Dryflow HDDFJFPLH-GRP Operating instructions

Brand: Dryflow

Model: HDDFJFPLH-GRP

Type: Operating instructions

Dryflow HDDFJFPLH-GRP is a high-speed, energy-efficient hand dryer with a hygienic "no-touch" design. It features a tamper-proof timer to prevent misuse and an antibacterial coating on the air filter cover for added hygiene. Choose between "hot" or "cool" air and set the heater to "auto" or "all time" heating.

Instructions

Jet Force Plus Hand Dryer

Instructions

Thank you for your purchase. Please read these instructions before

installation and/or use and keep in a safe place for future reference

Dryflow, 7 Riverside Court, Don Road, Sheffield, S9 2TJ. UK.

+44 (0)114 3540047 | [email protected] | www.dryflow.co.uk

HOW TO USE................................................

TROUBLESHOOTING.....................................

ROUTINE CLEANING....................................

WARNING.....................................................

FEATURES......................................................

CONTENTS

INSTALLATION METHODS.............................

COMPONENTS.............................................

SPECIFICATION............................................

HOW TO USE

TROUBLESHOOTING

HOW TO DRY THE HANDS

Place the hands in to

the drying cavity Slowly draw the hands

out Stop when the hands

are dry

If the following problems occur, please perform these checks and actions

Problem Check Action

No air blows when

hands are inserted

The unit doesn’t stop

running when the

hands are removed

No hot air comes out

the hand dryer

The indicator light is

flashing

If the above actions do not work, turn off the power and the ground-fault circuit breaker and contact the

company you bought the hand dryer from for further advice.

Do the display indicators

light up?

Is the power switch on?

Are the hands fully inserted

to activate the sensor?

Is the sensor blocked by dirt

or dust?

Is the heater switch on the

"hot"

setting?

Is the heater setting switch on

"A uto Heating" setting or "All

Time Heating" setting?

Is the heater element faulty?

- Turn the heater switch to the ""hot" setting.

- Turn the heater setting switch to the "All Time Heating" setting.

- Turn the power switch off. Remove the front cover, then

remove the cover of the teminal box. Check the 3 fuses

(terminal connector) for any faults.

Check for problems with the

power supply

Turn the power switch off. Check all the indicators in the

display indicator have gone off (after around 40

seconds), then turn on the power switch again.

Turn the power switch off. Wait for the indicator lights

to go out then remove any dirt or dust from the sensor.

- Turn the ground fault circuit breaker on

- Turn the power switch on

- Put the hands all the way into the cavity to activate

the sensor.

ROUTINE CLEANING

WARNING If you don’t use this unit properly or

follow the safety guidelines carefully, it

may lead to serious personal injury

Prohibited

Do not place

near excessive

water sources

Disassembling

is prohibited

instructions

with all

comply

Please

Earth

grounding

connection

• Do not open the front panel, otherwise this may cause an

electric shock.

• Do not install the hand dryer too close to excessive water sources

such as bathtubs, showers and basins, otherwise this may cause

electric shock or unit malfunction.

• Do not modify or disassemble the unit unnecessarily as this may

lead to fire, electric shock or personal injury.

• Use a single phase AC 220-240V/50/60Hz power supply.

• Use within the required voltage, as voltage exceeding 220V +

10% will cause the unit to fail. Using an incorrect power supply may

lead to fire, electric shock or unit malfunction.

• Ensure each unit has its own dedicated power cable that is not

shared with any other appliance to avoid the risk of fire.

• Turn off the power switch before any maintenance or cleaning

takes place on the hand dryer. Otherwise this may cause an

electric shock.

• Ensure the unit is properly grounded. Otherwise it may cause an

electric shock or short circuit.

• Installation work should be done by a qualified technician to

avoid the risk of electric shock or fire.

• Be sure to install a residual current circuit breaker, otherwise this

may cause an electric shock.

• Use contact points that are at least 3mm apart

- Please only use products that comply with your countries Safety

Standards.

- Recommended residual current circuit breaker (for ground fault

protection). (Use a single phase 2-line, AC 220-240V50/60Hz cable

with a 20A rated current, 15mA-type rated operating current).

Cleaning the main body

Perform regularly

Emptying and cleaning the drain tank

Check at least once a week

Cleaning the air filter

Perform approx once a week

• Clean the unit with a damp soft cloth.

If the unit gets excessively dirty, clean with a soft cloth dampened with a neutral

detergent, then use a dry soft cloth to finish.

• Remove dirt and dust from the sensor to prevent malfunction.

WARNING

• Before you clean the unit,

turn off the power switch.

• Do not use excessive

amounts of water on the unit.

Caution

• Wear gloves when cleaning

Note

• Only use neutral detergent / cleaning agents

• Do not use thinner, acidic or alkaline cleaners, or a nylon

brush, otherwise this may damage the hand dryer cover

• Only use alcohol (disinfecting concentration below 83%) on

the hand drying area, nowhere else on the hand dryer.

• If using chemical cloths, be sure to read their instructions

before use.

• Strong disinfecting agents may damage the unit.

• The antibacterial coating is effective when

bacteria is exposed to the coated surfaces

• The antibacterial coating is less effective

when the surfaces are dirty

• Water blown off the hands will enter the drain tank.

• It is advisable to check the drain tank regularly to avoid exceeding

the full level.

• Leaving water in the drain tank for a significant period of time could

lead to unpleasant smells.

Pull the drain tank out in a horizontal

direction

This ensures that the water

doesn’t spill or splatter

Full Level Drain Tank

Cover

Full Level

1. Open the cover and empty the

water.

Pull the cover up with your fingers in

the direction of the arrow on top of

the cover, then remove the cover

completely.

2. Wash out the interior of the drain

tank.

3. Close the drain tank cover and

replace it back in the unit.

Check that the drain tank is firmly

inserted back in place.

Add 200ml of water through the

drain hole to prevent it from

getting clogged.

Continue to use the unit after

confirming the drain tank is in

place.

Drain Hole

• Remove the air filter.

Pull the air filter out by the

handle.

Handle

1. Cleaning the air filter.

Beat it lightly by hand or use a

vacuum cleaner.

If it is very dirty, wash with cold or

warm water*.

2. Replace the air filter into the

unit.

Make sure it is inserted all the

way into the unit until it stops. If it

is not in place, dirt and dust will

enter the unit and shorten its

service life.

Air Filter

Note

• *If you wash the air filter with water you need to

make sure it is completely dry before replacing it

to the unit.

• Do not expose the filter to fire.

WARNING

FEATURES

INSTALLATION METHODS

• “No touch” hand drying ensures complete hygiene.

• High-speed, low cost hand drying.

• A tamperproof timer prevents misuse*.

• No need for paper towels; ease of maintenance.

• Air filter with antibacterial coating on cover.

*To prevent misuse, the tamperproof built in timer will automatically stop the unit after 30 seconds of

continuous sensor activation. Once the hands are removed and put back into the drying cavity the

hand dryer will activate again as normal.

If you don’t use this unit properly or

follow the safety guidelines carefully, it

may lead to serious personal injury

Prohibited

instructions

with all

comply

Please

• Always use the unit with the drain tank and air filter in place. If water

is allowed to enter the inside of the unit it may cause short circuit or

electric shock.

• If the unit does not start or works abnormally, turn off the power

switch and ground fault breaker and contact the place where you

purchased the unit to arrange inspection or repair.

• Do not use in the following places:

- Where the unit may come into direct contact with excessive water.

- Where the unit is under direct or strong sunlight (this may cause the

sensor to malfunction).

- Where condensation may form within the unit.

• Safety precautions before installing the unit:

- Do not attempt to install the unit with the power on, otherwise this

may cause an electric shock.

- The installation location should be strong enough to support the unit.

The unit should be installed firmly to the wall. Otherwise this may lead

to personal injury if the unit falls.

• Ensure children are not allowed to play with the

hand dryer and are supervised at all times.

INSTALLATION METHODS COMPONENTS

SPECIFICATION

Rated Voltage

Rated Frequency

Rated Power

Motor Power

Ingress Protection

Air Speed

Drying Time

Overall Size (mm)

AC220-240V

AC110-127V

50/60HZ

800W +

(PTC 850W)

800W

IPX4

90m/s

10s

300 x 220 x 687

Switch Panel

Power Indicator Self-Check Indicator

Blue LED Lights

Hand Drying Area

Sensor

Main Body

Drain Hose

Air Filter

Drain Tank

Full Level Indicator

• Before starting to operate the hand dryer.

- Turn on the power switch (located on the lower part of the switch panel).

- The power indicator light at the top of the hand dryer will light up.

- The blue LED lights in the hand dryer cavity will light up.

• PTC heater control: There are 2 switches in the upper part of the switch panel.

- The switch to the right allows for a “Hot” or “Cool” setting. This turns the heater element on or off, respectively.

- When the “Hot” setting is chosen, the switch to the left allows for an “Auto Heating” or “All Time Heating” setting.

1. When set to “Auto Heating” the heater element is automatically activated when the ambient temperature of the room is

less than approx. 25oC and automatically inactive above this temperature.

2. When set to “All Time Heating” the heater element is active at all times no matter what the ambient temperature of the

room is.

INSTALLATION METHODS INSTALLATION METHODS

Dryflow HDDFJFPLH-GRP Operating instructions

Dryflow HDDFJFPLH-GRP Operating instructions

Dryflow HDDFJFPLH-GRP Operating instructions

Other documents