2. Dell
  3. B-DCX-4s

Dell B-DCX-4s, PowerConnect B-DCX-4s User guide

  • Hello! I am an AI chatbot trained to assist you with the Dell B-DCX-4s User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the replacement procedure for a blower assembly in a Dell B-DCX-4s?
    What tools are required to replace a blower assembly in a Dell B-DCX-4s?
    How long does it take to replace a blower assembly in a Dell B-DCX-4s?
    What are the signs of a faulty blower assembly in a Dell B-DCX-4s?
    How many blower assemblies should be operating at all times in a Dell B-DCX-4s?
53-1001804-01
January 31, 2010
53-1001804-01
*53-1001804-01*
Blower Assembly
Replacement Procedure
Supporting PowerConnect B-DCX4S Backbone and PowerConnect B-DCX
Backbone
2 Blower Assembly Replacement Procedure
53-1001804-01
Notes, Cautions, and Warnings
NOTE
A NOTE indicates important information that helps you make better use of your computer.
CAUTION
See the safety and regulatory information that shipped with your system. For additional regulatory
information, see the Regulatory Compliance Homepage on www.dell.com at the following location:
www.dell.com/regulatory_compliance.
CAUTION
A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
DANGER
A DANGER indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, Dell
OpenManage and the YOURS IS HERE
logo are trademarks of Dell Inc.; Intel, Pentium, and Celeron are registered trademarks of Intel Corporation
in the U.S. and other countries; Microsoft, Windows, Windows Server, MS-DOS and Windows Vista are either trademarks or registered trademarks
of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Regulatory Model Codes: Brocade DCX-4S, Brocade DCX
Blower Assembly Replacement Procedure 3
53-1001804-01
In this guide
•Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
•Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
•Removing a blower assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
•Replacing a blower assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction
This document provides instructions for replacing a blower assembly in the PowerConnect B-DCX4S and the
PowerConnect B-DCX chassis.
ATTENTION
To ensure continuous adequate cooling for the PowerConnect B-DCX, maintain three operating blower assemblies at
all times except for the brief period when replacing a blower assembly.
The PowerConnect B-DCX4S can continue operating during the replacement if the second blower assembly is
operating.
Time and items required
The replacement procedure for each blower assembly takes less than 5 minutes. The following items are required
for the blower assembly replacement:
• Replacement blower assembly
• Phillips #2 screwdriver
Removing a blower assembly
1. Before removing a blower assembly, verify that the other blower assemblies are functioning correctly. The power
LEDs should be steady green.
2. Use the screwdriver to loosen the captive screws for the blower assembly (Figure 1 or Figure 2.) On the DCX the
screws are at the top and bottom of the assembly and on the DCX-4S they are on the left and right.
3. Support the blower assembly from beneath. Use the handle to remove the blower assembly.
4 Blower Assembly Replacement Procedure
53-1001804-01
FIGURE 1 DCX blower assembly
‘
FIGURE 2 DCX-4S blower assembly
Blower Assembly Replacement Procedure 5
53-1001804-01
Replacing a blower assembly
To replace a blower assembly
1. Orient the blower assembly and slide it into the chassis, pushing firmly to ensure that it is seated.
2. Verify that the power LED displays a green light.
3. Use the screwdriver or your fingers to tighten the captive screws.
6 Blower Assembly Replacement Procedure
53-1001804-01
/