2. Computers & electronics
  3. Audio & home theatre
  4. Loudspeakers
  5. Ampeq
  6. SVT-7PRO
SVT-7PRO

Ampeq SVT-7PRO User guide

  • Hello! I am an AI chatbot trained to assist you with the Ampeq SVT-7PRO User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
SVT-7PRO
Quick Start Guide
2
SVT-7PRO
SPEAKER OUTPUTS TUBE DIRECT
OUTPUT PRE-EQ
POST-EQ AUX INPUT
(STEREO)
600 W @ 8 1000W @ 40,1/2$'
SEND
FX
RETURNFOOT SWITCH TUNER OUTPOWER AMP IN PREAMP OUT
PATC H
FUSE T10AH 250V
LIFT
GND
-40dB
0dB L
R
CLASS 2 WIRING
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16 0
1
2
3
HIGH
FREQUENCY
ATTENUATOR FULL RANGE
INPUTS
OFF –6 0
SPEAKER OUTPUTS TUBE DIRECT
OUTPUT PRE-EQ
POST-EQ AUX INPUT
(STEREO)
600 W @ 8 1000W @ 40,1/2$'
SEND
FX
RETURNFOOT SWITCH TUNER OUTPOWER AMP IN PREAMP OUT
PATC H
FUSE T10AH 250V
LIFT
GND
-40dB
0dB L
R
CLASS 2 WIRING
-db
LEVEL CONTROL
4
5
6
7
8
8
9
10
11
12
16 0
1
2
3
HIGH
FREQUENCY
ATTENUATOR FULL RANGE
INPUTS
OFF –6 0
POWER HANDLING:
800W RMS (MONO)
400W RMS (DUAL)
IMPEDANCE:
4 OHMS (MONO)
8 OHMS (DUAL)
PIN 1+ = POS (+)
PIN 1- = NEG (-)
4X10-DUAL MODE ONLY
4X10-DUAL MODE
MONO INPUTS
-or-
SPEAKER OUTPUTS TUBE DIRECT
OUTPUT PRE-EQ
POST-EQ AUX INPUT
(STEREO)
600 W @ 8 1000W @ 40,1/2$'
SEND
FX
RETURNFOOT SWITCH TUNER OUTPOWER AMP IN PREAMP OUT
PATC H
FUSE T10AH 250V
LIFT
GND
-40dB
0dB L
R
CLASS 2 WIRING
Speaker Cabinet
Standard Setup
Parallel Setup
Speaker Cabinet A Speaker Cabinet B
Daisy Chaining
Speaker Cabinet A Speaker Cabinet B
Note: Use same impedance cabinets in parallel setups and when daisy-chaining
What’s in the Box
SVT®-7PRO Amplifier, Power Cable, Quick Start Guide.
Hookup Diagrams
3
6
5
2
G
G
AIN
AIN
COMPRE
COMPRE
S
S
SION
SION
UL
UL
T
T
R
R
A HI
A HI
UL
UL
T
T
R
R
A LO
A LO
FX MIX
FX MIX
DRY
DRY
WET
WET
MASTER
MASTER
POWER
POWER
BA
BA
S
S
S
S
MID
MID
R
R
ANGE
ANGE
FREQUENCY
FREQUENCY
TREBLE
TREBLE
ON
ON
-15dB
-15dB
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
0
0
1
1
2
2
3
3
4
4
5
5
10
10
0
0
10
10
T
T
H
H
R
R
E
E
SH
SH
MUTE
MUTE
P
P
E
E
A
A
K
K
M
M
U
U
TE
TE
SIG
SIG
N
N
A
A
L
L
INPUT
INPUT
PHONES
PHONES
1 12 134 8
9 14
11
10
73
SPEAKER OUTPUTS TUBE DIRECT
OUTPUT PRE-EQ
POST-EQ AUX INPUT
(STEREO)
600 W @ 8Ω 1000W @ 4Ω MIN LOAD
SEND
FX
RETURNFOOT SWITCH TUNER OUTPOWER AMP IN PREAMP OUT
PATCH
FUSE T10AH 250V
LIFT
GND
-40dB
0dB L
R
CLASS 2 WIRING
17 19 21
15 16 18 20 22
Front & Rear Panels
4
Front & Rear Panel Descriptions
1. 1/4" Inputs: Connect a passive or active instrument to the input jack.
2. Peak/Mute LED: Indicates when the input signal is clipping or when the mute is engaged.
3. Mute Switch: Mutes all outputs except for Tuner Output.
4. Pad: Reduces input level by 15 dB.
5. Thresh LED: Lights when the signal triggers the compressor threshold.
6. Compression: Controls the amount of compression applied to the input signal.
7. Gain Knob: Varies the intensity of the signal sent to the preamplifier.
8. Ultra Hi/Ultra Lo Switches: Boosts high or low frequencies.
9. EQ Knobs: Boost or cut the levels at certain frequencies to enhance the sound.
10. Frequency Select Knob: Selects the frequencies affected by the Midrange EQ knob.
11. FX Mix Knob: Controls the wet/dry signal for the FX Loop.
12. Master Knob: Controls the overall speaker output and headphone levels.
13. Phones Output: Combination playback of the 1/4" Input and Aux Input.
14. Power Switch/Power LED: Turns the power on/off. The LED indicates power on/off.
15. Power/Voltage Select Switch: Input socket for power cable and switch for local AC voltage selection.
16. Foot Switch Input: Control the Mute and FX functions using a footswitch.
17. Speaker Outputs: Speakon® / 1/4" TS outputs for connecting speakers.
18. Patch Input/Output: Pwr Amp In bypasses the internal preamp. Pre Amp Out feeds an external amplifier
or powered speaker.
19. Tube Direct Output and Switches: XLR line level output. Switches to optimize output to a mixer or
recorder.
20. FX Loop Input/Output: Connect the input and output of a external FX processor.
21. Aux Input: Input for an MP3 player or other music source.
22. Tuner Output: Feeds an external tuner.
Getting Started
1. Read and understand the included “Important Safety Instructions.”
2. Make sure the power switch is off before making any connections.
3. Push the line cord securely into the amplifier’s IEC connector and plug the other end into a grounded AC
outlet. The amplifier may accept the appropriate voltage, as indicated near the IEC connector.
4. Connect an instrument to the SVT-7PRO Input jack with a 1/4" instrument cable. Connect speaker cables
to speaker cabinets with 1/4" TS or Speakon ends, depending on model.
5. With all volume controls fully off, turn the amplifier on by pressing the power switch to the on position.
6. While playing the instrument, adjust the Gain and Master knobs to the preferred level.
7. Adjust the EQ knobs to taste.
5
SVT-7PRO
Output Power Rating 600W RMS @ 8 (5% THD)
1000W RMS @ 4 (5% THD)
Maximum Gain 72dB
Power Requirements ~100-120V AC, 50-60 Hz, 1050W
~200-240V AC, 50-60 Hz, 1050W
Size (H x W x D) 4.0 x 15.6 x 11.5 in
102 x 369 x 292 mm
Weight 15.5 lb/7.03 kg
All specifications subject to change
Technical Specifications
www.ampeg.com
Yamaha Guitar Group, Inc.
26580 Agoura Road, Calabasas, CA 91302-1921 USA
Part No. 40-00-0529 Rev. B
WARRANTY AND SUPPORT
Visit WWW.AMPEG.COM to...
(1) ...identify WARRANTY coverage provided in your local market. Please keep your sales
receipt in a safe place.
(2) ...retrieve a full-version, printable OWNER’S MANUAL (English only) for your product.
(3) ...REGISTER your product.
(4) ...CONTACT Technical Support, or call
818-575-3600.
© 2021 Yamaha Guitar Group, Inc. All rights reserved.
Ampeg and SVT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S. and/or other jurisdictions. Speakon is a
registered trademark of Neutrik AG Corporation.
There are various types of fuses, and replacing them with different types may cause malfunction, electric shock, or fire. Be sure to con-
firm you are replacing the correct fuse with electrical rating and specifications.
Each number and symbol represent the following:
Example: T3AL250V
T, ⃝A, L, and ■V are shown below.
Symbol indicating relative fusing time / current characteristics T: Time lag type, F: Fast-acting type.
⃝A: Rated current
Symbol indicating the blocking capacity L: Low cutoff capacity, E: Medium cutoff capacity, H: High cutoff capacity.
■V: Rated voltage
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: Ampeg SVT-7PRO
Responsible Party - U.S. Contact Information:
Yamaha Guitar Group, Inc.
26580 Agoura Road
Calabasas, CA 91302-1921
(818) 575-3600
https://ampeg.com/
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Serial No.: ____________________________________
/