VISUAL COMFORT KW 5640 is a stylish pendant light that offers a versatile lighting solution for various indoor spaces. With its adjustable hanging height and easy-to-install design, this fixture can be effortlessly mounted on a ceiling or canopy, allowing you to customize the lighting ambiance to your preference. KW 5640 features a durable construction and a sleek brass finish, making it a perfect addition to modern or contemporary decors.
VISUAL COMFORT KW 5640 is a stylish pendant light that offers a versatile lighting solution for various indoor spaces. With its adjustable hanging height and easy-to-install design, this fixture can be effortlessly mounted on a ceiling or canopy, allowing you to customize the lighting ambiance to your preference. KW 5640 features a durable construction and a sleek brass finish, making it a perfect addition to modern or contemporary decors.
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (A) from canopy (G) by removing collar
ring (H).
3. Install mounting plate (A) to the junction box and secure with
mounting screws (D).
4. Feed electrical wire through bottom rod (J) and connect to fixture (K).
5. Continue feeding wire through collar ring (H), canopy (G) and top
rod (I).
6. Holding fixture upright, slide collar ring (H) and canopy (G), down and
rest on bottom rod (J). Then connect top rod (I) to bottom rod (J).
NOTE: Slide components down slowly to avoid damages.
7. Hang fixture swivel ball (F) to the center of mounting plate (A) and
secure with set screw (E) using provided wrench. See diagram 1.
8. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8".
9. Connect supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 2). Tighten
NOTE: It is imperative that the fixture is grounded.
Brassica Mini Pendant
Item # KW 5640
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers
NOTICE:
US
M
L
I
D
S
E
T
Option 1: Canopy Mounted Driver
B
B
C
wrench
wrench
Diagram 2
Diagram 1
A
D
F
E
E
H
K
J
I
I
G
Brassica Mini Pendant
Item # KW 5640
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
10. Connect driver (C) input neutral wire (white) to the supply neutral wire
(usually white) using wire nut (B).
11. Connect driver (C) input hot wire (black) to the supply hot wire (usually
black) using wire nut (B).
CAUTION: Do not reverse the hot and neutral connections.
12. Connect fixture neutral wire (black) to driver (C) output wire (black)
using wire nut (B).
13. Connect fixture hot wire (red) to driver (C) output wire (red) using
wire nut (B).
CAUTION: Do not reverse the hot and neutral connections.
14. Make sure all wire connections are tight, then carefully tuck into the
junction box.
15. Insert driver (C) into mounting plate bracket.
16. Install canopy (G) to mounting plate (A) and secure with collar
ring (H).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
Option 1: Canopy Mounted Driver
B
B
C
wrench
wrench
Diagram 2
Diagram 1
A
D
F
E
E
H
K
J
I
I
G
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Place driver (C) into ceiling and route all wires through one of the
knockouts in the junction box.
3. Remove mounting plate (A) from canopy (G) by removing collar
ring (H).
4. Install mounting plate (A) to the junction box and secure with
mounting screws (D).
5. Feed electrical wire through bottom rod (J) and connect to fixture (K).
6. Continue feeding wire through collar ring (H), canopy (G) and top
rod (I).
7. Holding fixture upright, slide collar ring (H) and canopy (G), down and
rest on bottom rod (J). Then connect top rod (I) to bottom rod (J).
NOTE: Slide components down slowly to avoid damages.
8. Hang fixture swivel ball (F) to the center of mounting plate (B) and
secure with set screw (E) using provided wrench. See diagram 1.
9. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8".
10. Connect supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 2). Tighten
NOTE: It is imperative that the fixture is grounded.
Brassica Mini Pendant
Item # KW 5640
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers
NOTICE:
US
M
L
I
D
S
E
T
Option 2: Ceiling Mounted Driver
wrench
Diagram 2
Diagram 1
E
A
B
C
D
I
wrench
F
E
H
K
J
I
G
Brassica Mini Pendant
Item # KW 5640
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Connect fixture neutral wire (black) to driver (C) output wire (black)
using wire nut (B).
12. Connect fixture hot wire (red) to driver (C) output wire (red) using
wire nut (B).
13. Connect supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 2). Tighten.
NOTE: It is imperative that the fixture is grounded.
14. Connect driver (C) input neutral wire (white) to the supply neutral wire
(usually white) using wire nut (B).
15. Connect driver (C) input hot wire (black) to the supply hot wire (usually
black) using wire nut (B).
CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the
junction box.
17. Install canopy (G) to mounting plate (A) and secure with collar
ring (H).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
Option 2: Ceiling Mounted Driver
wrench
Diagram 2
Diagram 1
E
A
B
C
D
I
wrench
F
E
H
K
J
I
G
-
1
-
2
-
3
-
4
VISUAL COMFORT KW 5640 is a stylish pendant light that offers a versatile lighting solution for various indoor spaces. With its adjustable hanging height and easy-to-install design, this fixture can be effortlessly mounted on a ceiling or canopy, allowing you to customize the lighting ambiance to your preference. KW 5640 features a durable construction and a sleek brass finish, making it a perfect addition to modern or contemporary decors.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VISUAL COMFORT CS 2605 User manual
-
VISUAL COMFORT PCD 2200 User manual
-
VISUAL COMFORT S 2212 User manual
-
-
-
-
-
-
-
Other documents
-
circalighting CD2020 Flore Double Library Wall Light Operating instructions
-
Ralph Lauren RL 2729 User guide
-
circa LIGHTING TOB 5739 User manual
-
circa LIGHTING PCD 5115 User manual
-
-
circalighting ARN5500 Installation guide
-
Visual Comfort Studio CHC 1474GI-NP Installation guide
-
-
circa LIGHTING JN 4240 User manual
-
circa LIGHTING PB 5151 Installation guide
