Kobalt 0267315 User manual

customer service department at 1-888-3KOBALT, 8 a.m. - 8 p.m., EST, Monday - Friday.

Questions, problems, missing parts? Before returning to your retailer, call our

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

KOBALT and the K Design are registered

®®

MODEL SGY-AIR84TZ

ITEM #0267315

AIR HOPPER GUN

Français p.15

Español p. 29

1

AB13431

TABLE OF CONTENTS

2

Safety Information ............................................................................................... 3

Package Contents ............................................................................................... 6

Assembly Instructions .......................................................................................... 7

Operating Instructions .......................................................................................... 8

Care and Maintenance ....................................................................................... 11

10

Troubleshooting ....................................

General Notes ....................................................................................................

.............................................................. 12

Warranty ............................................................................................................. 13

Exploded Views .................................................................................................. 14

Product Specifications .......................... .............................................................. 5

IMPORTANT: To operate correctly, this tool requires airflow that is at least 1.7 cubic feet per

minute (CFM) at 25 pounds per square inch (PSI). Check the specifications of your air compressor

to be sure that it can support both the minimum CFM and PSI required. An air hose may cause

up to 15 PSI drop in pressure, so you may need to set the output higher to maintain the required

pressure at the tool.

1.7

CFM

25

PSI

Tool Requirements

Exigences relatives aux outils

Requisitos de herramientas

@

3

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate

or install the product. If you have any questions regarding the product, please call

customer service at 1-888-3KOBALT, 8:00 a.m.-8:00 p.m., EST, Monday-Friday.

FOR YOUR OWN SAFETY READ AND UNDERSTAND THE OWNER’S MANUAL

BEFORE USING ITEM. FAILURE TO OBSERVE AND FOLLOW THE BELOW

SAFETY INSTRUCTIONS COULD RESULT IN INJURY.

WEAR PROPER PROTECTIVE GEAR

Keep loose hair, loose clothing, or any hanging jewelry away from all moving parts.

Wear protective safety glasses or face shield to protect eyes.

To reduce the risk of hearing damage ensure you use proper ear protection to

safeguard your hearing.

Dress properly and wear protective clothing when needed.

Whenever possible, it’s recommended that electrically non-conductive clothing and

non-skid footwear be worn when using tools.

KEEP CHILDREN AWAY FROM WORK AREA AND TOOL

Keep tool out of reach of children and never allow children to handle equipment or tool.

Keep work area clear from clutter and other work hazards.

Do not use this product in unsafe work conditions.

WORK ENVIRONMENT HAZARDS

Be aware that extension cords and air hoses may present tripping hazards.

Always be aware of your work area surroundings and the people around the work area

to ensure your safety.

Do not operate tool if damaged during shipping, handling, or unsafe transportation of

item.

Using a damaged or unsafe tool can result in serious injury, death, and/or property

damage.

Always check air hoses for weak or worn connections before each use and make

certain that all connections are secure.

Repetitive motions, awkward positions, and exposure to vibration can be harmful to

hands and arms.

Keep hoses away from heat, oil, and sharp edges. Check hoses for weak or worn

connections before each use and make sure that all connections are secure before use.

Never spray in vicinity of flammable materials, open flame, or near ignition sources.

Never store flammable liquids or gases near air compressor or other compressed

materials under pressure.

ADDITIONAL SAFETY GUIDELINES

Every tool has a unique function and is designed to operate in a specific way.

Only use a tool for its intended function.

Always read the label or materials safety data sheet for the materials and/or chemicals

that may be used before you use an item to ensure its safe.

4

SAFETY INFORMATION

Operators must be able to easily handle the bulk weight of the item so that the operator

has full control of the item 100% of the time.

Never operate tool if under the influence of drugs or alcohol.

Never operate tool if you are tired, as operator needs to be in control of tool at all times.

It’s always recommended to have a fire extinguisher and first aid kit near work area.

Keep proper footing at all times

Do not overreach, as slipping, tripping, and/or falling

can be a major cause of serious injury and/or death. Be aware of excess hose left in

working area or work surface. Do not abuse hoses or connectors.

When using air tools, always carry the tool by the handle. Never carry the tool by the

hose or yank it to disconnect it from the air or power supply.

Do not use pressure exceeding the operation pressure of any of the parts (hoses,

fittings, etc.) in the painting system.

If eyes or face come into direct contact with sprayed materials, contact your local

doctor or emergency room for immediate help.

Never aim or spray at yourself or anyone else, which could result in serious injury or

death.

Do not spray acids, corrosive materials, toxic chemicals, fertilizers or pesticides. Using

these materials could result in serious injury and/or death.

Always use a face mask and/or respriator and protective clothing when spraying.

Always spray in a well-ventilated area to prevent health and fire hazards.

Refer to material saftey data sheets (MSDS) of spray materials for details.

Certain materials that can be used with this device can cause skin irritation if they come

into direct contact with the skin. Read the label or materials safety data sheet for the

materials you intend to use to find out which materials may cause skin irritation.

Always disconnect tool from air supply before performing any maintenance.

Never use a tool which is leaking air, has missing or damaged parts, or requires repair.

Only use parts and accessories recommended by the manufacturer.

5

SPECIFICATIONS

GRAVITY

4.5 MM, 6 MM, 8 MM

25 PSI

30 PSI

1.7 SCFM

1/4 IN. NPT

COMPONENT

FEED TYPE

FLUID NOZZLE I.D.

WORKING PRESSURE

MAX. WORKING PRESSURE

REQ’D (SCFM @ 25 PSI)

AIR INLET

PRODUCT SPECIFICATIONS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate

or install the product. If you have any questions regarding the product, please call

customer service at 1-888-3KOBALT, 8:00 a.m.-8:00 p.m., EST, Monday-Friday.

Improper operation or maintenance of this product could result in serious injury and

property damage. Read and understand all warnings and operation instructions

before using this equipment. When using air tools, basic safety precautions should

always be followed to reduce the risk of personal injury.

WARNING

SOME DUST CREATED BY PAINT SPRAYING, POWER SANDING, SAWING,

GRINDING, DRILLING, AND OTHER RELATED ACTIVITIES IS KNOWN TO THE

STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND OTHER

REPRODUCTIVE HARM. A LISTING OF CHEMICALS CAN BE OBTAINED FROM

www.oehha.ca.gov UNDER PROPOSITION 65. SOME EXAMPLES OF THESE

CHEMICALS ARE:

LEAD FROM LEAD BASED PAINTS

CRYSTALLINE SILICA FROM BRICKS, CEMENT AND OTHER MASONRY

PRODUCTS

ARSENIC AND CHROMIUM FROM CHEMICALLY TREATED LUMBER

YOUR RISK FROM THESE EXPOSURES VARIES, DEPENDING ON HOW OFTEN

YOU DO THIS TYPE OF WORK. TO REDUCE YOUR EXPOSURE TO THESE

CHEMICALS WORK IN A WELL VENTILATED AREA, AND WORK WITH

APPROVED

SAFTEY EQUIPMENT, SUCH AS A RESPIRATOR OR DUST MASKS

WHICH ARE

SPECIALLY DESIGNED TO FILTER MICROSOPIC PARTICLES.

PACKAGE CONTENTS

6

DESCRIPTION

Hopper

Flexible Connector

Air Cap

Material Orifice A (d=4.5)

Material Orifice A (d=6)

Trigger

Main Housing

Air Shut-Off Valve

Quick Disconnect

Metal Stand

QUANTITY

1

PART

A

B

C

D

E

F

G

H

Brass Elbow

1

I

Air Inlet Fitting

1

J

K

L

Material Orifice A (d=8) 1M

H

A

B

J

E

C

D

I

G

L M

H

F

K

ASSEMBLY INSTRUCTIONS

7

FOR PISTON/TANK TYPE COMPRESSOR

A.Thread the 90° brass elbow (I) onto

the air inlet fitting (J) at the bottom of the

hopper gun handle.

B.Thread the air shut-off valve (F) onto the

brass elbow.

C.Thread the quick disconnect (G) onto

the air shut-off valve.

FOR ROTARY VANE TYPE COMPRESSOR

A.Thread the 90° brass elbow (I) onto

the air inlet fitting (J) at the bottom of the gun

handle.

B.Thread the quick disconnect (G)

onto the 90° brass elbow (I).

CAUTION: DO NOT install the air shut-off

valve(F) in the hopper gun unless your

compressor has a working pressure switch

for controlling the “on” and “off”.

1. Place the hopper (A) upside down.

2. Place the large end of the flexible

connector (B) over the hopper neck and

slide the gun's hopper receiver onto the

small end of the flexible connector (B).

3. Face the hopper with the handle facing

the rear of the gun and tighten the hopper

clamps.

Attaching The Hopper To The Gun

I

J

G

F

I

J

G

A

B

NOTE There are two different types of air tank/air compressors which can be wsed

with this item.

Estimated Assembly Time: 5-10 minutes

Tools Required for Assembly: Flat screwdriver (not included)

OPERATING INSTRUCTIONS

8

You must consider and deal with the following variables in setting up your

hopper gun to ensure consistent and desired results:

Air Supply: The hopper gun requires a compressor that produces 7 CFM

at 25 PSI. The supply of

air must remain consistent or it will affect the texture.

eht ,erusserp eht rewol ehT :erusserP heavier the texture. The normal

pressure ranges in spans between 10 and 30 PSI. Medium s platter & orange

peel are sprayed at 17-23 PSI.

Material Orifice:

Always use the largest material orifice (8 mm). Medium splatter & orange

peel use the medium material orifice (6 mm).

Trigger Pull Distance:

Distance with the knob on the back of the gun. Adjusting the distance is very

important to maintaining consistency.



1. In this diagram, the hopper is full, the air

is on and flowing from the tip, no pressure

is being applied to the trigger, and no

material is being sprayed.

1

2

2. In this diagram, the hopper is full, the air

is on and flowing, partial pressure is being

applied to the trigger, and some material is

being released from the gun.

OPERATING INSTRUCTIONS

9

3. In this diagram, the hopper is full, the air

is on and flowing, full pressure is being

applied to the trigger, and material is being

released from the gun at an increased rate.

3

PRESSURE

16-21

11-16

16-21

19-24

22-26

TEXTURE

Acoustic

Heavy Splatter

Medium Splatter

Orange Peel

Light Splatter

TRIGGER

PULL

Completely

Two-Thirds

One-Half

One-Third

THICKNESS

Product Directions

Thin

Thick

OPENING

8 mm

6 mm

4.5 mm

TEXTURE TABLE

BEFORE SPRAYING

1. Use tape and heavy canvas drop cloths to protect areas you don't want sprayed. Thin plastic

drop cloths will not provide adequate protection.

2. Do not spray 100% vertically or you will lose efficiency.

3. Plan your path and ensure you have mixed enough material before you begin to avoid

disruption of your work.

4. You should always spray test an old piece of plywood or cardboard before you begin.

5. Always make sure you wear the proper safety equipment when using this item

OPERATING INSTRUCTIONS

10

A. Alw c lacitrev ro llaw ruoy morf .tf 5 ot 3 nigeb sya eiling.

B. Start from the top at an edge or a corner.

C. Move the gun up and down covering the wall vertically in your designated

space. From the bottom, move sideways and work your way up.

D. Repeat this motion from top to bottom, then sideways bottom to top, then

sideways until you have covered the wall.

E. Refill the hopper gun as needed.

SPRAYING WALLS & VAULT CEILINGS VERTICALLY

SPRAYING CEILINGS AND HORIZONTAL SURFACES

A. Fill the hopper gun no more than 75% full with your spray material.

B. Open the shut-off valve and run air through the hopper gun.

C. Lift the hopper gun until it is approximately 1-1/2 to 2 ft. below the ceiling

and angle the gun between 25 and 60 degrees.

D. Always start near a corner or an edge.

E. Begin spraying and move tow eht dra opposite corner or edge.

F. Move backwa ts tuohtiw dr opping and move tow eht dra original starting

corner or edge.

G.

Repeat these procedures until you have covered the entire ceiling.

GENERAL NOTES

The hopper gun will shoot anything that can be gravity fed and atomized (the

degree of atomization is predicated on having the required PSI and CFM

available from the air source).

The compressor should provide a minimum of 7 CFM at 25 PSI.

Make sure your mix can be used with hopper guns by checking the label and

manufacturer's instructions.

You can test mixing one cup of joint compound per hopper to help the flow of

the spray.

Note that the hopper gun does not have an internal valve. If you do not want

air to continuously flow, install the shut-off valve where the hose enters the gun.

Never use the shut-off valve with the compressor. Only use the shut-off valve

with an air compressor that has a reserve tank and an automatic shut-off

switch.

To spray walls, your distance should be 3 to 4 ft.

To spray ceil uoy ,sgni

eht htiw woleb .tf 2 ot 2/1-1 eb dluohs hopper gun

angled 25 - 60 degrees.

CARE AND MAINTENANCE

11

CLEANING YOUR HOPPER GUN

1. Use water to fill and then clean out the hopper. Then reconnect to the air

compressor and blow air through to remove any remaining debris.

2. Make sure the valve is open if you use an air shut-off valve.

3. Turn the hopper gun upside down and lubricate with household oil by

dropping oil in the quick disconnect (with the air shut-off valve in th e open

position). This lubricates the air stem and O-rings.

4. Pull the trigger several times and close the shut-off valve.

ASSEMBLING AND DISASSEMBLING YOUR HOPPER GUN

Taking Your Hopper Gun Apart

1. Take out the material orifice by turning the nut counterclockwise.

2. Remove the knurled knob by turning it counterclockwise until it comes out.

3. Using your finger push the center stem out of the gun through the rear.

TO REASSEMBLE:

1. Before you put the hopper gun back

together wipe a small amount of

lithium-based grease on the O-rings of

the adjustable stop assembly.

2.

Replace the center stem from the rear.

Make sure not to tear up the O-rings when

reassembling.

3.

Replace the knurled knob by turning it

clockwise.

4.

Put in your material orifice and secure

turning the nut clockwise.

Long Term Storage:

Make sure to store in dry secure location.

12

TROUBLESHOOTING

CORRECTIVE ACTION

PROBLEM

SPRAY PATTERN

/CONDITION

a) Material orifice is

clogged.

b) Material around

outside of orifice has

dried.

a) O-ring (Part #9) gets

dry or worn out.

b) Air stem bushing

(Part #8) gets loose.

c) Material orifice loosely

installed, or dirt

between orifice and

body.

a) Adjusting nut

(Part #26) improperly

adjusted.

b) Sluggish air stem.

Material orifice and

stem worn out.

Gun held too far from

surface.

Gun held too close

from surface.

a) Material cannot be

sprayed or sprayed

inefficiently.

b) Will not get a

satisfactory

atomization.

Intermittent spray

Will not get a

satisfactory spray.

Dripping from

material orifice.

Thin, sandy

coarse finish.

Thick, dimpled

finish resembling

orange peel.

a) Soak material orifice in solvent

to loosen clog.

b) Trigger material orifice

several times.

c) Take off air cap and material

orifice, clean orifice using a

bamboo or wooden toothpick.

Then wipe off air cap and

orifice with a rag moistened

with thinner.

d) Reassemble orifice and screw

air cap tight.

a) Back up the gun, put a few

drops of machine oil or replace

with new O-ring.

b) Tighten air stem bushing.

c) Take off air cap and material

orifice, clean dirt and

reassemble orifice and tighten

air cap.

a) Have adjusting nut set to a

good condition.

b) Disassemble the adjusting stop

assembly (Part #18 to #29) as

per the instructions in manual,

wipe a small amount of lithium-

based grease on stem and

O-ring (Part #21), then

reassemble.

Replace with new orifice and

stem.

Move gun closer to surface as

per the instructions in manual.

Move gun further from surface as

per the instructions in manual.

This tool is warranted by the manufacturer to the original purchaser from the original

purchase date for three (3) years subject to the warranty coverage described herein.

This tool is warranted to the original user to be free from defect in material and

workmanship. If you believe that a tool is defective, return the tool, with proper proof

of purchase to the point of purchase. If it is determined that the tool is defective and

covered by this warranty, the distributor will replace the tool or refund the

purchase price.

This warranty is void if: defects in materials or workmanship or damages result from

repairs or alterations which have been made or attempted by others or the

unauthorized use of nonconforming parts; the damage is due to normal wear, damage

is due to abuse (including overloading of the tool beyond capacity), improper

maintenance, neglect or accident; or the damage is due to the use of the tool after

partial failure or use with improper accessories or unauthorized repair or alteration.

This warranty gives you specific legal rights, and you may also have other rights that

vary from state to state.

For warranty questions, call our customer service department at 1-888-3KOBALT,

8:00 a.m.-8:00 p.m. EST, Monday-Friday.

WARRANTY

13

EXPLODED VIEWS

19

20

21

22

23

24

25

26

27

28

29

30

31

32

B

34

A

H

C

K

L

M

5

D

7

8

9

10

11

12

E

F

I

J

G

18

1

4

1

Part No.

Description Qty.

Part No.

Description Qty.

Printed in China

14

KOBALT® and the K Design® are registered

Air Cap

Material Orifice A (d=4.5)

Material Orifice B (d=6)

Material Orifice C (d=8)

Trigger Fixing Bolt

Trigger

“E” Clip

Air Stem Bushing

O-Ring (9*1.8)

Clip Fixing Rivet

Trigger Clip Main Housing

“E” Clip

Main Housing

Air Inlet Fitting

Brass Elbow

Air Shut-Off Valve

Quick Disconnect

Threaded Body

O-Ring (13.5*1.5)

Adjusting Stem

O-Ring (10.6*1.8)

Washer

Adjusting Spring

O-Ring (7.2*1.9)

Screw Seal

Adjusting N

ut

Phillips Screw

Air Stem (back)

Air Stem (front)

O-Ring (33.3*3.5)

Hose Clamp (38-57)

Hose Clamp (44-64)

Flexible Connector

S

Hopper

oft Grip

Metal Stand

.

/

0

Page is loading ...

19

CONSIGNES DE SÉCURITÉ

N’utilisez jamais un outil qui présente une fuite d’air, auquel il manque des pièces,

dont des pièces sont endommagées ou qui nécessite une réparation.

N’utilisez que des pièces et des accessoires recommandés par le fabricant.

CARACTÉRISTIQUES

GRAVITY

4.5 MM, 6 MM, 8 MM

25 LB/PO²

30 LB/PO²

1.7 PI³/MIN

1/4 PO NPT

COMPOSANTE

ALIMENTATION PAR GRAVITÉ

DIAM. INTÉRIEUR DE LA BUSE À PEINTURE

PRESSION DE SERVICE

PRODUCTION NÉCESSAIRE(PI³/MIN À 25 LB/PO²)

ENTRÉE D’AIR

CARACTÉRISTIQUES DU PRODUIT

Une utilisation ou un entretien inadéquat de ce produit peut causer des blessures

graves ou des dommages matériels. Assurez-vous de lire et de comprendre tous

les avertissements et toutes les instructions concernant ceproduit avant de l'utiliser.

Lorsque vous utilisez un outil pneumatique, observez toujours les mesures de

sécurité de base afin de réduire les risques de blessure.

WARNING

Veuillez vous assurer de lire et de comprendre l'intégralité du présent guide avant

d'assembler, d'utiliser ou d'installer ce produit. Si vous avez des questions concernant

ce produit, veuillez téléphoner au service à la clientèle au 1 888 3KOBALT, entre 8 h et

20 h (HNE), du lundi au vendredi.

AVE

R

TISSEMENT

LA POUSSIÈRE CRÉÉE PENDANT LE PONÇAGE, LE SCIAGE, LE POLISSAGE, LE

PERÇAGE ET D'AUTRES ACTIVITÉS PEUT CONTENIR DES PRODUITS CHIMIQUES

RECONNUS PAR L'ÉTAT DE LA CALIFORNIE COMME ÉTANT LA CAUSE DE CANCERS,

D'ANOMALIES CONGÉNITALES ET D'AUTRES PROBLÈMES LIÉS AUX FONCTIONS

AU www.oehha.ca.gov, CONFORMÉMENT À LA PROPOSITION 65. VOICI

QUELQUES-UNS DE CES PRODUITS CHIMIQUES :

DU PLOMB PROVENANT DE PEINTURES À BASE DE PLOMB;

DE LA SILICE CRISTALLINE PROVENANT DE LA BRIQUE, DU CIMENT OU

D'AUTRES MATÉRIAUX DE MAÇONNERIE;

DE L'ARSENIC ET DU CHROME PROVENANT DU BOIS D'ŒUVRE TRAITÉ AVEC

UN PRODUIT CHIMIQUE.

REPRODUCTRICES. VOUS POUVEZ OBTENIR LA LISTE DES PRODUITS CHIMIQUES

LES RISQUES LIÉS À L’EXPOSITION À CES PRODUITS VARIENT SELON LE NOMBRE

DE FOIS OÙ VOUS PRATIQUEZ CES ACTIVITÉS. AFIN DE LIMITER VOTRE

EXPOSITION À CES PRODUITS CHIMIQUES, TRAVAILLEZ DANS UN ENDROIT BIEN

VENTILÉ ET UTILISEZ DE L’ÉQUIPEMENT DE SÉCURITÉ APPROUVÉ, TEL QU’UN

APPAREIL RESPIRATOIRE OU UN MASQUE ANTIPOUSSIÈRE CONÇUS

SPÉCIALEMENT POUR FILTRER LES PARTICULES MICROSCOPIQUES.

AVE

R

TI S SEMENT

PRESSION DE SERVICE MAXIMALE

Page is loading ...

33

ESPECIFICACIONES

GRAVEDAD

4.5 MM, 6 MM, 8 MM

25 PSI

30 PSI

1.7 SCFM

1/4 IN. NPT

COMPONENTE

FEED TYPE

D.I. DE LA BOQUILLA DE FLUIDO

PRESIÓN DE TRABAJO

REQ. (SCFM A 25 PSI)

ENTRADA DE AIRE

ESPECIFICACIONES DEL PRODUCTO

INFORMACIÓN DE SEGURIDAD

El uso o mantenimiento inadecuado de este producto puede ocasionar lesiones

graves y daños a la propiedad. Lea y comprenda todas las advertencias e

instrucciones de funcionamiento antes de usar este equipo. Cuando utilice

herramientas neumáticas, siga siempre las medidas de precaución básicas para

reducir el riesgo de lesiones personales.

ADVERTENCIA

.

ADVERTENCIA

S

)

PARTE DEL POLVO PRODUCIDO POR EL LIJADO, EL SERRUCHADO, LA

TRITURACIÓN Y LA PERFORACIÓN ELÉCTRICA Y OTRAS ACTIVIDADES

RELACIONADAS CONTIENE QUÍMICOS RECONOCIDOS POR EL ESTADO DE

CALIFORNIA COMO CAUSANTES DE CÁNCER, DEFECTOS CONGÉNITOS U OTRO

DAÑOS EN EL APARATO REPRODUCTIVO. SE PUEDE OBTENER UNA LISTA DE LA

SUSTANCIAS QUÍMICAS EN www.oehha.ca.gov BAJO PROPOSITION 65 (PROPUESTA 65

ALGUNOS EJEMPLOS DE ESTAS SUSTANCIAS QUÍMICAS SON:

PLOMO DE PINTURAS A BASE DE PLOMO

SÍLICE CRISTALINA DE LADRILLOS, CEMENTO Y OTROS PRODUCTOS DE

MAMPOSTERÍA

ARSÉNICO Y CROMO DE MADERA TRATADA CON QUÍMICOS

SU RIESGO LUEGO DE ESTAS EXPOSICIONES VARÍA, DEPENDIENDO DE CUÁN

A MENUDO REALICE ESTE TIPO DE TRABAJO. PARA REDUCIR SU EXPOSICIÓN

A ESTOS QUÍMICOS, UTILICE UN EQUIPO DE SEGURIDAD APROBADO, COMO UN

RESPIRADOR O LAS MÁSCARAS PARA POLVO ESPECIALMENTE DISEÑADAS

PARA FILTRAR PARTÍCULAS MICROSCÓPICAS

L

rLea y comprenda completamente este manual antes de intentar ensambla , usar o

instalar el producto. Si tiene preguntas relacionadas con el producto, llame al

Departamento de Servicio al Cliente al 1-888-3KOBA T, de lunes a viernes de

8:00 a.m. a 8:00 p.m., hora estándar del Este.

PRESIÓN DE TRABAJO MÁXIMA

Page is loading ...

Kobalt 0267315 User manual

This manual is also suitable for

Kobalt 0267315 User manual

in other languages

Related papers

Other documents