2. Aiphone
  3. IS
IS

Aiphone IS Install Manual

  • Hello! I am an AI chatbot trained to assist you with the Aiphone IS Install Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I change the IP address of the IS-CCU?
    How do I create a new paging zone?
    How do I register a new station?
    How do I program a door/sub to call a master?
    How do I add a station to a zone?
    How do I update the system with all the changes?
IS SERIES
Local System
QuikStart Programming Guide
This is an abbreviated programming manual, addressing basic program settings for an
IS Series Local System.
A complete set of instructions (IS Series Installation Manual / IS Series
Operation Manual / IS Series Settings Manual)
can be found on the CD provided with the IS-CCU Central Control Unit.
ATTENTION:
#95501
11-1/16"
16-3/4"
18-15/16"
3-3/8"
'22568%67$7,21
9,'(2$8',2
,6&&8
&;
&;
&;&; &;
&; &; &;
,65&8
00 '
0
0 '
0$67(567$7,21
3$287387
3 3 /3 3 /
&217$&7287387
/ / / /
P
,66&8
0;0;'
' 0;0;
,30;
,3
0;
,3
,6,3&
$OOWKHSRUWVH[FHSW>/$1@DUHQRW
'R127FRQQHFWWR/$1QHWZRUN
IRU/$1QHWZRUN
9,'(2287387
9 9
ȭ㹼ȭ
&+,0(,1387
6(
&217$&7,1387
// 6( 6( 6( %%
675,3/(1*7+
32:(5
P
$&7
67$786
/LQN
0$&$''5(66
ȭ㹼ȭ
/$1
(7+(51(7
'&9
675,3/(1*7+
IS-CCU
0314
How-To
Video Link
Programming Videos
2 | IS Series Local System Programming Guide
All steps are REQUIRED for programming the system unless marked OPTIONAL. Refer to the IS Local System
Setting Manual on the CD included with the IS-CCU for complete programming information.
IMPORTANT:
If this IS-CCU will be used with an IS-IPC, please refer to the IS-IP Setting Manual for programming instructions.
Step 1: Change PC Network Settings (OPTIONAL)
-
Allows the PC to communicate with the IS-CCU.
Step 2: Log in to the IS-CCU
- Entering name and password for the rst time.
Step 3: Change Network Settings (OPTIONAL)
- Putting the IS-CCU on the network for ease of programming.
(Refer to the IS Series Local Setting Manual when using a IPV6 network)
Step 4: Change Administrator Settings (OPTIONAL)
- Creating a new name and password.
Step 5: Register Paging Zones (OPTIONAL)
- Creating paging zone name(s).
Step 6: Control Unit Composition
- Dening what control units are in the system.
Step 7: Register Stations
- Dening what stations are in the system by assigning station numbers and names.
Step 8: Advanced Station Settings
- Dening which doors/subs call which masters.
Step 9: Zone Setting (OPTIONAL)
- Dening which stations will be in each paging zone.
Step 10: Time and Date Setting
- Updating the time and date displayed on the master(s).
Step 11: Updating the System
- Uploading all settings to the IS-CCU.
The IS-CCU default IP address is https://192.168.0.30. The PC will need to be set in the same subnet in order to
connect to the IS-CCU.
A. Open Control Panel
- Windows XP
®
(Classic View) Network Connections Double click Local Area Connection to open
Connection Status window.
- Windows 7
®
(Category View) Network and Internet View network status and tasks Click
Local Area Connection to open the Local Area Connection Status window.
B. Click the Properties button to open Local Area Connection Properties window.
C. Scroll down and left click Internal Protocol (TCP/IP) then click Properties button to open Internet Protocol
Properties window.
D. Select the Use the following IP address radio button. Type in the IP address 192.168.0.100 (the last number
can be any valid host address except 30) and change the subnet mask to 255.255.255.0. Click [OK].
E. Click [OK] in Connection Properties window to accept these changes.
Step 1: Change Network Settings (OPTIONAL)
GENERAL OVERVIEW:
3
A. Open a web browser and point the address bar to https://192.168.0.30 and hit Enter.
Note: ensure that https (for security) is being used in the address bar.
B. Asecuritycerticateerrormessagewillappear.Click“Continuetothiswebsite.”
C. Choose preferred language (see Figure 2.1).
D. LogintotheunitusingthedefaultadministratorID“aiphone”,anddefaultpassword“aiphone”(seeFigure 2.2).
Figure 2.1: Language Selection Figure 2.2: Log in
E. When System conguration appears, ensure that Local system is checked under (see Figure 2.3). If it is not, check
the Local system radio button and click
Temporarily stored
to save the setting.
A. Select Network setting from the menu on left.
B. The default option is DHCP. Aiphone recommends assigning a static IP address by
clicking the Static IP Address radio button and entering a unique IP Address and Subnet Mask (see Figure 3.1).
C. Click
Temporarily stored
to save changes.
Figure 2.3: System Conguration
Figure 3.1: Network Setting
IMPORTANT:
When changes are made while programming, click
Temporarily stored
to save data prior to leaving
each screen. The saved data will be applied to the system when the system is updated.
Step 2: Log in to IS-CCU
Step 3: Change Network Settings (OPTIONAL)
Note: Refer to the IS Series Local Setting Manual when using a IPV6 network.
Step 1
Video Link
Step 2
Video Link
4 | IS Series Local System Programming Guide
A. Select Administrator setting from the menu on left.
B. The default ID and password are both aiphone. Enter a New administrator ID
and/or New Password if desired (see Figure 4.1).
C. Click
Temporarily stored
to save changes.
Figure 4.1: Administrator Setting
A. Select Zone registration from the menu on left.
B. Enter a Zone name for each paging zone required (see Figure 5.1). The system can
haveupto99zones.Eachzonecanhaveanycombinationofmasters,rooms,doors,orpagingampliers.
C. Click
Temporarily stored
to save changes.
Figure 5.1: Zone Registration
A. Select Control units composition from the menu on left.
B. Select which units will be used (see Figure 6.1).
The IS-CCU control unit will support up to 4 IS-RCU and up to 2 IS-SCU.
C. Click
Temporarily stored
to save changes.
Figure 6.1: Control Units Composition
Step 4: Change Administrator Settings (OPTIONAL)
Step 5: Register Paging Zones (OPTIONAL)
Step 6: Control Units Composition
Step 5
Video Link
Step 6
Video Link
5
A. Select Registering stations from the menu on left.
B. The Registering stations table will be populated based on the settings made in Step 6.
Enter a Station number and Station name for each door/sub/master unit. In the
Station type column, use the drop-down list to identify the type of station connected (see Figure 7.1).
C. Click
Temporarily stored
to save changes.
Figure 7.1: Registering Stations
A. Select Advanced station settings from the menu on left.
B. The Advanced station settings table is populated based on the stations registered in
Step 7 (see Figure 8.1).
D. Click on
Called stations
.
Figure 8.1: Advanced Station Settings
C. To program a door/sub, check the corresponding box and click
Advanced settings
. A new window will open
(see Figure 8.2).
Figure 8.2: Advanced Settings
Step 7: Registering Stations
Step 8: Advanced Station Settings
IMPORTANT:
Advanced station settings is a required step to complete the programming process.
Step 7
Video Link
Step 8
Video Link
6 | IS Series Local System Programming Guide
E. Themasterstationsprogrammedtobecalledwillbelisted.Whenprogrammingforthersttime,thelistwillbe
blank. Select the Call priority level from the drop-down list (see Figure 8.3). Click on
Reference
to open a new
window to select the masters to be called (see Figure 8.4).
Figure 8.3: Advanced Settings - Called Stations
F. Check the box beside the master(s) for the door station to call, then click
Close
. A maximum of 20 masters can
be chosen for any given door station (see Figure 8.4).
Figure 8.4: Advanced Settings - Called Stations
Figure 8.5: Advanced Settings
Figure 8.6: Advanced Settings
Step 8: Advanced Station Settings (continued)
G. The Advanced settings window will now display the masters that will be called (see Figure 8.5). If a master was
selected in error, check the box next to that master and click
Delete
to remove it from the list. Once the list is
correct, click
Close
.
H. Click
Other
in the Advanced settings window (see Figure 8.2). A new window will open.
I. In the Advanced settings, Video door station, Other window, choose which settings need to be changed from the
default settings. Upon making changes, click
Close
(see Figure 8.6).
7
J. Close the Advanced settings windows to get back to the main Advanced station settings window.
K. Repeat steps C through J for all video door stations, audio door stations, and room stations.
L. Click
Temporarily stored
to save changes.
A. Select Zone setting from the menu on left.
B. Select the
Zone number from drop-down list (see Figure 9.1), then click
Reference
.
A new window will appear.
Figure 9.2: Stations to Add to Zone
C. Check the box beside each station to add to the selected zone (see Figure 9.2).
D. Click
Close
.
Step 8: Advanced Station Settings (continued)
Step 9: Zone Setting (OPTIONAL)
IMPORTANT:
Ifconnectingan8ΩspeakertotheIS-RSroomstation,clickonthe
Other
button and select External speaker
from the new window. If the scan monitor function is required for a master, select the master(s) and click on
Advanced settings
to program this feature.
Figure 9.1: Zone Setting
IMPORTANT:
Ifapagingamplieristobeincludedinazone,clickthe
Reference
button to the right of PA output and select the
paging output to be included. The PA output must have been named in Registering Stations (Step 7) to be shown in
this list.
Step 10
Video Link
A. Click the Time and date setting from the menu on left.
B.
If the PC’s date and time is correct, click the
Synchronized with PC
button. If not,
set it manually (see Figure 10.1).
C. Click
Temporarily stored
to save changes.
E. The Zone setting window should now show the stations selected from the list (see Figure 9.1). Repeat process for
remaining zones.
C. Click
Temporarily stored
to save changes.
Figure 9.1: Zone Settings Populated
A. Click Updating the system from the menu on left.
B. Click
Update
to save all data to the IS-CCU. The system will reboot and return
to the language selection screen when complete.
Depending on the amount of data and changes, the reboot could take as long as 5-10 minutes.
Figure 10.1: Time and Date Setting
Step 9: Zone Setting (continued)
Step 10: Time and Date Setting
Step 11: Updating the System
Aiphone Corporation
1700 130th Ave. NE Bellevue, WA 98005
Ph: (800) 692-0200 Fax: (425) 455-0071
www.aiphone.com [email protected]
0314 #95501
8| IS Series Local System Programming Guide
Step 11
Video Link
Step 18
Video Link
/