Commell LV-671CM6 User manual

Category
Motherboards
Type
User manual

Commell LV-671CM6 is an industrial-grade Mini-ITX motherboard featuring an embedded Intel Celeron M processor, DDR2 memory support, and a range of expansion options. With its compact size and low power consumption, it is suitable for embedded, industrial automation, and IoT applications.

Key features of the Commell LV-671CM6 include:

  • Intel Celeron M processor for reliable and efficient performance
  • DDR2 memory support for up to 1GB of memory
  • Mini-PCIe and Mini-AGP expansion slots for additional functionality
  • Dual display support via LVDS and VGA ports
  • 5.1 channel audio with S/PDIF output

Commell LV-671CM6 is an industrial-grade Mini-ITX motherboard featuring an embedded Intel Celeron M processor, DDR2 memory support, and a range of expansion options. With its compact size and low power consumption, it is suitable for embedded, industrial automation, and IoT applications.

Key features of the Commell LV-671CM6 include:

  • Intel Celeron M processor for reliable and efficient performance
  • DDR2 memory support for up to 1GB of memory
  • Mini-PCIe and Mini-AGP expansion slots for additional functionality
  • Dual display support via LVDS and VGA ports
  • 5.1 channel audio with S/PDIF output
LV-671Z
Mini-ITX Motherboard
Users Manual
Edition: 1.12
2005/3/24
LV-671Z Users Manual
2
LV-671Z Users Manual
3
LV-671Z User’s Manual
4
Copyright
Copyright
©
2003 - 2004. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to
make improvements to the products.
This document contains proprietary information and protected by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at
http://www.commell.com.tw.
LV-671Z User’s Manual
5
Packing List
Please check the package before you use this product
Hardware:
LV-671Z Mini-ITX motherboard x 1
Cable Kit:
40-pin ATA100 IDE Cable x 1
26-pin Slim Type Floppy Cable x 1
4-pin to 4-pin Power Cable x 1
CD Content
Driver
User’s Manual
LV-671Z User’s Manual Index
6
Index
Chapter 1 <Introduction>.....................................................................................9
1.1 <Product Overview>.................................................................................9
1.2 <Product Specification> .........................................................................10
1.3 <Component Placement> ......................................................................13
1.4 <Block Diagram>....................................................................................14
Chapter 2 <Hardware Setup>.............................................................................15
2.1 <Connector Location>............................................................................15
2.2 <Jumper Reference> .............................................................................16
2.3 <Connector Reference>.........................................................................17
2.3.1 <Internal Connector>..................................................................17
2.3.2 <External I/O connector> ...........................................................17
2.4 <System Setup>.....................................................................................18
2.4.1 <Memory Installation>................................................................18
2.5 <CMOS Setup>......................................................................................19
2.6 <IDE Interface>......................................................................................20
2.7 Compact Flash Interface........................................................................21
2.8 <Display Interface>................................................................................22
2.8.1 <Analog display interface>.........................................................22
2.8.2 <Digital display interface> ..........................................................22
2.9 <Audio Interface>...................................................................................26
2.10 <Ethernet Interface> ............................................................................28
2.11 <Power and Fan connector>................................................................29
2.12 <GPIO Interface>.................................................................................31
2.13 <Expansive Interface> .........................................................................32
2.14 <Switch and Indicator>.........................................................................33
Chapter 3 <System Setup> ................................................................................35
3.1 <Watchdog Timer Setting>.....................................................................35
3.2 <Audio Setting>......................................................................................36
3.3 <Display Device Setup>.........................................................................37
LV-671Z User’s Manual Index
7
Chapter 4 <BIOS Setup> ....................................................................................41
Appendix A <I/O Port Pin Assignment>............................................................43
A.1 <IDE Port>.............................................................................................43
A.2 <Floppy Port> ........................................................................................45
A.3 < USB Interface >..................................................................................45
A.4 <IrDA Port>............................................................................................46
A.5 < VGA Port >..........................................................................................46
A.6 < LAN Port >..........................................................................................46
A.7 < Serial Port >........................................................................................47
Appendix B <Flash BIOS>..................................................................................49
B.1 <Flash Tool> ..........................................................................................49
B.2 <Flash BIOS Procedure>.......................................................................49
Appendix C <System Resource> ......................................................................51
C.1 <I/O Address Map>................................................................................51
C.2 <Memory Address Map> .......................................................................53
C.3 <System IRQ and DMA Resource>.......................................................54
Contact Information............................................................................................56
LV-671Z User’s Manual
8
(This Page is Left for Blank)
LV-671Z User’s Manual Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
LV-671Z is an all-in-one industrial compact Pentium-M level motherboard based on
Mini-ITX form factor at 170 x 170 mm of dimension. Based on Intel 852GM and ICH4
chipset, LV-671Z offers the compact, embedded, value and high performance solution with
Intel Celeron M CPU, 400 MHz of FSB, 1GBytes DDR200/266 SDRAM, Intel 852GM
GMCH built-in Intel Extreme Graphics Technology, Intel PRO/1000+ LAN, Hi-Speed USB
2.0, 5.1 channel and S/P DIF 3D audio, 18/24-bit dual channel LVDS, GPIO and
embedded flash disk interfaces.
Low Power Consumption Solution
Based on Intel 852GM chipset and Intel Celeron M processor, the board requires
lower power consumption than Pentium 4 –M processors. The embedded Intel Celeron M
of ultra low voltage provides the ability for fanless system.
Dual Display Architecture
Intel 852GM supports independent display interface; users can apply two display
devices for dual display clone or extended desktop display. With this feature, system
integrator can use this board for Kiosk, ATM, or industrial control machines.
5.1 Channel AC97 Audio
LV-671Z integrates a REALTEK 5.1 channel AC97 codec; users can enjoy the live
surround sound through 5.1 channel speakers. LV-671Z also has an S/PDIF jack for digital
sound outputting.
Hi-Speed USB 2.0 Interface
Intel ICH4 built-in Hi-Speed USB 2.0 controller let LV-671Z offer up to 480Mbps of
transferring rate.
Card Bus and Embedded Flash Disk
The LV-671Z support PCMCIA Type I/II enable you can simply use the wireless LAN
module or other extended devices, the Compact Flash interface and IDE1 with DOM
support can let you port any embedded system onboard.
Mini-PCI and Mini-AGP interface
With Mini-PCI interface, users can add a wireless LAN module or video capture
module for powerful communication solutions. With Mini-AGP interface, users can apply
the additional video output module such as HDTV or DVI.
Product Overview 9
LV-671Z User’s Manual Introduction
1.2 <Product Specification>
General Specification
Form Factor Mini-ITX motherboard at 170 x 170 mm (L x W)
CPU Embedded Intel Celeron M 600MHz
Package: mBGA 479
FSB: 400MHz
Memory 1GBytes DDR200/266 SDRAM on one 184-pin DIMM socket
Unbuffered, non-ECC supported
Chipset Intel 82852GM GMCH and 82801DB ICH4
BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock Intel ICH4 built-in RTC with lithium battery
Enhanced IDE PCI enhanced IDE interface supports dual channels and up to 4
ATAPI devices at UltraATA/100
One 40-pin and one 44-pin IDE port
DiskOnModule (DOM) embedded flash disk up to 1GBytes
Multi-I/O Port
Chipset Intel 82801DB ICH4 (USB) and Winbond W83627HF-AW LPC
Super I/O controller
Serial Port Two external RS-232 serial port with 16C550 compatible UART
and 16 bytes FIFO
USB Port Six Hi-Speed USB 2.0 ports with 480 Mbps of transfer rate
Two external and four internal USB ports
Parallel Port One external bi-direction parallel port with SPP/ECP/EPP mode
Floppy Port One slim-type FDD port supports up to two FDD
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel
GPIO One 20-pin Digital I/O connector with 15-bit programmable I/O
interface
Card Bus
PCMCIA One PCMCIA Type I/II slot
Product Specification 10
LV-671Z User’s Manual Introduction
VGA Display Interface
Chipset Intel 852GM GMCH built-in Intel Extreme Graphics Technology
With 133MHz VGA core and 256-bit 3D engine
Frame Buffer Intel DVMT (Dynamic Video Memory Technology) 2.0 up to
64Mbytes shared with system*
Display Type CRT and LCD monitors for analog display
24-bit single/dual channel LCD panel for digital display
Connector External DB15 female connector on rear I/O panel
Internal 40-pin LVDS connector
*Under Windows 98/ME/2000/XP/Server2003 or Linux kernel 2.4 later
Ethernet Interface
Chipset Intel PRO/1000+ LAN interface with Intel 82540EM
Type 10Base-T / 100Base-TX/1000Base-T,
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector External RJ45 connector with LED on rear I/O panel
Audio Interface
Chipset Intel ICH4 with REALTEK ALC655 AC97 3D audio codec
Interface 5.1 channel 3D audio with front (R/L), rear (R/L), center and bass
Optical Fiber digital audio encoding signal output
Connector Optional external three phone jack for 5.1 channel audio onboard
External Amplified Speaker output jack on rear panel
External SPDIF connector on rear panel
Internal 10-pin header for line-in/-out, MIC-out, 4-pin header for
CD-in
Solid State Disk Interface
Flash Type Compact Flash Type-I/II for Compact Flash Card or IBM Micro Drive
Capacity Up to 1GB flash memory
Expansion Interface
Slim PCI Slot One slim type PCI slot supports up to 2 bus master PCI
32-bit, 33MHz
Mini-PCI One Mini-PCI socket with 32-bit, 33MHz for LV-671ZMP series
Mini-AGP One Mini-AGP socket with DVO bus for LV-671ZMA series
Product Specification 11
LV-671Z User’s Manual Introduction
Power and Environment
Power
Requirement
One external 19V/12V (auto switching) DC Adapter connector on
rear panel
4-pin onboard 12V P4 4-pin power connector
(Two power resources selectable for each)
Input Voltage
Range
11V ~ 13V for 12V power supply
16V ~ 20V for 19V power supply
Input Current 12V/60W (with one 5.25” CDROM and 3.5” HDD)
19V/60W (with one 5.25” CDROM and 3.5” HDD)
Dimension 170 (L) x 170 (H) mm, Mini-ITX form factor
Temperature Operating within 0 ~ 60
o
C (32 ~ 140
o
F)
Storage within -20 ~ 85
o
C (-4 ~ 185
o
F)
Ordering Code
LV-671ZMA Embedded Mini-ITX Intel Celeron M processor Motherboard
with Intel Extreme VGA, LAN, 5.1-CH/SPDIF Audio,
Hi-Speed USB 2.0, mini-AGP socket and LVDS interface.
LV-671ZMP Embedded Mini-ITX Intel Celeron M processor Motherboard
with Intel Extreme VGA, LAN, 5.1-CH/SPDIF Audio,
Hi-Speed USB 2.0, mini-PCI socket and LVDS interface.
LV-671ZNSMA Same as LV-671ZMA but without PCMCIA & Compact Flash
LV-671ZNSMP Same as LV-671ZMP but without PCMCIA & Compact Flash
For further product information please visit the website at http://www.commell.com.tw
Product Specification 12
LV-671Z User’s Manual Introduction
1.3 <Component Placement>
1 x 184-pin DDR266 DIMM up to 1GB
Intel 852GM
(Northbridge)
Intel ICH4
(Southbridge)
Embedded
Intel Celeron M
600MHz
Onboard DC
to DC inverter
Intel 82540EM
Gigabit LAN
REALTEK
ALC655 5.1CH
A
udio Codec
Component Placement 13
LV-671Z User’s Manual Introduction
1.4 <Block Diagram>
400MHz FSB
852GM
CRT
DVO B/C
Mini-AGP
ICH4
ATAPI Devices
USB Devices
480Mb/s
UltraATA100
USB2.0
Audio
AC97 Codec
Compact Flash
IrDA
PS/2
COM Port
Parallel
Port
Floppy
LPC
33MHz
PCI Bus
PCMCIA
Mini-PCI
Slim PCI
Gigabit Ethernet
Controller
DDR200/266
1 x 184-pin
DIMM
Up to 1GB
LVDS
LVDS
LCD
Embedded Intel Celeron M 600MHz CPU
Block Diagram 14
LV-671Z User’s Manual Hardware Setup
Chapter 2 <Hardware Setup>
This chapter contains the information for installation of hardware. The install procedure
includes jumper settings, CPU and memory installation, fan, I/O and panel connections.
2.1 <Connector Location>
CN_BPWR CN_INV DIMM IDE1 CN_LVDS IDE2 CN_USB1 CN_USB2
MINI_AGP
MINIPCI
CN_IR
CPUFAN
CN 12V
CN_SPWR
JFRNT
SYSFAN
CN_DIO
PCI
FDD
CN_WOL
CN_AUDIO
CDIN
CN_2ND_IO CN_LAN2
DC_IN PS/2 Printer LAN COM2/1
VGA SPEAKER SP/DIF Dual_USB PCMCIA
Connector Location 15
LV-671Z User’s Manual Hardware Setup
2.2 <Jumper Reference>
Jumper Function
JRTC COMS Operate / Clear Setting
JLAN LAN1 Enable/Disable
JVLCD LCD Panel Voltage Setting
JCFSEL Compact Flash Address Setting
JDOM IDE1 5V Voltage Enable/Disable
JDOM JCFSEL JVLCD
JRTC
JLAN
Jumper Reference 16
LV-671Z User’s Manual Hardware Setup
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DIMM 184-pin DIMM Socket Standard
IDE1 40-pin Primary IDE Port Standard
IDE2 44-pin Secondary IDE Port Standard
FDD 26-pin slim type FDD Port Standard
CN_USB1 10-pin 3
rd
/ 4
th
Hi-Speed USB 2.0 Port Standard
CN_USB2 10-pin 5
th
/ 6
th
Hi-Speed USB 2.0 Port Standard
CN_IR 5-pin SIR IrDA Port Standard
CN_12V 4-pin AT Power Connector Standard
CN_BPWR 4-pin 5V&12V output connector Standard
CN_SPWR 4-pin 5V&12V output connector Standard
JFRNT 14-pin Switch and Indicator Connector Standard
CPUFAN 3-pin +12V CPU Fan Connector Standard
SYSFAN 3-pin +12V System Fan Connector Standard
CN_AUDIO 10-pin Audio Port Standard
CDIN 4-pin CD-in Interface Standard
CN_WOL 3-pin Wake-On-LAN Interface Standard
CN_LVDS 40-pin LVDS connector Standard
CN_INV 5-pin LCD Inverter Power Connector Standard
CN_DIO 20-pin programmable I/O connector Standard
CN_LAN2 Additional Ethernet Controller Interface Standard
CN_2ND_IO Additional I/O module interface Standard
CF Compact Flash Card Interface Standard
PCMCIA PCMCIA Card bus interface Standard
2.3.2 <External I/O connector>
Connector Function Remark
DC_IN 4-pin 12V/19V auto-switching input Standard
PS2 PS/2 type keyboard and mouse port Standard
Printer DB26 parallel port Standard
VGA DB15 VGA port Standard
SPEAKER Amplified speaker out Standard
SPDIF Digital audio output Standard
LAN RJ45 LAN port Standard
DUAL_USB USB connectors Standard
COM1/2 RS232 DB9 serial port Standard
PCMCIA Car bus slot Standard
Connector Reference 17
LV-671Z User’s Manual Hardware Setup
2.4 <System Setup>
2.4.1 <Memory Installation>
The board supports one 184-pin DDR200/266 (PC1600/PC2100) SDRAM up to 1GB of
capacity, and supports non-ECC, unbuffered memory modules.
DIMM
104-pin 80-pin
Please check the pin number to match the socket side well
before installing memory module.
Memory Installation 18
LV-671Z User’s Manual Hardware Setup
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin Header
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
1
3
JRTC
CMOS Setup 19
LV-671Z User’s Manual Hardware Setup
2.6 <IDE Interface>
The board supports two IDE interface up to 4 ATAPI devices, base on Intel ICH4, the IDE
interface supports ATA66/100 ATAPI drives. The IDE1 supports +5V on pin-20 for DOM
(Disk on Module), the jumper JDOM can let you select enable/disable this support.
Jumper: JDOM
Type: onboard 3-pin header
JDOM Mode
ON IDE1 pin-20 5V power supply enable
OFF No 5V power supply on IDE1 pin-20
Default setting
39
1
JDOM
IDE1 (40-pin pitch=2.54)
40
2
1
43
IDE2 (44-pin pitch=2.00)
2
44
IDE Interface 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Commell LV-671CM6 User manual

Category
Motherboards
Type
User manual

Commell LV-671CM6 is an industrial-grade Mini-ITX motherboard featuring an embedded Intel Celeron M processor, DDR2 memory support, and a range of expansion options. With its compact size and low power consumption, it is suitable for embedded, industrial automation, and IoT applications.

Key features of the Commell LV-671CM6 include:

  • Intel Celeron M processor for reliable and efficient performance
  • DDR2 memory support for up to 1GB of memory
  • Mini-PCIe and Mini-AGP expansion slots for additional functionality
  • Dual display support via LVDS and VGA ports
  • 5.1 channel audio with S/PDIF output

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI