Kohler K-R709063-L-SHP Installation guide

Kohler
Brand
Kohler
Model
K-R709063-L-SHP
Type
Installation guide

This manual is also suitable for

Groove
x6
3
1
2
x2
Face
Top View
C
C
D
D
Wall
Screw Cover
Screw Cover
#8-18 x 1-1/2"
x2
Notch
1/32" (1 mm)
Cut Line
"B" Mark
B
B
Top Track
Tin Snips
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
Rubber Mallet
5/16" Masonry
Bit for Tile
5/16"
3/32", 9/64", 5/32"
Sliding Shower Doors
Sliding Bath Doors
1205305**
Hanger Bracket Kit
1221883
Hardware Skin Pack
Top Bumper
1224786
Gasket
1199110
Barrel Nut
1050048-B
Screw
1051142-A
Roller
1044585
Bolt
1077763-A
1031943**
Screw Cover
1056868-A
Screw
1225278
Center Guide
1058626-02**
Bottom Track
1162676-07**
Wall Jamb
[68-13/16" (1748 mm)]
1162676-04** [56-13/16" (1443 mm)]
1077762
Anchor
1199426-01**
Hanger Bracket
Screw
1048208-C
1053530
Insert
1220609-01**
Top Track
1225277
Bottom
Right Bumper
1225276
Bottom
Left Bumper
Bottom Wall
Jamb Notch
#8-18 X 1-1/2"
Bottom Wall
Jamb Notch
#8-32 X 3/8"
8-32 X 1/4"
Serial Number Label
1226469**
Towel Bar Skin Pack
1221364-01**
Towel Bar
#6-20 X 1/2"
1222364-NA**
29-1/2" x 55-19/32"
(749 mm x 1411 mm)
1223197-NA**
23-1/2" x 67-19/32"
(597 mm x 1717 mm)
1222365-NA**
29-1/2" x 67-19/32"
(749 mm x 1717 mm)
Door Panel*
1/4" (6 mm)
Cut Line
"A" Mark
A
A
Insert
Bottom Track
Slide the notched end of the insert into the
groove in the bottom track, grasp the insert and
pull to the opposite end. Trim the insert flush
with the bottom track.
Measure distance "A." On the bottom track,
measure "A." Subtract 1/4” (6 mm) or the width
of a number 2 pencil from "A;" mark and cut the
bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Position the bottom track on the ledge with the
front face evenly spaced (D) along the front
edge, even gaps on each side (C). Tape the
bottom track in place and mark the position.
Important! The bottom track and wall jamb
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use
a coin to match and to transfer the corner radius
of the shower to the wall jamb.
Position the wall jambs over the bottom track.
Plumb using a level. Secure with tape. For each
screw hole, mark the locations or drill a pilot
hole.
Remove the wall jambs. Drill 5/16” holes at each
mark and insert the anchors.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location
with tape.
Install both wall jambs. Secure the wall jambs
with screws. If you are using a power drill, take
care not to strip the screw heads. Install the
screw covers.
Measure distance “B” above the wall jambs.
Subtract 1/32” (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Sliding Shower Door
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT: Leave this manual for the end user.
Read these instructions before installing or using this product. Keep these
instructions in a safe location for future reference.
These instructions can also be found at www.kohler.com
IMPORTANT! Do not cut the top track the same length as the bottom track.
• Two people are recommended for this installation.
• Walls must be within 3/8” (10 mm) of plumb.
• Cover drain with tape to avoid loss of small parts.
• Unpack the door in an area with adequate space and no sharp corners or
surfaces that may cause glass breakage.
• Follow the silicone sealant manufacturer’s instructions for application and
curing time.
1
1220846-2-B
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
1220846-2-B
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
K-R709062, K-R709063, K-R709064
kohler.com
Rails
Bottom
Track
Bumper
Hanger
Bracket
x2
Gasket
x2
8-32 x 1/4"
Barrel
Nut
Hanger
Bracket
No Gap
at Top
#8-32 x 3/8"
x2
Label
Screw
Roller
Label Side
Rollers
Screw
Label
#8-32 x 3/8"
Label
Side
x2
Center of the
Bottom Track
Guide
Bottom Track
Lower the glass.
Raise the glass.
Bottom Track
Guide
Self-Tapping
Screws
Outside of the
Shower
Door
Panel
Corner Protector
x2
x2
Spacers
Back Plate
9/64"
Post
Warranty
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from
date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses
any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for
removal or installation costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or
E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or
by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within
Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.
com in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION
TO THE DURATION OF THIS WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM
ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do
not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or
consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific
legal rights. You may also have other rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty..
Troubleshooting
Symptom: Alignment Recommended Action
1. The top of the door panel is tilted away from
the wall.
A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 21.
2. The bottom of the door panel is tilted away
from the wall.
A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 21.
3. The door panel does not touch the bumper. A. Determine whether the door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
4. The bottom track is miscut or skewed. A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure
proper watertight seal. See step 25.
Symptom: Water Leaks Recommended Action
1. Water leaks between panels. A. When showering, make sure the inside panel is against the showerhead wall.
2. Water leaks between the wall jamb and the
door panel.
A. Adjust the door panel to line up with the wall jamb. Add the optional seal. See step 24 and 25.
3. Water leaks under the bottom track. A. Check for proper silicone sealant application. See steps 24 and 25. Apply more silicone sealant in the leak location.
Symptom: Operation (open/close) Recommended Action
1. The inside and/or outside panel is difficult to
move.
A. Ensure a gap exists between the guide and the door panel. If no gap exists, lower the rollers.
B. Ensure the inside center guide is properly secured with the self-tapping screws. See step 21.
C. Ensure the rollers are properly installed. See steps 14, through 18.
D. Clean any debris in the top track groove.
E. Ensure that the hanger bracket is tight to the glass.
Position the top track over the wall jambs. Either
side of the top track may face out. At each end of
the top track, insert and twist a bumper 1224786
into place over the rails. Slide the bumpers
against the wall jambs.
Install the bottom bumpers. Bumper 1225277
installs on the right side jamb. Bumper 1225276
installs on the left side jamb. Orient each bumper
with the number against the wall jamb.
For both doors, slide a gasket over the top of the
door panel and into each mounting hole. Press
the hanger bracket over the gasket and align the
hanger brackets with the mounting holes.
While pressing downward on the hanger
brackets, use screwdrivers to thread the bolts
into the barrel nuts. Tighten until the hanger
brackets are secured firmly in place.
On the inside panel, assemble a roller to the
middle hole of each hanger bracket. Install
the rollers on the side of the door panel that is
opposite the label.
Lift the inside panel onto the inside track. The
label faces the outside of the shower.
On the outside panel, assemble a roller to the
middle hole of each hanger bracket. Install the
rollers on the same side of the door panel as the
label.
Tilt the top of the outside panel toward you,
carefully lift the bottom edge over the bottom
track, and position the rollers on the outside rail.
Remove the protective corners from the bottom
of both door panels. Position both doors on the
same side of the opening.
Measure to determine the center of the bottom
track and mark. Position and center the guide on
the bottom track and align the door panels with
the guide.
On the inside of the shower, hold the guide
against the bottom track and slide the doors
from wall to wall. If the doors stick, remove the
door and position the rollers in the lower hole to
raise the glass or upper hole to lower the door.
Hold the guide in place and secure with the two
self-tapping screws. Do not overtighten!
Press a spacer onto each back plate and post.
Use a 9/64” hex wrench to assemble the handles
as shown.
Outside the shower, use silicone sealant to seal
along the entire length of the wall jambs and the
bottom track.
Inside the shower, use silicone sealant to seal
along the entire length of the wall jambs and
where the wall jambs meet the bottom track.
2
1220846-2-B ©2014 Kohler Co.
11 12
17
22
13
18
23
16
21
14
19
24
15
20
25
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kohler K-R709063-L-SHP Installation guide

Kohler
Brand
Kohler
Model
K-R709063-L-SHP
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents