2. Extron
  3. SMK C TB Series

Extron SMK C TB Series User manual

  • Hello! I am an AI chatbot trained to assist you with the Extron SMK C TB Series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
SMK C TB Series Setup Guide
The Extron SMK C TB Series of tile-bridge ceiling mount kits utilize folding C-rings and
modular V-rails.
1. Cut a hole in the ceiling using the cutout template provided with the speaker.
2. Assemble the two V-rail to the extension bar by tting the tab on one end into the
slot of the other end. Open the V-rail until it locks together, as shown below. Repeat this
procedure for the other V-rail.
3. Remove the ceiling tile adjacent to the tile with the hole for the speaker.
SMK C TB Series Setup Guide
The Extron SMK C TB Series of tile-bridge ceiling mount kits utilize folding C-rings and
modular V-rails.
1. Cut a hole in the ceiling using the cutout template provided with the speaker.
2. Assemble the two V-rail to the extension bar by tting the tab on one end into the
slot of the other end. Open the V-rail until it locks together, as shown below. Repeat this
procedure for the other V-rail.
3. Remove the ceiling tile adjacent to the tile with the hole for the speaker.
SMK C TB Series Setup Guide
The Extron SMK C TB Series of tile-bridge ceiling mount kits utilize folding C-rings and
modular V-rails.
1. Cut a hole in the ceiling using the cutout template provided with the speaker.
2. Assemble the two V-rail to the extension bar by tting the tab on one end into the
slot of the other end. Open the V-rail until it locks together, as shown below. Repeat this
procedure for the other V-rail.
3. Remove the ceiling tile adjacent to the tile with the hole for the speaker.
SMK C TB Series Setup Guide
The Extron SMK C TB Series of tile-bridge ceiling mount kits utilize folding C-rings and
modular V-rails.
1. Cut a hole in the ceiling using the cutout template provided with the speaker.
2. Assemble the two V-rail to the extension bar by tting the tab on one end into the
slot of the other end. Open the V-rail until it locks together, as shown below. Repeat this
procedure for the other V-rail.
3. Remove the ceiling tile adjacent to the tile with the hole for the speaker.
68-3397-50 Rev. A
03 19
© 2019 Extron Electronics. All rights reserved. www.extron.com
See the Extron Safety and Regulatory Compliance Guide on the Extron website.
68-3397-50 Rev. A
03 19
© 2019 Extron Electronics. All rights reserved. www.extron.com
See the Extron Safety and Regulatory Compliance Guide on the Extron website.
68-3397-50 Rev. A
03 19
© 2019 Extron Electronics. All rights reserved. www.extron.com
See the Extron Safety and Regulatory Compliance Guide on the Extron website.
68-3397-50 Rev. A
03 19
© 2019 Extron Electronics. All rights reserved. www.extron.com
See the Extron Safety and Regulatory Compliance Guide on the Extron website.
4. Place both assembled V-rails on the cut ceiling tile and position them equally on either side
of the hole. The ends of the V-rails go over the ceiling grid.
5. Position the C-ring assembly on the two V-rails so that the C-ring is centered over the hole.
V-rail
C-ring
Screws
6. Secure the C-ring to the V-rails using two screws, as shown above.
7. Refer to the speaker’s setup and user guides for further instructions.
4. Place both assembled V-rails on the cut ceiling tile and position them equally on either side
of the hole. The ends of the V-rails go over the ceiling grid.
5. Position the C-ring assembly on the two V-rails so that the C-ring is centered over the hole.
V-rail
C-ring
Screws
6. Secure the C-ring to the V-rails using two screws, as shown above.
7. Refer to the speaker’s setup and user guides for further instructions.
4. Place both assembled V-rails on the cut ceiling tile and position them equally on either side
of the hole. The ends of the V-rails go over the ceiling grid.
5. Position the C-ring assembly on the two V-rails so that the C-ring is centered over the hole.
V-rail
C-ring
Screws
6. Secure the C-ring to the V-rails using two screws, as shown above.
7. Refer to the speaker’s setup and user guides for further instructions.
4. Place both assembled V-rails on the cut ceiling tile and position them equally on either side
of the hole. The ends of the V-rails go over the ceiling grid.
5. Position the C-ring assembly on the two V-rails so that the C-ring is centered over the hole.
V-rail
C-ring
Screws
6. Secure the C-ring to the V-rails using two screws, as shown above.
7. Refer to the speaker’s setup and user guides for further instructions.
/