PDQ 6W199 User manual

6W199
Brand
PDQ
Model
6W199
Type
User manual

PDQ 6W199 is an electrified exit device trim that provides secure and convenient access control for various applications. With its versatile design, it can be configured for fail-safe or fail-secure operation, adapting to your specific security requirements. The trim features easy installation with clear instructions and includes wire saddles for secure wire management. It operates on 12-24VDC/VAC power, ensuring compatibility with most access control systems.

PDQ 6W199 is an electrified exit device trim that provides secure and convenient access control for various applications. With its versatile design, it can be configured for fail-safe or fail-secure operation, adapting to your specific security requirements. The trim features easy installation with clear instructions and includes wire saddles for secure wire management. It operates on 12-24VDC/VAC power, ensuring compatibility with most access control systems.

6W199 Electrified Exit Device Trim
INSTALLATION INSTRUCTIONS Phone: 833-2-PDQTEC | www.pdqlocks.com
639412 Rev0 – 3-21-22
1. REMOVE HEAD COVER
AND RAIL FILLER PLATE
• Remove (4) screws, push latch into
device to remove head cover
RAIL FILLER PLATERAIL FILLER PLATE
HEAD COVERHEAD COVER
2. REMOVE HOLDING SCREW
AND RAIL
• Remove screw securing backplate to rail
• Remove backplate from rail HOLDING SCREWHOLDING SCREW
3. INSTALL WIRE
SADDLES ONTO
BACKPLATE
• Secure (3) wire saddles to
backplate
4. CONFIGURE TRIM FOR FAIL
SAFE OR FAIL SECURE
• Fail Secure: Power to Unlock (Default)
• Outside trim is locked when power is
OFF, and unlocked when power is ON
• Fail Safe: Power to Lock (Cut White Loop)
• Outside trim is locked when power is
ON, and unlocked when power is OFF.
POWER WIRES ARE
BLUE OR YELLOW
WHITE LOOP
POWER WIRES ARE
BLUE OR YELLOW
WHITE LOOP
(3) Mounting Locations(3) Mounting Locations(3) Mounting Locations
RAIL
639412 Rev0 – 3-21-22
6W199 Electrified Exit Device Trim
INSTALLATION INSTRUCTIONS Phone: 833-2-PDQTEC | www.pdqlocks.com
5. INSTALL TRIM AND DEVICE
• Refer to trim and exit device installation
instructions and templates.
• For ISMC option only:
• Install nonpolar blue or yellow power
wires into positions 1 & 2 on housing
• If REX and/or LM option is selected,
install wires in existing housing on exit
device. Otherwise, install wires in
provided 8-pin housing
ELECTRICAL SPECIFICATIONS
Keep operating voltage at +/- 10% of rated voltage
Important Notes:
Power must be applied to lock for a minimum of 5 seconds. It may be necessary to adjust the default time
delay on your system. Device may not lock reliably if powered for less than 5 seconds
To convert from fail secure to fail safe, cut the white wire loop. No need to cover the cut wires. To revert to
fail secure, reconnect the white wires with a suitable wire nut for two 24AWG wires.
Kit includes components to safely route wires through 6300/6400 exit device. Failure to use this kit will
result in pinched wires.
Vin Max Inrush Current Standby Current
12-24 VDC 1.0A 5mA
12-24 VAC 1.0A 15mA
ISMC OPTION:
TERMINAL INSERTION
END SHOWN
  • Page 1 1
  • Page 2 2

PDQ 6W199 User manual

6W199
Brand
PDQ
Model
6W199
Type
User manual

PDQ 6W199 is an electrified exit device trim that provides secure and convenient access control for various applications. With its versatile design, it can be configured for fail-safe or fail-secure operation, adapting to your specific security requirements. The trim features easy installation with clear instructions and includes wire saddles for secure wire management. It operates on 12-24VDC/VAC power, ensuring compatibility with most access control systems.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents