Honeywell Safes & Door Locks 8712009 Installation guide

Brand
Honeywell Safes & Door Locks
Model
8712009
Type
Installation guide
Page 1
Model DDBKP
Read this manual carefully before installing and operating!
ENGLISH
Installation & Operation Guide
Digital Deadbolt
Page 2
Index
INSTALLATION INSTRUCTIONS
Package Contents / Tools Required..........................................................
Prepare Door and Jamb.............................................................................
Adjusting Deadbolt Latch Set..................................................................
Installing Deadbolt Latch Set.....................................................................
Installing Exterior Assembly........................................................................
Installing Interior Assembly........................................................................
OPERATION INSTRUCTIONS
Digital Keypad Overview.............................................................................
Locking and Unlocking / Changing Programming Code /
Adding User Codes......................................................................................
Deleting User Codes / Automatic Lock Function /
Sound On and Off........................................................................................
Secure Lock-out Period / Restore Factory Settings /
Low Battery Warning / Consumer Friendly Message Guide....................
Installation Trouble Shooting...............................................................
Customer Service........................................................................................
Template.......................................................................................................
Programming Record..................................................................................
Limited Warranty.................................................................................
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6-8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15-16
Page 17
Back
Cover
Page 1
INSTALLATION INSTRUCTIONS
Package Contents
Tools Required
Tools Required for Installation
on Pre-drilled Doors:
•PhillipsScrewdriver
Tools Required for Installation
on Doors That Require Drilling:
•Drill
•TapeMeasure
•Pencil
•2-1/8”(54mm)DrillHoleSaw
•1”(25mm)Drill
•1/16”(2mm)Drill
•Chisel
•Hammer
•PhillipsScrewdriver
DO NOT RETURN TO STORE! If any parts are missing or damaged,
pleasecallCustomerServicetollfreeat1-877-354-5457(M-F7am–5pmPST)
Deadbolt Strike Plate
DeadboltLatchSet(Adjustable)
2-3/8”(60mm)to2-3/4”(70mm)
5/16”(8mm)Screws-2ea. 1”(25mm)Screws-2ea.
3/4”(19mm)Screws-5ea. 1-3/8”(35mm)Screws-1ea.
InteriorAssembly
Mounting Plate
ExteriorAssembly
Entrykeys(2ea.)
Page 2
ADJUSTABLEDEADBOLTLATCHSET
NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm)
Measurethebackset(backsetisdistancebetweenedgeofthedoorandthe
centerofLock).
1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET
a.Holdlatchwithnumbersfacingforwardandthumbpressingonthebolt(Figure1a).
b.Rotatethecylindercoverclockwise(Figure1b).
c.Pullandtwisttheextensionplateallthewayout(Figure1c).
d.Rotatethecylindercovercounterclockwisesothatthemarkingalignswith
the2-3/4”(70mm)positionindicator(Figure1d).
2. TO CONVERT FROM 2-3/4” (70mm) BACKSET TO 2-3/8” (60mm) BACKSET
a.Holdlatchwithnumbersfacingforwardandthumbpressingonthebolt(Figure2a).
b.Rotatethecylindercoverclockwise(Figure2b).
c.Pushandtwisttheextensionplateallthewayin(Figure2c).
d.Rotatethecylindercovercounterclockwisesothatthemarkingalignswith
the2-3/8”(60mm)positionindicator(Figure2d).
Figure1a
Figure2a
Figure1b
Figure2b
Figure1c
Figure2c
Figure1d
Figure2d
Extension plate
Extension plate
Cylindricalcover
Cylindricalcover
Yourlatchisnowset
2-3/8”(60mm)backset
Yourlatchisnowset
2-3/4”(70mm)backset
2-3/8”
(60mm)
2-3/8”
(60mm)
2-3/4”
(70mm)
2-3/4”
(70mm)
2-3/8”
(60mm)
NOTE: Do not extend Cylindrical Cover past 2-3/4” (70mm)
Page3
NOTE: For installation on doors with pre-drilled holes skip to page 4.
1. TEMPLATE
a.Cutouttemplateprintedonpage15ofthisManual
(Figure1a).
b. Foldtemplateandplaceondoor36”(925mm)from
thegroundasmarked(Figure1b).
2. MARK THE DOOR FOR DRILLING
b. Mark center hole on door edge through guide on
templatefor1”(25mm)latchbolt(Figure2a).
a. Mark center hole on door face through guide on
templatefor2-3/8”(60mm)or2-3/4”(70mm)
backset(Figure2b).
3. DRILL AND CHISEL DOOR
a.Drill2-1/8”(54mm)holethroughdoorfaceasmarked
forlockset(Figure3a).
b.Drill1”(25mm)holeincenterofdooredgefor
DeadboltLatchAssembly(Figure3b).
c.InsertDeadboltLatchAssemblyinholekeepingit
paralleltofaceofdoor.Markoutlineandremovelatch
(Figure3c).
d.Chisel1/8”(3mm)deeporuntillatchfaceisush
withdooredge(Figure3d).
4. MARK AND DRILL DOOR JAMB
a. MarkcenterholeonedgeofjambevenwiththecenteroftheLatchBoltondoor
edge.(Figure4a).
b.Drill1”(25mm)hole1-3/16”(30mm)deepindoorjamboncentermark
(Figure4b).
c.OutlineoutsideedgesofStrikePlate(Figure4c).
d.Chisel1/8”(3mm)deepforStrikePlateoruntilush(Figure4d).
e.InstallStrikePlateusingtwo3/4”(19mm).screwsprovided(Figure4e).
PREPAREDOORANDJAMB
Figure4a Figure4b
Figure4c Figure4e
Figure4d
NOTE: For Drive in Latch, drill hole size indicated on template and press
until it is flush with door edge.
U
P
Figure1a
Figure2a Figure2b
Figure3a
Figure3c
Figure1b
Figure3b
Figure3d
Page4
1. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver)
a.InsertDeadboltLatchSetintodooredgeholewiththeword
“UP”andthearrowontheextensionplatefacingUP.Cross
shapedspindleconnectorwillbeatthebottomoftheDeadbolt
LatchSet(Figure1a).
b.Makesurethefaceplatesitsushwiththedoor.Donotforce
thelatchintothemortiseush.Chiseloutexcessmaterialif
necessaryforausht.
c.Usingtwo3/4”(19mm).screwsprovided,screwthelatchintothe
doorwithahandheldscrewdriver.DONOTOVERTIGHTEN.
2. IDENTIFYING YOUR DOOR HANDING
Stand outside the door
a.IfthehingesareontheleftyourdoorisLeftHanded(Figure2a).
b.IfthehingesareontherightyourdoorisRightHanded(Figure2b).
NOTE: Deadbolt Latch must be retracted when installing
NOTE: You are standing outside the door
INSTALLINGDEADBOLTLATCHSET
OUT SWING DOOR IN SWING DOOR
Figure2a
Left Handed Door
Hinges are on the left side
Left Handed Door
Hinges are on the left side
Right Handed Door
Hinges are on the right side
Right Handed Door
Hinges are on the right side
Figure2b
Figure1a
Deadbolt Latch Extended
Deadbolt Latch Retracted
Page5
2. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR
a.Fromthesidemarked“Thissideagainst
door”,routetheControlWirethroughthe
rectangular slot in the Mounting Plate
(Figure2a).
b.PlaceMountingPlateagainstdoorwithtailpiecepassing
throughthecenterholeinthethreeholeset(Figure2b).
c.SecuretheMountingPlatetotheExteriorAssemblyusing
two1”(25mm)Screws(Figure2c).
d.HandtightenwithaPhillipsScrewdriverleavinglooselyconnected(Figure2d).
e. Check that the Rubber Gasket is properly aligned and correct as necessary
(Figure2e).
f.Checkverticalalignmentofthelock(Figure2f).
g.TightensecurelywithahandheldPhillipsScrewdriver.DO NOT OVER TIGHTEN
3. OPTIONAL INSTALLATION
a.Usinga1/16”(2mm)drillbit,drillapilotholeinyourdoorusingthe
MountingPlateupperholeasaguide(Figure3a).
b. Insert one 3/4”(19mm)screwandtighten.
1. INSTALLING THE EXTERIOR ASSEMBLY
WorkwiththeDoorOpenforeasyaccess.
a.UnpacktheExteriorAssembly.Usecaretonotscratchthegreencircuitboard
during handling and installation.
b.CheckthattheRubberGasketisproperlyseatedontheExteriorAssembly 
(Figure1a).
c.InserttheExteriorAssemblyontothedoorwiththetailpiecegoingthroughthe
Deadbolt Latch Set cross shaped spindle connector in the VERTICAL POSITION.
RoutetheControlWirethroughthedoorovertheDeadboltLatchSet(Figure1b).
NOTE: Deadbolt Latch must be retracted when installing
NOTE: Tailpiece must be
positioned vertically
NOTE: You are standing outside the door
INSTALLINGEXTERIORASSEMBLY
Right handed door view
Rubber
Gasket
Control
Wire
Tailpiece
(Vertical)
Latch
Hole
Mounting Plate
3/4”(19mm)screw
(OptionalInstallation)
1”(25mm)screws
Control Wire
Figure1a Figure1b
Figure3a
Figure2a-2f
NOTE: Lock and unlock using the key to see if
the Deadbolt Latch is opening and closing easily.
Page6
INSTALLINGINTERIORASSEMBLY
1. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR
a.Gentlymovetheswitchto“L”forLeftHandedDoor(Figure1a).
b.GentlymovetheSwitchto“R”forRightHandedDoor(Figure1b).
2. SET THE INTERIOR KNOB POSITION FOR LEFT OR RIGHT HAND HINGED DOORS
a.TheInteriorKnobgoesintheVerticalpositionforRightHandedDoors(Figure2a).
b.TheInteriorKnobgoesintheHorizontalpositionforLeftHandedDoors(Figure2b).
3. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY
a.UsecaretoattachtheControlWiremaleplugtotheInteriorAssemblyfemale
socket connector.
b.DonotforcetheControlWiremaleplugintotheInteriorAssemblyfemale
socket connector.
c.TheControlWiremaleplughastwoalignmenttabsonthesmoothsideofthe
plugwhichisthetopoftheplug.
d.TheControlWiremaleplugisinsertedwiththesmoothsideupintotheInterior
Assemblyfemalesocketconnector.
NOTE: Make sure
deadbolt Latch
is retracted
Left Handed Door
(Horizontal)
Entry Switch
(Left or Right)
Right Handed Door
(Vertical)
UnpacktheInteriorAssembly.Removethebatterycoverbyslidingthecoverupward.Locatethe
screwsholdingtheMountingPlatetotheInteriorAssembly.Removethescrewstoreleasethe
MountingPlatefromtheInteriorAssembly.
Figure1a-1b
Figure2a-2b
Page7
INSTALLINGINTERIORASSEMBLY(CONT.)
4. ATTACH THE INTERIOR ASSEMBLY TO DOOR
a.PositiontheInteriorAssemblyoverthetailpieceandpushtheInteriorAssembly
againstthedoor(Figure4a).
b.Usingtwo5/16”(8mm)screws and one 1-3/8”(35mm)screw, attach
theInteriorAssemblytotheMountingPlate.DO NOT OVER TIGHTEN SCREWS
(Figure4b).
5/16”(8mm)screws
1-3/8”(35mm)screw
NOTE: Lock and unlock using Interior Knob to see if the
latch is opening and closing easily.
INSTALLATION OVERVIEW
Strike Plate
BatteryCover
InteriorAssembly
Key
ExteriorAssembly
Rubber Gasket
Mounting Plate
Latch
5/16”(8mm)
screws
Optional
3/4”(19mm)
screw
3/4”(19mm)
screws
1-3/8”(35mm)
screws
1”(25mm)
Screw
Figure4a-4b
Page8
INSTALLINGINTERIORASSEMBLY(CONT.)
5. Installing Batteries
a.Insert4AAhighqualityAlkalinebatteriesintotheBatteryCompartmentinthe
directionnoted+/-ontheCompartment.TheLockwillbeep2times,thekeypad
willilluminateblue,andtheHoneywellbuttonwillashgreentwicetosignifythat
ithasreceivedpower(Figure5a).
b.SlidetheBatteryCoverdownintothetrackontheInteriorAssemblytocover
thebatteries(Figure5b).
6. Testing Lock
With the Door Open
a.TesttheLockusingtheinteriorKnob.Theboltshouldmovesmoothly.
b.TestthelockusingtheKeypad.Tolockpressandthenpress“1234”
to unlock.
Override
AccessKey
ExteriorAssembly
InteriorAssembly
Interior
Knob
Battery
Cover
Light Indicator
Keypad
NOTE: Do not touch the keypad until the blue light turns off.
Do not use rechargeable batteries or non-alkaline batteries.
Figure5a-5b
Page9
OPERATION INSTRUCTIONS
ExteriorAssemblyOverview
Indicator light
Green
•IndicatesSuccessfulProgrammingStep
•IndicatesUnlockingisSuccessful
Red
•IndicatesFailedProgrammingStep
•IndicatesLockingisSuccessful
Electronic lock requires (4) High Quality
AA Alkaline batteries. When all 4 batteries
are installed in the correct position, hear 2
beeps and the keypad will illuminate blue.
DO NOT TOUCH the keypad until the keypad
stops illuminating.
Lock-Usedtolockdoor
Clear -Usedtoclearwrongkeypadentries
Unlock-Usedtounlockdoor
Programming -Usedinprogrammingsteps
5 Seconds -Completealltheprogrammingstepsintheprogrammingmodewithin5seconds.
Clear -Usethekeytoclearentriesincaseawrongbuttonispushed.
Lock button
Unlock button
FactorySettings
The lock comes factory preset with a:
Please change the Programming
Code and the User Code
as soon as possible after installation
to insure security.
Programming code - 123456
User code - 1234
User ID - 01
ID
PC
PC
UC
UC
Batteries(notincluded)
Programming Symbols
Lock/Clear
Unlock/Programming
Programming Code
User Code (4-8 digits)
User ID (01-50, 2 digits)
ID
PC
UC
Programming Tips
Page10
TO UNLOCK THE LOCK
UsingKeypad:EnteravalidUserCode(defaultcodeis1234)andpressandhear
1 beep and lights green.
TO LOCK THE LOCK
Using Keypad: Press and then hear 2 beeps and lights red.
CHANGECURRENTORPRESETPROGRAMINGCODE
FactorydefaultProgrammingCode=123456,thisisthemasterpasswordfor
yourlock.Allprogrammingfunctionsrequirethiscode.Followthebelowsequenceto
changetheProgrammingCodetoyourcustom6digitcombination.
TOADDANEWUSERCODE(youcanaddupto50newusercodes)
TheUserCodemustbea4-8digitcombination.EachUserCodeisthenlinked
toaUserID(whichisanynumberbetween01-50)toidentifyanindividualUser
Code.(UserID1-9shouldbeenteredas01-09sotheyare2digits).
Hear 1 beep and Light Indicator illuminates green
RecordNewandChangedCodesonProgrammingRecordlocatedonPage17
Hear 1 beep and Light Indicator illuminates green
NOTE:WhenaNEWUSERCODEisset,thedefaultfactorycode(1234)isdeleted
for safety.
RecordNewandChangedCodesonProgrammingRecordlocatedonPage17
123456 08 56785678
Forexample:toaddtheUserID-08toUserCode-5678,enterthefollowing:
4newRe-enter
1Re-enter
Locking and Unlocking
Changing Programming Code
AddingUserCodes
ID
ID
ID
UC UC
UC UC
UC
PC
PC
PC PC
PC
PC
PC
Page 11
DELETE ONE EXISTING OR PRESET USER CODE
TheunitcomeswithafactoryUserID=01forUserCode=1234.
IMPORTANT:Todelete1UserCode,thelockmusthavemorethan1UserCode
in its database.
SET OR CANCEL AUTO LOCK
You can set the lock to automatically close after each time the lock is opened. Time
valuerange=20-900seconds,enterthefollowing:
Youcan“mute”orturnthe“soundon”onyourlockbyenteringthefollowing.
(Factorysettingissoundon).
DELETE ALL USER CODES
IMPORTANT:thiswilldeletetheusercodesbutnottheprogrammingcode,enter
thefollowing
Hear 1 beep and Light Indicator illuminates green
SetAutoLock:
Hear 1 beep and Light Indicator illuminates green
SoundOff(1)-LightIndicatorilluminatesgreen
SoundOn(2)-Hear1beepandLightIndicatorilluminatesgreen
To cancel Auto Lock set the time to 00, enter the following:
CancelTimeValueAutoLock:
Hear 1 beep and Light Indicator illuminates green
Hear 1 beep and Light Indicator illuminates green
2Existing re-enter
5TimeValue
61or2
500
3re-enter
Deleting User Codes
AutomaticLockFunction
Sound On and Off
PC
PC
PC
PC
PC PC
ID
UC
UC
UC
ID ID
1=SoundOff
2=SoundOn
Page 12
WarningsoundsandLEDashesredafter4incorrectcodeattempts:Keypadshuts
downfor30seconds.
To reset the lock to the original factory settings including the Programming Code
andallUserCodesremoveonebatteryfor10seconds.Reinsertthebatteryand
waitforalongandshortbeep.Press3timeswithin3seconds.Thelockwillbeep
andthelightindicatorwillturngreen.
BeepsandLEDashesredfor5seconds.Pleasereplacewithgoodquality
alkaline batteries.
Note:RomovingbatteriesdoesnoteraseactiveProgrammingorUserCodes.
NOTE:Whenbatteryisunderlowvoltage,thelockwillgivethe(LowBatteryWarning:BeepsandLEDashesredfor5seconds).During
thistimeyourlockcanstillwork.Howeveroncethevoltageislowerthan4.3V(calledSuper-LowVoltage),theoperationofthelockingand
unlockingwillnotwork,usermustreplacebatteriesimmediately.
Secure Lock out Period
RestoreFactorySettings
LowBatteryWarning
ConsumerFriendlyMessageGuide
UC
PC
Unlock/Validprogramming: 1 long beep and LED illuminates green
Lock: 2 short beeps and LED illuminates red
InvalidProgramming: 2shortbeepsandLEDashesredtwice
LowVoltage: Beepsfor5seconds
(7/9timesdependsonoperationisunlock/lock)
SuperLowVoltage: 4shortbeepsandLEDashesredfourtimes
4Incorrectcodeentryattempts: 2 short beeps and LED illuminates red each attempt
Poweron: 1 long beep and 1 short beep and LED illuminates green
Chip Reset: 1 long beep and 1 short beep and LED illuminates green
(mayoccurseveraltimesoronceinawhile)
Lock Error: 3longbeepsLEDashesredthreetimes
Repeat operation after Lock Error: 2 short beeps three times LED ashes red six times
Page13
INSTALLATIONTROUBLESHOOTING
Issue Solution
LatchWorkingBackwards-
Lockunlockswhenlock
button is pushed or locks
whenunlockbuttonorcodeis
pushed.
Directionswitchissettoincorrectsetting.
RemovetheInteriorAssemblyandmovethe
switchtotheoppositedirection.
•Checkthatyourswitchissetinthecorrect
position Left or Right Handed door.
If Correct
•RotateTurnknobandreinstallInterior
Assembly.RetestagainwhileholdingInterior
Assemblyinplace.
InteriorAssemblyknobwill
not turn.
Knoborverticaltailpieceisinstalledin
incorrectposition.RemoveInteriorAssem-
bly and reposition the Interior Knob. With the
DeadboltLatchretractedverifythatthetailpiece
isvertical.
Lockwillnotfunction
electronically.
•Checkthatallbatteriesarefreshhighquality
AlkalineBatteries.
•Checkforproperpolarity(+-)ofallbatteries.
•CheckthattheControlWireisattachedtothe
InteriorAssembly.
Lockgiveserrorsignalwhen
opening or locking and Dead-
boltLatchwillnotextendor
retractcompletelywhendoor
is closed.
Unlock door using key or interior knob. While
door is open, check that the Deadbolt Latch
operates smoothly. Check for proper alignment
ofthestrikeplate,adjustasneededtoassure
there is no binding against the Deadbolt Latch.
Deadbolt Latch is sticking. Installationscrewsofthelockmaybetootight
andhavetobeloosened.
•RemoveInteriorAssembly.
•SlightlyloosentheMountingPlatescrews.
•LockandunlockusingtheKey.
•ReattachControlWireandInteriorAssembly.
Page14
EMAIL:[email protected]
WEBSITE:www.honeywellsafes.com
ADDRESS:ConsumerAssistanceDept.
LHLicensedProducts,Inc.860EastSandhillAvenueCarson,CA90746USA
TELEPHONE:US/Canada1-877-354-5457(TollFree)
Mexico01-800-288-2872AfterEnglishvoicerecordingstopsyoumustthenenter800-
860-1677
tocompleteyourcall.(TollFree)
Australia0011-800-5325-7000(TollFree)
Germany/NewZealand00-800-5325-7000(TollFree)
OtherCountriesXX*-310-323-5722(TollChargesApply)
XX*-DialU.S.CountryCoderst
CALLCENTERHOURS:US/Canada7am–5pm(PST**)Mon–Fri(Subjecttochange)
CALLBACKHOURS:OtherCountries7am–8pm(PST**)Mon–Fri(Subjecttochange)
PST**-LocaltimeinLosAngeles,CA,USA
INTERNATIONALCALLBACKHOURS:
IfyouneedtospeakwithaconsumerassistantandcannotcontactusduringtheCall
Centerhoursabove,pleasesendanemailorleaveatelephonemessage,includingyour
Name, Telephone Number and the best time for us to contact you during the Call Back
hoursaboveandwewillmakeoureveryefforttocontactyouandhelpansweranyof
your questions or concerns.
*InsertcorrectCountryCode
**LocalTimebasedonLosAngelesCaliforniaUSA
CONSUMERASSISTANCE
Page15
2-3/8” (60mm) BACKSET
2-3/4” (70mm) BACKSET
THENDRILL1”(25mm)HOLE
INCENTERDOOROFEDGE
2”(50mm)INDEPTH
MARK
FOR1-3/4”
(45mm)
DOOR
DRILL
2-1/8”(54mm)
HOLE
MARK
FOR1-3/8”
(35mm)
DOOR
IMPORTANT!
PLACETEMPLATE
ONHIGHEDGEOF
DOORBEVEL
Page16
BACK OF
TEMPLATE
Page17
My Codes: Date Created
ProgrammingCode (6digits)//
UserCode01 (4-8digits)//
UserCode02 (4-8digits)//
UserCode03 (4-8digits)//
UserCode04 (4-8digits)//
UserCode05 (4-8digits)//
UserCode06 (4-8digits)//
UserCode07 (4-8digits)//
UserCode08 (4-8digits)//
UserCode09 (4-8digits)//
UserCode10 (4-8digits)//
UserCode11 (4-8digits)//
UserCode12 (4-8digits)//
UserCode13 (4-8digits)//
UserCode14 (4-8digits)//
UserCode15 (4-8digits)//
UserCode16 (4-8digits)//
UserCode17 (4-8digits)//
UserCode18 (4-8digits)//
UserCode19 (4-8digits)//
UserCode20 (4-8digits)//
UserCode21 (4-8digits)//
UserCode22 (4-8digits)//
UserCode23 (4-8digits)//
UserCode24 (4-8digits)//
UserCode25 (4-8digits)//
Programming Record
Page18
TheHoneywellTrademarkisusedunderlicensefromHoneywellInternationalInc.Honeywell
InternationalInc.makesnorepresentationsorwarrantieswithrespecttothisproduct.
MDDBKPE-20160115www.honeywellsafes.com
Manufactured by:
LH Licensed Products, Inc.
860EastSandhillAvenue
Carson,CA90746
Lifetime Mechanical and Finish Warranty / 1 Year Limited Electronics Warranty
Thisproductcomeswithalifetimemechanicalandnishwarrantyandaoneyearlimited
electronicswarrantytotheoriginalresidentialconsumeragainstdefectsinmaterialand
workmanshipundernormaluseaslongastheoriginalresidentialpurchaseroccupiesthe
residentialpremisesuponwhichtheproductwasoriginallyinstalled.
ORIGINALRESIDENTIALCONSUMER
Thiswarrantyisnottransferable,andappliestotheoriginalpurchaseronly,aslongastheoriginal
purchaseroccupiestheresidentialpremisesuponwhichtheproduct(s)wasoriginallyinstalled.
Proofofpurchase(originalsalesreceipt)andownershipmustaccompanyallwarrantyclaims.
Allnon-homeownerpurchasers(includingpurchasersforindustrial,commercialandbusinessuse)
arenotcoveredunderthetermsofthiswarranty.
WHATISNOTCOVERED
Thiswarrantyisnullandvoidiftheproductwasusedforpurposesforwhichitwasnotdesigned.
ThiswarrantyDOESNOTCOVERnormalwearandtearofpartsordamageresultingfromanyof
thefollowing:negligentuse,misuseorabuseoftheproduct,orusecontrarytoorinviolationof
writteninstructionsprovidedbyLHLicensedProducts,Inc.Further,thiswarrantydoesnotcover
ActsofGod,suchasre,ood,hurricanesandtornadoes.ThiswarrantyDOESNOTCOVER
scratches,abrasions,deteriorationduetotheuseofpaints,solventsoruseofcleaners
containingabrasives,alcoholorothersolvents,whetherperformedbyacontractor,service
company,oryourself.ThiswarrantyDOESNOTCOVERproduct(s)usedincommercial
applications, used in common area applications, disassembly, repair or alteration by anyone other
than LH Licensed Products, Inc., improper installation or exposure to extremes of heat or humidity.
ThiswarrantyDOESNOTCOVERanylosses,injuriestopersonsorlossofproperty,general
damagesorcosts,andshippingandfreightexpensesrequiredtoreturnproduct(s)to
LH Licensed Products, Inc. LH Licensed Products, Inc. shall not be liable for any indirect,
incidental or consequential damages of any nature relating to this lock. LH Licensed Products, Inc.
isalsonotresponsibleforcostsassociatedwithremovingorreinstallingtheproduct.
ADDITIONALTERMS
LH Licensed Products, Inc. does not authorize any person to create for it any obligation or
liabilityinconnectionwiththeProduct.LHLicensedProducts,Inc.’smaximumliabilityhere
under is limited to the original purchase price of the Product. No action arising out of any claimed
breachofthiswarrantybyLHLicensedProducts,Inc.maybebroughtbytheoriginalresidential
purchasermorethanone(1)yearafterthecauseofactionhasarisen.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Honeywell Safes & Door Locks 8712009 Installation guide

Brand
Honeywell Safes & Door Locks
Model
8712009
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents