45

USER MANUAL

EN

DTD 5000

There are 2 recall mode settings:

Recall – for time break recall. This is the default setting.

Earth – for earth loop recall.

1. Press to open the main menu.

2. Press or until Setup is displayed, then press .

3. Press or to select Recall Mode and press .

4. Use or to highlight the recall setting you want and press to con rm your selection.

5. Press repeatedly to exit and return to standby.

Restore default settings

You can restore your phone to its default (original) settings.

1. Press to open the main menu.

2. Press or until Setup is displayed, then press .

3. Press or to select Default and press .

4. Enter the 4 digit PIN code and press .

5. Con rm? is displayed, press to con rm the reset. The handset will switch o , then switch back

on again with the default settings restored.

Please note, restoring the default settings will delete your phonebook, redial and calls list.

Restore default settings without a PIN

If you have forgotten your PIN code, you can restore your phone to the default settings following the

procedure shown below.

1. Unscrew and remove the belt clip and battery compartment cover.

2. Remove the batteries for a few minutes. Press and hold , while still pressing the button,

insert the batteries again observing the polarity markings (+ and -).

3. Default is displayed, press .

When the phone powers up, the default settings will be restored.

Set the date and time

1. Press to open the main menu.

2. Press or until Date & Time is displayed, then press .

/

46

USER MANUAL

EN

DTD 5000

3. Set Date is displayed, press .

4. Enter the date (dd/mm) e.g. for 15th February, press 1, 5, 0, 2, then press .

5. Press or to select Set Time and press .

6. Enter the time in 24-hour format, e.g. for 9:24pm press 2, 1, 2, 4, then press .

7. Press repeatedly to exit and return to standby.

Set the alarm

1. Press to open the main menu.

2. Press or until Date & Time is displayed, then press .

3. Press or to select Set Alarm and press .

4. Press or to select either:

On to switch the alarm on and press . The previous alarm time setting is displayed. Enter the

time you want the alarm to sound in 24 hour format.

Or

O to switch the alarm o and press .

5. Press repeatedly to exit and return to standby.

When the alarm is set the symbol will be displayed when in standbymode.

Silence the alarm

When the alarm time is reached, the alarm will sound and Alarm On will  ash in the display.

1. Press any button on the handset to silence the alarm.

Caller Display

If you have subscribed to a Caller Display Service, you will be able to see your caller’s number on your

handset display (provided it is not withheld) prior to answering the call.

If your caller’s name and number are stored in the phonebook and a name/number match is found,

you will see the caller’s name alternating with their telephone number on the display.

/

47

USER MANUAL

EN

DTD 5000

Calls list

The Calls list holds up to 40 telephone numbers and they are stored in the order they were recei-

ved. If a call is received when the list is full, the oldest entry will be deleted automatically.

When a new call is received in the Calls list the icon will  ash in the display when in standby

mode to alert you.

View and dial from the Calls list

1. Press . The most recently received number or name is displayed. If there are no entries, Empty

will be displayed.

If you answered the call, you will see the symbol. If the call was not answered, you will see the

symbol.

2. Use or to scroll through the list. With a name displayed, press OK repeatedly to view the

caller’s number and the date and time the call was received.

3. To dial a displayed number, press . The number will be dialled automatically.

Or

To exit and return to standby, press . When all new calls have been viewed the symbol

will disappear from the display.

Copy a Calls list number to the phonebook

1. Press . The most recently received number or name is displayed.

2. Use or to scroll through the list to the number you want to store.

3. Press repeatedly until Add? is displayed, then press .

4. Enter a name using the keypad, then select the option.

5. The number is displayed, (if necessary, edit the number), then press .

6. The ringer melody options are displayed, use or to select the one you want press. The

entry is stored to the phonebook.

7. Press to return to standby.

Delete an entry/all entries in the Calls list

1. Select the option. The most recently received number or name will be shown.

2. Use or to scroll through the list.

3. Press and release to delete the currently displayed entry only. Delete? is displayed.

/

48

USER MANUAL

EN

DTD 5000

Or

Press and hold to delete all entries. Delete All? is displayed.

4. Press to con rm you want to delete. or Press if you decide not to delete.

5. Press to return to standby.

Using additional handsets

You can use up to  ve GAP compatible handsets with your base to extend your phone system

without needing to install extension sockets for each new phone.

Your phone handset can be registered to up to 4 bases.

You need to register any additional handsets you purchase to your Daewoo base.

Registering a new handset

At the base:

1. Press and hold until you hear a beep, then release it.

The base will now remain in registration mode for 90 seconds.

At the new handset:

2. Press to open the main menu.

3. Press or until Register is displayed, then press .

4. Press or to highlight Reg Base and press .

5. Enter a base number (from 1 to 4) and press .

6. Enter the 4 digit PIN code and press .

When the base is located, your handset will display the base ID number, press to con rm

registration to this base or cancel by pressing .

The handset is automatically allocated the next available handset number which is displayed when in

standby mode.

Page is loading ...

Daewoo DTD 5000 User manual

This manual is also suitable for

Daewoo DTD 5000 User manual

in other languages

Related papers

Other documents