2. RTS
  3. Oki - kp 12 cld

RTS Oki - kp 12 cld, Oki - kp 32 cld User manual

  • Hello! I am an AI chatbot trained to assist you with the RTS Oki - kp 12 cld User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Quick Start Guide
OKI - OMNEO Keypanel Interface KP 12 CLD
Included:
• OMNEOKeypanelModule
• RearPanel,KP12CLD,Expansion
• 2-Screw,4-40x.25LG.
• 3-Screw,PH,4-40x3/16LG.
• SafetyInstructionsST-CO
• OKIQuickStartGuide
• OKIDocumentationResourceDisk
Requirements:
Youmusthavethefollowing:
• PhillipsScrewdriver
• HexNutDriver
Firmware Requirements
• KP12CLDversion1.30
IMPORTANT Thekeypanelrmwaremustbeupdatedbefore
youinstalltheOKImoduleintothekeypanel.
Reference View - OKI KP 12 CLD
Description
1.J1&J2 RJ-45Connectors(2)
2.J3 LCFiberConnector(Optional)
OKI Installation – KP 12 CLD
Toinstall the OKI board set for the KP 12 CLD,dothe
following:
NOTE:Becauseallthechangesaremadetothe
expansionbox,removetheexpansionboxfrom
theKP12CLDunit.
1. PowerofftheKP12CLDunit.
2. Removetheexpansion boxfromtheKP12CLD
unit.
NOTE:Steps3and4areonlynecessaryifanRCoption
isinstalled.
3. Usingahexnutdriver,removethe12 hex screws
fromtheKP12CLDexpansionbox.
4. Usingthesamescrewdriver,removetheeight (8)
pan head screwsfromtheKP12CLDexpansion
box.
5. UsingaPhillipsscrewdriver,removethesix (6) at
head screwsfrom KP12CLDexpansionbox.
F01U280811Rev01 01/2013
Quick Start Guide
OKI - OMNEO Keypanel Interface KP 12 CLD
6. RemovetheKP 12 CLD expansion box cover.
7. Ifinstalled,removetheRVON standoffs.
8. Replacethestandoffswiththeprovidedpan head
screws (3).
Caution: EnsurethatallRJ-45connectorsonthe
boardareushwiththechassisopenings.
9. Usingtheprovidedpanheadscrews(2),secure
theOKI board set to the OKI KP 12 CLD
expansion box replacement cover.
NOTE:ItiseasiertoinstalltheOKIboardsettothe
OKIKP12CLDexpansionboxbackpanel
whiletheboardsetandthechassisarelaying
upsidedown,seepicturebelow.
NOTE: AligntheredstripeonthecablewithPin1.
10. Attachone end of the provided ribbon cable to
J2ontheOKIboardset.
11. Attachtheother end of the ribbon cable to J5
ontheKP12CLDexpansionboxmainboard.
12. Replacetheexisting cover with the OKI KP 12
CLD expansion box cover.
Caution: EnsurethatallRJ-45connectorsonthe
boardareushwiththechassisopenings.
13. Replacetheeight (8) pan head screws.
14. Replacethesix (6) at head screws.
15. Replacethe12 hex screws.
16. Usingtheexistingscrews,securetheOKI KP 12
CLD expansion box covertothechassis.
17. RemounttheKP 12 CLD expansion boxtothe
KP12CLDunit.
/